The scope of the "extra device ports" configuration is not made clear by
the CMN documentation - so far we've assumed it applies globally, based
on the sole example which suggests as much. However it transpires that
this is incorrect, and the format does in fact vary based on each
individual XP's port configuration. As a consequence, we're currenly
liable to decode the port/device indices from a node ID incorrectly,
thus program the wrong event source in the DTM leading to bogus event
counts, and also show device topology on the wrong ports in debugfs.

To put this right, rework node IDs yet again to carry around the
additional data necessary to decode them properly per-XP. At this point
the notion of fully decomposing an ID becomes more impractical than it's
worth, so unabstracting the XY mesh coordinates (where 2/3 users were
just debug anyway) ends up leaving things a bit simpler overall.

Fixes: 60d15040 ("perf/arm-cmn: Support new IP features")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/5195f990152fc37adba5fbf5929a6b11063d9f09.1725296395.git.robin.murphy@arm.comSigned-off-by: Will Deacon <will@kernel.org>

Currently users can get the Root Ports supported by the PCIe PMU by
"bus" sysfs attributes which indicates the PCIe bus number where
Root Ports are located. This maybe insufficient since Root Ports
supported by different PCIe PMUs may be located on the same PCIe bus.
So export the BDF range the Root Ports additionally.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240829090332.28756-4-yangyicong@huawei.comSigned-off-by: Will Deacon <will@kernel.org>

We make the initial value of event ctrl register as HISI_PCIE_INIT_SET
and modify according to the user options. This will make TLP headers
bandwidth only counting never take effect since HISI_PCIE_INIT_SET
configures to count the TLP payloads bandwidth. Fix this by making
the initial value of event ctrl register as 0.

Fixes: 17d57398 ("drivers/perf: hisi: Add TLP filter support")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240829090332.28756-3-yangyicong@huawei.comSigned-off-by: Will Deacon <will@kernel.org>

Currently we set the period and record it as the initial value of the
counter without checking it's set to the hardware successfully or not.
However the counter maybe unwritable if the target event is unsupported
by the device. In such case we will pass user a wrong count:

[start counts when setting the period]
hwc->prev_count = 0x8000000000000000
device.counter_value = 0 // the counter is not set as the period
[when user reads the counter]
event->count = device.counter_value - hwc->prev_count
             = 0x8000000000000000 // wrong. should be 0.

Fix this by record the hardware counter counts correctly when setting
the period.

Fixes: 8404b0fb ("drivers/perf: hisi: Add driver for HiSilicon PCIe PMU")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240829090332.28756-2-yangyicong@huawei.comSigned-off-by: Will Deacon <will@kernel.org>

Use perf_allow_kernel() for 'pa_enable' (physical addresses),
'pct_enable' (physical timestamps) and context IDs. This means that
perf_event_paranoid is now taken into account and LSM hooks can be used,
which is more consistent with other perf_event_open calls. For example
PERF_SAMPLE_PHYS_ADDR uses perf_allow_kernel() rather than just
perfmon_capable().

This also indirectly fixes the following error message which is
misleading because perf_event_paranoid is not taken into account by
perfmon_capable():

  $ perf record -e arm_spe/pa_enable/

  Error:
  Access to performance monitoring and observability operations is
  limited. Consider adjusting /proc/sys/kernel/perf_event_paranoid
  setting ...
Suggested-by: Al Grant <al.grant@arm.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240827145113.1224604-1-james.clark@linaro.org
Link: https://lore.kernel.org/all/20240807120039.GD37996@noisy.programming.kicks-ass.net/Signed-off-by: Will Deacon <will@kernel.org>

Update the vendor table with QCOM PCIe vendorid.
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240816-dwc_pmu_fix-v2-4-198b8ab1077c@quicinc.comSigned-off-by: Will Deacon <will@kernel.org>

When the PCIe devices are discovered late, the driver can't find
the PCIe devices and returns in the init without registering with
the bus notifier. Due to that the devices which are discovered late
the driver can't register for this.

Register for bus notifier & driver even if the device is not found
as part of init.

