- 12 May, 2022 5 commits
-
-
Bin Chen authored
Add VF rate limit feature This patch enhances the NFP driver to supports assignment of both max_tx_rate and min_tx_rate to VFs The template of configurations below is all supported. e.g. # ip link set $DEV vf $VF_NUM max_tx_rate $RATE_VALUE # ip link set $DEV vf $VF_NUM min_tx_rate $RATE_VALUE # ip link set $DEV vf $VF_NUM max_tx_rate $RATE_VALUE \ min_tx_rate $RATE_VALUE # ip link set $DEV vf $VF_NUM min_tx_rate $RATE_VALUE \ max_tx_rate $RATE_VALUE The max RATE_VALUE is limited to 0xFFFF which is about 63Gbps (using 1024 for 1G) Signed-off-by:
Bin Chen <bin.chen@corigine.com> Signed-off-by:
Louis Peens <louis.peens@corigine.com> Signed-off-by:
Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Bin Chen authored
When calling ndo_set_vf_rate() the max_tx_rate parameter may be zero, in which case the setting is cleared, or it must be greater or equal to min_tx_rate. Enforce this requirement on all calls to ndo_set_vf_rate via a wrapper which also only calls ndo_set_vf_rate() if defined by the driver. Based on work by Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a dev_dbg message. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20220511104448.150800-1-colin.i.king@gmail.comSigned-off-by:
-
Vladimir Oltean authored
Right now, a PHY-less port (no phy-mode, no fixed-link, no phy-handle) doesn't register with phylink, but calls netif_carrier_on() from enetc_start(). This makes sense for a VF, but for a PF, this is braindead, because we never call enetc_mac_enable() so the MAC is left inoperational. Furthermore, commit 71b77a7a ("enetc: Migrate to PHYLINK and PCS_LYNX") put the nail in the coffin because it removed the initial netif_carrier_off() call done right after register_netdev(). Without that call, netif_carrier_on() does not call linkwatch_fire_event(), so the operstate remains IF_OPER_UNKNOWN. Just deny the broken configuration by requiring that a phy-mode is present, and always register a PF with phylink. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220511094200.558502-1-vladimir.oltean@nxp.comSigned-off-by:
-
Kees Cook authored
As we continue to narrow the scope of what the FORTIFY memcpy() will accept and build alternative APIs that give the compiler appropriate visibility into more complex memcpy scenarios, there is a need for "unfortified" memcpy use in rare cases where combinations of compiler behaviors, source code layout, etc, result in cases where the stricter memcpy checks need to be bypassed until appropriate solutions can be developed (i.e. fix compiler bugs, code refactoring, new API, etc). The intention is for this to be used only if there's no other reasonable solution, for its use to include a justification that can be used to assess future solutions, and for it to be temporary. Example usage included, based on analysis and discussion from: https://lore.kernel.org/netdev/CANn89iLS_2cshtuXPyNUGDPaic=sJiYfvTb_wNLgWrZRyBxZ_g@mail.gmail.com Cc: Jakub Kicinski <kuba@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Coco Li <lixiaoyan@google.com> Cc: Tariq Toukan <tariqt@nvidia.com> Cc: Saeed Mahameed <saeedm@nvidia.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: netdev@vger.kernel.org Cc: linux-hardening@vger.kernel.org Signed-off-by:
Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20220511025301.3636666-1-keescook@chromium.orgSigned-off-by:
-
- 11 May, 2022 27 commits
-
-
Jakub Kicinski authored
Vladimir Oltean says: ==================== Count tc-taprio window drops in enetc driver This series includes a patch from Po Liu (no longer with NXP) which counts frames dropped by the tc-taprio offload in ethtool -S and in ndo_get_stats64. It also contains a preparation patch from myself. ==================== Link: https://lore.kernel.org/r/20220510163615.6096-1-vladimir.oltean@nxp.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Po Liu authored
The enetc scheduler for IEEE 802.1Qbv has 2 options (depending on PTGCR[TG_DROP_DISABLE]) when we attempt to send an oversized packet which will never fit in its allotted time slot for its traffic class: either block the entire port due to head-of-line blocking, or drop the packet and set a bit in the writeback format of the transmit buffer descriptor, allowing other packets to be sent. We obviously choose the second option in the driver, but we do not detect the drop condition, so from the perspective of the network stack, the packet is sent and no error counter is incremented. This change checks the writeback of the TX BD when tc-taprio is enabled, and increments a specific ethtool statistics counter and a generic "tx_dropped" counter in ndo_get_stats64. Signed-off-by:
Po Liu <Po.Liu@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
