- 26 Apr, 2023 40 commits
-
-
Shengyu Qu authored
The AXP15060 is a PMIC chip produced by X-Powers, and could be connected via an I2C bus. Describe the regmap and the MFD bits, along with the registers exposed via I2C. Eventually advertise the device using a new compatible string and add support for power off the system. The driver would disable PEK function if IRQ is not configured in device tree, since some boards (For example, Starfive Visionfive 2) didn't connect IRQ line of PMIC to SOC. GPIO function isn't enabled in this commit, since its configuration operation is different from any existing AXP PMICs and needs logic modification on existing driver. GPIO support might come in later patches. Signed-off-by:
Shengyu Qu <wiagn233@outlook.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/TY3P286MB261162D57695AC8164ED50E298609@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM
-
Martin Botka authored
The X-Powers AXP313a is a PMIC used on some devices with the Allwinner H616 or H313 SoC. According to the datasheet, the DC/DC converter PWM frequency is fixed (to 3 MHz), so disallow the property that lets us set this frequency for the other PMICs. Signed-off-by:
Martin Botka <martin.botka@somainline.org> Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230401001850.4988-2-andre.przywara@arm.com (cherry picked from commit 2a9e8a1a7c4caadf690e5a77fe4162c5edab4a9c) Signed-off-by:
Lee Jones <lee@kernel.org>
-
Dan Carpenter authored
These error paths need to call mutex_unlock(&priv->lock) before returning. The lock is taken in rz_mtu3_lock_if_counter_is_valid(). Fixes: 25d21447d896 ("counter: Add Renesas RZ/G2L MTU3a counter driver") Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Acked-by:
William Breathitt Gray <william.gray@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/7b535d6b-6031-493a-84f6-82842089e637@kili.mountain
-
Benjamin Bara authored
Document that the da9063 only provides under- *and* over-voltage monitoring in one, and therefore requires both to be configured with the same severity and value. Add an example for clarification. Signed-off-by:
Benjamin Bara <benjamin.bara@skidata.com> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230403-da9063-disable-unused-v3-3-cc4dc698864c@skidata.com
-
Patrick Delaunay authored
Remove double blank line. Signed-off-by:
Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230417181342.v2.1.I483a676579cc7e3ac07e1db649091553743fecc8@changeid
-
Marijn Suijten authored
Update the examples to reflect a future requirement for the generic `channel` node name on ADC channel nodes, while conveying the board name of the channel in a label instead. Signed-off-by:
Marijn Suijten <marijn.suijten@somainline.org> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230410202917.247666-5-marijn.suijten@somainline.org
-
Jacky Huang authored
Add Nuvoton ma35d1 system registers compatible. Signed-off-by:
Jacky Huang <ychuang3@nuvoton.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230328021912.177301-6-ychuang570808@gmail.com
-
Biju Das authored
Add the MAINTAINERS entries for the Renesas RZ/G2L MTU3a counter driver. Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330111632.169434-6-biju.das.jz@bp.renesas.com
-
Biju Das authored
Add RZ/G2L MTU3a counter driver. This IP supports the following phase counting modes on MTU1 and MTU2 channels 1) 16-bit phase counting modes on MTU1 and MTU2 channels. 2) 32-bit phase counting mode by cascading MTU1 and MTU2 channels. This patch adds 3 counter value channels. count0: 16-bit phase counter value channel on MTU1 count1: 16-bit phase counter value channel on MTU2 count2: 32-bit phase counter value channel by cascading MTU1 and MTU2 channels. The external input phase clock pin for the counter value channels are as follows: count0: "MTCLKA-MTCLKB" count1: "MTCLKA-MTCLKB" or "MTCLKC-MTCLKD" count2: "MTCLKA-MTCLKB" or "MTCLKC-MTCLKD" Use the sysfs variable "external_input_phase_clock_select" to select the external input phase clock pin and "cascade_counts_enable" to enable/ disable cascading of channels. Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
William Breathitt Gray <william.gray@linaro.org> Acked-by:
William Breathitt Gray <william.gray@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330111632.169434-5-biju.das.jz@bp.renesas.com
-
Biju Das authored
Documentation: ABI: sysfs-bus-counter: add cascade_counts_enable and external_input_phase_clock_select This commit adds cascade_counts_enable and external_input_phase_ clock_select items to counter ABI file. (e.g. for Renesas MTU3 hardware used for phase counting). Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
William Breathitt Gray <william.gray@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330111632.169434-4-biju.das.jz@bp.renesas.com
-
