Merge tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt

From Shawn Guo:

imx device tree changes for 3.11:

* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
  imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver

* tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (82 commits)
  ARM: dts: imx27: Add VPU devicetree node
  ARM: mxc: fix gpio-ranges for VF610
  ARM: dtsi: imx6qdl-sabresd: Enable WM8962 audio support
  ARM: dtsi: imx6qdl-sabresd: Enable SSI2 and AUDMUX
  ARM: dtsi: imx6qdl-sabresd: Add WM8962 CODEC support
  ARM: dtsi: imx6qdl-sabresd: add a fixed regulator for WM8962
  ARM: dtsi: imx6dl: Add a pinctrl for AUDMUX
  ARM: dtsi: imx6q/imx6dl: Add a pinctrl for I2C1
  ARM: dts: imx6qdl-sabresd: add clko1 iomux configuration
  ARM: dts: Phytec imx6q pfla02 and pbab01 support
  ARM: dts: imx6q: Add pinctrl for usdhc2 and enet
  ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flash
  ARM: dts: imx27-phytec-phycore-rdk: Add SDHC support
  ARM: dts: i.MX27: Add SDHC devicetree nodes
  ARM: dts: i.MX27: Add DMA devicetree node
  ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR
  ARM: dts: imx6dl: add pinctrls for WEIM NOR
  ARM: dts: imx6q: add pinctrls for WEIM NOR
  ARM: dts: imx6qdl: add more information for WEIM
  ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/bus/imx-weim.txt

+Device tree bindings for i.MX Wireless External Interface Module (WEIM)
+
+The term "wireless" does not imply that the WEIM is literally an interface
+without wires. It simply means that this module was originally designed for
+wireless and mobile applications that use low-power technology.
+
+The actual devices are instantiated from the child nodes of a WEIM node.
+
+Required properties:
+
+ - compatible:		Should be set to "fsl,imx6q-weim"
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - clocks:		the clock, see the example below.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+Timing property for child nodes. It is mandatory, not optional.
+
+ - fsl,weim-cs-timing:	The timing array, contains 6 timing values for the
+			child node. We can get the CS index from the child
+			node's "reg" property. This property contains the values
+			for the registers EIM_CSnGCR1, EIM_CSnGCR2, EIM_CSnRCR1,
+			EIM_CSnRCR2, EIM_CSnWCR1, EIM_CSnWCR2 in this order.
+
+Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
+
+	weim: weim@021b8000 {
+		compatible = "fsl,imx6q-weim";
+		reg = <0x021b8000 0x4000>;
+		clocks = <&clks 196>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x08000000>;
+
+		nor@0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x02000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+					0x0000c000 0x1404a38e 0x00000000>;
+		};
+	};

Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt

@@ -58,7 +58,7 @@ Some requirements for using fsl,imx-pinctrl binding:
 
 Examples:
 usdhc@0219c000 { /* uSDHC4 */
-	fsl,card-wired;
+	non-removable;
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 	pinctrl-names = "default";

arch/arm/boot/dts/Makefile

@@ -107,13 +107,15 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx27-apf27.dtb \
 	imx27-apf27dev.dtb \
 	imx27-pdk.dtb \
-	imx27-phytec-phycore.dtb \
+	imx27-phytec-phycore-som.dtb \
+	imx27-phytec-phycore-rdk.dtb \
 	imx31-bug.dtb \
 	imx51-apf51.dtb \
 	imx51-apf51dev.dtb \
 	imx51-babbage.dtb \
 	imx53-ard.dtb \
 	imx53-evk.dtb \
+	imx53-m53evk.dtb \
 	imx53-mba53.dtb \
 	imx53-qsb.dtb \
 	imx53-smd.dtb \
@@ -121,10 +123,13 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard.dtb \
 	imx6q-arm2.dtb \
+	imx6q-phytec-pbab01.dtb \
 	imx6q-sabreauto.dtb \
 	imx6q-sabrelite.dtb \
 	imx6q-sabresd.dtb \
-	imx6q-sbc6x.dtb
+	imx6q-sbc6x.dtb \
+	imx6sl-evk.dtb \
+	vf610-twr.dtb
 dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx23-olinuxino.dtb \
 	imx23-stmp378x_devb.dtb \

arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts

+/*
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx27-phytec-phycore-som.dts"
+
+/ {
+	model = "Phytec pcm970";
+	compatible = "phytec,imx27-pcm970", "phytec,imx27-pcm038", "fsl,imx27";
+};
+
+&cspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio4 28 0>, <&gpio4 27 0>;
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	cd-gpios = <&gpio3 29 0>;
+	wp-gpios = <&gpio3 28 0>;
+	vmmc-supply = <&vmmc1_reg>;
+	status = "okay";
+};
+
+&uart1 {
+	fsl,uart-has-rtscts;
+};
+
+&uart2 {
+	fsl,uart-has-rtscts;
+	status = "okay";
+};

arch/arm/boot/dts/imx27-phytec-phycore.dts → arch/arm/boot/dts/imx27-phytec-phycore-som.dts

