This patch adds IKS (In Kernel Switcher) support to cpufreq driver.

This creates a combined freq table for A7-A15 CPU pairs. A7 frequencies
are virtualized and scaled down to half the actual frequencies to
approximate a linear scale across the combined A7+A15 range. When the
requested frequency change crosses the A7-A15 boundary a cluster switch
is invoked.

Based on earlier work from Sudeep KarkadaNagesha.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch adds vexpress-spc platform device to enables the vexpress
SPC cpufreq interface driver.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Pawel Moll <Pawel.Moll@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The TC2(i.e. CA15_A7) Versatile Express has external Cortex M3 based
power controller which is responsible for CPU DVFS and SPC provides
the interface for the same.

This patch adds a tiny interface driver to check if OPPs are
initialised by SPC platform code and register the arm_big_little
cpufreq driver.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

On TC2, the cpu clocks are controlled by the external M3 microcontroller
and SPC provides the interface between the CPU and the power controller.

The generic cpufreq drivers use the clock APIs to get the cpu clocks.
This patch add virtual spc clocks for all the cpus to control the cpu
operating frequency via the clock framework.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Pawel Moll <Pawel.Moll@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

SPC(Serial Power Controller) on TC2 also controls the CPU performance
operating points which is essential to provide CPU DVFS. The M3
microcontroller provides two sets of eight performance values, one set
for each cluster (CA15 or CA7). Each of this value contains the
frequency(kHz) and voltage(mV) at that performance level. It expects
these performance level to be passed through the SPC PERF_LVL registers.

This patch adds support to populate these performance levels from M3,
build the mapping to CPU OPPs at the boot and then use it to get and
set the CPU performance level runtime.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Pawel Moll <Pawel.Moll@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

We have per-CPU cpu_policy_rwsem for cpufreq core, but we never use
all of them. We always use rwsem of policy->cpu and so we can
actually make this rwsem per policy instead.

This patch does this change. With this change other tricky situations
are also avoided now, like which lock to take while we are changing
policy->cpu, etc.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add support for the Baytrail processor.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Non-core processors have a different MSR layout to commumicate P state
information. Refactor the driver to use CPU dependent accessors to
P state information.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently, the prototype of cpufreq_drivers target routines is:

int target(struct cpufreq_policy *policy, unsigned int target_freq,
		unsigned int relation);

And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.

So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.

This patch implements the new light weight prototype for target_index() routine.
It looks like this:

int target_index(struct cpufreq_policy *policy, unsigned int index);

CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.

This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.

It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>

Conflicts:
	drivers/cpufreq/omap-cpufreq.c

Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.

Affected structures are:
 struct opp
 enum opp_event

Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.

Affected functions are:
 opp_get_voltage
 opp_get_freq
 opp_get_opp_count
 opp_find_freq_exact
 opp_find_freq_floor
 opp_find_freq_ceil
 opp_add
 opp_enable
 opp_disable
 opp_get_notifier
 opp_init_cpufreq_table
 opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull btrfs fix from Chris Mason:
 "Sage hit a deadlock with ceph on btrfs, and Josef tracked it down to a
  regression in our initial rc1 pull.  When doing nocow writes we were
  sometimes starting a transaction with locks held"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: release path before starting transaction in can_nocow_extent

Pull ACPI and power management fixes from Rafael Wysocki:

 - intel_pstate fix for misbehavior after system resume if sysfs
   attributes are set in a specific way before the corresponding suspend
   from Dirk Brandewie.

 - A recent intel_pstate fix has no effect if unsigned long is 32-bit,
   so fix it up to cover that case as well.

 - The s3c64xx cpufreq driver was not updated when the index field of
   struct cpufreq_frequency_table was replaced with driver_data, so
   update it now.  From Charles Keepax.

 - The Kconfig help text for ACPI_BUTTON still refers to
   /proc/acpi/event that has been dropped recently, so modify it to
   remove that reference.  From Krzysztof Mazur.

 - A Lan Tianyu's change adds a missing mutex unlock to an error code
   path in acpi_resume_power_resources().

 - Some code related to ACPI power resources, whose very purpose is
   questionable to put it lightly, turns out to cause problems to happen
   during testing on real systems, so remove it completely (we may
   revisit that in the future if there's a compelling enough reason).
   From Rafael J Wysocki and Aaron Lu.

* tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Drop two functions that are not used any more
  ATA / ACPI: remove power dependent device handling
  cpufreq: s3c64xx: Rename index to driver_data
  ACPI / power: Drop automaitc resume of power resource dependent devices
  intel_pstate: Fix type mismatch warning
  cpufreq / intel_pstate: Fix max_perf_pct on resume
  ACPI: remove /proc/acpi/event from ACPI_BUTTON help
  ACPI / power: Release resource_lock after acpi_power_get_state() return error

Pull x86 fixes from Ingo Molnar:
 "Two fixlets:

   - fix a (rare-config) build bug
   - fix a next-gen SGI/UV hw/firmware enumeration bug"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Update UV3 hub revision ID
  x86/microcode: Correct Kconfig dependencies

We can't be holding tree locks while we try to start a transaction, we will
deadlock.  Thanks,
Reported-by: Sage Weil <sage@inktank.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

* acpi-fixes:
  ACPI / PM: Drop two functions that are not used any more
  ATA / ACPI: remove power dependent device handling
  ACPI / power: Drop automaitc resume of power resource dependent devices
  ACPI: remove /proc/acpi/event from ACPI_BUTTON help
  ACPI / power: Release resource_lock after acpi_power_get_state() return error

* pm-fixes:
  cpufreq: s3c64xx: Rename index to driver_data
  intel_pstate: Fix type mismatch warning
  cpufreq / intel_pstate: Fix max_perf_pct on resume

Pull CIFS fixes from Steve French:
 "Five small cifs fixes (includes fixes for: unmount hang, 2 security
  related, symlink, large file writes)"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: ntstatus_to_dos_map[] is not terminated
  cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
  cifs: Fix inability to write files >2GB to SMB2/3 shares
  cifs: Avoid umount hangs with smb2 when server is unresponsive
  do not treat non-symlink reparse points as valid symlinks

cpufreq_set_policy() has been changed to origin __cpufreq_set_policy()
and policy->lock has been converted to rewrite lock by commit 5a01f2.
So remove the comment.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Merge tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is one fix for the hotplug memory path that resolves a regression
  when removing memory that showed up in 3.12-rc1"

* tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: Release device_hotplug_lock when store_mem_state returns EINVAL

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 3.12-rc6

  The largest change here is a bunch of new device ids for the option
  USB serial driver for new Huawei devices.  Other than that, just some
  small bug fixes for issues that people have reported (run-time and
  build-time), nothing major"

* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
  usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
  usb/chipidea: fix oops on memory allocation failure
  usb-storage: add quirk for mandatory READ_CAPACITY_16
  usb: serial: option: blacklist Olivetti Olicard200
  USB: quirks: add touchscreen that is dazzeled by remote wakeup
  Revert "usb: musb: gadget: fix otg active status flag"
  USB: quirks.c: add one device that cannot deal with suspension
  USB: serial: option: add support for Inovia SEW858 device
  USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
  USB: support new huawei devices in option.c
  usb: musb: start musb on the udc side, too
  xhci: Fix spurious wakeups after S5 on Haswell
  xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
  xhci: quirk for extra long delay for S4
  xhci: Don't enable/disable RWE on bus suspend/resume.

Pull serial driver fixes from Greg KH:
 "Here are two serial driver fixes for your tree.  One is a revert of a
  patch that causes a build error, the other is a fix to provide the
  correct brace placement which resolves a bug where the driver was not
  working properly"

* tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: vt8500: add missing braces
  Revert "serial: i.MX: evaluate linux,stdout-path property"

Pull char/misc driver fixes from Greg KH:
 "Here are some small iio and w1 driver fixes for 3.12-rc6.

  There is also a hyper-v fix in here, which turned out to be incorrect,
  so it was reverted.  That will probably have to wait unto 3.13-rc1 to
  get accepted as it's still being discussed"

* tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Revert "Drivers: hv: vmbus: Fix a bug in channel rescind code"
  Drivers: hv: vmbus: Fix a bug in channel rescind code
  iio:buffer: Free active scan mask in iio_disable_all_buffers()
  iio: frequency: adf4350: add missing clk_disable_unprepare() on error in adf4350_probe()
  w1 - call request_module with w1 master mutex unlocked
  w1 - fix fops in w1_bus_notify

Pull sound fixes from Takashi Iwai:
 "All reasonably small fixes as rc6: a HD-audio mic fix, a us122l mmap
  regression fix, and kernel memory leak fix in hdsp driver.  Hopefully
  this will be the last pull request for 3.12..."

* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hdsp - info leak in snd_hdsp_hwdep_ioctl()
  ALSA: us122l: Fix pcm_usb_stream mmapping regression
  ALSA: hda - Fix inverted internal mic not indicated on some machines

Pull apparmor fixes from James Morris:
 "A couple more regressions fixed"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  apparmor: fix bad lock balance when introspecting policy
  apparmor: fix memleak of the profile hash

Merge tag 'iio-fixes-for-3.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus

Jonathan writes:

Third set of IIO fixes for the 3.12 cycle.

Two little ones this time:

1) A missing clk_unprepare in adf4350.
2) A missing free of the active_scan_mask when iio_disable_all_buffers is
called during an unexpected device removal.  This leak was introduced by
the fix
a87c82e4 iio: Stop sampling when the device is removed
and hence is a regression fix.