Biju Das authored
The RZ/G2L multi-function timer pulse unit 3 (MTU3a) is embedded in the Renesas RZ/G2L family SoCs. It consists of eight 16-bit timer channels and one 32-bit timer channel. It supports the following functions - Counter - Timer - PWM The 8/16/32 bit registers are mixed in each channel. Add MTU3a core driver for RZ/G2L SoC. The core driver shares the clk and channel register access for the other child devices like Counter, PWM and Clock event. Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330111632.169434-3-biju.das.jz@bp.renesas.com
-
Biju Das authored
The RZ/G2L multi-function timer pulse unit 3 (MTU3a) is embedded in the Renesas RZ/G2L family SoC's. It consists of eight 16-bit timer channels and one 32-bit timer channel. It supports the following functions - Counter - Timer - PWM Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330111632.169434-2-biju.das.jz@bp.renesas.com
-
Uwe Kleine-König authored
This commit reapplies commit 601e6d48 ("mfd: rsmu_i2c: Convert to i2c's .probe_new()") which was accidently reverted by commit 1b3b1d6c27cc ("mfd: rsmu: Support 32-bit address space"). Without this change the driver fails to build in combination with commit 03c835f4 ("i2c: Switch .probe() to not take an id parameter") which is contained in v6.3-rc2. Fixes: 1b3b1d6c27cc ("mfd: rsmu: Support 32-bit address space") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230331070344.czphnnmvu2ojzo5l@pengutronix.de
-
Jarkko Nikula authored
Add Intel Meteor Lake PCH-S also called as Meteor Point-S LPSS PCI IDs. Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330132618.4108665-1-jarkko.nikula@linux.intel.com
-
Qiang Ning authored
When dln2_setup_rx_urbs() in dln2_probe() fails, error out_free forgets to call usb_put_dev() to decrease the refcount of dln2->usb_dev. Fix this by adding usb_put_dev() in the error handling code of dln2_probe(). Signed-off-by:
Qiang Ning <qning0106@126.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230330024353.4503-1-qning0106@126.com
-
Hans de Goede authored
Register AXP288_POWER_REASON is writable and needs to be written to reset the reset- / power-on-reason bits. Add it to the axp288 writable-ranges so that the extcon-axp288 driver can properly clear the reset- / power-on-reason bits. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230329205544.1051393-1-hdegoede@redhat.com
-
Krzysztof Kozlowski authored
The syntax to disallow x-powers,drive-vbus-en, x-powers,self-working-mode and x-powers,master-mode for certain variants can be made simpler. Also this produces much nicer warning message when the condition hits wrong DTS. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by:
Chen-Yu Tsai <wens@csie.org> Reviewed-by:
Andre Przywara <andre.przywara@arm.com> Tested-by:
Andre Przywara <andre.przywara@arm.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230325114353.50293-1-krzysztof.kozlowski@linaro.org
-
Min Li authored
We used to assume 0x2010xxxx address. Now that we need to access 0x2011xxxx address, we need to support read/write the whole 32-bit address space. Also defined RSMU_MAX_WRITE_COUNT and RSMU_MAX_READ_COUNT for readability Signed-off-by:
Min Li <min.li.xe@renesas.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/MW5PR03MB693295AF31ABCAF6AE52EE74A08B9@MW5PR03MB6932.namprd03.prod.outlook.com
-
Johan Hovold authored
Add an 'nvram' pattern property and a reference to the corresponding SDAM DT schema. Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230320135710.1989-4-johan+linaro@kernel.org
-
Charles Keepax authored
This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as a module. Fixes: 3f65555c ("mfd: arizona: Split of_match table into I2C and SPI versions") Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230323134138.834369-1-ckeepax@opensource.cirrus.com
-
Rob Herring authored
Cleanup bindings dropping unneeded quotes. Once all these are fixed, checking for this can be enabled in yamllint. Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230322173519.3971434-1-robh@kernel.org
-
Colin Foster authored
Ocelot chips (VSC7511, VSC7512, VSC7513, VSC7514) don't support bulk read operations over SPI. Many SPI buses have hardware that can optimize consecutive reads. Essentially an address is written to the chip, and if the SPI controller continues to toggle the clock, subsequent register values are reported. This can lead to significant optimizations, because the time between "address is written to the chip" and "chip starts to report data" can often take a fixed amount of time. When support for Ocelot chips were added in commit f3e89362 ("mfd: ocelot: Add support for the vsc7512 chip via spi") it was believed that this optimization was supported. However it is not. Most register transactions with the Ocelot chips are not done in