Fixes: af9597ad ("drivers/perf: add DesignWare PCIe PMU driver")
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240816-dwc_pmu_fix-v2-3-198b8ab1077c@quicinc.comSigned-off-by: Will Deacon <will@kernel.org>

Update document to reflect the driver change to use sbdf instead
of bdf alone.
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240816-dwc_pmu_fix-v2-2-198b8ab1077c@quicinc.comSigned-off-by: Will Deacon <will@kernel.org>

When there are multiple of instances of PCIe controllers, registration
to perf driver fails with this error.
sysfs: cannot create duplicate filename '/devices/platform/dwc_pcie_pmu.0'
CPU: 0 PID: 166 Comm: modprobe Not tainted 6.10.0-rc2-next-20240607-dirty
Hardware name: Qualcomm SA8775P Ride (DT)
Call trace:
 dump_backtrace.part.8+0x98/0xf0
 show_stack+0x14/0x1c
 dump_stack_lvl+0x74/0x88
 dump_stack+0x14/0x1c
 sysfs_warn_dup+0x60/0x78
 sysfs_create_dir_ns+0xe8/0x100
 kobject_add_internal+0x94/0x224
 kobject_add+0xa8/0x118
 device_add+0x298/0x7b4
 platform_device_add+0x1a0/0x228
 platform_device_register_full+0x11c/0x148
 dwc_pcie_register_dev+0x74/0xf0 [dwc_pcie_pmu]
 dwc_pcie_pmu_init+0x7c/0x1000 [dwc_pcie_pmu]
 do_one_initcall+0x58/0x1c0
 do_init_module+0x58/0x208
 load_module+0x1804/0x188c
 __do_sys_init_module+0x18c/0x1f0
 __arm64_sys_init_module+0x14/0x1c
 invoke_syscall+0x40/0xf8
 el0_svc_common.constprop.1+0x70/0xf4
 do_el0_svc+0x18/0x20
 el0_svc+0x28/0xb0
 el0t_64_sync_handler+0x9c/0xc0
 el0t_64_sync+0x160/0x164
kobject: kobject_add_internal failed for dwc_pcie_pmu.0 with -EEXIST,
don't try to register things with the same name in the same directory.

This is because of having same bdf value for devices under two different
controllers.

Update the logic to use sbdf which is a unique number in case of
multi instance also.

Fixes: af9597ad ("drivers/perf: add DesignWare PCIe PMU driver")
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240816-dwc_pmu_fix-v2-1-198b8ab1077c@quicinc.comSigned-off-by: Will Deacon <will@kernel.org>

The alibaba_uncore_pmu driver forgot to clear all interrupt status
in the interrupt processing function. After the PMU counter overflow
interrupt occurred, an interrupt storm occurred, causing the system
to hang.

Therefore, clear the correct interrupt status in the interrupt handling
function to fix it.

Fixes: cf7b6107 ("drivers/perf: add DDR Sub-System Driveway PMU driver for Yitian 710 SoC")
Signed-off-by: Jing Zhang <renyu.zj@linux.alibaba.com>
Reviewed-by: Shuai Xue <xueshuai@linux.alibaba.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1724297611-20686-1-git-send-email-renyu.zj@linux.alibaba.comSigned-off-by: Will Deacon <will@kernel.org>

This patch adds known PMU events that can be found on /usr/share/kpep in
macOS. The m1_pmu_events and m1_pmu_event_affinity are generated from
the script [1], which consumes the plist file from Apple. And then added
these events to m1_pmu_perf_map and m1_pmu_event_attrs with Apple's
documentation [2].

Link: https://github.com/cyyself/m1-pmu-gen [1]
Link: https://developer.apple.com/download/apple-silicon-cpu-optimization-guide/ [2]
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Acked-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/tencent_C5DA658E64B8D13125210C8D707CD8823F08@qq.comSigned-off-by: Will Deacon <will@kernel.org>

Armv9.4/8.9 PMU adds optional support for a fixed instruction counter
similar to the fixed cycle counter. Support for the feature is indicated
in the ID_AA64DFR1_EL1 register PMICNTR field. The counter is not
accessible in AArch32.

Existing userspace using direct counter access won't know how to handle
the fixed instruction counter, so we have to avoid using the counter
when user access is requested.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-7-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

There are 2 defines for the number of PMU counters:
ARMV8_PMU_MAX_COUNTERS and ARMPMU_MAX_HWEVENTS. Both are the same
currently, but Armv9.4/8.9 increases the number of possible counters
from 32 to 33. With this change, the maximum number of counters will
differ for KVM's PMU emulation which is PMUv3.4. Give KVM PMU emulation
its own define to decouple it from the rest of the kernel's number PMU
counters.

