- 21 Dec, 2012 40 commits
-
-
Jesper Juhl authored
At the 'err_request_irq' label, rc_unregister_device(rcdev) frees its argument. So when we fall through to the 'err_gpio_request' label further down and call rc_free_device(rcdev) then that's a double free. Fix that by moving 'rcdev = NULL' from after the call to rc_free_device() to after rc_unregister_device(). That fixes the problem since rc_free_device() just does nothing if passed NULL and there's no further use of 'rcdev' after the call to rc_free_device() so it's not needed there. Signed-off-by:
Jesper Juhl <jj@chaosbits.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
The two new tests don't set the returned value. Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: -
Michael Krufky authored
display an error message if either tuner_i2c_addr or demod_i2c_addr are not specified in the tda10071_config structure Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Andy Shevchenko authored
Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Andy Shevchenko authored
Signed-off-by:
-
Andy Shevchenko authored
Signed-off-by:
-
Wei Yongjun authored
The variable 'output_index' is initialized but never used otherwise, so remove the unused variable. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Prabhakar Lad <prabhakar.lad@ti.com> Signed-off-by:
-
Wei Yongjun authored
We have assigned error code to 'ret' if crop->type is not V4L2_BUF_TYPE_VIDEO_OUTPUT, but never use it. We'd better return the error code on this error. Signed-off-by:
-
Wei Yongjun authored
In case of error, the function vb2_dma_contig_init_ctx() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by:
-
Lad, Prabhakar authored
This patch allows enabling building of VPBE display driver for DM365 and DM355. This also removes unnecessary entry VIDEO_DM644X_VPBE in Kconfig, which could have been done with single entry, and appropriate changes in Makefile for building. Signed-off-by:
Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by:
-
Lad, Prabhakar authored
The vpbe driver can handle different platforms DM644X, DM36X and DM355. To differentiate between this platforms venc_type/vpbe_type was passed as part of platform data which was incorrect. The correct way to differentiate to handle this case is by passing different platform names. This patch creates platform_device_id[] array supporting different platforms and assigns id_table to the platform driver, and finally in the probe gets the actual device by using platform_get_device_id() and gets the appropriate driver data for that platform. Taking this approach will also make the DT transition easier. Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Manjunath Hadli authored
Add documentation on the Davinci VPFE driver. Document the subdevs, and private IOTCLs the driver implements. This patch also includes the TODO's to fit into drivers/media/ folder. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sakari Ailus <sakari.ailus@iki.fi> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Manjunath Hadli authored
add build infrastructure for dm365 specific modules for VPFE capture driver. Signed-off-by:
-
Manjunath Hadli authored
Add the video resizer driver with the v4l2 media controller framework which takes care of resizing the video frames with both up-scaling downscaling facility. The driver supports both continuous and single shot operations.The driver supports resizer as a subdevice and a media entity. It has support for 2 resizers - resizerA and resizerB. Signed-off-by:
-
Manjunath Hadli authored
IPIPE is the hardware IP which implements the functionality required for resizer, ipipe(colorspace converter) and the associated hardware support. This patch implements hardware setup including coefficient programming for various hardware filters, gamma, cfa and clock enabling. Signed-off-by:
-
Manjunath Hadli authored
Add the IPIPE subdevice to the DM365 vpfe driver. The IPIPE is the major sub IP in the DM365 capture VPFE hardware and implements black clamping, color space conversion, edge enhancements etc. the block is exposed as a subdevice and implements media controller based setup and a private IOCTL for fine grain control. Signed-off-by:
-
Manjunath Hadli authored
add support for ISIF as a subdevice for dm365 vpfe capture driver. ISIF is responsible for capturing video data both in raw bayer format on sync seperate signals and YUV through BT656/1120 interfaces. ISIF is exposed as a subdev for the vpfe driver and allows users to use the driver through standard media controller interface. Signed-off-by:
-
Manjunath Hadli authored
add support for dm365 IPIPEIF driver based on media framework. The IPIPEIF is exposed as a subdev, and it supports features like fault pixel correction, dark frame subtraction and other necessary hardware setup. Signed-off-by:
-
Manjunath Hadli authored
Add a generic video driver functionality to be used by all the vpfe drivers for davinci SoCs. The functionality includes all the standard v4l2 interfaces including streaming. The video node interface can be used both as an input and output node for both continuous and single shot modes. Also supports dv_presets to include HD modes, wth support for both user pointer IO and mmap. The buffering mechanism is based on videobuf2 interface. Signed-off-by:
-
Manjunath Hadli authored
Add the vpfe capture driver which implements media controller interface. The driver supports the DM365 sub ip units for capture namely - ISIF, IPIPE, IPIPEIF, Resizer. This file represents the main driver which does isr registration, v4l2 device registration, media registration and platform driver registrations. It calls the appropriate subdevs from here to create subdevices and media entities. Signed-off-by:
-
Manjunath Hadli authored
Add vpss helper functions to be used in the main driver for setting hardware parameters. Add interface functions to set sync polarity, interrupt completion and pageframe size in vpss to be used by the main driver. Signed-off-by:
-
Manjunath Hadli authored
request_mem_region for VPSS_CLK_CTRL register and ioremap. and enable clocks appropriately. Signed-off-by:
-
Manjunath Hadli authored
enable the clocks required for VPFE to work in PCCR register, and enbale ISIF out on BCR to get the correct operation from ISIF. Signed-off-by:
-
Sylwester Nawrocki authored
Make the pipeline try format routine more generic to support any number of subdevs in the pipeline, rather than hard coding it for only a sensor, MIPI-CSIS and FIMC subdevs and the FIMC video node. Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Hans de Goede authored
We already have the same delay in i2c_w8, but it was missing from i2c_w1, adding this delay fixes the Microsoft VX-3000 camera often (but not always) streaming video data with a very green-ish tint. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
We must wait for the previous i2c write to complete before starting a new one. Sofar we were getting away with this, but it seems that some parts of the usb-subsystem has been sped up making us go to fast :) This fixes streaming on sn9c103 based cams not working with an "i2c_w error" error. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Erik Andrén authored
Disable the hardware VFLIP and HFLIP controls for now as we lack a mechanism to adjust the frame offset, thus rending a bayerimage not compliant with the announced format. Signed-off-by:
Erik Andrén <erik.andren@gmail.com> Signed-off-by:
-
Sachin Kamat authored
module_usb_driver eliminates a lot of boilerplate by replacing module_init() and module_exit() calls. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Jacob Schloss authored
Add the USB ID for the Kinect for Windows RGB camera so it can be used with the gspca_kinect driver. Signed-off-by:
Jacob Schloss <jacob.schloss@unlimitedautomata.com> Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
-
Hans de Goede authored
When the v4l1 drivers were removed, there docs were forgotten. Signed-off-by:
-
Hans de Goede authored
The stk-webcam module is inserted upside-down in some webcams, so we need to de hflip and vflip by default on some models. Note that this patch inverts the value of the controls as reported by the control API in this case so that for the user they still make sense (iow not doing any flipping from the ctrl API pov results in an upright image). Reported-by:
Jose Gómez <adler@dreamcoder.org> Signed-off-by:
-
Hans de Goede authored
Some cams have their led connected in such a way that on = off and visa versa unfortunately we cannot tell this from the driver in any way, so add a module parameter for this. Reported-by:
Yuri Glushkov <yglushkov@yahoo.com> Signed-off-by:
-
Jean-François Moine authored
Setting the H and V flip controls at webcam connection time prevents the webcam to work correctly. This patch checks if the webcam is streaming before setting the flips. It does not set the flips (nor other controls) at webcam start time. Tested-by:
Philippe ROUBACH <philippe.roubach@free.fr> Signed-off-by:
Jean-François Moine <moinejf@free.fr> Signed-off-by:
-
Andrzej Hajda authored
Some sensors can have more than one pad (case of S5C73M3). In such cases FIMC assumes the last pad of the sensor is the source pad. Signed-off-by:
-
Sylwester Nawrocki authored
Add second source media pad for the FIFO data output to FIMC-IS and implement subdev s_stream op for configurations where FIMC-LITE is used as a glue logic between FIMC-IS and MIPI-CSIS or an image sensor. The second source media pad will be linked to the FIMC-LITE video node. For proper configuration the attached image sensor/video encoder properties are needed, like video bus type, signal polarities, etc. For this purpose there is a small routine added that walks the pipeline and returns the sensor subdev. Signed-off-by:
-
Sylwester Nawrocki authored
Add subdev group id definition for FIMC-IS ISP and sensor subdev. While at it rename all group id definitions to start with GRP_ID. Signed-off-by:
-
Sylwester Nawrocki authored
Dump registers contents together with the event counters state in VIDIOC_LOG_STATUS ioctl. Signed-off-by:
-
Sylwester Nawrocki authored
Enable only MIPI CSI-2 data lanes at the DPHY that are actively used, rather than unmasking all unconditionally. Signed-off-by:
-
Sylwester Nawrocki authored
The MIPI CSIS device supports MIPI CSI-2 RAW8, RAW10, RAW12 data types. Add related media bus pixel format definitions. This doesn't cover all possible supported media bus pixel formats. Signed-off-by:
-
