- 27 Jan, 2021 26 commits
-
-
Daniel W. S. Almeida authored
Add media controller support when CONFIG_MEDIA_CONTROLLER_DVB is set so that, in the future, a test sequence in v4l-utils can be written without having to know which /dev/fooX device should be used. [mchehab: avoided usage of C99 comments] Signed-off-by:
Daniel W. S. Almeida <dwlsalmeida@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Tian Tao authored
Fixes coccicheck warning: drivers/media/test-drivers/vidtv/vidtv_psi.c:509:10-17: WARNING opportunity for kmemdup Signed-off-by:
Tian Tao <tiantao6@hisilicon.com> Signed-off-by:
-
Daniel W. S. Almeida authored
Commit 3d1387b3 ("media: vidtv: fix some warnings") replaced the unused flexible array member at the end of struct vidtv_mpeg_ts with a pointer. This broke the 188-byte alignment since the struct no longer was 4 bytes in size. Fix this by removing this field entirely. Fixes: 3d1387b3 ("media: vidtv: fix some warnings") Signed-off-by:
-
Daniel W. S. Almeida authored
The PMT write function was refactored and this broke the CRC computation. Fix it. Fixes: db9569f6 ("media: vidtv: cleanup PMT write table function") Signed-off-by:
-
Hans Verkuil authored
By adding this cast '(__force __le16)' this sparse warning is fixed: drivers/media/i2c/ov02a10.c:391:19: warning: cast to restricted __le16 Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
Fix two smatch warnings: drivers/staging/media/atomisp//pci/ia_css_firmware.h:52:29: warning: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration drivers/staging/media/atomisp//pci/ia_css_control.h:49:24: warning: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration Add '#include <linux/device.h>' to ia_css_firmware.h so struct device is defined. ia_css_control.h includes ia_css_firmware.h, so it is sufficient to just modify ia_css_firmware.h. Signed-off-by:
-
Hans Verkuil authored
Fixes two smatch warnings: drivers/media/dvb-frontends/af9033.c:128 af9033_init() warn: missing error code 'ret' drivers/media/dvb-frontends/af9033.c:855 af9033_read_snr() warn: missing error code 'ret' Set error codes correctly. Signed-off-by:
-
Hans Verkuil authored
Fixes this smatch warning: drivers/media/dvb-frontends/rtl2832.c:702 rtl2832_read_status() warn: missing error code 'ret' 'ret' is indeed not set, so set it to -EINVAL so a proper error code is returned. Signed-off-by:
-
Hans Verkuil authored
Fixes this smatch warning: drivers/media/usb/dvb-usb-v2/rtl28xxu.c:1040 rtl2832u_frontend_attach() warn: missing error code 'ret' It is actually a bogus warning since in this particular case ret isn't meant to be set. But by reworking the code a bit the code is actually a lot more understandable and it fixes this warning. Signed-off-by:
-
Hans Verkuil authored
Fix this smatch warning: drivers/media/pci/ivtv/ivtv-driver.c:900 ivtv_setup_pci() warn: 'itv->base_addr' not released on lines: 876. One error path didn't release the memory regions. Signed-off-by:
-
Hans Verkuil authored
Fixes this smatch warning: drivers/media/platform/sti/hva/hva-hw.c:453 hva_hw_runtime_resume() warn: 'hva->clk' not released on lines: 450. Call clk_disable_unprepare() when clk_set_rate() fails. Signed-off-by:
-
Hans Verkuil authored
Fixes this smatch warning: drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:829 c8sectpfe_probe() warn: missing error code 'ret' Set ret to -EINVAL if the reset gpio was not found. Signed-off-by:
-
Hans Verkuil authored
Fix two typos: dvdd -> dovdd and dvdd -> avdd Both clearly copy-and-paste mistakes. Fixes this smatch warning: drivers/media/i2c/ov8865.c:2852 ov8865_probe() warn: passing zero to 'PTR_ERR' Signed-off-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Hans Verkuil authored
Fixes this smatch warning: drivers/media/tuners/it913x.c:65 it913x_init() warn: missing error code 'ret' Set ret to -EINVAL if the clock identifier was invalid. Signed-off-by:
-
Hans Verkuil authored
Fixes this smatch warning: drivers/media/platform/davinci/vpbe.c:632 vpbe_initialize() warn: missing error code 'ret' The function returns 'ret', but instead 'err' was set to -ENOMEM. Signed-off-by:
-
Hans Verkuil authored
