clang static analyzer reports this problem

init.c:739:8: warning: Called function pointer
  is null (null dereference)
        ret = adapter->if_ops.check_fw_status( ...
              ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In mwifiex_dnld_fw, there is an earlier check for check_fw_status(),
The check was introduced for usb support at the same time this
check in _mwifiex_fw_dpc() was made

	if (adapter->if_ops.dnld_fw) {
		ret = adapter->if_ops.dnld_fw(adapter, &fw);
	} else {
		ret = mwifiex_dnld_fw(adapter, &fw);
	}

And a dnld_fw function initialized as part the usb's
mwifiex_if_ops.

The other instances of mwifiex_if_ops for pci and sdio
both set check_fw_status.

So the first check is not needed and can be removed.

Fixes: 4daffe35 ("mwifiex: add support for Marvell USB8797 chipset")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906200548.18053-1-trix@redhat.com

Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com

This line is indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200905124758.GB183976@mwanda

Setting F2 block size to 128 bytes for BCM4329 allows to significantly
improve RX throughput on NVIDIA Tegra20. Before this change the throughput
was capped to 30 Mbit/s on Tegra, now throughput is at 40 Mbit/s, which is
a maximum throughput for the BCM4329 chip. The F2 block size is borrowed
from the downstream BCMDHD driver. The comment in the BCMDHD driver says
that 128B improves throughput and turns out that it works for the brcmfmac
as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-4-digetx@gmail.com

The chip ID was already printed out at the time when debug message about
the changed F2 watermark is printed, hence let's drop the unnecessary part
of the debug messages. This cleans code a tad and also allows to re-use
the F2 watermark debug messages by multiple chips.
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-3-digetx@gmail.com

This patch fixes SDHCI CRC errors during of RX throughput testing on
BCM4329 chip if SDIO BUS is clocked above 25MHz. In particular the
checksum problem is observed on NVIDIA Tegra20 SoCs. The good watermark
value is borrowed from downstream BCMDHD driver and it's matching to the
value that is already used for the BCM4339 chip, hence let's re-use it
for BCM4329.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-2-digetx@gmail.com

These variables only used in sdio.c, move them to .c file
can silence these warnings:

In file included from drivers/net/wireless/marvell/mwifiex//main.h:59:0,
                 from drivers/net/wireless/marvell/mwifiex//cfp.c:24:
drivers/net/wireless/marvell/mwifiex//sdio.h:705:41: warning: ‘mwifiex_sdio_sd8801’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8801 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:689:41: warning: ‘mwifiex_sdio_sd8987’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:674:41: warning: ‘mwifiex_sdio_sd8887’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:658:41: warning: ‘mwifiex_sdio_sd8997’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:642:41: warning: ‘mwifiex_sdio_sd8977’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:627:41: warning: ‘mwifiex_sdio_sd8897’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:612:41: warning: ‘mwifiex_sdio_sd8797’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:597:41: warning: ‘mwifiex_sdio_sd8787’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
                                         ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:582:41: warning: ‘mwifiex_sdio_sd8786’ defined but not used [-Wunused-const-variable=]
 static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
                                         ^~~~~~~~~~~~~~~~~~~
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902141155.30144-1-yuehaibing@huawei.com

In file included from drivers/net/wireless/marvell/mwifiex//cmdevt.c:26:0:
drivers/net/wireless/marvell/mwifiex//wmm.h:41:17: warning: ‘tos_to_tid_inv’ defined but not used [-Wunused-const-variable=]
 static const u8 tos_to_tid_inv[] = {
                 ^~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//wmm.h:34:18: warning: ‘mwifiex_1d_to_wmm_queue’ defined but not used [-Wunused-const-variable=]
 static const u16 mwifiex_1d_to_wmm_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
                  ^~~~~~~~~~~~~~~~~~~~~~~

move the variables definition to .c file, and leave declarations
in the header file to fix these warnings.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902140846.29024-1-yuehaibing@huawei.com

Remove function return type const in rtw8821c_get_swing_index().
This is unused, and unnecessary to be const.

