- 02 Feb, 2015 1 commit
-
-
Luis Henriques authored
Signed-off-by:Luis Henriques <luis.henriques@canonical.com>
-
- 26 Jan, 2015 3 commits
-
-
Geert Uytterhoeven authored
commit b0ddb319 upstream. The sh73a0 INTC can't mask interrupts properly most likely due to a hardware bug. Set the .control_parent flag to delegate masking to the parent interrupt controller, like was already done for irqpin1. Without this, accessing the three-axis digital accelerometer ADXL345 on kzm9g through /dev/input/event1 causes an interrupt storm, which requires a power-cycle to recover from. This was inspired by a patch for arch/arm/boot/dts/sh73a0.dtsi from Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Fixes: 341eb546 ("ARM: shmobile: INTC External IRQ pin driver on sh73a0") Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Mugunthan V N authored
commit 69d2626f upstream. 64KiB is allocated for qspi dtb partition which is not sufficient, so updating the partition table size to 512KiB for device tree partition. This also aligns the QSPI partition definitions between kernel and U-Boot. Fixes: dc2dd5b8 ("ARM: dts: dra7: Add qspi device") Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
David Vrabel authored
commit dbdd7476 upstream. This reverts commit 2c3fc8d2. This commit broke on x86 PV because entries in the generic SWIOTLB are indexed using (pseudo-)physical address not DMA address and these are not the same in a x86 PV guest. Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Reviewed-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Cc: Ian Campbell <Ian.Campbell@citrix.com> Signed-off-by:
-
- 23 Jan, 2015 3 commits
-
-
Chris Wilson authored
commit c4d69da1 upstream. Running igt, I was encountering the invalid TLB bug on my 845g, despite that it was using the CS workaround. Examining the w/a buffer in the error state, showed that the copy from the user batch into the workaround itself was suffering from the invalid TLB bug (the first cacheline was broken with the first two words reversed). Time to try a fresh approach. This extends the workaround to write into each page of our scratch buffer in order to overflow the TLB and evict the invalid entries. This could be refined to only do so after we update the GTT, but for simplicity, we do it before each batch. I suspect this supersedes our current workaround, but for safety keep doing both. v2: The magic number shall be 2. This doesn't conclusively prove that it is the mythical TLB bug we've been trying to workaround for so long, that it requires touching a number of pages to prevent the corruption indicates to me that it is TLB related, but the corruption (the reversed cacheline) is more subtle than a TLB bug, where we would expect it to read the wrong page entirely. Oh well, it prevents a reliable hang for me and so probably for others as well. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Alexander Y. Fomichev authored
commit 7ce64c79 upstream. __netdev_adjacent_dev_insert may add adjust device of different net namespace, without proper check it leads to emergence of broken sysfs links from/to devices in another namespace. Fix: rewrite netdev_adjacent_is_neigh_list macro as a function, move net_eq check into netdev_adjacent_is_neigh_list. (thanks David) related to: 4c75431aSigned-off-by:
Alexander Fomichev <git.user@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Miquel van Smoorenburg <mikevs@xs4all.net> Signed-off-by:
-
Alexander Y. Fomichev authored
commit 4c75431a upstream. Code manipulating sysfs symlinks on adjacent net_devices(s) currently doesn't take into account that devices potentially belong to different namespaces. This patch trying to fix an issue as follows: - check for net_ns before creating / deleting symlink. for now only netdev_adjacent_rename_links and __netdev_adjacent_dev_remove are affected, afaics __netdev_adjacent_dev_insert implies both net_devs belong to the same namespace. - Drop all existing symlinks to / from all adj_devs before switching namespace and recreate them just after. Signed-off-by:
-
- 22 Jan, 2015 33 commits
-
-
Hannes Reinecke authored
commit 6375f890 upstream. The SCSI command tag is set to the tag assigned from the block layer, not the SCSI-II tag message. So we need to convert it into the correct SCSI-II tag message based on the device flags, not the tag value itself. Signed-off-by:
