- 01 Oct, 2020 4 commits
-
-
Ido Schimmel authored
The old probe functions that were invoked by drop monitor code are no longer called and can thus be removed. They were replaced by actual probe functions that are registered on the recently introduced 'devlink_trap_report' tracepoint. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Convert drop monitor to use the recently introduced 'devlink_trap_report' tracepoint instead of having devlink call into drop monitor. This is both consistent with software originated drops ('kfree_skb' tracepoint) and also allows drop monitor to be built as a module and still report hardware originated drops. Signed-off-by: -
Ido Schimmel authored
Drop monitor supports two alerting modes: Summary and packet. Prepare a probe function for each, so that they could be later registered on the devlink tracepoint by calling register_trace_devlink_trap_report(), based on the configured alerting mode. Signed-off-by:
-
Ido Schimmel authored
Add a tracepoint for trap reports so that drop monitor could register its probe on it. Use trace_devlink_trap_report_enabled() to avoid wasting cycles setting the trap metadata if the tracepoint is not enabled. Signed-off-by:
-
- 30 Sep, 2020 36 commits
-
-
David S. Miller authored
Merge tag 'linux-can-next-for-5.10-20200930' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2020-09-30 this is a pull request of 13 patches for net-next. The first 10 target the mcp25xxfd driver (which is renamed to mcp251xfd during this series). The first two patches are by Thomas Kopp, which adds reference to the just related errata and updates the documentation and log messages. Dan Carpenter's patch fixes a resource leak during ifdown. A patch by me adds the missing initialization of a variable. Oleksij Rempel updates the DT binding documentation as requested by Rob Herring. The next 5 patches are by Thomas Kopp and me. During review Geert Uytterhoeven suggested to use "microchip,mcp251xfd" instead of "microchip,mcp25xxfd" as the DT autodetection compatible to avoid clashes with future but incompatible devices. We decided not only to rename the compatible but the whole driver from "mcp25xxfd" to "mcp251xfd". This is done in several patches. Joakim Zhang contributes three patches for the flexcan driver. The first one adds support for the ECC feature, which is implemented on some modern IP cores, by initializing the controller's memory during ifup. The next patch adds support for the i.MX8MP (which supports ECC) and the last patch properly disables the runtime PM if device registration fails. ==================== Signed-off-by:
-
David S. Miller authored
Shannon Nelson says: ==================== ionic watchdog training Our link watchdog displayed a couple of unfriendly behaviors in some recent stress testing. These patches change the startup and stop timing in order to be sure that expected structures are ready to be used by the watchdog. ==================== Signed-off-by: -
Shannon Nelson authored
In one corner case scenario, the driver device lif setup can get delayed such that the ionic_watchdog_cb() timer goes off before the ionic->lif is set, thus causing a NULL pointer panic. We catch the problem by checking for a NULL lif just a little earlier in the callback. Signed-off-by:
Shannon Nelson <snelson@pensando.io> Signed-off-by:
-
Shannon Nelson authored
We need to be better at making sure we don't have a link check watchdog go off while we're shutting things down, so let's stop the timer as soon as we start the remove. Meanwhile, since that was the only thing in ionic_dev_teardown(), simplify and remove that function. Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== tcp: exponential backoff in tcp_send_ack() We had outages caused by repeated skb allocation failures in tcp_send_ack() It is time to add exponential backoff to reduce number of attempts. Before doing so, first patch removes icsk_ack.blocked to make room for a new field (icsk_ack.retry) ==================== Signed-off-by: -
Eric Dumazet authored
Whenever host is under very high memory pressure, __tcp_send_ack() skb allocation fails, and we setup a 200 ms (TCP_DELACK_MAX) timer before retrying. On hosts with high number of TCP sockets, we can spend considerable amount of cpu cycles in these attempts, add high pressure on various spinlocks in mm-layer, ultimately blocking threads attempting to free space from making any progress. This patch adds standard exponential backoff to avoid adding fuel to the fire. Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Eric Dumazet authored