All warnings (new ones prefixed by >>):

>> drivers/net/wireless/realtek/rtw88/rtw8821c.c:71:8: warning: type
qualifiers ignored on function return type [-Wignored-qualifiers]
       71 | static const u8 rtw8821c_get_swing_index(struct rtw_dev *rtwdev)
          |        ^~~~~

Fixes: f745eb9c ("rtw88: 8821c: Add 8821CE to Kconfig and Makefile")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902053402.12839-1-yhchuang@realtek.com

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901173603.GA2701@embeddedor

A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:

drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
        host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
                                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
        (((type) & 0x000f) << 12);                  }
                                                    ^

This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.

Fixes: 5e6e3a92 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1146Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com

A definition of this macro was kept until all drivers had been converted.
It can now be deleted.

This change also renames _rtl_dbg_trace() to _rtl_dbg_out().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831185046.30307-1-Larry.Finger@lwfinger.net

Change the misleading macro name to one that is more descriptive for
rtl8821ae. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831184536.29950-1-Larry.Finger@lwfinger.net

There is no caller in tree.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829115924.7572-1-yuehaibing@huawei.com

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9218:18: warning: ‘papd_cal_scalars_tbl_core1_rev3’ defined but not used [-Wunused-const-variable=]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9151:18: warning: ‘papd_comp_epsilon_tbl_core1_rev3’ defined but not used [-Wunused-const-variable=]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9084:18: warning: ‘papd_cal_scalars_tbl_core0_rev3’ defined but not used [-Wunused-const-variable=]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9017:18: warning: ‘papd_comp_epsilon_tbl_core0_rev3’ defined but not used [-Wunused-const-variable=]

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-31-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_lcn.c:1510:33: warning: ‘dot11lcnphytbl_rx_gain_info_rev1’ defined but not used [-Wunused-const-variable=]

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-30-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_spurwar_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:19036:6: warning: variable ‘tempval’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_tempsense_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:21983:28: warning: variable ‘RfctrlMiscReg6_save’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_rssi_compute_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:22986:6: warning: variable ‘phyRx0_l’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_runsamples_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23101:6: warning: variable ‘lpf_bw_ctl_miscreg4’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23100:50: warning: variable ‘lpf_bw_ctl_miscreg3’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_iqcal_gainparams_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23406:6: warning: variable ‘idx’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a2_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24707:7: warning: variable ‘phy_a6’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a3_nphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24999:7: warning: variable ‘phy_a11’ set but not used [-Wunused-but-set-variable]

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-29-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:11:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_rx_iq_cal’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1366:29: warning: variable ‘RFOverride0_old’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_radio_2064_channel_tune_4313’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:21: warning: variable ‘qFvco’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:14: warning: variable ‘qFref’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:6: warning: variable ‘qFxtal’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_idle_tssi_est’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2856:6: warning: variable ‘idleTssi’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_tx_iqlo_soft_cal_full’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:53: warning: variable ‘locc4’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:46: warning: variable ‘locc3’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:39: warning: variable ‘locc2’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:32: warning: variable ‘iqcc0’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_periodic_cal’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4196:6: warning: variable ‘rx_iqcomp_sz’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4195:33: warning: variable ‘rx_iqcomp’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4194:16: warning: variable ‘full_cal’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_phy_txpwr_srom_read_lcnphy’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4919:7: warning: variable ‘opo’ set but not used [-Wunused-but-set-variable]

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-28-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/intersil/prism54/isl_ioctl.c: In function ‘prism54_update_stats’:
 drivers/net/wireless/intersil/prism54/isl_ioctl.c:166:6: warning: variable ‘j’ set but not used [-Wunused-but-set-variable]

Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aurelien Alleaume <slts@free.fr>
Cc: Valerio Riedel <hvr@gnu.org>
Cc: "Luis R. Rodriguez" <mcgrof@ruslug.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-24-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/rsi/rsi_91x_sdio_ops.c:24: warning: Incorrect use of kernel-doc format:  * rsi_sdio_master_access_msword() - This function sets the AHB master access
 drivers/net/wireless/rsi/rsi_91x_sdio_ops.c:32: warning: Function parameter or member 'adapter' not described in 'rsi_sdio_master_access_msword'
 drivers/net/wireless/rsi/rsi_91x_sdio_ops.c:32: warning: Function parameter or member 'ms_word' not described in 'rsi_sdio_master_access_msword'