Hannes Reinecke <hare@suse.de> Reviewed-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [ luis: backported to 3.16: - adjusted context, as commit 506787a2 ("tcm_loop: Fix wrong I_T nexus association") had already been applied to 3.16 ] Signed-off-by:
-
Tomeu Vizoso authored
commit 10cdfe54 upstream. As __clk_release could call kfree on clk and then we wouldn't have a safe way of getting the module that owns the clock. Signed-off-by:
Tomeu Vizoso <tomeu.vizoso@collabora.com> Fixes: fcb0ee6a ("clk: Implement clk_unregister") Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Michael Turquette <mturquette@linaro.org> Signed-off-by:
-
Tyler Baker authored
commit 41544f9f upstream. Call spin_lock_init() before the spinlocks are used, both in early init and probe functions preventing a lockdep splat. I have been observing lockdep complaining [1] during boot on my a80 optimus [2] when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat, and has been tested on a few other sunxi platforms without issue. [1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html [2] http://kernelci.org/boot/?a80-optimusSigned-off-by:
Tyler Baker <tyler.baker@linaro.org> Acked-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Kevin Hilman <khilman@linaro.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 237d28db upstream. If the function graph tracer traces a jprobe callback, the system will crash. This can easily be demonstrated by compiling the jprobe sample module that is in the kernel tree, loading it and running the function graph tracer. # modprobe jprobe_example.ko # echo function_graph > /sys/kernel/debug/tracing/current_tracer # ls The first two commands end up in a nice crash after the first fork. (do_fork has a jprobe attached to it, so "ls" just triggers that fork) The problem is caused by the jprobe_return() that all jprobe callbacks must end with. The way jprobes works is that the function a jprobe is attached to has a breakpoint placed at the start of it (or it uses ftrace if fentry is supported). The breakpoint handler (or ftrace callback) will copy the stack frame and change the ip address to return to the jprobe handler instead of the function. The jprobe handler must end with jprobe_return() which swaps the stack and does an int3 (breakpoint). This breakpoint handler will then put back the saved stack frame, simulate the instruction at the beginning of the function it added a breakpoint to, and then continue on. For function tracing to work, it hijakes the return address from the stack frame, and replaces it with a hook function that will trace the end of the call. This hook function will restore the return address of the function call. If the function tracer traces the jprobe handler, the hook function for that handler will not be called, and its saved return address will be used for the next function. This will result in a kernel crash. To solve this, pause function tracing before the jprobe handler is called and unpause it before it returns back to the function it probed. Some other updates: Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the code look a bit cleaner and easier to understand (various tries to fix this bug required this change). Note, if fentry is being used, jprobes will change the ip address before the function graph tracer runs and it will not be able to trace the function that the jprobe is probing. Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.orgAcked-by:
Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Amit Virdi authored
commit 39e60635 upstream. DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This means, the max TRBs that can be submitted for an EP is fixed to 32. Since the request queue for an EP is a linked list, any number of requests can be queued to it by the gadget layer. However, the dwc3 driver must not submit TRBs more than the pool it has created for. This limit wasn't respected when SG was used resulting in submitting more than the max TRBs, eventually leading to non-transfer of the TRBs submitted over the max limit. Root cause: When SG is used, there are two loops iterating to prepare TRBs: - Outer loop over the request_list - Inner loop over the SG list The code was missing break to get out of the outer loop. Fixes: eeb720fb (usb: dwc3: gadget: add support for SG lists) Signed-off-by:
Amit Virdi <amit.virdi@st.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Amit Virdi authored
