Merge tag 'usb-ci-v4.21-rc1' of...

Merge tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next

Peter writes:

- Improve the over-current handling for imx
- Add the HSIC support for imx

* tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
  usb: chipidea: imx: allow to configure oc polarity on i.MX25
  usb: chipidea: imx: Warn if oc polarity isn't specified
  usb: chipidea: imx: support configuring for active low oc signal
  doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups
  usb: chipidea: host: override ehci->hub_control
  usb: chipidea: imx: add HSIC support
  usb: chipidea: add flag for imx hsic implementation

Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt

@@ -80,15 +80,19 @@ Optional properties:
   controller. It's expected that a mux state of 0 indicates device mode and a
   mux state of 1 indicates host mode.
 - mux-control-names: Shall be "usb_switch" if mux-controls is specified.
-- pinctrl-names: Names for optional pin modes in "default", "host", "device"
+- pinctrl-names: Names for optional pin modes in "default", "host", "device".
+  In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this
+  case, the "idle" state needs to pull down the data and strobe pin
+  and the "active" state needs to pull up the strobe pin.
 - pinctrl-n: alternate pin modes
 
 i.mx specific properties
 - fsl,usbmisc: phandler of non-core register device, with one
   argument that indicate usb controller index
 - disable-over-current: disable over current detect
-- over-current-active-high: over current signal polarity is high active,
-  typically over current signal polarity is low active.
+- over-current-active-low: over current signal polarity is active low.
+- over-current-active-high: over current signal polarity is active high.
+  It's recommended to specify the over current polarity.
 - external-vbus-divider: enables off-chip resistor divider for Vbus
 
 Example:
@@ -111,3 +115,29 @@ Example:
 		mux-controls = <&usb_switch>;
 		mux-control-names = "usb_switch";
 	};
+
+Example for HSIC:
+
+	usb@2184400 {
+		compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+		reg = <0x02184400 0x200>;
+		interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX6QDL_CLK_USBOH3>;
+		fsl,usbphy = <&usbphynop1>;
+		fsl,usbmisc = <&usbmisc 2>;
+		phy_type = "hsic";
+		dr_mode = "host";
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>;
+		rx-burst-size-dword = <0x10>;
+		pinctrl-names = "idle", "active";
+		pinctrl-0 = <&pinctrl_usbh2_idle>;
+		pinctrl-1 = <&pinctrl_usbh2_active>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbnet: smsc@1 {
+			compatible = "usb424,9730";
+			reg = <1>;
+		};
+	};

drivers/usb/chipidea/ci_hdrc_imx.c

@@ -14,6 +14,7 @@
 #include <linux/usb/chipidea.h>
 #include <linux/usb/of.h>
 #include <linux/clk.h>
+#include <linux/pinctrl/consumer.h>
 
 #include "ci.h"
 #include "ci_hdrc_imx.h"
@@ -85,6 +86,9 @@ struct ci_hdrc_imx_data {
 	bool supports_runtime_pm;
 	bool override_phy_control;
 	bool in_lpm;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *pinctrl_hsic_active;
+	struct regulator *hsic_pad_regulator;
 	/* SoC before i.mx6 (except imx23/imx28) needs three clks */
 	bool need_three_clks;
 	struct clk *clk_ipg;
@@ -132,11 +136,21 @@ static struct imx_usbmisc_data *usbmisc_get_init_data(struct device *dev)
 
 	data->dev = &misc_pdev->dev;
 
-	if (of_find_property(np, "disable-over-current", NULL))
+	/*
+	 * Check the various over current related properties. If over current
+	 * detection is disabled we're not interested in the polarity.
+	 */
+	if (of_find_property(np, "disable-over-current", NULL)) {
 		data->disable_oc = 1;
-
-	if (of_find_property(np, "over-current-active-high", NULL))
-		data->oc_polarity = 1;
+	} else if (of_find_property(np, "over-current-active-high", NULL)) {
+		data->oc_pol_active_low = 0;
+		data->oc_pol_configured = 1;
+	} else if (of_find_property(np, "over-current-active-low", NULL)) {
+		data->oc_pol_active_low = 1;
+		data->oc_pol_configured = 1;
+	} else {
+		dev_warn(dev, "No over current polarity defined\n");
+	}
 
 	if (of_find_property(np, "external-vbus-divider", NULL))
 		data->evdo = 1;
@@ -245,19 +259,49 @@ static void imx_disable_unprepare_clks(struct device *dev)
 	}
 }
 