@@ -23,17 +23,6 @@ memory {
 	soc {
 		aipi@10000000 { /* aipi1 */
 			serial@1000a000 {
-				fsl,uart-has-rtscts;
-				status = "okay";
-			};
-
-			serial@1000b000 {
-				fsl,uart-has-rtscts;
-				status = "okay";
-			};
-
-			serial@1000c000 {
-				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
@@ -58,6 +47,7 @@ lm75@4a {
 
 		aipi@10020000 { /* aipi2 */
 			ethernet@1002b000 {
+				phy-reset-gpios = <&gpio3 30 0>;
 				status = "okay";
 			};
 		};
@@ -67,11 +57,121 @@ nor_flash@c0000000 {
 		compatible = "cfi-flash";
 		bank-width = <2>;
 		reg = <0xc0000000 0x02000000>;
+		linux,mtd-name = "physmap-flash.0";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 };
 
+&cspi1 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio4 28 0>;
+	status = "okay";
+
+	pmic: mc13783@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mc13783";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <23 0x4>;
+		fsl,mc13xxx-uses-adc;
+		fsl,mc13xxx-uses-rtc;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			sw1b_reg: sw1b {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			sw2a_reg: sw2a {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			sw2b_reg: sw2b {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vaudio_reg: vaudio {
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			violo_reg: violo {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			viohi_reg: viohi {
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen_reg: vgen {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcam_reg: vcam {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vrf1_reg: vrf1 {
+				regulator-min-microvolt = <2775000>;
+				regulator-max-microvolt = <2775000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vrf2_reg: vrf2 {
+				regulator-min-microvolt = <2775000>;
+				regulator-max-microvolt = <2775000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vmmc1_reg: vmmc1 {
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			gpo1_reg: gpo1 { };
+
+			pwgt1spi_reg: pwgt1spi {
+				regulator-always-on;
+			};
+		};
+	};
+};
+
 &nfc {
 	nand-bus-width = <8>;
 	nand-ecc-mode = "hw";

arch/arm/boot/dts/imx27.dtsi

@@ -25,6 +25,9 @@ aliases {
 		gpio3 = &gpio4;
 		gpio4 = &gpio5;
 		gpio5 = &gpio6;
+		spi0 = &cspi1;
+		spi1 = &cspi2;
+		spi2 = &cspi3;
 	};
 
 	avic: avic-interrupt-controller@e0000000 {
@@ -58,6 +61,16 @@ aipi@10000000 { /* AIPI1 */
 			reg = <0x10000000 0x20000>;
 			ranges;
 
+			dma: dma@10001000 {
+				compatible = "fsl,imx27-dma";
+				reg = <0x10001000 0x1000>;
+				interrupts = <32>;
+				clocks = <&clks 50>, <&clks 70>;
+				clock-names = "ipg", "ahb";
+				#dma-cells = <1>;
+				#dma-channels = <16>;
+			};
+
 			wdog: wdog@10002000 {
 				compatible = "fsl,imx27-wdt", "fsl,imx21-wdt";
 				reg = <0x10002000 0x1000>;
@@ -89,6 +102,14 @@ gpt3: timer@10005000 {
 				clock-names = "ipg", "per";
 			};
 
+			pwm0: pwm@10006000 {
+				compatible = "fsl,imx27-pwm";
+				reg = <0x10006000 0x1000>;
+				interrupts = <23>;
+				clocks = <&clks 34>, <&clks 61>;
+				clock-names = "ipg", "per";
+			};
+
 			uart1: serial@1000a000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1000a000 0x1000>;
@@ -157,6 +178,28 @@ i2c1: i2c@10012000 {
 				status = "disabled";
 			};
 
+			sdhci1: sdhci@10013000 {
+				compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
+				reg = <0x10013000 0x1000>;
+				interrupts = <11>;
+				clocks = <&clks 30>, <&clks 60>;
+				clock-names = "ipg", "per";
+				dmas = <&dma 7>;
+				dma-names = "rx-tx";
+				status = "disabled";
+			};
+
+			sdhci2: sdhci@10014000 {
+				compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
+				reg = <0x10014000 0x1000>;
+				interrupts = <10>;
+				clocks = <&clks 29>, <&clks 60>;
+				clock-names = "ipg", "per";
+				dmas = <&dma 6>;
+				dma-names = "rx-tx";
+				status = "disabled";
+			};
+
 			gpio1: gpio@10015000 {
 				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
 				reg = <0x10015000 0x100>;
@@ -272,6 +315,17 @@ i2c2: i2c@1001d000 {
 				status = "disabled";
 			};
 
+			sdhci3: sdhci@1001e000 {
+				compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
+				reg = <0x1001e000 0x1000>;
+				interrupts = <9>;
+				clocks = <&clks 28>, <&clks 60>;
+				clock-names = "ipg", "per";
+				dmas = <&dma 36>;
+				dma-names = "rx-tx";
+				status = "disabled";
+			};
+
 			gpt6: timer@1001f000 {
 				compatible = "fsl,imx27-gpt", "fsl,imx1-gpt";
 				reg = <0x1001f000 0x1000>;
@@ -288,6 +342,21 @@ aipi@10020000 { /* AIPI2 */
 			reg = <0x10020000 0x20000>;
 			ranges;
 