commit ec512fb8 upstream. When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3 request (dwc3_request). So while preparing TRBs, the 'last' flag should be set only when it is the last TRB being prepared from the last dwc3_request entry. The current implementation uses list_is_last to check if the dwc3_request is the last entry from the request_list. However, list_is_last returns false for the last entry too. This is because, while preparing the first TRB from a request, the function dwc3_prepare_one_trb modifies the request's next and prev pointers while moving the URB to req_queued. Hence, list_is_last always returns false no matter what. The correct way is not to access the modified pointers of dwc3_request but to use list_empty macro instead. Fixes: e5ba5ec8 (usb: dwc3: gadget: fix scatter gather implementation) Signed-off-by:
-
Mugunthan V N authored
commit 25906052 upstream. Since ALE table is a common resource for both the interfaces in Dual EMAC mode and while bringing up the second interface in cpsw_ndo_set_rx_mode() all the multicast entries added by the first interface is flushed out and only second interface multicast addresses are added. Fixing this by flushing multicast addresses based on dual EMAC port vlans which will not affect the other emac port multicast addresses. Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation) Signed-off-by:
-
Jisheng Zhang authored
commit b71e8ecd upstream. The "smemc" clock is removed on BG2Q SoCs. In fact, bit19 of clkenable register is for nfc. Current code use bit19 for non-exist "smemc" incorrectly, this prevents eMMC from working due to the sdhci's "core" clk is still gated. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Boris Brezillon authored
commit dca1a4b5 upstream. All slow clk users are not properly claiming it (get + prepare + enable) before using it. If all users properly claiming this clock release it, the clock is disabled, but faulty users still depends on it, and the system hangs. This fix prevents the slow clock from being disabled, and should solve the hanging issue, but offending drivers should be patched to properly claim this clock. Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Reported-by:
Bo Shen <voice.shen@atmel.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 2836766a upstream. Sleep in atomic context happened on Trats2 board after inserting or removing SD card because mmc_gpio_get_cd() was called under spin lock. Fix this by moving card detection earlier, before acquiring spin lock. The mmc_gpio_get_cd() call does not have to be protected by spin lock because it does not access any sdhci internal data. The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After moving it out side of spin lock it could theoretically race with driver removal but still there is no actual protection against manual card eject. Dmesg after inserting SD card: [ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511 [ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1 [ 41.677580] INFO: lockdep is turned off. [ 41.681486] irq event stamp: 61972 [ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c [ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54 [ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8 [ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114 [ 41.716206] Preemption disabled at:[< (null)>] (null) [ 41.721500] [ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883 [ 41.732111] Workqueue: kmmcd mmc_rescan [ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14) [ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc) [ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30) [ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58) [ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4) [ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268) [ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0) [ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78) [ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124) [ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64) [ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4) [ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4) [ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0) [ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104) [ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c) [ 42.038276] mmc0: new high speed SDHC card at address 1234 Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 94144a46 ("mmc: sdhci: add get_cd() implementation") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Thomas Petazzoni authored
