ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect

Each eTSEC MAC has its own TBI (SGMII) PCS and private MDIO bus.
But due to a DTS oversight, both SGMII-compatible MACs of the LS1021 SoC
are pointing towards the same internal PCS. Therefore nobody is
controlling the internal PCS of eTSEC0.

Upon initial ndo_open, the SGMII link is ok by virtue of U-boot
initialization. But upon an ifdown/ifup sequence, the code path from
ndo_open -> init_phy -> gfar_configure_serdes does not get executed for
the PCS of eTSEC0 (and is executed twice for MAC eTSEC1). So the SGMII
link remains down for eTSEC0. On the LS1021A-TWR board, to signal this
failure condition, the PHY driver keeps printing
'803x_aneg_done: SGMII link is not ok'.

Also, it changes compatible of mdio0 to "fsl,etsec2-mdio" to match
mdio1 device.

Fixes: 055223d4 ("ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arch/arm/boot/dts/ls1021a-twr.dts

@@ -145,7 +145,7 @@ dspiflash: s25fl064k@0 {
 };
 
 &enet0 {
-	tbi-handle = <&tbi1>;
+	tbi-handle = <&tbi0>;
 	phy-handle = <&sgmii_phy2>;
 	phy-connection-type = "sgmii";
 	status = "okay";
@@ -225,6 +225,13 @@ rgmii_phy1: ethernet-phy@1 {
 	sgmii_phy2: ethernet-phy@2 {
 		reg = <0x2>;
 	};
+	tbi0: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&mdio1 {
 	tbi1: tbi-phy@1f {
 		reg = <0x1f>;
 		device_type = "tbi-phy";

arch/arm/boot/dts/ls1021a.dtsi

@@ -701,7 +701,7 @@ dcu: dcu@2ce0000 {
 		};
 
 		mdio0: mdio@2d24000 {
-			compatible = "gianfar";
+			compatible = "fsl,etsec2-mdio";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -709,6 +709,15 @@ mdio0: mdio@2d24000 {
 			      <0x0 0x2d10030 0x0 0x4>;
 		};
 
+		mdio1: mdio@2d64000 {
+			compatible = "fsl,etsec2-mdio";
+			device_type = "mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2d64000 0x0 0x4000>,
+			      <0x0 0x2d50030 0x0 0x4>;
+		};
+
 		ptp_clock@2d10e00 {
 			compatible = "fsl,etsec-ptp";
 			reg = <0x0 0x2d10e00 0x0 0xb0>;