+			coda: coda@10023000 {
+				compatible = "fsl,imx27-vpu";
+				reg = <0x10023000 0x0200>;
+				interrupts = <53>;
+				clocks = <&clks 57>, <&clks 66>;
+				clock-names = "per", "ahb";
+				iram = <&iram>;
+			};
+
+			clks: ccm@10027000{
+				compatible = "fsl,imx27-ccm";
+				reg = <0x10027000 0x1000>;
+				#clock-cells = <1>;
+			};
+
 			fec: ethernet@1002b000 {
 				compatible = "fsl,imx27-fec";
 				reg = <0x1002b000 0x4000>;
@@ -296,19 +365,16 @@ fec: ethernet@1002b000 {
 				clock-names = "ipg", "ahb", "ptp";
 				status = "disabled";
 			};
-
-			clks: ccm@10027000{
-				compatible = "fsl,imx27-ccm";
-				reg = <0x10027000 0x1000>;
-				#clock-cells = <1>;
-			};
 		};
 
+		iram: iram@ffff4c00 {
+			compatible = "mmio-sram";
+			reg = <0xffff4c00 0xb400>;
+		};
 
 		nfc: nand@d8000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-
 			compatible = "fsl,imx27-nand";
 			reg = <0xd8000000 0x1000>;
 			interrupts = <29>;

arch/arm/boot/dts/imx51-apf51.dts

@@ -45,6 +45,13 @@ &fec {
 	status = "okay";
 };
 
+&nfc {
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3_2>;

arch/arm/boot/dts/imx51.dtsi

@@ -175,10 +175,20 @@ esdhc4: esdhc@70024000 {
 				};
 			};
 
+			usbphy0: usbphy@0 {
+				compatible = "usb-nop-xceiv";
+				clocks = <&clks 124>;
+				clock-names = "main_clk";
+				status = "okay";
+			};
+
 			usbotg: usb@73f80000 {
 				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
 				reg = <0x73f80000 0x0200>;
 				interrupts = <18>;
+				clocks = <&clks 108>;
+				fsl,usbmisc = <&usbmisc 0>;
+				fsl,usbphy = <&usbphy0>;
 				status = "disabled";
 			};
 
@@ -186,6 +196,8 @@ usbh1: usb@73f80200 {
 				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
 				reg = <0x73f80200 0x0200>;
 				interrupts = <14>;
+				clocks = <&clks 108>;
+				fsl,usbmisc = <&usbmisc 1>;
 				status = "disabled";
 			};
 
@@ -193,6 +205,8 @@ usbh2: usb@73f80400 {
 				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
 				reg = <0x73f80400 0x0200>;
 				interrupts = <16>;
+				clocks = <&clks 108>;
+				fsl,usbmisc = <&usbmisc 2>;
 				status = "disabled";
 			};
 
@@ -200,9 +214,18 @@ usbh3: usb@73f80600 {
 				compatible = "fsl,imx51-usb", "fsl,imx27-usb";
 				reg = <0x73f80600 0x0200>;
 				interrupts = <17>;
+				clocks = <&clks 108>;
+				fsl,usbmisc = <&usbmisc 3>;
 				status = "disabled";
 			};
 
+			usbmisc: usbmisc@73f80800 {
+				#index-cells = <1>;
+				compatible = "fsl,imx51-usbmisc";
+				reg = <0x73f80800 0x200>;
+				clocks = <&clks 108>;
+			};
+
 			gpio1: gpio@73f84000 {
 				compatible = "fsl,imx51-gpio", "fsl,imx35-gpio";
 				reg = <0x73f84000 0x4000>;

arch/arm/boot/dts/imx53-m53evk.dts

+/*
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx53.dtsi"
+
+/ {
+	model = "DENX M53EVK";
+	compatible = "denx,imx53-m53evk", "fsl,imx53";
+
+	memory {
+		reg = <0x70000000 0x20000000>;
+	};
+
+	soc {
+		display@di1 {
+			compatible = "fsl,imx-parallel-display";
+			crtcs = <&ipu 1>;
+			interface-pix-fmt = "bgr666";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_ipu_disp2_1>;
+
+			display-timings {
+				800x480p60 {
+					native-mode;
+					clock-frequency = <31500000>;
+					hactive = <800>;
+					vactive = <480>;
+					hfront-porch = <40>;
+					hback-porch = <88>;
+					hsync-len = <128>;
+					vback-porch = <33>;
+					vfront-porch = <9>;
+					vsync-len = <3>;
+					vsync-active = <1>;
+				};
+			};
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 3000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio>;
+
+		user1 {
+			label = "user1";
+			gpios = <&gpio2 8 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		user2 {
+			label = "user2";
+			gpios = <&gpio2 9 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p2v: 3p2v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P2V";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-always-on;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx53-m53evk-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx53-m53evk-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Ext Spk", "LINE_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <4>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_2>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_3>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2_1>;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1_1>;
+	cd-gpios = <&gpio1 1 0>;
+	wp-gpios = <&gpio1 9 0>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec_1>;
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_2>;
+	status = "okay";
+
+	sgtl5000: codec@0a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		VDDA-supply = <&reg_3p2v>;
+		VDDIO-supply = <&reg_3p2v>;
+		clocks = <&clks 150>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2_2>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	stmpe610@41 {
+		compatible = "st,stmpe610";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x41>;
+		id = <0>;
+		blocks = <0x5>;
+		interrupts = <6 0x0>;
+		interrupt-parent = <&gpio7>;
+		irq-trigger = <0x1>;
+
+		stmpe_touchscreen {
+			compatible = "stmpe,ts";
+			reg = <0>;
+			ts,sample-time = <4>;
+			ts,mod-12b = <1>;
+			ts,ref-sel = <0>;
+			ts,adc-freq = <1>;
+			ts,ave-ctrl = <3>;
+			ts,touch-det-delay = <3>;
+			ts,settling = <4>;
+			ts,fraction-z = <7>;
+			ts,i-drive = <1>;
+		};
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "stm,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	hog {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x80000000
+				MX53_PAD_EIM_EB3__GPIO2_31		0x80000000
+				MX53_PAD_PATA_DA_0__GPIO7_6		0x80000000
+				MX53_PAD_DISP0_DAT8__PWM1_PWMO		0x5
+
+			>;
+		};
+
+		led_pin_gpio: led_gpio@0 {
+			fsl,pins = <
+				MX53_PAD_PATA_DATA8__GPIO2_8		0x80000000
+				MX53_PAD_PATA_DATA9__GPIO2_9		0x80000000
+			>;
+		};
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand_1>;
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1_1>;
+	status = "okay";
+};
+
+&ssi2 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_2>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_1>;
+	status = "okay";
+};