commit aa8165f9 upstream. In commit 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller"), the sdhci-pxav3 driver was extended to include support for the SDHCI controller found in the Armada 38x processor. This mainly involved adding some MBus window related configuration. However, this configuration is currently done too early in ->probe(): it is done before clocks are enabled, while this configuration involves touching the registers of the controller, which will hang the SoC if the clock is disabled. It wasn't noticed until now because the bootloader typically leaves gatable clocks enabled, but in situations where we have a deferred probe (due to a CD GPIO that cannot be taken, for example), then the probe will be re-tried later, after a clock disable has been done in the exit path of the failed probe attempt of the device. This second probe() will hang the system due to the clock being disabled. This can for example be produced on Armada 385 GP, which has a CD GPIO connected to an I2C PCA9555. If the driver for the PCA9555 is not compiled into the kernel, then we will have the following sequence of events: 1. The SDHCI probes 2. It does the MBus configuration (which works, because the clock is left enabled by the bootloader) 3. It enables the clock 4. It tries to get the CD GPIO, which fails due to the driver being missing, so -EPROBE_DEFER is returned. 5. Before returning -EPROBE_DEFER, the driver cleans up what was done, which includes disabling the clock. 6. Later on, the SDHCI probe is tried again. 7. It does the MBus configuration, which hangs because the clock is no longer enabled. This commit does the obvious fix of doing the MBus configuration after the clock has been enabled by the driver. Fixes: 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Xiang Wang authored
commit 87d2163d upstream. Commit 0dcaa249 improved error handling of sdhci_add_host. However, "err_of_parse" and "err_cd_req" should be placed after "pm_runtime_disable(&pdev->dev)". Signed-off-by:
Xiang Wang <wangx@marvell.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Johan Hovold authored
commit 32a4bf2e upstream. Use tty kref to release the fake tty in usb_console_setup to avoid use after free if the underlying serial driver has acquired a reference. Note that using the tty destructor release_one_tty requires some more state to be initialised. Fixes: 4a90f09b ("tty: usb-serial krefs") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit d269d443 upstream. The USB console currently allocates a temporary fake tty which is used to pass terminal settings to the underlying serial driver. The tty struct is not fully initialised, something which can lead to a lockdep warning (or worse) if a serial driver tries to acquire a line-discipline reference: usbserial: USB Serial support registered for pl2303 pl2303 1-2.1:1.0: pl2303 converter detected usb 1-2.1: pl2303 converter now attached to ttyUSB0 INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 0 PID: 68 Comm: udevd Tainted: G W 3.18.0-rc5 #10 [<c0016f04>] (unwind_backtrace) from [<c0013978>] (show_stack+0x20/0x24) [<c0013978>] (show_stack) from [<c0449794>] (dump_stack+0x24/0x28) [<c0449794>] (dump_stack) from [<c006f730>] (__lock_acquire+0x1e50/0x2004) [<c006f730>] (__lock_acquire) from [<c0070128>] (lock_acquire+0xe4/0x18c) [<c0070128>] (lock_acquire) from [<c027c6f8>] (ldsem_down_read_trylock+0x78/0x90) [<c027c6f8>] (ldsem_down_read_trylock) from [<c027a1cc>] (tty_ldisc_ref+0x24/0x58) [<c027a1cc>] (tty_ldisc_ref) from [<c0340760>] (usb_serial_handle_dcd_change+0x48/0xe8) [<c0340760>] (usb_serial_handle_dcd_change) from [<bf000484>] (pl2303_read_int_callback+0x210/0x220 [pl2303]) [<bf000484>] (pl2303_read_int_callback [pl2303]) from [<c031624c>] (__usb_hcd_giveback_urb+0x80/0x140) [<c031624c>] (__usb_hcd_giveback_urb) from [<c0316fc0>] (usb_giveback_urb_bh+0x98/0xd4) [<c0316fc0>] (usb_giveback_urb_bh) from [<c0042e44>] (tasklet_hi_action+0x9c/0x108) [<c0042e44>] (tasklet_hi_action) from [<c0042380>] (__do_softirq+0x148/0x42c) [<c0042380>] (__do_softirq) from [<c00429cc>] (irq_exit+0xd8/0x114) [<c00429cc>] (irq_exit) from [<c007ae58>] (__handle_domain_irq+0x84/0xdc) [<c007ae58>] (__handle_domain_irq) from [<c000879c>] (omap_intc_handle_irq+0xd8/0xe0) [<c000879c>] (omap_intc_handle_irq) from [<c0014544>] (__irq_svc+0x44/0x7c) Exception stack(0xdf4e7f08 to 0xdf4e7f50) 7f00: debc0b80 df4e7f5c 00000000 00000000 debc0b80 be8da96c 7f20: 00000000 00000128 c000fc84 df4e6000 00000000 df4e7f94 00000004 df4e7f50 7f40: c038ebc0 c038d74c 600f0013 ffffffff [<c0014544>] (__irq_svc) from [<c038d74c>] (___sys_sendmsg.part.29+0x0/0x2e0) [<c038d74c>] (___sys_sendmsg.part.29) from [<c038ec08>] (SyS_sendmsg+0x18/0x1c) [<c038ec08>] (SyS_sendmsg) from [<c000fa00>] (ret_fast_syscall+0x0/0x48) console [ttyUSB0] enabled Fixes: 36697529 ("tty: Replace ldisc locking with ldisc_sem") Signed-off-by:
-
Songjun Wu authored
commit 5fb694f9 upstream. When unloading the module 'g_hid.ko', the urb request will be dequeued and the completion routine will be excuted. If there is no urb packet, the urb request will not be added to the endpoint queue and the completion routine pointer in urb request is NULL. Accessing to this NULL function pointer will cause the Oops issue reported below. Add the code to check if the urb request is in the endpoint queue or not. If the urb request is not in the endpoint queue, a negative error code will be returned. Here is the Oops log: Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = dedf0000 [00000000] *pgd=3ede5831, *pte=00000000, *ppte=00000000 Internal error: Oops: 80000007 [#1] ARM Modules linked in: g_hid(-) usb_f_hid libcomposite CPU: 0 PID: 923 Comm: rmmod Not tainted 3.18.0+ #2 Hardware name: Atmel SAMA5 (Device Tree) task: df6b1100 ti: dedf6000 task.ti: dedf6000 PC is at 0x0 LR is at usb_gadget_giveback_request+0xc/0x10 pc : [<00000000>] lr : [<c02ace88>] psr: 60000093 sp : dedf7eb0 ip : df572634 fp : 00000000 r10: 00000000 r9 : df52e210 r8 : 60000013 r7 : df6a9858 r6 : df52e210 r5 : df6a9858 r4 : df572600 r3 : 00000000 r2 : ffffff98 r1 : df572600 r0 : df6a9868 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 3edf0059 DAC: 00000015 Process rmmod (pid: 923, stack limit = 0xdedf6230) Stack: (0xdedf7eb0 to 0xdedf8000) 7ea0: 00000000 c02adbbc df572580 deced608 7ec0: df572600 df6a9868 df572634 c02aed3c df577c00 c01b8608 00000000 df6be27c 7ee0: 00200200 00100100 bf0162f4 c000e544 dedf6000 00000000 00000000 bf010c00 7f00: bf0162cc bf00159c 00000000 df572980 df52e218 00000001 df5729b8 bf0031d0 [..] [<c02ace88>] (usb_gadget_giveback_request) from [<c02adbbc>] (request_complete+0x64/0x88) [<c02adbbc>] (request_complete) from [<c02aed3c>] (usba_ep_dequeue+0x70/0x128) [<c02aed3c>] (usba_ep_dequeue) from [<bf010c00>] (hidg_unbind+0x50/0x7c [usb_f_hid]) [<bf010c00>] (hidg_unbind [usb_f_hid]) from [<bf00159c>] (remove_config.isra.6+0x98/0x9c [libcomposite]) [<bf00159c>] (remove_config.isra.6 [libcomposite]) from [<bf0031d0>] (__composite_unbind+0x34/0x98 [libcomposite]) [<bf0031d0>] (__composite_unbind [libcomposite]) from [<c02acee0>] (usb_gadget_remove_driver+0x50/0x78) [<c02acee0>] (usb_gadget_remove_driver) from [<c02ad570>] (usb_gadget_unregister_driver+0x64/0x94) [<c02ad570>] (usb_gadget_unregister_driver) from [<bf0160c0>] (hidg_cleanup+0x10/0x34 [g_hid]) [<bf0160c0>] (hidg_cleanup [g_hid]) from [<c0056748>] (SyS_delete_module+0x118/0x19c) [<c0056748>] (SyS_delete_module) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30) Code: bad PC value Signed-off-by:
Songjun Wu <songjun.wu@atmel.com> [nicolas.ferre@atmel.com: reworked the commit message] Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 914a3f3b ("USB: add atmel_usba_udc driver") Signed-off-by:
-
Nicholas Bellinger authored
commit 046ba642 upstream. This patch drops the arbitrary maximum I/O size limit in sbc_parse_cdb(), which currently for fabric_max_sectors is hardcoded to 8192 (4 MB for 512 byte sector devices), and for hw_max_sectors is a backend driver dependent value. This limit is problematic because Linux initiators have only recently started to honor block limits MAXIMUM TRANSFER LENGTH, and other non-Linux based initiators (eg: MSFT Fibre Channel) can also generate I/Os larger than 4 MB in size. Currently when this happens, the following message will appear on the target resulting in I/Os being returned with non recoverable status: SCSI OP 28h with too big sectors 16384 exceeds fabric_max_sectors: 8192 Instead, drop both [fabric,hw]_max_sector checks in sbc_parse_cdb(), and convert the existing hw_max_sectors into a purely informational attribute used to represent the granuality that backend driver and/or subsystem code is splitting I/Os upon. Also, update FILEIO with an explicit FD_MAX_BYTES check in fd_execute_rw() to deal with the one special iovec limitiation case. v2 changes: - Drop hw_max_sectors check in sbc_parse_cdb() Reported-by:
Lance Gropper <lance.gropper@qosserver.com> Reported-by:
Stefan Priebe <s.priebe@profihost.ag> Cc: Christoph Hellwig <hch@lst.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Alexander Usyskin authored
commit b13a65ef upstream. H_RST bit in H_CSR register may be found lit before reset is started, for example if preceding reset flow hasn't completed. In that case asserting H_RST will be ignored, therefore we need to clean H_RST bit to start a successful reset sequence. Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ luis: backported to 3.16: - replace dev->dev by &dev->pdev->dev ] Signed-off-by:
-
Arseny Solokha authored
commit 56abcab8 upstream. Commit 8dccddbc ("OHCI: final fix for NVIDIA problems (I hope)") introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development board. The code path that was previously specific to NVIDIA controllers had then become taken for all chips. However, the M5237 installed on the board wedges solid when accessing its base+OHCI_FMINTERVAL register, making it impossible to boot any kernel newer than 3.1.8 on this particular and apparently other similar machines. Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237. The patch is suitable for the -next tree as well as all maintained kernels up to 3.2 inclusive. Signed-off-by:
Arseny Solokha <asolokha@kb.kras.ru> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Hans de Goede authored
commit 3ca8c717 upstream. Just like all previous UAS capable Seagate disk enclosures, these need the US_FL_NO_ATA_1X to not crash when udev probes them. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
commit c6fa3945 upstream. Like the JMicron JMS567 enclosures with the JMS566 choke on report-opcodes, so avoid it. Tested-and-reported-by:
Takeo Nakayama <javhera@gmx.com> Signed-off-by:
-
Hans de Goede authored
commit e5797a3d upstream. This is yet another Seagate device which needs the US_FL_NO_ATA_1X quirk Reported-by:
Marcin Zajączkowski <mszpak@wp.pl> Signed-off-by:
-
Hans de Goede authored
commit 7f5c4d63 upstream. Streams do not work reliabe on Fresco Logic FL1000G xhci controllers, trying to use them results in errors like this: 21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring 21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3570 9067b000 00000000 05000000 01078001 21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring 21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3580 9067b400 00000000 05000000 01038001 As always I've ordered a pci-e addon card with a Fresco Logic controller for myself to see if I can come up with a better fix then the big hammer, in the mean time this will make uas devices work again (in usb-storage mode) for FL1000G users. Reported-by:
-
Alan Stern authored
commit 6d89252a upstream. Commit c3ee9b76 (EHCI: improved logic for isochronous scheduling) introduced the idea of using ehci->last_iso_frame as the origin (or base) for the circular calculations involved in modifying the isochronous schedule. However, the new code it added used ehci->last_iso_frame before the value was properly initialized. This patch rectifies the mistake by moving the initialization lines earlier in iso_stream_schedule(). This fixes Bugzilla #72891. Signed-off-by:
Joe Bryant <tenminjoe@yahoo.com> Tested-by:
Martin Long <martin@longhome.co.uk> Signed-off-by:
-
Mathias Nyman authored
commit f161ead7 upstream. Solves xhci error cases with debug messages: xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1. usb 1-6: hub failed to enable device, error -22 xhci will give a context state error if we try to set a slot in default state to the same default state with a special address device command. Turns out this happends in several cases: - retry reading the device rescriptor in hub_port_init() - usb_reset_device() is called for a slot in default state - in resume path, usb_port_resume() calls hub_port_init() The default state is usually reached from most states with a reset device command without any context state errors, but using the address device command with BSA bit set (block set address) only works from the enabled state and will otherwise cause context error. solve this by checking if we are already in the default state before issuing a address device BSA=1 command. Fixes: 48fc7dbd ("usb: xhci: change enumeration scheme to 'new scheme'") Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Jisheng Zhang authored