Fix this smatch warning: drivers/media/platform/meson/ge2d/ge2d.c:991 ge2d_probe() warn: missing error code 'ret' when video_device_alloc() returns NULL. Signed-off-by:
-
Hans Verkuil authored
If a menu has more than 64 items, then don't check menu_skip_mask for items 65 and up. Signed-off-by:
-
Hans Verkuil authored
Fix this compiler warning on i686: In file included from include/linux/printk.h:409, from include/linux/kernel.h:16, from drivers/staging/media/atomisp/pci/hmm/hmm.c:23: drivers/staging/media/atomisp/pci/hmm/hmm.c: In function 'hmm_alloc': drivers/staging/media/atomisp/pci/hmm/hmm.c:272:3: warning: format '%ld' expects argument of type 'long int', but argument 6 has type 'size_t' {aka 'unsigned int'} [-Wformat=] 272 | "%s: pages: 0x%08x (%ld bytes), type: %d from highmem %d, user ptr %p, cached %d\n", | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Use %zu instead of %ld. Signed-off-by: -
Malcolm Priestley authored
This function is not necessary and largely a remnant of dvb-usb workaround and is now controlled by dvb-usb-v2. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Malcolm Priestley authored
lme2510_int_read is not atomically called so use GFP_KERNEL for usb_alloc_urb and usb_submit_urb which is the first in the chain of interrupt submissions. Signed-off-by:
-
Joe Perches authored
There's a comma used instead of a semicolon that causes multiple statements to be executed after an if instead of just the intended single statement. Replace the comma with a semicolon. Fixes: 15e1ce33 ("[media] lmedm04: Fix usb_submit_urb BOGUS urb xfer, pipe 1 != type 3 in interrupt urb") Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Sean Young authored
prescaler larger than 8 would mean the carrier is at most 152Hz, which does not make sense for IR carriers. Reported-by: syzbot+6d31bf169a8265204b8d@syzkaller.appspotmail.com Signed-off-by:
-
Samuel Holland authored
To save power, gate/reset the hardware block while the system is asleep or powered off. Acked-by:
Maxime Ripard <mripard@kernel.org> Signed-off-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
-
Samuel Holland authored
In preparation for adding suspend/resume hooks, factor out the hardware initialization from the driver probe/remove functions. The timeout programmed during init is taken from the `struct rc_dev` so it is maintained across an exit/init cycle. This resolves some trivial issues with the probe function: throwing away the error from clk_prepare_enable and using the wrong type for the temporary register value. It also fixes the order of the remove function to unregister the RC device before turning off the hardware. This prevents userspace from triggering register writes (via LIRC_SET_REC_TIMEOUT) while the hardware is disabled. Acked-by:
-
Samuel Holland authored
Only one register, SUNXI_IR_CIR_REG, is accessed from outside the interrupt handler, and that register is not accessed from inside it. As there is no overlap between different contexts, no lock is needed. Acked-by:
-
Samuel Holland authored
The register writes during driver removal occur after the device is already put back in reset, so they never had any effect. Acked-by:
-
- 26 Jan, 2021 14 commits
-
-
Daniel Scally authored
Currently on platforms designed for Windows, connections between CIO2 and sensors are not properly defined in DSDT. This patch extends the ipu3-cio2 driver to compensate by building software_node connections, parsing the connection properties from the sensor's SSDB buffer. [Sakari Ailus: Make cio2_bridge_init static inline to a fix compiler warning, wrapped a bunch of long lines.] Suggested-by:
Jordan Hand <jorhand@linux.microsoft.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by:
Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by:
Daniel Scally <djrscally@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Daniel Scally authored
V4L2 fwnode bus types are enumerated in v4l2-fwnode.c, meaning they aren't available to the rest of the kernel. Move the enum to the corresponding header so that I can use the label to refer to those values. Suggested-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
-
Daniel Scally authored