arch/arm/boot/dts/imx53-mba53.dts

@@ -16,27 +16,81 @@
 / {
 	model = "TQ MBa53 starter kit";
 	compatible = "tq,mba53", "tq,tqma53", "fsl,imx53";
+
+	reg_backlight: fixed@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-supply";
+		gpio = <&gpio2 5 0>;
+		startup-delay-us = <5000>;
+		enable-active-low;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 50000 0 0>;
+		brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>;
+		default-brightness-level = <10>;
+		enable-gpios = <&gpio7 7 0>;
+		power-supply = <&reg_backlight>;
+	};
+
+	disp1: display@disp1 {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_disp1_1>;
+		crtcs = <&ipu 1>;
+		interface-pix-fmt = "rgb24";
+		status = "disabled";
+	};
+
+	reg_3p2v: 3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "tq,imx53-mba53-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx53-mba53-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <5>;
+	};
+};
+
+&ldb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lvds1_1>;
+	status = "disabled";
 };
 
 &iomuxc {
 	lvds1 {
 		pinctrl_lvds1_1: lvds1-grp1 {
 			fsl,pins = <
-				MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x10000
-				MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x10000
-				MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x10000
-				MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x10000
-				MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x10000
+				MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000
+				MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000
+				MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000
+				MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000
+				MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000
 			>;
 		};
 
 		pinctrl_lvds1_2: lvds1-grp2 {
 			fsl,pins = <
-				MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x10000
-				MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x10000
-				MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x10000
-				MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x10000
-				MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x10000
+				MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000
+				MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000
+				MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000
+				MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000
+				MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000
 			>;
 		};
 	};
@@ -44,33 +98,44 @@ MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x10000
 	disp1 {
 		pinctrl_disp1_1: disp1-grp1 {
 			fsl,pins = <
-				MX53_PAD_EIM_DA10__IPU_DI1_PIN15   0x10000 /* DISP1_DRDY */
-				MX53_PAD_EIM_D23__IPU_DI1_PIN2     0x10000 /* DISP1_HSYNC */
-				MX53_PAD_EIM_EB3__IPU_DI1_PIN3     0x10000 /* DISP1_VSYNC */
-				MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x10000
-				MX53_PAD_EIM_D27__IPU_DISP1_DAT_23 0x10000
-				MX53_PAD_EIM_D30__IPU_DISP1_DAT_21 0x10000
-				MX53_PAD_EIM_D31__IPU_DISP1_DAT_20 0x10000
-				MX53_PAD_EIM_A24__IPU_DISP1_DAT_19 0x10000
-				MX53_PAD_EIM_A23__IPU_DISP1_DAT_18 0x10000
-				MX53_PAD_EIM_A22__IPU_DISP1_DAT_17 0x10000
-				MX53_PAD_EIM_A21__IPU_DISP1_DAT_16 0x10000
-				MX53_PAD_EIM_A20__IPU_DISP1_DAT_15 0x10000
-				MX53_PAD_EIM_A19__IPU_DISP1_DAT_14 0x10000
-				MX53_PAD_EIM_A18__IPU_DISP1_DAT_13 0x10000
-				MX53_PAD_EIM_A17__IPU_DISP1_DAT_12 0x10000
-				MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11 0x10000
-				MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10 0x10000
-				MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9  0x10000
-				MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8  0x10000
-				MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7  0x10000
-				MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6  0x10000
-				MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5  0x10000
-				MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4  0x10000
-				MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3  0x10000
-				MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2  0x10000
-				MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1  0x10000
-				MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0  0x10000
+				MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK 0x80000000 /* DISP1_CLK */
+				MX53_PAD_EIM_DA10__IPU_DI1_PIN15   0x80000000 /* DISP1_DRDY */
+				MX53_PAD_EIM_D23__IPU_DI1_PIN2     0x80000000 /* DISP1_HSYNC */
+				MX53_PAD_EIM_EB3__IPU_DI1_PIN3     0x80000000 /* DISP1_VSYNC */
+				MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x80000000
+				MX53_PAD_EIM_D27__IPU_DISP1_DAT_23 0x80000000
+				MX53_PAD_EIM_D30__IPU_DISP1_DAT_21 0x80000000
+				MX53_PAD_EIM_D31__IPU_DISP1_DAT_20 0x80000000
+				MX53_PAD_EIM_A24__IPU_DISP1_DAT_19 0x80000000
+				MX53_PAD_EIM_A23__IPU_DISP1_DAT_18 0x80000000
+				MX53_PAD_EIM_A22__IPU_DISP1_DAT_17 0x80000000
+				MX53_PAD_EIM_A21__IPU_DISP1_DAT_16 0x80000000
+				MX53_PAD_EIM_A20__IPU_DISP1_DAT_15 0x80000000
+				MX53_PAD_EIM_A19__IPU_DISP1_DAT_14 0x80000000
+				MX53_PAD_EIM_A18__IPU_DISP1_DAT_13 0x80000000
+				MX53_PAD_EIM_A17__IPU_DISP1_DAT_12 0x80000000
+				MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11 0x80000000
+				MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10 0x80000000
+				MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9  0x80000000
+				MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8  0x80000000
+				MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7  0x80000000
+				MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6  0x80000000
+				MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5  0x80000000
+				MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4  0x80000000
+				MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3  0x80000000
+				MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2  0x80000000
+				MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1  0x80000000
+				MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0  0x80000000
+			>;
+		};
+	};
+
+	tve {
+		pinctrl_vga_sync_1: vgasync-grp1 {
+			fsl,pins = <
+				/* VGA_VSYNC, HSYNC with max drive strength */
+				MX53_PAD_EIM_CS1__IPU_DI1_PIN6	   0xe6
+				MX53_PAD_EIM_DA15__IPU_DI1_PIN4	   0xe6
 			>;
 		};
 	};
@@ -80,16 +145,27 @@ &cspi {
 	status = "okay";
 };
 