commit 5138d5c5 upstream. The gpio4 and gpio5 are in 0xf7fc0000 apb which is located in the SM domain. This patch moves gpio4 and gpio5 to the correct location. This patch also renames them as the following to match the names we internally used in marvell: gpio4 -> sm_gpio1 gpio5 -> sm_gpio0 porte -> portf portf -> porte This also matches what we did for BG2 and BG2CD's SM GPIO. Fixes: cedf57fc ("ARM: dts: berlin: add the BG2Q GPIO nodes") Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Jisheng Zhang authored
commit 5adba7c2 upstream. There's no card detection for the eMMC, so this patch adds the missing broken-cd property. This patch also sets bus width as 8 to add MMC_CAP_8_BIT_DATA in the Host capabilities. Fixes: 3047086d ("ARM: dts: berlin: enable SD card reader and eMMC for the BG2Q DMP") Signed-off-by:
-
Jisheng Zhang authored
commit 96ed6046 upstream. On BG2Q, the sdhci2 host uses nfcecc for "io" clk and nfc for "core" clk. The shdci2 can't work without this patch due to the "core" clk is gated. Fixes: 0d859a6a ("ARM: dts: berlin: add the SDHCI nodes for the BG2Q") Signed-off-by:
-
Reinhard Speyerer authored
commit d80c0d14 upstream. As has been discussed in the thread starting with https://lkml.kernel.org/g/549748e9.d+SiJzqu50f1r4lSAL043YSc@arcor.de Sierra Wireless MC73xx devices with USB VID/PID 0x1199:0x68c0 require the option_send_setup() code to be used on the USB interface for the AT port to make unsolicited response codes work correctly. Move these devices from the qcserial driver where they have been added by commit 70a3615f ("usb: qcserial: add Sierra Wireless MC73xx") to the option driver and add a MC73xx-specific blacklist to ensure that 1. the sendsetup code is not used for the DIAG/DM and NMEA interfaces 2. the option driver does not attach to the QMI/network interfaces Signed-off-by:
Reinhard Speyerer <rspmn@arcor.de> Signed-off-by:
-
Nicholas Bellinger authored
commit 46243860 upstream. While looking at hch's recent conversion to drop the MSG_*_TAG definitions, I noticed a long standing bug in vhost-scsi where the VIRTIO_SCSI_S_* attribute definitions where incorrectly being passed directly into target_submit_cmd_map_sgls(). This patch adds the missing virtio-scsi to TCM/SAM task attribute conversion. Cc: Christoph Hellwig <hch@lst.de> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
David Peterson authored
commit 1ae78a48 upstream. Added virtual com port VID/PID entries for CEL USB sticks and MeshWorks devices. Signed-off-by:
David Peterson <david.peterson@cel.com> Signed-off-by:
-
Fabio Estevam authored
commit 7a9f0604 upstream. GPIO2_5 is the reset GPIO for the USB3317 ULPI PHY. Instead of modelling it as a regulator, the correct approach is to use the 'reset_gpios' property of the "usb-nop-xceiv" node. GPIO1_7 is the reset GPIO for the USB2517 USB hub. As we currently don't have dt bindings to describe a HUB reset, let's keep using the regulator approach. Rename the regulator to 'reg_hub_reset' to better describe its function and bind it with the USB host1 port instead. USB host support has been introduced by commit 9bf206a9 ("ARM: dts: imx51-babbage: Add USB Host1 support"), which landed in 3.16 and it seems that USB has only been functional due to previous bootloader initialization. With this patch applied we can get USB host to work without relying on the bootloader. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Trond Myklebust authored
commit 1fc0703a upstream. Currently, our trunking code will check for session trunking, but will fail to detect client id trunking. This is a problem, because it means that the client will fail to recognise that the two connections represent shared state, even if they do not permit a shared session. By removing the check for the server minor id, and only checking the major id, we will end up doing the right thing in both cases: we close down the new nfs_client and fall back to using the existing one. Fixes: 05f4c350 ("NFS: Discover NFSv4 server trunking when mounting") Cc: Chuck Lever <chuck.lever@oracle.com> Tested-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Trond Myklebust authored
commit 06bed7d1 upstream. This commit fixes a race whereby nlmclnt_init() first starts the lockd daemon, and then calls nlm_bind_host() with the expectation that nlmsvc_timeout has already been initialised. Unfortunately, there is no no synchronisation between lockd() and lockd_up() to guarantee that this is the case. Fix is to move the initialisation of nlmsvc_timeout into lockd_create_svc Fixes: 9a1b6bf8 ("LOCKD: Don't call utsname()->nodename...") Cc: Bruce Fields <bfields@fieldses.org> Signed-off-by:
-