The VHE PMU code needs to match the PMU driver, so switch it to use
ARMPMU_MAX_HWEVENTS instead.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-6-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

The PMUv3 and KVM code each have a define for the PMU cycle counter
index. Move KVM's define to a shared location and use it for PMUv3
driver.
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-5-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

ARMV8_PMU_COUNTER_MASK is really a mask for the PMSELR_EL0.SEL register
field. Make that clear by adding a standard sysreg definition for the
register, and using it instead.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-4-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

Commit df29ddf4 ("arm64: perf: Abstract system register accesses
away") split off PMU register accessor functions to a standalone header.
Let's use it for KVM PMU code and get rid one copy of the ugly switch
macro.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-3-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

Various PMUv3 registers which are a mask of counters are 64-bit
registers, but the accessor functions take a u32. This has been fine as
the upper 32-bits have been RES0 as there has been a maximum of 32
counters prior to Armv9.4/8.9. With Armv9.4/8.9, a 33rd counter is
added. Update the accessor functions to use a u64 instead.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-2-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

Xscale and Armv6 PMUs defined the cycle counter at 0 and event counters
starting at 1 and had 1:1 event index to counter numbering. On Armv7 and
later, this changed the cycle counter to 31 and event counters start at
0. The drivers for Armv7 and PMUv3 kept the old event index numbering
and introduced an event index to counter conversion. The conversion uses
masking to convert from event index to a counter number. This operation
relies on having at most 32 counters so that the cycle counter index 0
can be transformed to counter number 31.

Armv9.4 adds support for an additional fixed function counter
(instructions) which increases possible counters to more than 32, and
the conversion won't work anymore as a simple subtract and mask. The
primary reason for the translation (other than history) seems to be to
have a contiguous mask of counters 0-N. Keeping that would result in
more complicated index to counter conversions. Instead, store a mask of
available counters rather than just number of events. That provides more
information in addition to the number of events.

No (intended) functional changes.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240731-arm-pmu-3-9-icntr-v3-1-280a8d7ff465@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

Use of_property_present() to test for property presence rather than
of_find_property(). This is part of a larger effort to remove callers
of of_find_property() and similar functions. of_find_property() leaks
the DT struct property and data pointers which is a problem for
dynamically allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20240731191312.1710417-15-robh@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>

Pull x86 fixes from Thomas Gleixner:

 - Fix 32-bit PTI for real.

   pti_clone_entry_text() is called twice, once before initcalls so that
   initcalls can use the user-mode helper and then again after text is
   set read only. Setting read only on 32-bit might break up the PMD
   mapping, which makes the second invocation of pti_clone_entry_text()
   find the mappings out of sync and failing.

   Allow the second call to split the existing PMDs in the user mapping
   and synchronize with the kernel mapping.

 - Don't make acpi_mp_wake_mailbox read-only after init as the mail box
   must be writable in the case that CPU hotplug operations happen after
   boot. Otherwise the attempt to start a CPU crashes with a write to
   read only memory.

 - Add a missing sanity check in mtrr_save_state() to ensure that the
   fixed MTRR MSRs are supported.

   Otherwise mtrr_save_state() ends up in a #GP, which is fixed up, but
   the WARN_ON() can bring systems down when panic on warn is set.

* tag 'x86-urgent-2024-08-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mtrr: Check if fixed MTRRs exist before saving them
  x86/paravirt: Fix incorrect virt spinlock setting on bare metal
  x86/acpi: Remove __ro_after_init from acpi_mp_wake_mailbox
  x86/mm: Fix PTI for i386 some more

Pull time keeping fixes from Thomas Gleixner:

 - Fix a couple of issues in the NTP code where user supplied values are
   neither sanity checked nor clamped to the operating range. This
   results in integer overflows and eventualy NTP getting out of sync.

   According to the history the sanity checks had been removed in favor
   of clamping the values, but the clamping never worked correctly under
   all circumstances. The NTP people asked to not bring the sanity
   checks back as it might break existing applications.

   Make the clamping work correctly and add it where it's missing

 - If adjtimex() sets the clock it has to trigger the hrtimer subsystem
   so it can adjust and if the clock was set into the future expire
   timers if needed. The caller should provide a bitmask to tell
   hrtimers which clocks have been adjusted.

   adjtimex() uses not the proper constant and uses CLOCK_REALTIME
   instead, which is 0. So hrtimers adjusts only the clocks, but does
   not check for expired timers, which might make them expire really
   late. Use the proper bitmask constant instead.