To ensure we handle situations in which multiple sensors of the same model (and therefore _HID) are present in a system, we need to be able to iterate over devices matching a known _HID but unknown _UID and _HRV - add acpi_dev_get_next_match_dev() to accommodate that possibility and change acpi_dev_get_first_match_dev() to simply call the new function with a NULL starting point. Add an iterator macro for convenience. Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Daniel Scally authored
Where the fwnode graph is comprised of software_nodes, these will be assigned as the secondary to dev->fwnode. Check the v4l2_subdev's fwnode for a secondary and attempt to match against it during match_fwnode() to accommodate that possibility. Reviewed-by:
-
Daniel Scally authored
ipu3-cio2 driver needs extending with multiple files; rename the main source file and specify the renamed file in Makefile to accommodate that. Suggested-by:
-
Daniel Scally authored
Development for the ipu3-cio2 driver is taking place in media_tree, but there's no T: entry in MAINTAINERS to denote that - rectify that oversight Reviewed-by:
-
Daniel Scally authored
Use the software_node_unregister_nodes() helper function to unwind this array in a cleaner way. Acked-by:
Petr Mladek <pmladek@suse.com> Reviewed-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Suggested-by:
-
Heikki Krogerus authored
This implements the remaining .graph_*() callbacks in the fwnode operations structure for the software nodes. That makes the fwnode_graph_*() functions available in the drivers also when software nodes are used. The implementation tries to mimic the "OF graph" as much as possible, but there is no support for the "reg" device property. The ports will need to have the index in their name which starts with "port@" (for example "port@0", "port@1", ...) and endpoints will use the index of the software node that is given to them during creation. The port nodes can also be grouped under a specially named "ports" subnode, just like in DT, if necessary. The remote-endpoints are reference properties under the endpoint nodes that are named "remote-endpoint". Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Co-developed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
-
Daniel Scally authored
OF, ACPI and software_nodes all implement graphs including nodes for ports and endpoints. These are all intended to be named with a common schema, as "port@n" and "endpoint@n" where n is an unsigned int representing the index of the node. To ensure commonality across the subsystems, provide a set of macros to define the format. Suggested-by:
-
Daniel Scally authored
To maintain consistency with software_node_unregister_nodes(), reverse the order in which the software_node_unregister_node_group() function unregisters nodes. Reported-by:
-
Daniel Scally authored
Registering software_nodes with the .parent member set to point to a currently unregistered software_node has the potential for problems, so enforce parent -> child ordering in arrays passed in to software_node_register_nodes(). Software nodes that are children of another software node should be unregistered before their parent. To allow easy unregistering of an array of software_nodes ordered parent to child, reverse the order in which software_node_unregister_nodes() unregisters software_nodes. Suggested-by:
-
Daniel Scally authored
This function is used to find fwnode endpoints against a device. In some instances those endpoints are software nodes which are children of fwnode->secondary. Add support to fwnode_graph_get_endpoint_by_id() to find those endpoints by recursively calling itself passing the ptr to fwnode->secondary in the event no endpoint is found for the primary. Reviewed-by:
-
Daniel Scally authored
Some types of fwnode_handle do not implement the device_is_available() check, such as those created by software_nodes. There isn't really a meaningful way to check for the availability of a device that doesn't actually exist, so if the check isn't implemented just assume that the "device" is present. Suggested-by:
-
Andy Shevchenko authored
Add headers that ipu3-cio2.h is direct user of. Signed-off-by:
-