+&audmux {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_1>;
+};
+
 &i2c2 {
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		clocks = <&clks 150>;
+		VDDA-supply = <&reg_3p2v>;
+		VDDIO-supply = <&reg_3p2v>;
 	};
 
 	expander: pca9554@20 {
 		compatible = "pca9554";
 		reg = <0x20>;
 		interrupts = <109>;
+		#gpio-cells = <2>;
+		gpio-controller;
 	};
 
 	sensor2: lm75@49 {
@@ -99,6 +175,7 @@ sensor2: lm75@49 {
 };
 
 &fec {
+	phy-reset-gpios = <&gpio7 6 0>;
 	status = "okay";
 };
 
@@ -114,10 +191,24 @@ &ecspi1 {
 	status = "okay";
 };
 
+&usbotg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 };
 
+&ssi2 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
 &uart2 {
 	status = "okay";
 };
@@ -133,3 +224,13 @@ &can2 {
 &i2c3 {
 	status = "okay";
 };
+
+&tve {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_vga_sync_1>;
+	ddc = <&i2c3>;
+	fsl,tve-mode = "vga";
+	fsl,hsync-pin = <4>;
+	fsl,vsync-pin = <6>;
+	status = "okay";
+};

arch/arm/boot/dts/imx53-qsb.dts

@@ -21,6 +21,33 @@ memory {
 		reg = <0x70000000 0x40000000>;
 	};
 
+	display@di0 {
+		compatible = "fsl,imx-parallel-display";
+		crtcs = <&ipu 0>;
+		interface-pix-fmt = "rgb565";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp0_1>;
+		status = "disabled";
+		display-timings {
+			claawvga {
+				native-mode;
+				clock-frequency = <27000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <40>;
+				hfront-porch = <60>;
+				vback-porch = <10>;
+				vfront-porch = <10>;
+				hsync-len = <20>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -147,6 +174,7 @@ sgtl5000: codec@0a {
 		reg = <0x0a>;
 		VDDA-supply = <&reg_3p2v>;
 		VDDIO-supply = <&reg_3p2v>;
+		clocks = <&clks 150>;
 	};
 };
 
@@ -268,3 +296,11 @@ &fec {
 	phy-reset-gpios = <&gpio7 6 0>;
 	status = "okay";
 };
+
+&usbh1 {
+       status = "okay";
+};
+
+&usbotg {
+       status = "okay";
+};