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-23-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtw88/debug.c: In function ‘rtw_debug_get_mac_page’:
 drivers/net/wireless/realtek/rtw88/debug.c:430:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtw88/debug.c: In function ‘rtw_debug_get_bb_page’:
 drivers/net/wireless/realtek/rtw88/debug.c:450:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]

Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-22-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/wl3501_cs.c:57:
 drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'reg_domain' not described in 'iw_valid_channel'
 drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'channel' not described in 'iw_valid_channel'
 drivers/net/wireless/wl3501_cs.c:162: warning: Function parameter or member 'reg_domain' not described in 'iw_default_channel'
 drivers/net/wireless/wl3501_cs.c:248: warning: Function parameter or member 'this' not described in 'wl3501_set_to_wla'
 drivers/net/wireless/wl3501_cs.c:270: warning: Function parameter or member 'this' not described in 'wl3501_get_from_wla'
 drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'this' not described in 'wl3501_send_pkt'
 drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'data' not described in 'wl3501_send_pkt'
 drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'len' not described in 'wl3501_send_pkt'
 drivers/net/wireless/wl3501_cs.c:729: warning: Function parameter or member 'this' not described in 'wl3501_block_interrupt'
 drivers/net/wireless/wl3501_cs.c:746: warning: Function parameter or member 'this' not described in 'wl3501_unblock_interrupt'
 drivers/net/wireless/wl3501_cs.c:1124: warning: Function parameter or member 'irq' not described in 'wl3501_interrupt'
 drivers/net/wireless/wl3501_cs.c:1124: warning: Function parameter or member 'dev_id' not described in 'wl3501_interrupt'
 drivers/net/wireless/wl3501_cs.c:1257: warning: Function parameter or member 'dev' not described in 'wl3501_reset'
 drivers/net/wireless/wl3501_cs.c:1420: warning: Function parameter or member 'link' not described in 'wl3501_detach'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Fox Chen <mhchen@golf.ccl.itri.org.tw>
Cc: de Melo <acme@conectiva.com.br>
Cc: Gustavo Niemeyer <niemeyer@conectiva.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-21-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/intersil/hostap/hostap_cs.c:196:
 drivers/net/wireless/intersil/hostap/hostap_hw.c: In function ‘prism2_tx_80211’:
 drivers/net/wireless/intersil/hostap/hostap_hw.c:1806:18: warning: variable ‘fc’ set but not used [-Wunused-but-set-variable]
 1806 | u16 tx_control, fc;
 | ^~
 In file included from drivers/net/wireless/intersil/hostap/hostap_plx.c:264:
 drivers/net/wireless/intersil/hostap/hostap_hw.c: In function ‘prism2_tx_80211’:
 drivers/net/wireless/intersil/hostap/hostap_hw.c:1806:18: warning: variable ‘fc’ set but not used [-Wunused-but-set-variable]
 1806 | u16 tx_control, fc;
 | ^~
 In file included from drivers/net/wireless/intersil/hostap/hostap_pci.c:221:
 drivers/net/wireless/intersil/hostap/hostap_hw.c: In function ‘prism2_tx_80211’:
 drivers/net/wireless/intersil/hostap/hostap_hw.c:1806:18: warning: variable ‘fc’ set but not used [-Wunused-but-set-variable]
 1806 | u16 tx_control, fc;
 | ^~

Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-20-lee.jones@linaro.org

- File headers do not make for good kernel-doc candidates
 - Kernel-doc header lines should start with " *"
 - Fix doc-rot issue

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/rsi/rsi_91x_sdio.c:25: warning: cannot understand function prototype: 'u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; '
 drivers/net/wireless/rsi/rsi_91x_sdio.c:802: warning: bad line:                                    from the device.
 drivers/net/wireless/rsi/rsi_91x_sdio.c:842: warning: Function parameter or member 'pfunction' not described in 'rsi_init_sdio_interface'
 drivers/net/wireless/rsi/rsi_91x_sdio.c:842: warning: Excess function parameter 'pkt' description in 'rsi_init_sdio_interface'