+static int ci_hdrc_imx_notify_event(struct ci_hdrc *ci, unsigned int event)
+{
+	struct device *dev = ci->dev->parent;
+	struct ci_hdrc_imx_data *data = dev_get_drvdata(dev);
+	int ret = 0;
+
+	switch (event) {
+	case CI_HDRC_IMX_HSIC_ACTIVE_EVENT:
+		ret = pinctrl_select_state(data->pinctrl,
+				data->pinctrl_hsic_active);
+		if (ret)
+			dev_err(dev, "hsic_active select failed, err=%d\n",
+				ret);
+		break;
+	case CI_HDRC_IMX_HSIC_SUSPEND_EVENT:
+		ret = imx_usbmisc_hsic_set_connect(data->usbmisc_data);
+		if (ret)
+			dev_err(dev,
+				"hsic_set_connect failed, err=%d\n", ret);
+		break;
+	default:
+		break;
+	}
+
+	return ret;
+}
+
 static int ci_hdrc_imx_probe(struct platform_device *pdev)
 {
 	struct ci_hdrc_imx_data *data;
 	struct ci_hdrc_platform_data pdata = {
 		.name		= dev_name(&pdev->dev),
 		.capoffset	= DEF_CAPOFFSET,
+		.notify_event	= ci_hdrc_imx_notify_event,
 	};
 	int ret;
 	const struct of_device_id *of_id;
 	const struct ci_hdrc_imx_platform_flag *imx_platform_flag;
 	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct pinctrl_state *pinctrl_hsic_idle;
 
-	of_id = of_match_device(ci_hdrc_imx_dt_ids, &pdev->dev);
+	of_id = of_match_device(ci_hdrc_imx_dt_ids, dev);
 	if (!of_id)
 		return -ENODEV;
 
@@ -268,19 +312,73 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	platform_set_drvdata(pdev, data);
-	data->usbmisc_data = usbmisc_get_init_data(&pdev->dev);
+	data->usbmisc_data = usbmisc_get_init_data(dev);
 	if (IS_ERR(data->usbmisc_data))
 		return PTR_ERR(data->usbmisc_data);
 