arch/arm/boot/dts/imx53-tqma53.dtsi

@@ -35,7 +35,9 @@ reg_3p3v: 3p3v {
 
 &esdhc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2_1>;
+	pinctrl-0 = <&pinctrl_esdhc2_1>,
+		    <&pinctrl_tqma53_esdhc2_2>;
+	vmmc-supply = <&reg_3p3v>;
 	wp-gpios = <&gpio1 2 0>;
 	cd-gpios = <&gpio1 4 0>;
 	status = "disabled";
@@ -69,14 +71,22 @@ &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	esdhc2_2 {
+		pinctrl_tqma53_esdhc2_2: esdhc2-tqma53-grp2 {
+			fsl,pins = <
+				MX53_PAD_GPIO_4__GPIO1_4	0x80000000 /* SD2_CD */
+				MX53_PAD_GPIO_2__GPIO1_2	0x80000000 /* SD2_WP */
+			>;
+		};
+	};
+
 	i2s {
 		pinctrl_i2s_1: i2s-grp1 {
 			fsl,pins = <
-				 MX53_PAD_GPIO_19__GPIO4_5           0x10000 /* I2S_MCLK */
-				 MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC  0x10000 /* I2S_SCLK */
-				 MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD  0x10000 /* I2S_DOUT */
-				 MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x10000 /* I2S_LRCLK */
-				 MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD  0x10000 /* I2S_DIN */
+				 MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC  0x80000000 /* I2S_SCLK */
+				 MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD  0x80000000 /* I2S_DOUT */
+				 MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 /* I2S_LRCLK */
+				 MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD  0x80000000 /* I2S_DIN */
 			>;
 		};
 	};
@@ -84,16 +94,17 @@ MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD  0x10000 /* I2S_DIN */
 	hog {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				 MX53_PAD_EIM_CS1__IPU_DI1_PIN6  0x10000 /* VSYNC */
-				 MX53_PAD_EIM_DA15__IPU_DI1_PIN4 0x10000 /* HSYNC */
-				 MX53_PAD_PATA_DA_1__GPIO7_7     0x10000 /* LCD_BLT_EN */
-				 MX53_PAD_PATA_DA_2__GPIO7_8     0x10000 /* LCD_RESET */
-				 MX53_PAD_PATA_DATA5__GPIO2_5    0x10000 /* LCD_POWER */
-				 MX53_PAD_PATA_DATA6__GPIO2_6    0x10000 /* PMIC_INT */
-				 MX53_PAD_PATA_DATA14__GPIO2_14  0x10000 /* CSI_RST */
-				 MX53_PAD_PATA_DATA15__GPIO2_15  0x10000 /* CSI_PWDN */
-				 MX53_PAD_GPIO_0__GPIO1_0        0x10000 /* SYSTEM_DOWN */
-				 MX53_PAD_GPIO_3__GPIO1_3        0x10000
+				 MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 /* SSI_MCLK */
+				 MX53_PAD_PATA_DA_1__GPIO7_7     0x80000000 /* LCD_BLT_EN */
+				 MX53_PAD_PATA_DA_2__GPIO7_8     0x80000000 /* LCD_RESET */
+				 MX53_PAD_PATA_DATA5__GPIO2_5    0x80000000 /* LCD_POWER */
+				 MX53_PAD_PATA_DATA6__GPIO2_6    0x80000000 /* PMIC_INT */
+				 MX53_PAD_PATA_DATA14__GPIO2_14  0x80000000 /* CSI_RST */
+				 MX53_PAD_PATA_DATA15__GPIO2_15  0x80000000 /* CSI_PWDN */
+				 MX53_PAD_GPIO_19__GPIO4_5 	 0x80000000 /* #SYSTEM_DOWN */
+				 MX53_PAD_GPIO_3__GPIO1_3        0x80000000
+				 MX53_PAD_PATA_DA_0__GPIO7_6	 0x80000000 /* #PHY_RESET */
+				 MX53_PAD_GPIO_1__PWM2_PWMO	 0x80000000 /* LCD_CONTRAST */
 			>;
 		};
 	};
@@ -149,7 +160,7 @@ pmic: mc34708@8 {
 		reg = <0x8>;
 		fsl,mc13xxx-uses-rtc;
 		interrupt-parent = <&gpio2>;
-		interrupts = <6 8>; /* PDATA_DATA6, low active */
+		interrupts = <6 4>; /* PATA_DATA6, active high */
 	};
 
 	sensor1: lm75@48 {

arch/arm/boot/dts/imx53-tx53.dtsi

+/*
+ * Copyright 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "imx53.dtsi"
+
+/ {
+	model = "Ka-Ro TX53";
+	compatible = "karo,tx53", "fsl,imx53";
+
+	memory {
+		reg = <0x70000000 0x40000000>; /* Up to 1GiB */
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_2>;
+	status = "disabled";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2_1>;
+	status = "disabled";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1_2>;
+	status = "disabled";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1_2>;
+	status = "disabled";
+};
+
+&esdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc2_1>;
+	status = "disabled";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec_1>;
+	phy-mode = "rmii";
+	status = "disabled";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_2>;
+	status = "disabled";
+};
+
+&owire {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_owire_1>;
+	status = "disabled";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2_1>;
+	status = "disabled";
+};
+
+&ssi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_1>;
+	status = "disabled";
+};
+
+&ssi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_2>;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_2>,
+		    <&pinctrl_uart1_3>;
+	fsl,uart-has-rtscts;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_2>;
+	fsl,uart-has-rtscts;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_1>;
+	fsl,uart-has-rtscts;
+	status = "disabled";
+};

arch/arm/boot/dts/imx6dl-sabreauto.dts

@@ -28,4 +28,12 @@ MX6DL_PAD_SD2_DAT2__GPIO1_IO13  0x80000000
 			>;
 		};
 	};
+
+	ecspi1 {
+		pinctrl_ecspi1_sabreauto: ecspi1-sabreauto {
+			fsl,pins = <
+				MX6DL_PAD_EIM_D19__GPIO3_IO19  0x80000000
+			>;
+		};
+	};
 };

arch/arm/boot/dts/imx6dl-sabresd.dts

@@ -29,6 +29,7 @@ MX6DL_PAD_NANDF_D0__GPIO2_IO00 0x80000000
 				MX6DL_PAD_NANDF_D1__GPIO2_IO01 0x80000000
 				MX6DL_PAD_NANDF_D2__GPIO2_IO02 0x80000000
 				MX6DL_PAD_NANDF_D3__GPIO2_IO03 0x80000000
+				MX6DL_PAD_GPIO_0__CCM_CLKO1    0x130b0
 			>;
 		};
 	};

arch/arm/boot/dts/imx6dl.dtsi

@@ -37,6 +37,27 @@ iomuxc: iomuxc@020e0000 {
 				compatible = "fsl,imx6dl-iomuxc";
 				reg = <0x020e0000 0x4000>;
 