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-17-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-16-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'name' not described in 'brcmf_fws_mac_descriptor'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'requested_packet' not described in 'brcmf_fws_mac_descriptor'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'suppr_transit_count' not described in 'brcmf_fws_mac_descriptor'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'send_tim_signal' not described in 'brcmf_fws_mac_descriptor'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_pending_bmp' not described in 'brcmf_fws_mac_descriptor'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_lastreported_bmp' not described in 'brcmf_fws_mac_descriptor'

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-14-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Function parameter or member 'status' not described in 'zd_rx_rate'
 drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Excess function parameter 'rx_status' description in 'zd_rx_rate'

Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-12-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Function parameter or member 'hw' not described in 'zd_mac_tx_status'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Function parameter or member 'skb' not described in 'zd_mac_tx_status'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Function parameter or member 'tx_status' not described in 'zd_mac_tx_status'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Excess function parameter 'flags' description in 'zd_mac_tx_status'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:487: warning: Function parameter or member 'urb' not described in 'zd_mac_tx_failed'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:487: warning: Excess function parameter 'dev' description in 'zd_mac_tx_failed'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:927: warning: Function parameter or member 'hw' not described in 'zd_op_tx'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:927: warning: Excess function parameter 'dev' description in 'zd_op_tx'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:963: warning: Function parameter or member 'hw' not described in 'filter_ack'
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c:963: warning: Excess function parameter 'dev' description in 'filter_ack'

Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Michael Wu <flamingice@sourmilk.net>
Cc: "Luis R. Rodriguez" <mcgrof@winlab.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-11-lee.jones@linaro.org

Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Function parameter or member 'rx_frame' not described in 'zd_rx_rate'
 drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Function parameter or member 'status' not described in 'zd_rx_rate'

Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-10-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:12:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c: In function ‘wlc_phy_upd_env_txpwr_rate_limits’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:1516:11: warning: variable ‘vbat’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:1516:5: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable]

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-9-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:434: warning: Function parameter or member 'upriv' not described in 'ezusb_req_queue_run'
 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'req' not described in 'ezusb_fill_req'
 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'length' not described in 'ezusb_fill_req'
 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'rid' not described in 'ezusb_fill_req'
 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'data' not described in 'ezusb_fill_req'
 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'frame_type' not described in 'ezusb_fill_req'
 drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'reply_count' not described in 'ezusb_fill_req'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-8-lee.jones@linaro.org

Most likely caused by doc-rot.