Future work in this driver would like to look at priv->active_offloads & ENETC_F_QBV to determine whether a tc-taprio qdisc offload was installed, but this does not produce the intended effect. All the other flags in priv->active_offloads are managed dynamically, except ENETC_F_QBV which is set statically based on the probed SI capability. This change makes priv->active_offloads & ENETC_F_QBV really track the presence of a tc-taprio schedule on the port. Some existing users, like the enetc_sched_speed_set() call from phylink_mac_link_up(), are best kept using the old logic: the tc-taprio offload does not re-trigger another link mode resolve, so the scheduler needs to be functional from the get go, as long as Qbv is supported at all on the port. So to preserve functionality there, look at the static station interface capability from pf->si->hw_features instead. Signed-off-by:
-
Jakub Kicinski authored
Robert Hancock says: ==================== MACB NAPI improvements Simplify the logic in the Cadence MACB/GEM driver for determining when to reschedule NAPI processing, and update it to use NAPI for the TX path as well as the RX path. Changes since v1: Changed to use separate TX and RX NAPI instances and poll functions to avoid unnecessary checks of the other ring (TX/RX) states during polling and to use budget handling for both RX and TX. Fixed locking to protect against concurrent access to TX ring on TX transmit and TX poll paths. ==================== Link: https://lore.kernel.org/r/20220509194635.3094080-1-robert.hancock@calian.comSigned-off-by:
-
Robert Hancock authored
This driver was using the TX IRQ handler to perform all TX completion tasks. Under heavy TX network load, this can cause significant irqs-off latencies (found to be in the hundreds of microseconds using ftrace). This can cause other issues, such as overrunning serial UART FIFOs when using high baud rates with limited UART FIFO sizes. Switch to using a NAPI poll handler to perform the TX completion work to get this out of hard IRQ context and avoid the IRQ latency impact. A separate NAPI instance is used for TX and RX to avoid checking the other ring's state unnecessarily when doing the poll, and so that the NAPI budget handling can work for both TX and RX packets. A new per-queue tx_ptr_lock spinlock has been added to avoid using the main device lock (with IRQs needing to be disabled) across the entire TX mapping operation, and also to protect the TX queue pointers from concurrent access between the TX start and TX poll operations. The TX Used Bit Read interrupt (TXUBR) handling also needs to be moved into the TX NAPI poll handler to maintain the proper order of operations. A flag is used to notify the poll handler that a UBR condition needs to be handled. The macb_tx_restart handler has had some locking added for global register access, since this could now potentially happen concurrently on different queues. Signed-off-by:
Robert Hancock <robert.hancock@calian.com> Signed-off-by:
-
Robert Hancock authored
Previously the macb_poll method was checking the RSR register after completing its RX receive work to see if additional packets had been received since IRQs were disabled, since this controller does not maintain the pending IRQ status across IRQ disable. It also had to double-check the register after re-enabling IRQs to detect if packets were received after the first check but before IRQs were enabled. Using the RSR register for this purpose is problematic since it reflects the global device state rather than the per-queue state, so if packets are being received on multiple queues it may end up retriggering receive on a queue where the packets did not actually arrive and not on the one where they did arrive. This will also cause problems with an upcoming change to use NAPI for the TX path where use of multiple queues is more likely. Add a macb_rx_pending function to check the RX ring to see if more packets have arrived in the queue, and use that to check if NAPI should be rescheduled rather than the RSR register. By doing this, we can just ignore the global RSR register entirely, and thus save some extra device register accesses at the same time. This also makes the previous first check for pending packets rather redundant, since it would be checking the RX ring state which was just checked in the receive work function. Therefore we can get rid of it and just check after enabling interrupts whether packets are already pending. Signed-off-by:
-
Vladimir Oltean authored
Switches using the Lynx PCS driver support 1000base-X optical SFP modules. Accept this interface type on a port. Signed-off-by:
-
Vladimir Oltean authored
The host interfaces $h1 and $h2 don't have to be switchdev interfaces, but due to the fact that we pass $tcflags which may have the value of "skip_sw", we force $h2 to offload a drop rule for dst_ip, something which it may not be able to do. The selftest only wants to verify the hit count of this rule as a means of figuring out whether the packet was received, so remove the $tcflags for it and let it be done in software. Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Tested-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== 1GbE Intel Wired LAN Driver Updates 2022-05-10 This series contains updates to igc driver only. Sasha cleans up the code by removing an unused function and removing an enum for PHY type as there is only one PHY. The return type for igc_check_downshift() is changed to void as it always returns success. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: igc: Change type of the 'igc_check_downshift' method igc: Remove unused phy_type enum igc: Remove igc_set_spd_dplx method ==================== Link: https://lore.kernel.org/r/20220510210656.2168393-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Jakub Kicinski authored