* tag 'timers-urgent-2024-08-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix bogus clock_was_set() invocation in do_adjtimex()
  ntp: Safeguard against time_constant overflow
  ntp: Clamp maxerror and esterror to operating range

Pull irq fixes from Thomas Gleixner:
 "Three small fixes for interrupt core and drivers:

   - The interrupt core fails to honor caller supplied affinity hints
     for non-managed interrupts and uses the system default affinity on
     startup instead. Set the missing flag in the descriptor to tell the
     core to use the provided affinity.

   - Fix a shift out of bounds error in the Xilinx driver

   - Handle switching to level trigger correctly in the RISCV APLIC
     driver. It failed to retrigger the interrupt which causes it to
     become stale"

* tag 'irq-urgent-2024-08-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/riscv-aplic: Retrigger MSI interrupt on source configuration
  irqchip/xilinx: Fix shift out of bounds
  genirq/irqdesc: Honor caller provided affinity in alloc_desc()

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for reported issues for
  6.11-rc3. Included in here are:

   - usb serial driver MODULE_DESCRIPTION() updates

   - usb serial driver fixes

   - typec driver fixes

   - usb-ip driver fix

   - gadget driver fixes

   - dt binding update

  All of these have been in linux-next with no reported issues"

* tag 'usb-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: ucsi: Fix a deadlock in ucsi_send_command_common()
  usb: typec: tcpm: avoid sink goto SNK_UNATTACHED state if not received source capability message
  usb: gadget: f_fs: pull out f->disable() from ffs_func_set_alt()
  usb: gadget: f_fs: restore ffs_func_disable() functionality
  USB: serial: debug: do not echo input by default
  usb: typec: tipd: Delete extra semi-colon
  usb: typec: tipd: Fix dereferencing freeing memory in tps6598x_apply_patch()
  usb: gadget: u_serial: Set start_delayed during suspend
  usb: typec: tcpci: Fix error code in tcpci_check_std_output_cap()
  usb: typec: fsa4480: Check if the chip is really there
  usb: gadget: core: Check for unset descriptor
  usb: vhci-hcd: Do not drop references before new references are gained
  usb: gadget: u_audio: Check return codes from usb_ep_enable and config_ep_by_speed.
  usb: gadget: midi2: Fix the response for FB info with block 0xff
  dt-bindings: usb: microchip,usb2514: Add USB2517 compatible
  USB: serial: garmin_gps: use struct_size() to allocate pkt
  USB: serial: garmin_gps: annotate struct garmin_packet with __counted_by
  USB: serial: add missing MODULE_DESCRIPTION() macros
  USB: serial: spcp8x5: remove unused struct 'spcp8x5_usb_ctrl_arg'

Pull tty / serial driver fixes from Greg KH:
 "Here are some small tty and serial driver fixes for reported problems
  for 6.11-rc3. Included in here are:

   - sc16is7xx serial driver fixes

   - uartclk bugfix for a divide by zero issue

   - conmakehash userspace build issue fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: vt: conmakehash: cope with abs_srctree no longer in env
  serial: sc16is7xx: fix invalid FIFO access with special register set
  serial: sc16is7xx: fix TX fifo corruption
  serial: core: check uartclk for zero to avoid divide by zero

Merge tag 'driver-core-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core / documentation fixes from Greg KH:
 "Here are some small fixes, and some documentation updates for
  6.11-rc3. Included in here are:

   - embargoed hardware documenation updates based on a lot of review by
     legal-types in lots of companies to try to make the process a _bit_
     easier for us to manage over time.

   - rust firmware documentation fix

   - driver detach race fix for the fix that went into 6.11-rc1

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'driver-core-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: Fix uevent_show() vs driver detach race
  Documentation: embargoed-hardware-issues.rst: add a section documenting the "early access" process
  Documentation: embargoed-hardware-issues.rst: minor cleanups and fixes
  rust: firmware: fix invalid rustdoc link

Pull char/misc fixes from Greg KH:
 "Here are some small char/misc/other driver fixes for 6.11-rc3 for
  reported issues. Included in here are:

   - binder driver fixes

   - fsi MODULE_DESCRIPTION() additions (people seem to love them...)