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2048: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2048: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-7-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/intel/iwlegacy/3945.c:104: warning: Function parameter or member 'il' not described in 'il3945_disable_events'
 drivers/net/wireless/intel/iwlegacy/3945.c:273: warning: Function parameter or member 'il' not described in 'il3945_tx_queue_reclaim'
 drivers/net/wireless/intel/iwlegacy/3945.c:273: warning: Function parameter or member 'txq_id' not described in 'il3945_tx_queue_reclaim'
 drivers/net/wireless/intel/iwlegacy/3945.c:273: warning: Function parameter or member 'idx' not described in 'il3945_tx_queue_reclaim'
 drivers/net/wireless/intel/iwlegacy/3945.c:299: warning: Function parameter or member 'il' not described in 'il3945_hdl_tx'
 drivers/net/wireless/intel/iwlegacy/3945.c:299: warning: Function parameter or member 'rxb' not described in 'il3945_hdl_tx'
 drivers/net/wireless/intel/iwlegacy/3945.c:637: warning: Function parameter or member 'il' not described in 'il3945_hw_txq_free_tfd'
 drivers/net/wireless/intel/iwlegacy/3945.c:637: warning: Function parameter or member 'txq' not described in 'il3945_hw_txq_free_tfd'
 drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'il' not described in 'il3945_hw_build_tx_cmd_rate'
 drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'cmd' not described in 'il3945_hw_build_tx_cmd_rate'
 drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'info' not described in 'il3945_hw_build_tx_cmd_rate'
 drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'hdr' not described in 'il3945_hw_build_tx_cmd_rate'
 drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'sta_id' not described in 'il3945_hw_build_tx_cmd_rate'
 drivers/net/wireless/intel/iwlegacy/3945.c:838: warning: Function parameter or member 'il' not described in 'il3945_txq_ctx_reset'
 drivers/net/wireless/intel/iwlegacy/3945.c:1003: warning: Function parameter or member 'il' not described in 'il3945_hw_txq_ctx_free'
 drivers/net/wireless/intel/iwlegacy/3945.c:1044: warning: Function parameter or member 'new_reading' not described in 'il3945_hw_reg_adjust_power_by_temp'
 drivers/net/wireless/intel/iwlegacy/3945.c:1044: warning: Function parameter or member 'old_reading' not described in 'il3945_hw_reg_adjust_power_by_temp'
 drivers/net/wireless/intel/iwlegacy/3945.c:1053: warning: Function parameter or member 'temperature' not described in 'il3945_hw_reg_temp_out_of_range'
 drivers/net/wireless/intel/iwlegacy/3945.c:1069: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_txpower_get_temperature'
 drivers/net/wireless/intel/iwlegacy/3945.c:1107: warning: Function parameter or member 'il' not described in 'il3945_is_temp_calib_needed'
 drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_set_scan_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'scan_tbl_idx' not described in 'il3945_hw_reg_set_scan_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'rate_idx' not described in 'il3945_hw_reg_set_scan_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'clip_pwrs' not described in 'il3945_hw_reg_set_scan_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'ch_info' not described in 'il3945_hw_reg_set_scan_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'band_idx' not described in 'il3945_hw_reg_set_scan_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1383: warning: Function parameter or member 'il' not described in 'il3945_send_tx_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1460: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_set_new_power'
 drivers/net/wireless/intel/iwlegacy/3945.c:1522: warning: Function parameter or member 'ch_info' not described in 'il3945_hw_reg_get_ch_txpower_limit'
 drivers/net/wireless/intel/iwlegacy/3945.c:1552: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_comp_txpower_temp'
 drivers/net/wireless/intel/iwlegacy/3945.c:1712: warning: Function parameter or member 'il' not described in 'il3945_commit_rxon'
 drivers/net/wireless/intel/iwlegacy/3945.c:1845: warning: Function parameter or member 'il' not described in 'il3945_reg_txpower_periodic'
 drivers/net/wireless/intel/iwlegacy/3945.c:1889: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_get_ch_grp_idx'
 drivers/net/wireless/intel/iwlegacy/3945.c:1889: warning: Function parameter or member 'ch_info' not described in 'il3945_hw_reg_get_ch_grp_idx'
 drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_get_matched_power_idx'
 drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'requested_power' not described in 'il3945_hw_reg_get_matched_power_idx'
 drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'setting_idx' not described in 'il3945_hw_reg_get_matched_power_idx'
 drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'new_idx' not described in 'il3945_hw_reg_get_matched_power_idx'
 drivers/net/wireless/intel/iwlegacy/3945.c:2055: warning: Function parameter or member 'il' not described in 'il3945_txpower_set_from_eeprom'
 drivers/net/wireless/intel/iwlegacy/3945.c:2313: warning: Function parameter or member 'il' not described in 'il3945_init_hw_rate_table'

Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-6-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/intel/iwlegacy/3945-rs.c:136: warning: Function parameter or member 'rs_sta' not described in 'il3945_rate_scale_flush_wins'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'rs_sta' not described in 'il3945_collect_tx_data'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'win' not described in 'il3945_collect_tx_data'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'success' not described in 'il3945_collect_tx_data'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'retries' not described in 'il3945_collect_tx_data'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'idx' not described in 'il3945_collect_tx_data'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'il_rate' not described in 'il3945_rs_tx_status'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'sband' not described in 'il3945_rs_tx_status'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'sta' not described in 'il3945_rs_tx_status'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'il_sta' not described in 'il3945_rs_tx_status'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'skb' not described in 'il3945_rs_tx_status'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'il_r' not described in 'il3945_rs_get_rate'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'sta' not described in 'il3945_rs_get_rate'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'il_sta' not described in 'il3945_rs_get_rate'
 drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'txrc' not described in 'il3945_rs_get_rate'

Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-5-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/intel/iwlegacy/3945-mac.c:821: warning: Function parameter or member 'il' not described in 'il3945_setup_handlers'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:915: warning: Function parameter or member 'il' not described in 'il3945_dma_addr2rbd_ptr'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:915: warning: Function parameter or member 'dma_addr' not described in 'il3945_dma_addr2rbd_ptr'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:932: warning: Function parameter or member 'il' not described in 'il3945_rx_queue_restock'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:979: warning: Function parameter or member 'il' not described in 'il3945_rx_allocate'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:979: warning: Function parameter or member 'priority' not described in 'il3945_rx_allocate'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1179: warning: Function parameter or member 'il' not described in 'il3945_rx_handle'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1663: warning: Function parameter or member 'il' not described in 'il3945_verify_inst_full'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1663: warning: Function parameter or member 'image' not described in 'il3945_verify_inst_full'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1663: warning: Function parameter or member 'len' not described in 'il3945_verify_inst_full'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1703: warning: Function parameter or member 'il' not described in 'il3945_verify_inst_sparse'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1703: warning: Function parameter or member 'image' not described in 'il3945_verify_inst_sparse'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1703: warning: Function parameter or member 'len' not described in 'il3945_verify_inst_sparse'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1739: warning: Function parameter or member 'il' not described in 'il3945_verify_ucode'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:1821: warning: Function parameter or member 'il' not described in 'il3945_read_ucode'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:2061: warning: Function parameter or member 'il' not described in 'il3945_set_ucode_ptrs'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:2093: warning: Function parameter or member 'il' not described in 'il3945_init_alive_start'
 drivers/net/wireless/intel/iwlegacy/3945-mac.c:2135: warning: Function parameter or member 'il' not described in 'il3945_alive_start'

Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-4-lee.jones@linaro.org

Fixes the following W=1 kernel build warning(s):

 from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:850:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
 drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1027:20: warning: variable ‘scb_ampdu’ set but not used [-Wunused-but-set-variable]

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-3-lee.jones@linaro.org

Saves on 10's of complains about 'defined but not used' variables.

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/marvell/mwifiex/main.h:57,
 from drivers/net/wireless/marvell/mwifiex/main.c:22:
 drivers/net/wireless/marvell/mwifiex/pcie.h:310:41: warning: ‘mwifiex_pcie8997’ defined but not used [-Wunused-const-variable=]
 310 | static const struct mwifiex_pcie_device mwifiex_pcie8997 = {
 | ^~~~~~~~~~~~~~~~
 drivers/net/wireless/marvell/mwifiex/pcie.h:300:41: warning: ‘mwifiex_pcie8897’ defined but not used [-Wunused-const-variable=]
 300 | static const struct mwifiex_pcie_device mwifiex_pcie8897 = {
 | ^~~~~~~~~~~~~~~~
 drivers/net/wireless/marvell/mwifiex/pcie.h:292:41: warning: ‘mwifiex_pcie8766’ defined but not used [-Wunused-const-variable=]
 292 | static const struct mwifiex_pcie_device mwifiex_pcie8766 = {
 | ^~~~~~~~~~~~~~~~

 NB: Repeats 10's of times - snipped for brevity.

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-2-lee.jones@linaro.org

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1].

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821061807.GA8412@embeddedor

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'rtl8180_init_rx_ring()' and
'rtl8180_init_tx_ring()' GFP_KERNEL can be used because both functions are
called from 'rtl8180_start()', which is a .start function (see struct
ieee80211_ops)
.start function can sleep, as explicitly stated in include/net/mac80211.h.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819210852.120826-1-christophe.jaillet@wanadoo.fr

In p54p_tx(), skb->data is mapped to streaming DMA on line 337:
  mapping = pci_map_single(..., skb->data, ...);

Then skb->data is accessed on line 349:
  desc->device_addr = ((struct p54_hdr *)skb->data)->req_id;

This access may cause data inconsistency between CPU cache and hardware.

To fix this problem, ((struct p54_hdr *)skb->data)->req_id is stored in
a local variable before DMA mapping, and then the driver accesses this
local variable instead of skb->data.

Cc: <stable@vger.kernel.org>
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802132949.26788-1-baijiaju@tsinghua.edu.cn