-	ret = imx_get_clks(&pdev->dev);
+	if (of_usb_get_phy_mode(dev->of_node) == USBPHY_INTERFACE_MODE_HSIC) {
+		pdata.flags |= CI_HDRC_IMX_IS_HSIC;
+		data->usbmisc_data->hsic = 1;
+		data->pinctrl = devm_pinctrl_get(dev);
+		if (IS_ERR(data->pinctrl)) {
+			dev_err(dev, "pinctrl get failed, err=%ld\n",
+					PTR_ERR(data->pinctrl));
+			return PTR_ERR(data->pinctrl);
+		}
+
+		pinctrl_hsic_idle = pinctrl_lookup_state(data->pinctrl, "idle");
+		if (IS_ERR(pinctrl_hsic_idle)) {
+			dev_err(dev,
+				"pinctrl_hsic_idle lookup failed, err=%ld\n",
+					PTR_ERR(pinctrl_hsic_idle));
+			return PTR_ERR(pinctrl_hsic_idle);
+		}
+
+		ret = pinctrl_select_state(data->pinctrl, pinctrl_hsic_idle);
+		if (ret) {
+			dev_err(dev, "hsic_idle select failed, err=%d\n", ret);
+			return ret;
+		}
+
+		data->pinctrl_hsic_active = pinctrl_lookup_state(data->pinctrl,
+								"active");
+		if (IS_ERR(data->pinctrl_hsic_active)) {
+			dev_err(dev,
+				"pinctrl_hsic_active lookup failed, err=%ld\n",
+					PTR_ERR(data->pinctrl_hsic_active));
+			return PTR_ERR(data->pinctrl_hsic_active);
+		}
+
+		data->hsic_pad_regulator = devm_regulator_get(dev, "hsic");
+		if (PTR_ERR(data->hsic_pad_regulator) == -EPROBE_DEFER) {
+			return -EPROBE_DEFER;
+		} else if (PTR_ERR(data->hsic_pad_regulator) == -ENODEV) {
+			/* no pad regualator is needed */
+			data->hsic_pad_regulator = NULL;
+		} else if (IS_ERR(data->hsic_pad_regulator)) {
+			dev_err(dev, "Get HSIC pad regulator error: %ld\n",
+					PTR_ERR(data->hsic_pad_regulator));
+			return PTR_ERR(data->hsic_pad_regulator);
+		}
+
+		if (data->hsic_pad_regulator) {
+			ret = regulator_enable(data->hsic_pad_regulator);
+			if (ret) {
+				dev_err(dev,
+					"Failed to enable HSIC pad regulator\n");
+				return ret;
+			}
+		}
+	}
+	ret = imx_get_clks(dev);
 	if (ret)
-		return ret;
+		goto disable_hsic_regulator;
 
-	ret = imx_prepare_enable_clks(&pdev->dev);
+	ret = imx_prepare_enable_clks(dev);
 	if (ret)
-		return ret;
+		goto disable_hsic_regulator;
 
-	data->phy = devm_usb_get_phy_by_phandle(&pdev->dev, "fsl,usbphy", 0);
+	data->phy = devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0);
 	if (IS_ERR(data->phy)) {
 		ret = PTR_ERR(data->phy);
 		/* Return -EINVAL if no usbphy is available */
@@ -305,40 +403,43 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)
 
 	ret = imx_usbmisc_init(data->usbmisc_data);
 	if (ret) {
-		dev_err(&pdev->dev, "usbmisc init failed, ret=%d\n", ret);
+		dev_err(dev, "usbmisc init failed, ret=%d\n", ret);
 		goto err_clk;
 	}
 
-	data->ci_pdev = ci_hdrc_add_device(&pdev->dev,
+	data->ci_pdev = ci_hdrc_add_device(dev,
 				pdev->resource, pdev->num_resources,
 				&pdata);
 	if (IS_ERR(data->ci_pdev)) {
 		ret = PTR_ERR(data->ci_pdev);
 		if (ret != -EPROBE_DEFER)
-			dev_err(&pdev->dev,
-				"ci_hdrc_add_device failed, err=%d\n", ret);
+			dev_err(dev, "ci_hdrc_add_device failed, err=%d\n",
+					ret);
 		goto err_clk;
 	}
 
 	ret = imx_usbmisc_init_post(data->usbmisc_data);
 	if (ret) {
-		dev_err(&pdev->dev, "usbmisc post failed, ret=%d\n", ret);
+		dev_err(dev, "usbmisc post failed, ret=%d\n", ret);
 		goto disable_device;
 	}
 
 	if (data->supports_runtime_pm) {
-		pm_runtime_set_active(&pdev->dev);
-		pm_runtime_enable(&pdev->dev);
+		pm_runtime_set_active(dev);
+		pm_runtime_enable(dev);
 	}
 
-	device_set_wakeup_capable(&pdev->dev, true);
+	device_set_wakeup_capable(dev, true);
 
 	return 0;
 
 disable_device:
 	ci_hdrc_remove_device(data->ci_pdev);
 err_clk:
-	imx_disable_unprepare_clks(&pdev->dev);
+	imx_disable_unprepare_clks(dev);
+disable_hsic_regulator:
+	if (data->hsic_pad_regulator)
+		ret = regulator_disable(data->hsic_pad_regulator);
 	return ret;
 }
 
