ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)

The STiH4{07,10} platform contains some interconnect clocks which are used
by various IPs.  If this clock isn't handled correctly by ST's EHCI/OHCI
drivers, their hub won't be found, the following error be shown and the
result will be non-working USB:

  [   97.221963] hub 2-1:1.0: hub_ext_port_status failed (err = -110)

Cc: stable@vger.kernel.org
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>

arch/arm/boot/dts/stih410.dtsi

@@ -41,7 +41,8 @@ ohci0: usb@9a03c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
 			interrupts = <GIC_SPI 180 IRQ_TYPE_NONE>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
 			reset-names = "power", "softreset";
@@ -57,7 +58,8 @@ ehci0: usb@9a03e00 {
 			interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
 			reset-names = "power", "softreset";
@@ -71,7 +73,8 @@ ohci1: usb@9a83c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a83c00 0x100>;
 			interrupts = <GIC_SPI 181 IRQ_TYPE_NONE>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
 			reset-names = "power", "softreset";
@@ -87,7 +90,8 @@ ehci1: usb@9a83e00 {
 			interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
-			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
 			reset-names = "power", "softreset";