bulk, so this bug could go unnoticed. The one scenario where bulk register operations _are_ performed is when polling port statistics counters, which was added in commit d87b1c08 ("net: mscc: ocelot: use bulk reads for stats"). Things get slightly more complicated here... A bug was introduced in commit d4c36765 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset") that broke the optimization of bulk reads. This means that when Ethernet support for the VSC7512 chip was added in commit 3d7316ac ("net: dsa: ocelot: add external ocelot switch control") things were actually working "as expected". The bulk read opmtimization was discovered, and fixed in commit 6acc72a4 ("net: mscc: ocelot: fix stats region batching") and the timing optimizations for SPI were noticed. A bulk read went from ~14ms to ~2ms. But this timing improvement came at the cost of every register reading zero due the fact that bulk reads don't work. The read timings increase back to 13-14ms, but that's a price worth paying in order to receive valid data. This is verified in a DSA setup (cpsw-new switch tied to port 0 on the VSC7512, after having been running overnight) Rx Octets: 16222055 # Counters from CPSW switch Tx Octets: 12034702 Net Octets: 28256757 p00_rx_octets: 12034702 # Counters from Ocelot switch p00_rx_frames_below_65_octets: 0 p00_rx_frames_65_to_127_octets: 88188 p00_rx_frames_128_to_255_octets: 13 p00_rx_frames_256_to_511_octets: 0 p00_rx_frames_512_to_1023_octets: 0 p00_rx_frames_over_1526_octets: 3306 p00_tx_octets: 16222055 Fixes: f3e89362 ("mfd: ocelot: Add support for the vsc7512 chip via spi") Signed-off-by:
Colin Foster <colin.foster@in-advantage.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230322141130.2531256-1-colin.foster@in-advantage.com
-
Tom Rix authored
Clang with W=1 reports: drivers/mfd/omap-usb-tll.c:128:18: error: unused function 'usbtll_readb' [-Werror,-Wunused-function] static inline u8 usbtll_readb(void __iomem *base, u32 reg) ^ This function is not used so remove it. Signed-off-by:
Tom Rix <trix@redhat.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230322125803.2570968-1-trix@redhat.com
-
Tom Rix authored
Clang with W=1 reports: drivers/mfd/twl-core.c:654:30: error: unused function 'add_child' [-Werror,-Wunused-function] static inline struct device *add_child(unsigned mod_no, const char *name, ^ add_numbered_child() and its only caller add_child() are not used, so remove them. Signed-off-by:
Tom Rix <trix@redhat.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230322115838.2569414-1-trix@redhat.com
-
Bartosz Golaszewski authored
PMM8654au is the SPMI PMIC variant used on sa8775p-ride. Add a compatible for it. Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230314183043.619997-5-brgl@bgdev.pl
-
André Apitzsch authored
This patch adds missing MODULE_DEVICE_TABLE definition which generates correct modalias for automatic loading of this driver when it is built as a module. Signed-off-by:
André Apitzsch <git@apitzsch.eu> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230319124153.35294-1-git@apitzsch.eu
-
Konrad Dybcio authored
Add a compatible for PM2250, commonly found with QCM2290. Signed-off-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230315183819.3563704-1-konrad.dybcio@linaro.org
-
Geert Uytterhoeven authored
There is no need to cast a "void *" to a different type of pointer. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/ae84c1751e79cb49ab584557f4ecd835a8493d7c.1678704562.git.geert+renesas@glider.be
-
Krzysztof Kozlowski authored
The driver can match only via the DT table so the table should be always used and the of_match_ptr does not have any sense (this also allows ACPI matching via PRP0001, even though it might not be relevant here). drivers/mfd/atc260x-i2c.c:44:34: error: ‘atc260x_i2c_of_match’ defined but not used [-Werror=unused-const-variable=] Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230311111629.251830-2-krzysztof.kozlowski@linaro.org
-
Krzysztof Kozlowski authored
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/mfd/atmel-smc.c:326:34: error: ‘atmel_smc_ids’ defined but not used [-Werror=unused-const-variable=] Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230311111629.251830-1-krzysztof.kozlowski@linaro.org
-
Rob Herring authored
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. Convert reading boolean properties to to of_property_read_bool(). Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230310144712.1543449-1-robh@kernel.org
-
Rob Herring authored
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230310144712.1543379-1-robh@kernel.org
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230308194307.374789-1-nick.alcock@oracle.com
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Lee Jones <lee@kernel.org>
-