@@ -355,6 +456,8 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev)
 	if (data->override_phy_control)
 		usb_phy_shutdown(data->phy);
 	imx_disable_unprepare_clks(&pdev->dev);
+	if (data->hsic_pad_regulator)
+		regulator_disable(data->hsic_pad_regulator);
 
 	return 0;
 }
@@ -367,9 +470,16 @@ static void ci_hdrc_imx_shutdown(struct platform_device *pdev)
 static int __maybe_unused imx_controller_suspend(struct device *dev)
 {
 	struct ci_hdrc_imx_data *data = dev_get_drvdata(dev);
+	int ret = 0;
 
 	dev_dbg(dev, "at %s\n", __func__);
 
+	ret = imx_usbmisc_hsic_set_clk(data->usbmisc_data, false);
+	if (ret) {
+		dev_err(dev, "usbmisc hsic_set_clk failed, ret=%d\n", ret);
+		return ret;
+	}
+
 	imx_disable_unprepare_clks(dev);
 	data->in_lpm = true;
 
@@ -400,8 +510,16 @@ static int __maybe_unused imx_controller_resume(struct device *dev)
 		goto clk_disable;
 	}
 
+	ret = imx_usbmisc_hsic_set_clk(data->usbmisc_data, true);
+	if (ret) {
+		dev_err(dev, "usbmisc hsic_set_clk failed, ret=%d\n", ret);
+		goto hsic_set_clk_fail;
+	}
+
 	return 0;
 
+hsic_set_clk_fail:
+	imx_usbmisc_set_wakeup(data->usbmisc_data, true);
 clk_disable:
 	imx_disable_unprepare_clks(dev);
 	return ret;

drivers/usb/chipidea/ci_hdrc_imx.h

@@ -11,13 +11,22 @@ struct imx_usbmisc_data {
 	int index;
 
 	unsigned int disable_oc:1; /* over current detect disabled */
-	unsigned int oc_polarity:1; /* over current polarity if oc enabled */
+
+	/* true if over-current polarity is active low */
+	unsigned int oc_pol_active_low:1;
+
+	/* true if dt specifies polarity */
+	unsigned int oc_pol_configured:1;
+
 	unsigned int evdo:1; /* set external vbus divider option */
 	unsigned int ulpi:1; /* connected to an ULPI phy */
+	unsigned int hsic:1; /* HSIC controlller */
 };
 
-int imx_usbmisc_init(struct imx_usbmisc_data *);
-int imx_usbmisc_init_post(struct imx_usbmisc_data *);
-int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *, bool);
+int imx_usbmisc_init(struct imx_usbmisc_data *data);
+int imx_usbmisc_init_post(struct imx_usbmisc_data *data);
+int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *data, bool enabled);
+int imx_usbmisc_hsic_set_connect(struct imx_usbmisc_data *data);
+int imx_usbmisc_hsic_set_clk(struct imx_usbmisc_data *data, bool on);
 
 #endif /* __DRIVER_USB_CHIPIDEA_CI_HDRC_IMX_H */

drivers/usb/chipidea/host.c

@@ -170,6 +170,11 @@ static int host_start(struct ci_hdrc *ci)
 			otg->host = &hcd->self;
 			hcd->self.otg_port = 1;
 		}
+
+		if (ci->platdata->notify_event &&
+			(ci->platdata->flags & CI_HDRC_IMX_IS_HSIC))
+			ci->platdata->notify_event
+				(ci, CI_HDRC_IMX_HSIC_ACTIVE_EVENT);
 	}
 
 	return ret;
@@ -215,9 +220,85 @@ void ci_hdrc_host_destroy(struct ci_hdrc *ci)
 		host_stop(ci);
 }
 
