- 27 Jun, 2011 30 commits
-
-
Geert Uytterhoeven authored
m68k allmodconfig: drivers/bcma/main.c: In function ‘bcma_release_core_dev’: drivers/bcma/main.c:68: error: implicit declaration of function ‘kfree’ Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> -- http://kisskb.ellerman.id.au/kisskb/buildresult/4243344/ drivers/bcma/main.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Sergei Shtylyov authored
Commit ff938e43 (net: use pci_dev->revision, again) already converted this driver to using the 'revision' field of 'struct pci_dev' but commit 084dd791 (iwlagn: move PCI related operations from probe and remove to PCI layer) has again added the code to read the PCI revision ID register... Signed-off-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Dan Carpenter authored
Prior to a5ffddb7 "mwifiex: remove casts of void pointers" the code assumed that the data_buf parameter could be a NULL pointer. The patch preserved some NULL checks but not consistently, so there was a potential for NULL dereferences and it changed the behavior. This patch restores the original behavior. Signed-off-by:
Dan Carpenter <error27@gmail.com> Acked-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Rajkumar Manoharan authored
The received tx status of aggregated frame without BlockAck may cause deaf state in AR5416 cards. So the driver does a reset to recover. When this happens, we release the pcu_lock before doing a reset as ath_rest acquires pcu_lock. This is ugly and also not atomic. Fixing this addresses the TX DMA failure also. ath_tx_complete_aggr can be called from different paths which takes different variants of spin_lock. This patch also addresses the following warning. WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50() Call Trace: <IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0 [<ffffffff8104be85>] warn_slowpath_null+0x15/0x20 [<ffffffff8105915e>] del_timer_sync+0x4e/0x50 [<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k] [<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30 [<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k] Signed-off-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Stanislaw Gruszka authored
priv->bus.bus_specific pointer is used after priv structures was freed, in iwl_pci_remove(), what make ugly rmmod crash. This bug was introduced by current pci changes. On the way remove fake check, if prober error code is returned from .probe() function, .remove() will never be called be null drvdata. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Joe Perches authored
Signed-off-by:
Joe Perches <joe@perches.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Paul Stewart authored
Do not send DS Channel parameter for directed probe requests in order to maximize the chance that we get a response. Some badly-behaved APs don't respond when this parameter is included. Signed-off-by:
Paul Stewart <pstew@chromium.org> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Sergei Shtylyov authored
The bus scan code reads PCI revision ID from the PCI configuration register while it's already stored by PCI subsystem in the 'revision' field of 'struct pci_dev'... Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Cc: muddin@qca.qualcomm.com Signed-off-by:
-
Rajkumar Manoharan authored
The edma based (AR9003 family) chips update tx status descriptors in a common ring buffer for all transmitted frames. Whenever tx interrupt is raised, the descriptors are processed and tx status index is moved. The complete tx stauts ring are updated with beacons tx status when there are no data frames to be sent for a period of time. In this state, transmitting data frames causes the driver to wait for the tx status on an incorrect tx status index though the status was updated by hw properly. The driver detects this condition as a h/w hang and does unnecessary chip resets. This issue was orginally reported in adhoc mode while sending frames after an idle time. Signed-off-by:
-
Arik Nemtsov authored
When forming a Rx BA session, sometimes the ADDBA response gets lost. This leads to a situation where the session is configured locally, but doesn't exist on the remote side. Subsequent ADDBA requests are declined by mac80211. Fix this by assuming the session state of the initiator is the correct one. When receiving an unexpected ADDBA request on a TID with an active Rx BA session, delete the existing one and establish a new session. Signed-off-by:
Arik Nemtsov <arik@wizery.com> Acked-by:
-
Randy Dunlap authored
Recent changes to hci_core.c use crypto interfaces, so select CRYPTO to make sure that those interfaces are present. Fixes these build errors when CRYPTO is not enabled: net/built-in.o: In function `hci_register_dev': (.text+0x4cf86): undefined reference to `crypto_alloc_base' net/built-in.o: In function `hci_unregister_dev': (.text+0x4f912): undefined reference to `crypto_destroy_tfm' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Johannes Berg authored