   - eeprom driver fix

   - Kconfig dependency fix to resolve build issues

   - spmi driver fixes

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'char-misc-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  spmi: pmic-arb: add missing newline in dev_err format strings
  spmi: pmic-arb: Pass the correct of_node to irq_domain_add_tree
  binder_alloc: Fix sleeping function called from invalid context
  binder: fix descriptor lookup for context manager
  char: add missing NetWinder MODULE_DESCRIPTION() macros
  misc: mrvl-cn10k-dpi: add PCI_IOV dependency
  eeprom: ee1004: Fix locking issues in ee1004_probe()
  fsi: add missing MODULE_DESCRIPTION() macros

Pull SCSI fixes from James Bottomley:
 "Two core fixes: one to prevent discard type changes (seen on iSCSI)
  during intermittent errors and the other is fixing a lockdep problem
  caused by the queue limits change.

  And one driver fix in ufs"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: sd: Keep the discard mode stable
  scsi: sd: Move sd_read_cpr() out of the q->limits_lock region
  scsi: ufs: core: Fix hba->last_dme_cmd_tstamp timestamp updating logic

Pull nfsd fixes from Chuck Lever:

 - Two minor fixes for recent changes

* tag 'nfsd-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  nfsd: don't set SVC_SOCK_ANONYMOUS when creating nfsd sockets
  sunrpc: avoid -Wformat-security warning

Pull i2c fixes from Wolfram Sang:

 - Two fixes for SMBusAlert handling in the I2C core: one to avoid an
   endless loop when scanning for handlers and one to make sure handlers
   are always called even if HW has broken behaviour

 - I2C header build fix for when ACPI is enabled but I2C isn't

 - The testunit gets a rename in the code to match the documentation

 - Two fixes for the Qualcomm GENI I2C controller are cleaning up the
   error exit patch in the runtime_resume() function. The first is
   disabling the clock, the second disables the icc on the way out

* tag 'i2c-for-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: testunit: match HostNotify test name with docs
  i2c: qcom-geni: Add missing geni_icc_disable in geni_i2c_runtime_resume
  i2c: qcom-geni: Add missing clk_disable_unprepare in geni_i2c_runtime_resume
  i2c: Fix conditional for substituting empty ACPI functions
  i2c: smbus: Send alert notifications to all devices if source not found
  i2c: smbus: Improve handling of stuck alerts

Pull dma-mapping fix from Christoph Hellwig:

 - avoid a deadlock with dma-debug and netconsole (Rik van Riel)

* tag 'dma-mapping-6.11-2024-08-10' of git://git.infradead.org/users/hch/dma-mapping:
  dma-debug: avoid deadlock between dma debug vs printk and netconsole

Pull more bcachefs fixes from Kent Overstreet:
 "A couple last minute fixes for the new disk accounting

   - fix a bug that was causing ACLs to seemingly "disappear"

   - new on disk format version, bcachefs_metadata_version_disk_accounting_v3

     bcachefs_metadata_version_disk_accounting_v2 accidentally included
     padding in disk_accounting_key; fortunately, 6.11 isn't out yet so
     we can fix this with another version bump"

* tag 'bcachefs-2024-08-10' of git://evilpiepirate.org/bcachefs:
  bcachefs: bcachefs_metadata_version_disk_accounting_v3
  bcachefs: improve bch2_dev_usage_to_text()
  bcachefs: bch2_accounting_invalid()
  bcachefs: Switch to .get_inode_acl()

The section 4.5.2 of the RISC-V AIA specification says that "any write
to a sourcecfg register of an APLIC might (or might not) cause the
corresponding interrupt-pending bit to be set to one if the rectified
input value is high (= 1) under the new source mode."

When the interrupt type is changed in the sourcecfg register, the APLIC
device might not set the corresponding pending bit, so the interrupt might
never become pending.

To handle sourcecfg register changes for level-triggered interrupts in MSI
mode, manually set the pending bit for retriggering interrupt so it gets
retriggered if it was already asserted.

Fixes: ca8df97f ("irqchip/riscv-aplic: Add support for MSI-mode")
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240809071049.2454-1-yongxuan.wang@sifive.com

The device tree property 'xlnx,kind-of-intr' is sanity checked that the
bitmask contains only set bits which are in the range of the number of
interrupts supported by the controller.

The check is done by shifting the mask right by the number of supported
interrupts and checking the result for zero.

The data type of the mask is u32 and the number of supported interrupts is
up to 32. In case of 32 interrupts the shift is out of bounds, resulting in
a mismatch warning. The out of bounds condition is also reported by UBSAN:

  UBSAN: shift-out-of-bounds in irq-xilinx-intc.c:332:22
  shift exponent 32 is too large for 32-bit type 'unsigned int'

Fix it by promoting the mask to u64 for the test.