+/* The below code is based on tegra ehci driver */
+static int ci_ehci_hub_control(
+	struct usb_hcd	*hcd,
+	u16		typeReq,
+	u16		wValue,
+	u16		wIndex,
+	char		*buf,
+	u16		wLength
+)
+{
+	struct ehci_hcd	*ehci = hcd_to_ehci(hcd);
+	u32 __iomem	*status_reg;
+	u32		temp;
+	unsigned long	flags;
+	int		retval = 0;
+	struct device *dev = hcd->self.controller;
+	struct ci_hdrc *ci = dev_get_drvdata(dev);
+
+	status_reg = &ehci->regs->port_status[(wIndex & 0xff) - 1];
+
+	spin_lock_irqsave(&ehci->lock, flags);
+
+	if (typeReq == SetPortFeature && wValue == USB_PORT_FEAT_SUSPEND) {
+		temp = ehci_readl(ehci, status_reg);
+		if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) {
+			retval = -EPIPE;
+			goto done;
+		}
+
+		temp &= ~(PORT_RWC_BITS | PORT_WKCONN_E);
+		temp |= PORT_WKDISC_E | PORT_WKOC_E;
+		ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
+
+		/*
+		 * If a transaction is in progress, there may be a delay in
+		 * suspending the port. Poll until the port is suspended.
+		 */
+		if (ehci_handshake(ehci, status_reg, PORT_SUSPEND,
+			PORT_SUSPEND, 5000))
+			ehci_err(ehci, "timeout waiting for SUSPEND\n");
+
+		if (ci->platdata->flags & CI_HDRC_IMX_IS_HSIC) {
+			if (ci->platdata->notify_event)
+				ci->platdata->notify_event(ci,
+					CI_HDRC_IMX_HSIC_SUSPEND_EVENT);
+
+			temp = ehci_readl(ehci, status_reg);
+			temp &= ~(PORT_WKDISC_E | PORT_WKCONN_E);
+			ehci_writel(ehci, temp, status_reg);
+		}
+
+		set_bit((wIndex & 0xff) - 1, &ehci->suspended_ports);
+		goto done;
+	}
+
+	/*
+	 * After resume has finished, it needs do some post resume
+	 * operation for some SoCs.
+	 */
+	else if (typeReq == ClearPortFeature &&
+		wValue == USB_PORT_FEAT_C_SUSPEND) {
+		/* Make sure the resume has finished, it should be finished */
+		if (ehci_handshake(ehci, status_reg, PORT_RESUME, 0, 25000))
+			ehci_err(ehci, "timeout waiting for resume\n");
+	}
+
+	spin_unlock_irqrestore(&ehci->lock, flags);
+
+	/* Handle the hub control events here */
+	return ehci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
+done:
+	spin_unlock_irqrestore(&ehci->lock, flags);
+	return retval;
+}
 static int ci_ehci_bus_suspend(struct usb_hcd *hcd)
 {
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	struct device *dev = hcd->self.controller;
+	struct ci_hdrc *ci = dev_get_drvdata(dev);
 	int port;
 	u32 tmp;
 
@@ -249,6 +330,16 @@ static int ci_ehci_bus_suspend(struct usb_hcd *hcd)
 			 * It needs a short delay between set RS bit and PHCD.
 			 */
 			usleep_range(150, 200);
+			/*
+			 * Need to clear WKCN and WKOC for imx HSIC,
+			 * otherwise, there will be wakeup event.
+			 */
+			if (ci->platdata->flags & CI_HDRC_IMX_IS_HSIC) {
+				tmp = ehci_readl(ehci, reg);
+				tmp &= ~(PORT_WKDISC_E | PORT_WKCONN_E);
+				ehci_writel(ehci, tmp, reg);
+			}
+
 			break;
 		}
 	}
@@ -281,4 +372,5 @@ void ci_hdrc_host_driver_init(void)
 	ehci_init_driver(&ci_ehci_hc_driver, &ehci_ci_overrides);
 	orig_bus_suspend = ci_ehci_hc_driver.bus_suspend;
 	ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend;
+	ci_ehci_hc_driver.hub_control = ci_ehci_hub_control;
 }