Advertise only user-requested bitrates in a HW scan. Note that the hw_scan API doesn't currently have a way of asking for a specific probe request bitrate, so we might end up using a bitrate that we don't advertise as supported. I'll fix that later. Also add a hexdump printk to hwsim to verify this. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
Move all that mac80211 has into the generic ieee80211.h header file and use them. At the same time move them from mask+shift to just bits and rename them for consistent names. Signed-off-by:
-
Hauke Mehrtens authored
This fix was done according to si_clock_rate function in broadcom siutils.c Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
Chaoming Li authored
Set up Kconfig and Makefile for new driver for RTL8192DE. Signed-off-by:
Chaoming_Li <chaoming_li@realsil.com.cn> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Larry Finger authored
These patches allow compilation of rtlwifi, rtl8192c_common, rtl8192ce, rtl8192cu and rtl8192se to compile after rtl8192de was added. Signed-off-by:
-
Chaoming Li authored
Merge routines trx.c and trx.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines table.c and table.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines sw.c and sw.h for RTL8192SE. Signed-off-by:
-
Chaoming Li authored
Merge routines rf.c and rf.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines reg.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines phy.c and phy.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines led.c and led.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines hw.c and hw.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines fw.c and fw.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Merge routines dm.c and dm.h for RTL8192DE. Signed-off-by:
-
Chaoming Li authored
Introduce routine def.h for rtl8192de. Signed-off-by:
-
John W. Linville authored
Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
-
- 24 Jun, 2011 6 commits
-
-
Stephen Rothwell authored
net/bluetooth/smp.c: In function 'smp_e': net/bluetooth/smp.c:49:21: error: storage size of 'sg' isn't known net/bluetooth/smp.c:67:2: error: implicit declaration of function 'sg_init_one' net/bluetooth/smp.c:49:21: warning: unused variable 'sg' Caused by commit d22ef0bc ("Bluetooth: Add LE SMP Cryptoolbox functions"). Missing include file, presumably. This batch has been in the bluetooth tree since June 14, so it may have been exposed by the removal of linux/mm.h from netdevice.h ... Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Johannes Berg authored
P2P interfaces must not use CCK rates, only OFDM rates are allowed. To set this up, we need to set up the broadcast station to start with 6M instead of starting with 1M. Since the interface type can change, also reset the broadcast station when RXON changes. This will affect beacons as well. Signed-off-by:
-
Johannes Berg authored
Use the rate that mac80211 requested to fill the uCode TX command for the beacon. Unfortunately, the uCode is (currently?) ignoring it, but now at least fill it properly. Signed-off-by:
-
Johannes Berg authored
We've infrequently seen timeouts, make the wait time match the windows driver; hopefully our driver is just too impatient. Signed-off-by:
-
Johannes Berg authored
When we stop the device while a command is in flight that uses multiple TBs, we can leak the DMA buffers for the second and higher TBs. Fix this by using iwlagn_unmap_tfd() as we do when we normally recover the entry. Signed-off-by:
-
Johannes Berg authored
Simplify the code and use SIMPLE_DEV_PM_OPS to define iwl_dev_pm_ops instead of doing the same thing manually. Signed-off-by:
-
- 22 Jun, 2011 4 commits
-
-
Hauke Mehrtens authored
Two functions in ssb are using register_pci_controller() which is __devinit. The functions ssb_pcicore_init_hostmode() and ssb_gige_probe() should also be __devinit. This fixes the following warning: WARNING: vmlinux.o(.text+0x2727b8): Section mismatch in reference from the function ssb_pcicore_init_hostmode() to the function .devinit.text:register_pci_controller() The function ssb_pcicore_init_hostmode() references the function __devinit register_pci_controller(). This is often because ssb_pcicore_init_hostmode lacks a __devinit annotation or the annotation of register_pci_controller is wrong. WARNING: vmlinux.o(.text+0x273398): Section mismatch in reference from the function ssb_gige_probe() to the function .devinit.text:register_pci_controller() The function ssb_gige_probe() references the function __devinit register_pci_controller(). This is often because ssb_gige_probe lacks a __devinit annotation or the annotation of register_pci_controller is wrong. Reported-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
-
Gabor Juhos authored
The patch adds a callback to ath9k_platform_data. If the callback is provided by the platform code, then it can be used to hard reset the WMAC device. The callback is required for doing a hard reset of the AR9330 chips to get them working again after a hang. Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
-