Fixes: d50466c9 ("microblaze: intc: Refactor DT sanity check")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/1723186944-3571957-1-git-send-email-radhey.shyam.pandey@amd.com

Pull smb client fixes from Steve French:

 - DFS fix

 - fix for security flags for requiring encryption

 - minor cleanup

* tag '6.11-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: cifs_inval_name_dfs_link_error: correct the check for fullpath
  Fix spelling errors in Server Message Block
  smb3: fix setting SecurityFlags when encryption is required

Pull spi fixes from Mark Brown:
 "A few SPI fixes: clock rate calculation fixes for the Kunpeng and lpsi
  drivers and a missing registration of a device ID for spidev (which
  had only been updated for DT cases, causing warnings)"

* tag 'spi-fix-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: spi-fsl-lpspi: Fix scldiv calculation
  spi: spidev: Add missing spi_device_id for bh2228fv
  spi: hisi-kunpeng: Add verification for the max_frequency provided by the firmware
  spi: hisi-kunpeng: Add validation for the minimum value of speed_hz

bcachefs_metadata_version_disk_accounting_v2 erroneously had padding
bytes in disk_accounting_key, which is a problem because we have to
guarantee that all unused bytes in disk_accounting_key are zeroed.

Fortunately 6.11 isn't out yet, so it's cheap to fix this by spinning a
new version.
Reported-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Pull drm fixes from Dave Airlie:
 "Weekly regular fixes, mostly amdgpu with i915/xe having a few each,
  and then some misc bits across the board, seems about right for rc3
  time.

  client:
   - fix null ptr deref

  bridge:
   - connector: fix double free

  atomic:
   - fix async flip update

  panel:
   - document panel

  omap:
   - add config dependency

  tests:
   - fix gem shmem test

  drm buddy:
   - Add start address to trim function

  amdgpu:
   - DMCUB fix
   - Fix DET programming on some DCNs
   - DCC fixes
   - DCN 4.0.1 fixes
   - SMU 14.0.x update
   - MMHUB fix
   - DCN 3.1.4 fix
   - GC 12.0 fixes
   - Fix soft recovery error propogation
   - SDMA 7.0 fixes
   - DSC fix

  xe:
   - Fix off-by-one when processing RTP rules
   - Use dma_fence_chain_free in chain fence unused as a sync
   - Fix PL1 disable flow in xe_hwmon_power_max_write
   - Take ref to VM in delayed dump snapshot

  i915:
   - correct dual pps handling for MTL_PCH+ [display]
   - Adjust vma offset for framebuffer mmap offset [gem]
   - Fix Virtual Memory mapping boundaries calculation [gem]
   - Allow evicting to use the requested placement
   - Attempt to get pages without eviction first"

* tag 'drm-fixes-2024-08-10' of https://gitlab.freedesktop.org/drm/kernel: (31 commits)
  drm/xe: Take ref to VM in delayed snapshot
  drm/xe/hwmon: Fix PL1 disable flow in xe_hwmon_power_max_write
  drm/xe: Use dma_fence_chain_free in chain fence unused as a sync
  drm/xe/rtp: Fix off-by-one when processing rules
  drm/amdgpu: Add DCC GFX12 flag to enable address alignment
  drm/amdgpu: correct sdma7 max dw
  drm/amdgpu: Add address alignment support to DCC buffers
  drm/amd/display: Skip Recompute DSC Params if no Stream on Link
  drm/amdgpu: change non-dcc buffer copy configuration
  drm/amdgpu: Forward soft recovery errors to userspace
  drm/amdgpu: add golden setting for gc v12
  drm/buddy: Add start address support to trim function
  drm/amd/display: Add missing program DET segment call to pipe init
  drm/amd/display: Add missing DCN314 to the DML Makefile
  drm/amdgpu: force to use legacy inv in mmhub
  drm/amd/pm: update powerplay structure on smu v14.0.2/3
  drm/amd/display: Add missing mcache registers
  drm/amd/display: Add dcc propagation value
  drm/amd/display: Add missing DET segments programming
  drm/amd/display: Replace dm_execute_dmub_cmd with dc_wake_and_execute_dmub_cmd
  ...

Add a line for capacity
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Implement bch2_accounting_invalid(); check for junk at the end, and
replicas accounting entries in particular need to be checked or we'll
pop asserts later.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>