drivers/usb/chipidea/usbmisc_imx.c

@@ -64,10 +64,22 @@
 #define MX6_BM_OVER_CUR_DIS		BIT(7)
 #define MX6_BM_OVER_CUR_POLARITY	BIT(8)
 #define MX6_BM_WAKEUP_ENABLE		BIT(10)
+#define MX6_BM_UTMI_ON_CLOCK		BIT(13)
 #define MX6_BM_ID_WAKEUP		BIT(16)
 #define MX6_BM_VBUS_WAKEUP		BIT(17)
 #define MX6SX_BM_DPDM_WAKEUP_EN		BIT(29)
 #define MX6_BM_WAKEUP_INTR		BIT(31)
+
+#define MX6_USB_HSIC_CTRL_OFFSET	0x10
+/* Send resume signal without 480Mhz PHY clock */
+#define MX6SX_BM_HSIC_AUTO_RESUME	BIT(23)
+/* set before portsc.suspendM = 1 */
+#define MX6_BM_HSIC_DEV_CONN		BIT(21)
+/* HSIC enable */
+#define MX6_BM_HSIC_EN			BIT(12)
+/* Force HSIC module 480M clock on, even when in Host is in suspend mode */
+#define MX6_BM_HSIC_CLK_ON		BIT(11)
+
 #define MX6_USB_OTG1_PHY_CTRL		0x18
 /* For imx6dql, it is host-only controller, for later imx6, it is otg's */
 #define MX6_USB_OTG2_PHY_CTRL		0x1c
@@ -94,6 +106,10 @@ struct usbmisc_ops {
 	int (*post)(struct imx_usbmisc_data *data);
 	/* It's called when we need to enable/disable usb wakeup */
 	int (*set_wakeup)(struct imx_usbmisc_data *data, bool enabled);
+	/* It's called before setting portsc.suspendM */
+	int (*hsic_set_connect)(struct imx_usbmisc_data *data);
+	/* It's called during suspend/resume */
+	int (*hsic_set_clk)(struct imx_usbmisc_data *data, bool enabled);
 };
 
 struct imx_usbmisc {
@@ -120,6 +136,14 @@ static int usbmisc_imx25_init(struct imx_usbmisc_data *data)
 		val &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PP_BIT);
 		val |= (MX25_EHCI_INTERFACE_DIFF_UNI & MX25_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT;
 		val |= (MX25_OTG_PM_BIT | MX25_OTG_OCPOL_BIT);
+
+		/*
+		 * If the polarity is not configured assume active high for
+		 * historical reasons.
+		 */
+		if (data->oc_pol_configured && data->oc_pol_active_low)
+			val &= ~MX25_OTG_OCPOL_BIT;
+
 		writel(val, usbmisc->base);
 		break;
 	case 1:
@@ -129,6 +153,13 @@ static int usbmisc_imx25_init(struct imx_usbmisc_data *data)
 		val |= (MX25_H1_PM_BIT | MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT |
 			MX25_H1_USBTE_BIT | MX25_H1_IPPUE_DOWN_BIT);
 
+		/*
+		 * If the polarity is not configured assume active high for
+		 * historical reasons.
+		 */
+		if (data->oc_pol_configured && data->oc_pol_active_low)
+			val &= ~MX25_H1_OCPOL_BIT;
+
 		writel(val, usbmisc->base);
 
 		break;
@@ -340,11 +371,17 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data)
 	reg = readl(usbmisc->base + data->index * 4);
 	if (data->disable_oc) {
 		reg |= MX6_BM_OVER_CUR_DIS;
-	} else if (data->oc_polarity == 1) {
-		/* High active */
-		reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY);
 	} else {
-		reg &= ~(MX6_BM_OVER_CUR_DIS);
+		reg &= ~MX6_BM_OVER_CUR_DIS;
+
+		/*
+		 * If the polarity is not configured keep it as setup by the
+		 * bootloader.
+		 */
+		if (data->oc_pol_configured && data->oc_pol_active_low)
+			reg |= MX6_BM_OVER_CUR_POLARITY;
+		else if (data->oc_pol_configured)
+			reg &= ~MX6_BM_OVER_CUR_POLARITY;
 	}
 	writel(reg, usbmisc->base + data->index * 4);
 