TCP has been using it to work around the possibility of tcp_delack_timer() finding the socket owned by user. After commit 6f458dfb ("tcp: improve latencies of timer triggered events") we added TCP_DELACK_TIMER_DEFERRED atomic bit for more immediate recovery, so we can get rid of icsk_ack.blocked This frees space that following patch will reuse. Signed-off-by:
-
Alexandre Belloni authored
struct macb_platform_data is only used by macb_pci to register the platform device, move its definition to cadence/macb.h and remove platform_data/macb.h Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
David S. Miller authored
Petr Machata says: ==================== mlxsw: PFC and headroom selftests Recent changes in the headroom management code made it clear that an automated way of testing this functionality is needed. This patchset brings two tests: a synthetic headroom behavior test, which verifies mechanics of headroom management. And a PFC test, which verifies whether this behavior actually translates into a working lossless configuration. Both of these tests rely on mlnx_qos[1], a tool that interfaces with Linux DCB API. The tool was originally written to work with Mellanox NICs, but does not actually rely on anything Mellanox-specific, and can be used for mlxsw as well as for any other NIC-like driver. Unlike Open LLDP it does support buffer commands and permits a fire-and-forget approach to configuration, which makes it very handy for writing of selftests. Patches #1-#3 extend the selftest devlink_lib.sh in various ways. Patch #4 then adds a helper wrapper for mlnx_qos to mlxsw's qos_lib.sh. Patch #5 adds a test for management of port headroom. Patch #6 adds a PFC test. [1] https://github.com/Mellanox/mlnx-tools/ ==================== Signed-off-by:
-
Petr Machata authored
Add a test for PFC. Runs 10MB of traffic through a bottleneck and checks that none of it gets lost. Signed-off-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
-
Petr Machata authored
Add a test for headroom configuration. This covers projection of ETS configuration to ingress, PFC, adjustments for MTU, the qdisc / TC mode and the effect of egress SPAN session on buffer configuration. Signed-off-by:
-
Petr Machata authored
mlnx_qos is a script for configuration of DCB. Despite the name it is not actually Mellanox-specific in any way. It is currently the only ad-hoc tool available (in contrast to a daemon that manages an interface on an ongoing basis). However, it is very verbose and parsing out error messages is not really possible. Add a wrapper that makes it easier to use the tool. Signed-off-by:
-
Petr Machata authored
Some selftests may not need any actual ports. Technically those are not forwarding selftests, but devlink_lib can still be handy. Fall back on NETIF_NO_CABLE in those cases. Signed-off-by:
-
Petr Machata authored
Add a helper that answers the cell size of the devlink device. Signed-off-by:
-
Petr Machata authored
Changing pool type from static to dynamic causes reinterpretation of threshold values. They therefore need to be saved before pool type is changed, then the pool type can be changed, and then the new values need to be set up. For that reason, set cannot subsume save, because it would be saving the wrong thing, with possibly a nonsensical value, and restore would then fail to restore the nonsensical value. Thus extract a _save() from each of the relevant _set()'s. This way it is possible to save everything up front, then to tweak it, and then restore in the required order. Signed-off-by:
-
Joakim Zhang authored
Disable runtime PM if register flexcandev failed, and balance reference of usage_count. Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Link: https://lore.kernel.org/r/20200929211557.14153-4-qiangqing.zhang@nxp.comSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Joakim Zhang authored
Add flexcan driver for i.MX8MP, which supports CAN FD and ECC. Signed-off-by:
-
Joakim Zhang authored