Looks like all the changes to this driver had been tree-wide refactoring since git era begun. The driver is using virt_to_bus() we should make it use more modern DMA APIs but since it's unlikely to be getting any use these days delete it instead. We can always revert to bring it back. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Looks like all the changes to this driver had been tree-wide refactoring since git era begun. The driver is using virt_to_bus() we should make it use more modern DMA APIs but since it's unlikely to be getting any use these days delete it instead. We can always revert to bring it back. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net: CONFIG_DEBUG_NET and friends This patch series is inspired by some syzbot reports hinting that skb transport_header might be not set in places we expect it being set. Add a new CONFIG_DEBUG_NET option and DEBUG_NET_WARN_ON_ONCE() helper, so that we can start adding more sanity checks in the future. Replace two BUG() in skb_checksum_help() with less risky code. v2: make first patch compile on more arches/compilers add the 5th patch to add more debugging in skb_checksum_help() ==================== Signed-off-by: -
Eric Dumazet authored
This is a followup of previous patch. Dumping the stack trace is a good start, but printing basic skb information is probably better. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
I have a syzbot report that managed to get a crash in skb_checksum_help() If syzbot can trigger these BUG(), it makes sense to replace them with more friendly WARN_ON_ONCE() since skb_checksum_help() can instead return an error code. Note that syzbot will still crash there, until real bug is fixed. Signed-off-by:
-
Eric Dumazet authored
Make sure skb_transport_header() and skb_transport_offset() uses are not fooled if the transport header has not been set. This change will likely expose existing bugs in linux networking stacks. Signed-off-by:
-
Eric Dumazet authored
This config option enables network debugging checks. This patch adds DEBUG_NET_WARN_ON_ONCE(cond) Note that this is not a replacement for WARN_ON_ONCE(cond) as (cond) is not evaluated if CONFIG_DEBUG_NET is not set. Signed-off-by:
-
Eric Dumazet authored
Remove from include/linux/netdevice.h helpers that send debug/info/warnings to syslog. We plan adding more helpers in following patches. v2: added two includes, and 'struct net_device' forward declaration to avoid compile errors (kernel bots) Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2022-05-09 1) Gavin Li, adds exit route from waiting for FW init on device boot and increases FW init timeout on health recovery flow 2) Support 4 ports HCAs LAG mode Mark Bloch Says: ================ This series adds to mlx5 drivers support for 4 ports HCAs. Starting with ConnectX-7 HCAs with 4 ports are possible. As most driver parts aren't affected by such configuration most driver code is unchanged. Specially the only affected areas are: - Lag - Devcom - Merged E-Switch - Single FDB E-Switch Lag was chosen to be converted first. Creating hardware LAG when all 4 ports are added to the same bond device. Devom, merge E-Switch and single FDB E-Switch, are marked as supporting only 2 ports HCAs and future patches will add support for 4 ports HCAs. In order to activate the hardware lag a user can execute the: ip link add bond0 type bond ip link set bond0 type bond miimon 100 mode 2 ip link set eth2 master bond0 ip link set eth3 master bond0 ip link set eth4 master bond0 ip link set eth5 master bond0 Where eth2, eth3, eth4 and eth5 are the PFs of the same HCA. ================ ==================== Signed-off-by: -
Jakub Kicinski authored
Yuiko Oshino says: ==================== net: phy: add comments for LAN8742 phy support Add comments for 0xfffffff2 phy ID mask for the LAN8742 and the LAN88xx, explaining that they can coexist and allow future hardware revisions. Also add one missing tab in smsc.c. ==================== Link: https://lore.kernel.org/r/20220509185804.7147-1-yuiko.oshino@microchip.comSigned-off-by:
-
Yuiko Oshino authored
add comments for the LAN8742 phy ID mask in the previous patch. add one missing tab in the LAN8742 phy ID line. Signed-off-by:
Yuiko Oshino <yuiko.oshino@microchip.com> Signed-off-by:
-
Yuiko Oshino authored
add comments for the updated LAN88xx phy ID mask in the previous patch. Signed-off-by:
-
Chris Packham authored
Convert the marvell,orion-mdio binding to JSON schema. Signed-off-by:
Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220505210621.3637268-1-chris.packham@alliedtelesis.co.nzSigned-off-by:
-
Jakub Kicinski authored
Jakub Kicinski says: ==================== docs: document some aspects of struct sk_buff This small set creates a place to render sk_buff documentation, documents one random thing (data-only skbs) and converts the big checksum comment to kdoc. ==================== Link: https://lore.kernel.org/r/20220323233715.2104106-1-kuba@kernel.org/ Link: https://lore.kernel.org/r/20220324231312.2241166-1-kuba@kernel.org/ Link: https://lore.kernel.org/r/20220509160456.1058940-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Long time ago Tom added a giant comment to skbuff.h explaining checksums. Now that we have a place in Documentation for skbuff docs we should render it. Sprinkle some markup while at it. Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
Jakub Kicinski authored
The comment about shinfo->dataref split is really unhelpful, at least to me. Rewrite it and render it to skb documentation. Reviewed-by:
-
Jakub Kicinski authored
Add basic skb documentation. It's mostly an intro to the subsequent patches - it would looks strange if we documented advanced topics without covering the basics in any way. Reviewed-by:
-
Jakub Kicinski authored
Commit c526fd8f ("net: inline dev_queue_xmit()") exported __dev_queue_xmit(), now it's being rendered in html docs, triggering: Documentation/networking/kapi:92: net/core/dev.c:4101: WARNING: Missing matching underline for section title overline. Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Link: https://lore.kernel.org/linux-next/20220503073420.6d3f135d@canb.auug.org.au/ Fixes: c526fd8f ("net: inline dev_queue_xmit()") Link: https://lore.kernel.org/r/20220509170412.1069190-1-kuba@kernel.orgSigned-off-by:
-
- 10 May, 2022 8 commits
-
-
Jakub Kicinski authored
Martin Habets says: ==================== Move Siena into a separate subdirectory The Siena NICs (SFN5000 and SFN6000 series) went EOL in November 2021. Most of these adapters have been remove from our test labs, and testing has been reduced to a minimum. This patch series creates a separate kernel module for the Siena architecture, analogous to what was done for Falcon some years ago. This reduces our maintenance for the sfc.ko module, and allows us to enhance the EF10 and EF100 drivers without the risk of breaking Siena NICs. After this series further enhancements are needed to differentiate the new kernel module from sfc.ko, and the Siena code can be removed from sfc.ko. Thes will be posted as a small follow-up series. The Siena module is not built by default, but can be enabled using Kconfig option SFC_SIENA. This will create module sfc-siena.ko. Patches Patches 1-3 establish the code base for the Siena driver. Patches 4-10 ensure the allyesconfig build succeeds. Patch 11 adds the basic Siena module. I do not expect patch 1 through 3 to be reviewed, they are FYI only. No checkpatch issues were resolved as part of these, but they were fixed in the subsequent patches. Testing Various build tests were done such as allyesconfig, W=1 and sparse. The new sfc-siena.ko and sfc.ko modules were tested on a machine with both these NICs in them, and several tests were run on both drivers. ==================== Link: https://lore.kernel.org/r/165211018297.5289.9658523545298485394.stgit@palantir17.mph.netSigned-off-by:
-
Martin Habets authored
Make the (un)load message more specific to differentiate it from the sfc.ko messages. Signed-off-by:
Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by:
-
Martin Habets authored
The implementation of each is quite short. This means sriov.c is not needed any more. Signed-off-by:
-
Martin Habets authored
For siena use efx_siena_ as the function prefix. efx_nic_update_stats_atomic is only used in efx_common.c, so move it there. efx_nic_copy_stats is not used in Siena, so it is removed. Signed-off-by:
-
Martin Habets authored
For siena use efx_siena_ as the function prefix. Several functions are not used in Siena, so they are removed. Signed-off-by:
-
Martin Habets authored
For siena use efx_siena_ as the function prefix. This patch covers selftest.h, ptp.h, net_driver.h and ethtool_common.h. efx_ethtool_fill_self_tests() can become static. Some functions in ptp.c can also become static. Rename loopback_mode in net_driver.h. Signed-off-by:
-
Martin Habets authored
For siena use efx_siena_ as the function prefix. Several functions are not used in Siena, so they are removed. Use a Siena specific variable name for module parameter efx_separate_tx_channels. Move efx_fini_tx_queue() to avoid a forward declaration of efx_dequeue_buffer(). Signed-off-by:
-
Martin Habets authored
When building with allyesconfig there are many identical symbol names. For siena use efx_siena_ as the function and variable prefix to avoid build errors. efx_mtd_remove_partition can become static as it is no longer called from other files. efx_ticks_to_usecs and efx_xmit_done_single are not used in Siena, so they are removed. Several functions are only used inside efx_channels.c for Siena so they can become static. Signed-off-by:
-