@@ -353,6 +390,18 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data)
 	writel(reg | MX6_BM_NON_BURST_SETTING,
 			usbmisc->base + data->index * 4);
 
+	/* For HSIC controller */
+	if (data->hsic) {
+		reg = readl(usbmisc->base + data->index * 4);
+		writel(reg | MX6_BM_UTMI_ON_CLOCK,
+			usbmisc->base + data->index * 4);
+		reg = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET
+			+ (data->index - 2) * 4);
+		reg |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
+		writel(reg, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET
+			+ (data->index - 2) * 4);
+	}
+
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
 	usbmisc_imx6q_set_wakeup(data, false);
@@ -360,6 +409,79 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data)
 	return 0;
 }
 
+static int usbmisc_imx6_hsic_get_reg_offset(struct imx_usbmisc_data *data)
+{
+	int offset, ret = 0;
+
+	if (data->index == 2 || data->index == 3) {
+		offset = (data->index - 2) * 4;
+	} else if (data->index == 0) {
+		/*
+		 * For SoCs like i.MX7D and later, each USB controller has
+		 * its own non-core register region. For SoCs before i.MX7D,
+		 * the first two USB controllers are non-HSIC controllers.
+		 */
+		offset = 0;
+	} else {
+		dev_err(data->dev, "index is error for usbmisc\n");
+		ret = -EINVAL;
+	}
+
+	return ret ? ret : offset;
+}
+
+static int usbmisc_imx6_hsic_set_connect(struct imx_usbmisc_data *data)
+{
+	unsigned long flags;
+	u32 val;
+	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
+	int offset;
+
+	spin_lock_irqsave(&usbmisc->lock, flags);
+	offset = usbmisc_imx6_hsic_get_reg_offset(data);
+	if (offset < 0) {
+		spin_unlock_irqrestore(&usbmisc->lock, flags);
+		return offset;
+	}
+
+	val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+	if (!(val & MX6_BM_HSIC_DEV_CONN))
+		writel(val | MX6_BM_HSIC_DEV_CONN,
+			usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+
+	spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+	return 0;
+}
+
+static int usbmisc_imx6_hsic_set_clk(struct imx_usbmisc_data *data, bool on)
+{
+	unsigned long flags;
+	u32 val;
+	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
+	int offset;
+
+	spin_lock_irqsave(&usbmisc->lock, flags);
+	offset = usbmisc_imx6_hsic_get_reg_offset(data);
+	if (offset < 0) {
+		spin_unlock_irqrestore(&usbmisc->lock, flags);
+		return offset;
+	}
+
+	val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+	val |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
+	if (on)
+		val |= MX6_BM_HSIC_CLK_ON;
+	else
+		val &= ~MX6_BM_HSIC_CLK_ON;
+
+	writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
+	spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+	return 0;
+}
+
+
 static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data)
 {
 	void __iomem *reg = NULL;
@@ -385,6 +507,13 @@ static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data)
 		spin_unlock_irqrestore(&usbmisc->lock, flags);
 	}
 
+	/* For HSIC controller */
+	if (data->hsic) {
+		val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
+		val |= MX6SX_BM_HSIC_AUTO_RESUME;
+		writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
+	}
+
 	return 0;
 }
 
@@ -444,9 +573,17 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
 	reg = readl(usbmisc->base);
 	if (data->disable_oc) {
 		reg |= MX6_BM_OVER_CUR_DIS;
-	} else if (data->oc_polarity == 1) {
-		/* High active */
-		reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY);
+	} else {
+		reg &= ~MX6_BM_OVER_CUR_DIS;
+
+		/*
+		 * If the polarity is not configured keep it as setup by the
+		 * bootloader.
+		 */
+		if (data->oc_pol_configured && data->oc_pol_active_low)
+			reg |= MX6_BM_OVER_CUR_POLARITY;
+		else if (data->oc_pol_configured)
+			reg &= ~MX6_BM_OVER_CUR_POLARITY;
 	}
 	writel(reg, usbmisc->base);
 
