- 03 Sep, 2020 13 commits
-
-
Daniel Campello authored
Improves readability by storing &client->dev in a local variable. Signed-off-by:
Daniel Campello <campello@chromium.org> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Daniel Campello authored
Checks for non-zero return values to signal error conditions. Signed-off-by:
-
Daniel Campello authored
Fixes wrong copyright year. Signed-off-by:
-
Daniel Campello authored
Simplify compensation stage by using regmap_read_poll_timeout(). Signed-off-by:
-
Daniel Campello authored
Uses for_each_set_bit() macro to loop over channel bitmaps. Signed-off-by:
-
Daniel Campello authored
Makes use __aligned(8) to ensure that the timestamp is correctly aligned when we call io_push_to_buffers_with_timestamp(). Also makes use of sizeof() for regmap_bulk_read instead of static value. Signed-off-by:
-
Daniel Campello authored
Uses .probe_new in place of .probe. Also uses device_get_match_data() for whoami matching. Signed-off-by:
-
Daniel Campello authored
Avoids unused warnings due to acpi/of table macros. Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
-
Daniel Campello authored
Fixes enable/disable irq handling at various points. The driver needs to only enable/disable irqs if there is an actual irq handler installed. Signed-off-by:
-
Daniel Campello authored
Follows spec sheet for macro declarations. Signed-off-by:
-
Daniel Campello authored
Adds device tree bindings for sx9310 sensor. Signed-off-by:
Douglas Anderson <dianders@chromium.org> [swboyd@chromium.org: Add both regulators and make them optional] Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Jonathan Cameron authored
Simple device with a simple conversion. Special handling needed for the max1118 which is the only supported part that has an external reference voltage. Cc: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Christian Eggers authored
Support for AMS AS73211 JENCOLOR(R) Digital XYZ Sensor. This driver has no built-in trigger. In order for making triggered measurements, an external (software) trigger driver like iio-trig-hrtimer or iio-trig-sysfs is required. The sensor supports single and continuous measurement modes. The latter is not used by design as this would require tight timing synchronization between hardware and driver without much benefit. Datasheet: https://ams.com/documents/20143/36005/AS73211_DS000556_3-01.pdfSigned-off-by:
Christian Eggers <ceggers@arri.de> Reviewed-by:
-
- 22 Aug, 2020 16 commits
-
-
Christian Eggers authored
Add DT bindings for AMS AS73211 XYZ True Color Sensor. Signed-off-by:
-
Calvin Glisson authored
Remove excess blank line after variable declarations. Improves code consistency and readability. Change suggested by checkpatch.pl: CHECK: Please don't use multiple blank lines Signed-off-by:
Calvin Glisson <taragaram@gmail.com> Signed-off-by:
-
Randy Dunlap authored
Drop the repeated word "and" in a comment. Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Jonathan Cameron authored
Straight forward conversion of this binding for this current sense amplifier and ADC. Signed-off-by:
Jacopo Mondi <jacopo@jmondi.org> Reviewed-by:
-
Jonathan Cameron authored
Straight forward conversion for this SPI ADC. Added limits on spi-max-frequency from datasheet (0.1 to 4.8MHz) Signed-off-by:
-
Nishant Malpani authored
Add devicetree binding document for ADXRS290, a dual-axis MEMS gyroscope. Reviewed-by:
Nishant Malpani <nish.malpani25@gmail.com> Signed-off-by:
-
Nishant Malpani authored
ADXRS290 is a high performance MEMS pitch and roll (dual-axis in-plane) angular rate sensor (gyroscope) designed for use in stabilization applications. It also features an internal temperature sensor and programmable high-pass and low-pass filters. Add support for ADXRS290 in direct-access mode for now. Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXRS290.pdfReviewed-by:
-
Ankit Baluni authored
Added a missing comma and changed 'it it useful' to 'it is useful'. Signed-off-by:
Ankit Baluni <b18007@students.iitmandi.ac.in> Reviewed-by:
-
Lars-Peter Clausen authored
Make sure that the trigger function stubs are all static inline. Otherwise we might see compiler warnings about declared but unused functions. Fixes 77712e5f: ("Staging: iio: Staticise non-exported functions") Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
-
Matt Ranostay authored
Cc: devicetree@vger.kernel.org Signed-off-by:
Matt Ranostay <matt.ranostay@konsulko.com> Acked-by:
-
Alexandru Ardelean authored
The change is mostly cosmetic. When looking into the menuconfig help of the ad8366 driver, the HMC1119 chip should also show up (since the driver supports it). Signed-off-by:
-
Stefan Popa authored
The driver does not have a struct of_device_id table, but supported devices are registered via Device Trees. This patch adds OF device ID table. Signed-off-by:
Stefan Popa <stefan.popa@analog.com> Signed-off-by:
-
Alexandru Ardelean authored
The change is mostly stylistic. The table should be indented with tabs instead of spaces. Signed-off-by:
-
Alexandru Ardelean authored
The driver pretty much uses device managed functions. The only left-over is the iio_device_register() function, which also requires an action-or-reset hook to disable the regulator on the remove and error path. Signed-off-by:
-
Matt Ranostay authored
Add support for the Atlas EZO O2 chemical sensor which required some refactoring of the driver and parsing of i2c transfer. Sensor data is converted by the scaling value from percent to IIO_CONCENTRATION. Signed-off-by:
-
Matt Ranostay authored
Add modifier IIO_MOD_O2 for O2 concentration reporting Signed-off-by:
-
- 18 Aug, 2020 11 commits
-
-
Mauro Carvalho Chehab authored
The regulator driver needs it, as otherwise it will produce errors when creating vmlinux. Reported-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Link: https://lore.kernel.org/r/a287238bd0141aa68aae7d4cec4c1174a43b3e53.1597766680.git.mchehab+huawei@kernel.orgSigned-off-by:
-
Alex Dewar authored
Currently the module can only be test built on ARM, although it seems to build fine on x86. Change this to allow for broader test coverage. Signed-off-by:
Alex Dewar <alex.dewar90@gmail.com> Link: https://lore.kernel.org/r/20200818151133.583382-1-alex.dewar90@gmail.comSigned-off-by:
-
Mauro Carvalho Chehab authored
Add an entry for the SPMI, MFD and PMIC parts of the HiSilicon 6421v600 support. Signed-off-by:
-
Mauro Carvalho Chehab authored
Add documentation for the properties needed by the HiSilicon 6421v600 driver, and by the SPMI controller used to access the chipset. Signed-off-by:
-
Mauro Carvalho Chehab authored
It is clear that this driver is for PMIC. So, get rid of it at the compatible. Signed-off-by:
-
Mauro Carvalho Chehab authored
Add the chipset name at the compatible string, as other HiSilicon chipsets with SPMI bus might require something different. Signed-off-by:
-
Mauro Carvalho Chehab authored
Both irqnum and irqarray properties reflect the same thing: the number of bits and bytes for interrupts at this chipset. E. g.: irqnum = 8 x irqarray This can be seen by the way pending interrupts are handled: /* During probe time */ pmic->irqs = devm_kzalloc(dev, pmic->irqnum * sizeof(int), GFP_KERNEL); /* While handling IRQs */ for (i = 0; i < pmic->irqarray; i++) { pending = hi6421_spmi_pmic_read(pmic, (i + pmic->irq_addr)); pending &= 0xff; for_each_set_bit(offset, &pending, 8) generic_handle_irq(pmic->irqs[offset + i * 8]); } Going further, there are some logic at the driver which assumes that irqarray is 2: /* solve powerkey order */ if ((i == HISI_IRQ_KEY_NUM) && ((pending & HISI_IRQ_KEY_VALUE) == HISI_IRQ_KEY_VALUE)) { generic_handle_irq(pmic->irqs[HISI_IRQ_KEY_DOWN]); generic_handle_irq(pmic->irqs[HISI_IRQ_KEY_UP]); pending &= (~HISI_IRQ_KEY_VALUE); } As HISI_IRQ_KEY_DOWN and HISI_IRQ_KEY_UP are fixed values and don't depend on irqnum/irqarray. The IRQ addr and mask addr seem to be also fixed, based on some comments at the OF parsing code. So, get rid of them too, removing the of parsing function completely. Signed-off-by: -
Mauro Carvalho Chehab authored
Both the SPMI controller and the SPMI PMIC driver depends on the SPMI bus support. The dependency for the regulator is also wrong: it should depends on the SPMI version of the HiSilicon 6421, and not on the normal one. Signed-off-by:
-
Mauro Carvalho Chehab authored
Place the things that are needed to be able to move those drivers out of staging. Signed-off-by:
-
Mauro Carvalho Chehab authored
Do some code cleanup in order to make it cleaner for moving it out of staging in the future. Suggested-by:
-
Mauro Carvalho Chehab authored
Change the binding logic to ensure that the PMIC SPMI driver will run before the regulator code and add it to the building system. Signed-off-by:
-