+				audmux {
+					pinctrl_audmux_2: audmux-2 {
+						fsl,pins = <
+							MX6DL_PAD_CSI0_DAT7__AUD3_RXD  0x80000000
+							MX6DL_PAD_CSI0_DAT4__AUD3_TXC  0x80000000
+							MX6DL_PAD_CSI0_DAT5__AUD3_TXD  0x80000000
+							MX6DL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000
+						>;
+					};
+				};
+
+				ecspi1 {
+					pinctrl_ecspi1_1: ecspi1grp-1 {
+						fsl,pins = <
+							MX6DL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+							MX6DL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+							MX6DL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+						>;
+					};
+				};
+
 				enet {
 					pinctrl_enet_1: enetgrp-1 {
 						fsl,pins = <
@@ -80,6 +101,39 @@ MX6DL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
 					};
 				};
 
+				gpmi-nand {
+					pinctrl_gpmi_nand_1: gpmi-nand-1 {
+						fsl,pins = <
+							MX6DL_PAD_NANDF_CLE__NAND_CLE     0xb0b1
+							MX6DL_PAD_NANDF_ALE__NAND_ALE     0xb0b1
+							MX6DL_PAD_NANDF_WP_B__NAND_WP_B   0xb0b1
+							MX6DL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+							MX6DL_PAD_NANDF_CS0__NAND_CE0_B   0xb0b1
+							MX6DL_PAD_NANDF_CS1__NAND_CE1_B   0xb0b1
+							MX6DL_PAD_SD4_CMD__NAND_RE_B      0xb0b1
+							MX6DL_PAD_SD4_CLK__NAND_WE_B      0xb0b1
+							MX6DL_PAD_NANDF_D0__NAND_DATA00   0xb0b1
+							MX6DL_PAD_NANDF_D1__NAND_DATA01   0xb0b1
+							MX6DL_PAD_NANDF_D2__NAND_DATA02   0xb0b1
+							MX6DL_PAD_NANDF_D3__NAND_DATA03   0xb0b1
+							MX6DL_PAD_NANDF_D4__NAND_DATA04   0xb0b1
+							MX6DL_PAD_NANDF_D5__NAND_DATA05   0xb0b1
+							MX6DL_PAD_NANDF_D6__NAND_DATA06   0xb0b1
+							MX6DL_PAD_NANDF_D7__NAND_DATA07   0xb0b1
+							MX6DL_PAD_SD4_DAT0__NAND_DQS      0x00b1
+						>;
+					};
+				};
+
+				i2c1 {
+					pinctrl_i2c1_2: i2c1grp-2 {
+						fsl,pins = <
+							MX6DL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+							MX6DL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+						>;
+					};
+				};
+
 				uart1 {
 					pinctrl_uart1_1: uart1grp-1 {
 						fsl,pins = <
@@ -151,6 +205,64 @@ MX6DL_PAD_SD3_DAT3__SD3_DATA3 0x17059
 					};
 				};
 
+				weim {
+					pinctrl_weim_cs0_1: weim_cs0grp-1 {
+						fsl,pins = <
+							MX6DL_PAD_EIM_CS0__EIM_CS0_B   0xb0b1
+						>;
+					};
+
+					pinctrl_weim_nor_1: weim_norgrp-1 {
+						fsl,pins = <
+							MX6DL_PAD_EIM_OE__EIM_OE_B     0xb0b1
+							MX6DL_PAD_EIM_RW__EIM_RW       0xb0b1
+							MX6DL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+							/* data */
+							MX6DL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+							MX6DL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+							MX6DL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+							MX6DL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+							MX6DL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+							MX6DL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+							MX6DL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+							MX6DL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+							MX6DL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+							MX6DL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+							MX6DL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+							MX6DL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+							MX6DL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+							MX6DL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+							MX6DL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+							MX6DL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+							/* address */
+							MX6DL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+							MX6DL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+							MX6DL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+							MX6DL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+							MX6DL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+							MX6DL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+							MX6DL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+							MX6DL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+							MX6DL_PAD_EIM_DA15__EIM_AD15  0xb0b1
+							MX6DL_PAD_EIM_DA14__EIM_AD14  0xb0b1
+							MX6DL_PAD_EIM_DA13__EIM_AD13  0xb0b1
+							MX6DL_PAD_EIM_DA12__EIM_AD12  0xb0b1
+							MX6DL_PAD_EIM_DA11__EIM_AD11  0xb0b1
+							MX6DL_PAD_EIM_DA10__EIM_AD10  0xb0b1
+							MX6DL_PAD_EIM_DA9__EIM_AD09   0xb0b1
+							MX6DL_PAD_EIM_DA8__EIM_AD08   0xb0b1
+							MX6DL_PAD_EIM_DA7__EIM_AD07   0xb0b1
+							MX6DL_PAD_EIM_DA6__EIM_AD06   0xb0b1
+							MX6DL_PAD_EIM_DA5__EIM_AD05   0xb0b1
+							MX6DL_PAD_EIM_DA4__EIM_AD04   0xb0b1
+							MX6DL_PAD_EIM_DA3__EIM_AD03   0xb0b1
+							MX6DL_PAD_EIM_DA2__EIM_AD02   0xb0b1
+							MX6DL_PAD_EIM_DA1__EIM_AD01   0xb0b1
+							MX6DL_PAD_EIM_DA0__EIM_AD00   0xb0b1
+						>;
+					};
+
+				};
 