@@ -454,6 +591,7 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
 	reg &= ~MX7D_USB_VBUS_WAKEUP_SOURCE_MASK;
 	writel(reg | MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID,
 		 usbmisc->base + MX7D_USBNC_USB_CTRL2);
+
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
 	usbmisc_imx7d_set_wakeup(data, false);
@@ -481,6 +619,8 @@ static const struct usbmisc_ops imx53_usbmisc_ops = {
 static const struct usbmisc_ops imx6q_usbmisc_ops = {
 	.set_wakeup = usbmisc_imx6q_set_wakeup,
 	.init = usbmisc_imx6q_init,
+	.hsic_set_connect = usbmisc_imx6_hsic_set_connect,
+	.hsic_set_clk   = usbmisc_imx6_hsic_set_clk,
 };
 
 static const struct usbmisc_ops vf610_usbmisc_ops = {
@@ -490,6 +630,8 @@ static const struct usbmisc_ops vf610_usbmisc_ops = {
 static const struct usbmisc_ops imx6sx_usbmisc_ops = {
 	.set_wakeup = usbmisc_imx6q_set_wakeup,
 	.init = usbmisc_imx6sx_init,
+	.hsic_set_connect = usbmisc_imx6_hsic_set_connect,
+	.hsic_set_clk = usbmisc_imx6_hsic_set_clk,
 };
 
 static const struct usbmisc_ops imx7d_usbmisc_ops = {
@@ -546,6 +688,33 @@ int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *data, bool enabled)
 }
 EXPORT_SYMBOL_GPL(imx_usbmisc_set_wakeup);
 
+int imx_usbmisc_hsic_set_connect(struct imx_usbmisc_data *data)
+{
+	struct imx_usbmisc *usbmisc;
+
+	if (!data)
+		return 0;
+
+	usbmisc = dev_get_drvdata(data->dev);
+	if (!usbmisc->ops->hsic_set_connect || !data->hsic)
+		return 0;
+	return usbmisc->ops->hsic_set_connect(data);
+}
+EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_connect);
+
+int imx_usbmisc_hsic_set_clk(struct imx_usbmisc_data *data, bool on)
+{
+	struct imx_usbmisc *usbmisc;
+
+	if (!data)
+		return 0;
+
+	usbmisc = dev_get_drvdata(data->dev);
+	if (!usbmisc->ops->hsic_set_clk || !data->hsic)
+		return 0;
+	return usbmisc->ops->hsic_set_clk(data, on);
+}
+EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_clk);
 static const struct of_device_id usbmisc_imx_dt_ids[] = {
 	{
 		.compatible = "fsl,imx25-usbmisc",

include/linux/usb/chipidea.h

@@ -60,9 +60,12 @@ struct ci_hdrc_platform_data {
 #define CI_HDRC_OVERRIDE_RX_BURST	BIT(11)
 #define CI_HDRC_OVERRIDE_PHY_CONTROL	BIT(12) /* Glue layer manages phy */
 #define CI_HDRC_REQUIRES_ALIGNED_DMA	BIT(13)
+#define CI_HDRC_IMX_IS_HSIC		BIT(14)
 	enum usb_dr_mode	dr_mode;
 #define CI_HDRC_CONTROLLER_RESET_EVENT		0
 #define CI_HDRC_CONTROLLER_STOPPED_EVENT	1
+#define CI_HDRC_IMX_HSIC_ACTIVE_EVENT		2
+#define CI_HDRC_IMX_HSIC_SUSPEND_EVENT		3
 	int	(*notify_event) (struct ci_hdrc *ci, unsigned event);
 	struct regulator	*reg_vbus;
 	struct usb_otg_caps	ci_otg_caps;