One issue was reported at a baremetal environment, which is used for FPGA verification. "The first transfer will fail for extended ID format(for both 2.0B and FD format), following frames can be transmitted and received successfully for extended format, and standard format don't have this issue. This issue occurred randomly with high possiblity, when it occurs, the transmitter will detect a BIT1 error, the receiver a CRC error. According to the spec, a non-correctable error may cause this transfer failure." With FLEXCAN_QUIRK_DISABLE_MECR quirk, it supports correctable errors, disable non-correctable errors interrupt and freeze mode. Platform has ECC hardware support, but select this quirk, this issue may not come to light. Initialize all FlexCAN memory before accessing them, at least it can avoid non-correctable errors detected due to memory uninitialized. The internal region can't be initialized when the hardware doesn't support ECC. According to IMX8MPRM, Rev.C, 04/2020. There is a NOTE at the section 11.8.3.13 Detection and correction of memory errors: "All FlexCAN memory must be initialized before starting its operation in order to have the parity bits in memory properly updated. CTRL2[WRMFRZ] grants write access to all memory positions that require initialization, ranging from 0x080 to 0xADF and from 0xF28 to 0xFFF when the CAN FD feature is enabled. The RXMGMASK, RX14MASK, RX15MASK, and RXFGMASK registers need to be initialized as well. MCR[RFEN] must not be set during memory initialization." Memory range from 0x080 to 0xADF, there are reserved memory (unimplemented by hardware, e.g. only configure 64 MBs), these memory can be initialized or not. In this patch, initialize all flexcan memory which includes reserved memory. In this patch, create FLEXCAN_QUIRK_SUPPORT_ECC for platforms which has ECC feature. If you have a ECC platform in your hand, please select this qurik to initialize all flexcan memory firstly, then you can select FLEXCAN_QUIRK_DISABLE_MECR to only enable correctable errors. Signed-off-by:
-
Marc Kleine-Budde authored
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver, which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming, but incompatible chips. In the previous patch the autodetect DT compatbile has been renamed to "microchip,mcp251xfd", this patch changes all non user facing occurrence of "mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD". [1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com Link: https://lore.kernel.org/r/20200930091424.792165-10-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver, which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming, but incompatible chips. In the previous patch the autodetect DT compatbile has been renamed to "microchip,mcp251xfd", this patch changes all user facing strings from "mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD", including: - kconfig symbols - name of kernel module - DT and SPI compatible [1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com Link: https://lore.kernel.org/r/20200930091424.792165-9-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver, which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming, but incompatible chips. In the previous patch the autodetect DT compatbile has been renamed to "microchip,mcp251xfd", this patch changes the name of the driver subdir and the individual files accordinly. [1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com Link: https://lore.kernel.org/r/20200930091424.792165-8-mkl@pengutronix.deSigned-off-by:
-
Thomas Kopp authored
The wildcard should be narrowed down to prevent existing and future devices that are not compatible from matching. It is very unlikely that incompatible devices will be released that do not match the wildcard. Discussion Reference: https://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.comReported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Thomas Kopp <thomas.kopp@microchip.com> Link: https://lore.kernel.org/r/20200930091423.755-1-thomas.kopp@microchip.comSigned-off-by:
-
Thomas Kopp authored
The wildcard should be narrowed down to prevent existing and future devices that are not compatible from matching. It is very unlikely that incompatible devices will be released that do not match the wildcard. This is the documentation part of the commit. Discussion Reference: https://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.comReported-by:
-
Oleksij Rempel authored
Apply following fixes: - Use 'interrupts'. (interrupts-extended will automagically be supported by the tools) - *-supply is always a single item. So, drop maxItems=1 - add "additionalProperties: false" flag to detect unneeded properties. Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20200923125301.27200-1-o.rempel@pengutronix.deReported-by:
Rob Herring <robh@kernel.org> Reviewed-by:
-
Marc Kleine-Budde authored
This patch fixes the following warning: drivers/net/can/spi/mcp25xxfd/mcp25xxfd-core.c:2155 mcp25xxfd_irq() error: uninitialized symbol 'set_normal_mode'. by adding the missing initialization. Reported-by:Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Fixes: 55e5b97f ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Link: https://lore.kernel.org/r/20200923114726.2704426-1-mkl@pengutronix.deSigned-off-by:
-
Dan Carpenter authored
This loop doesn't free the first element of the array. The "i > 0" has to be changed to "i >= 0". Fixes: 55e5b97f ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Signed-off-by:
-
Thomas Kopp authored
This patch adds a reference to the recent released MCP2517FD and MCP2518FD errata sheets and paste the explanation. The driver already implements the proposed fix. Signed-off-by:
-
Thomas Kopp authored
This patch adds a reference to the recent released MCP2517FD and MCP2518FD errata sheets and paste the explanation. The single error correction does not always work, so always indicate that a single error occurred. If the location of the ECC error is outside of the TX-RAM always use netdev_notice() to log the problem. For ECC errors in the TX-RAM, there is a recovery procedure. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== HW support for VCAP IS1 and ES0 in mscc_ocelot The patches from RFC series "Offload tc-flower to mscc_ocelot switch using VCAP chains" have been split into 2: https://patchwork.ozlabs.org/project/netdev/list/?series=204810&state=* This is the boring part, that deals with the prerequisites, and not with tc-flower integration. Apart from the initialization of some hardware blocks, which at this point still don't do anything, no new functionality is introduced. - Key and action field offsets are defined for the supported switches. - VCAP properties are added to the driver for the new TCAM blocks. But instead of adding them manually as was done for IS2, which is error prone, the driver is refactored to read these parameters from hardware, which is possible. - Some improvements regarding the processing of struct ocelot_vcap_filter. - Extending the code to be compatible with full and quarter keys. This series was tested, along with other patches not yet submitted, on the Felix and Seville switches. ==================== Signed-off-by:
-
Vladimir Oltean authored
Currently a new filter is created, containing just enough correct information to be able to call ocelot_vcap_block_find_filter_by_index() on it. This will be limiting us in the future, when we'll have more metadata associated with a filter, which will matter in the stats() and destroy() callbacks, and which we can't make up on the spot. For example, we'll start "offloading" some dummy tc filter entries for the TCAM skeleton, but we won't actually be adding them to the hardware, or to block->rules. So, it makes sense to avoid deleting those rules too. That's the kind of thing which is difficult to determine unless we look up the real filter. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
And rename the existing find to ocelot_vcap_block_find_filter_by_index. The index is the position in the TCAM, and the id is the flow cookie given by tc. Signed-off-by:
-
Vladimir Oltean authored
The 'cnt' variable is actually used for 2 purposes, to hold the number of sub-words per VCAP entry, and the number of sub-words per VCAP action. In fact, I'm pretty sure these 2 numbers can never be different from one another. By hardware definition, the entry (key) TCAM rows are divided into the same number of sub-words as its associated action RAM rows. But nonetheless, let's at least rename the variables such that observations like this one are easier to make in the future. Signed-off-by:
-
Vladimir Oltean authored
This gets rid of one of the 2 variables named, very generically, "count". Signed-off-by:
-
Xiaoliang Yang authored
When calculating the offsets for the current entry within the row and placing them inside struct vcap_data, the function assumes half key entry (2 keys per row). This patch modifies the vcap_data_offset_get() function to calculate a correct data offset when the setting VCAP Type-Group of a key to VCAP_TG_FULL or VCAP_TG_QUARTER. This is needed because, for example, VCAP ES0 only supports full keys. Also rename the 'count' variable to 'num_entries_per_row' to make the function just one tiny bit easier to follow. Signed-off-by:
Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
When we'll make the switch to multiple chain offloading, we'll want to know first what VCAP block the rule is offloaded to. This impacts what keys are available. Since the VCAP block is determined by what actions are used, parse the action first. Signed-off-by:
-
Vladimir Oltean authored
Now that we are deriving these from the constants exposed by the hardware, we can delete the static info we're keeping in the driver. Signed-off-by:
-