Commit 3fa4d734 (usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv)
changed the conditional around the declaration of usb_nop_xceiv_register
from
	#if defined(CONFIG_NOP_USB_XCEIV) ||
		(defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
to
	#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)

While that looks the same, it is semantically different. The first expression
is true if CONFIG_NOP_USB_XCEIV is built as module and if the including
code is built as module. The second expression is true if code depending on
CONFIG_NOP_USB_XCEIV if built as module or into the kernel.

As a result, the arm:allmodconfig build fails with

arch/arm/mach-omap2/built-in.o: In function `omap3_evm_init':
arch/arm/mach-omap2/board-omap3evm.c:703: undefined reference to
	`usb_nop_xceiv_register'

Fix the problem by reverting to the old conditional.

Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 90d33f3e as it's not
the correct fix for this issue, and it causes a build warning to be
added to the kernel tree.

Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.

Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node.  However, this
code has no effect after commit 41863fce (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.

[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In the exynos4210_set_apll() function, the APLL frequency is set with
direct register manipulation.

Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.

Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.

Tested at:
- Exynos4210 - Trats board (linux 3.12-rc4)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In the exynos4x12_set_apll() function, the APLL frequency is set with
direct register manipulation.

Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.

Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.

Tested at:
- Exynos4412 - Trats2 board (linux 3.12-rc4)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Merge misc fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
  mm: revert mremap pud_free anti-fix
  mm: fix BUG in __split_huge_page_pmd
  swap: fix set_blocksize race during swapon/swapoff
  procfs: call default get_unmapped_area on MMU-present architectures
  procfs: fix unintended truncation of returned mapped address
  writeback: fix negative bdi max pause
  percpu_refcount: export symbols
  fs: buffer: move allocation failure loop into the allocator
  mm: memcg: handle non-error OOM situations more gracefully
  tools/testing/selftests: fix uninitialized variable
  block/partitions/efi.c: treat size mismatch as a warning, not an error
  mm: hugetlb: initialize PG_reserved for tail pages of gigantic compound pages
  mm/zswap: bugfix: memory leak when re-swapon
  mm: /proc/pid/pagemap: inspect _PAGE_SOFT_DIRTY only on present pages
  mm: migration: do not lose soft dirty bit if page is in migration state
  gcov: MAINTAINERS: Add an entry for gcov
  mm/hugetlb.c: correct missing private flag clearing
  mm/vmscan.c: don't forget to free shrinker->nr_deferred
  ipc/sem.c: synchronize semop and semctl with IPC_RMID
  ipc: update locking scheme comments
  ...

Revert commit 1ecfd533 ("mm/mremap.c: call pud_free() after fail
calling pmd_alloc()").

The original code was correct: pud_alloc(), pmd_alloc(), pte_alloc_map()
ensure that the pud, pmd, pt is already allocated, and seldom do they
need to allocate; on failure, upper levels are freed if appropriate by
the subsequent do_munmap().  Whereas commit 1ecfd533 did an
unconditional pud_free() of a most-likely still-in-use pud: saved only
by the near-impossiblity of pmd_alloc() failing.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Occasionally we hit the BUG_ON(pmd_trans_huge(*pmd)) at the end of
__split_huge_page_pmd(): seen when doing madvise(,,MADV_DONTNEED).

It's invalid: we don't always have down_write of mmap_sem there: a racing
do_huge_pmd_wp_page() might have copied-on-write to another huge page
before our split_huge_page() got the anon_vma lock.

Forget the BUG_ON, just go back and try again if this happens.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix race between swapoff and swapon.  Swapoff used old_block_size from
swap_info outside of swapon_mutex so it could be overwritten by
concurrent swapon.

The race has visible effect only if more than one swap block device
exists with different block sizes (e.g.  /dev/sda1 with block size 4096
and /dev/sdb1 with 512).  In such case it leads to setting the blocksize
of swapped off device with wrong blocksize.

The bug can be triggered with multiple concurrent swapoff and swapon:
0. Swap for some device is on.
1. swapoff:
First the swapoff is called on this device and "struct swap_info_struct
*p" is assigned. This is done under swap_lock however this lock is
released for the call try_to_unuse().

2. swapon:
After the assignment above (and before acquiring swapon_mutex &
swap_lock by swapoff) the swapon is called on the same device.
The p->old_block_size is assigned to the value of block_size the device.
This block size should be the same as previous but sometimes it is not.
The swapon ends successfully.

3. swapoff:
Swapoff resumes, grabs the locks and mutex and continues to disable this
swap device. Now it sets the block size to value taken from swap_info
which was overwritten by swapon in 2.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Weijie Yang <weijie.yang.kh@gmail.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Shaohua Li <shli@fusionio.com>
Cc: Minchan Kim <minchan@kernel.org>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit c4fe2448 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file,
which causes regression of mmap on /proc/vmcore.

To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e.  the one in actual file
operation in the procfs file, is not defined.
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>