 			};
 

arch/arm/boot/dts/imx6q-phytec-pbab01.dts

+/*
+ * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q-phytec-pfla02.dtsi"
+
+/ {
+	model = "Phytec phyFLEX-i.MX6 Quad Carrier-Board";
+	compatible = "phytec,imx6q-pbab01", "phytec,imx6q-pfla02", "fsl,imx6q";
+};
+
+&fec {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};

arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi

+/*
+ * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx6q.dtsi"
+
+/ {
+	model = "Phytec phyFLEX-i.MX6 Ouad";
+	compatible = "phytec,imx6q-pfla02", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	hog {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX6Q_PAD_EIM_D23__GPIO3_IO23    0x80000000
+			>;
+		};
+	};
+
+	pfla02 {
+		pinctrl_usdhc3_pfla02: usdhc3grp-pfla02 {
+			fsl,pins = <
+				MX6Q_PAD_ENET_RXD0__GPIO1_IO27  0x80000000
+				MX6Q_PAD_ENET_TXD1__GPIO1_IO29  0x80000000
+			>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_3>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 0>;
+	status = "disabled";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4_1>;
+	status = "disabled";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_2>;
+	cd-gpios = <&gpio1 4 0>;
+	wp-gpios = <&gpio1 2 0>;
+	status = "disabled";
+};
+
+&usdhc3 {
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_usdhc3_2
+		     &pinctrl_usdhc3_pfla02>;
+        cd-gpios = <&gpio1 27 0>;
+        wp-gpios = <&gpio1 29 0>;
+        status = "disabled";
+};

arch/arm/boot/dts/imx6q-sabreauto.dts

@@ -32,4 +32,12 @@ MX6Q_PAD_SD2_DAT2__GPIO1_IO13  0x80000000
 			>;
 		};
 	};
+
+	ecspi1 {
+		pinctrl_ecspi1_sabreauto: ecspi1-sabreauto {
+			fsl,pins = <
+				MX6Q_PAD_EIM_D19__GPIO3_IO19  0x80000000
+			>;
+		};
+	};
 };

arch/arm/boot/dts/imx6q-sabresd.dts

@@ -33,6 +33,7 @@ MX6Q_PAD_NANDF_D0__GPIO2_IO00 0x80000000
 				MX6Q_PAD_NANDF_D1__GPIO2_IO01 0x80000000
 				MX6Q_PAD_NANDF_D2__GPIO2_IO02 0x80000000
 				MX6Q_PAD_NANDF_D3__GPIO2_IO03 0x80000000
+				MX6Q_PAD_GPIO_0__CCM_CLKO1    0x130b0
 			>;
 		};
 	};

arch/arm/boot/dts/imx6q.dtsi

@@ -161,6 +161,27 @@ MX6Q_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
 							MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
 						>;
 					};
+
+					pinctrl_enet_3: enetgrp-3 {
+						fsl,pins = <
+							MX6Q_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
+							MX6Q_PAD_ENET_MDC__ENET_MDC         0x1b0b0
+							MX6Q_PAD_RGMII_TXC__RGMII_TXC       0x1b0b0
+							MX6Q_PAD_RGMII_TD0__RGMII_TD0       0x1b0b0
+							MX6Q_PAD_RGMII_TD1__RGMII_TD1       0x1b0b0
+							MX6Q_PAD_RGMII_TD2__RGMII_TD2       0x1b0b0
+							MX6Q_PAD_RGMII_TD3__RGMII_TD3       0x1b0b0
+							MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+							MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
+							MX6Q_PAD_RGMII_RXC__RGMII_RXC       0x1b0b0
+							MX6Q_PAD_RGMII_RD0__RGMII_RD0       0x1b0b0
+							MX6Q_PAD_RGMII_RD1__RGMII_RD1       0x1b0b0
+							MX6Q_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
+							MX6Q_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
+							MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+							MX6Q_PAD_ENET_TX_EN__ENET_TX_EN     0x1b0b0
+						>;
+					};
 				};
 
 				gpmi-nand {
@@ -172,8 +193,6 @@ MX6Q_PAD_NANDF_WP_B__NAND_WP_B   0xb0b1
 							MX6Q_PAD_NANDF_RB0__NAND_READY_B 0xb000
 							MX6Q_PAD_NANDF_CS0__NAND_CE0_B   0xb0b1
 							MX6Q_PAD_NANDF_CS1__NAND_CE1_B   0xb0b1
-							MX6Q_PAD_NANDF_CS2__NAND_CE2_B   0xb0b1
-							MX6Q_PAD_NANDF_CS3__NAND_CE3_B   0xb0b1
 							MX6Q_PAD_SD4_CMD__NAND_RE_B      0xb0b1
 							MX6Q_PAD_SD4_CLK__NAND_WE_B      0xb0b1
 							MX6Q_PAD_NANDF_D0__NAND_DATA00   0xb0b1
@@ -196,6 +215,13 @@ MX6Q_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
 							MX6Q_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
 						>;
 					};
+
+					pinctrl_i2c1_2: i2c1grp-2 {
+						fsl,pins = <
+							MX6Q_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+							MX6Q_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+						>;
+					};
 				};
 
 				i2c2 {
@@ -272,6 +298,17 @@ MX6Q_PAD_NANDF_D6__SD2_DATA6 0x17059
 							MX6Q_PAD_NANDF_D7__SD2_DATA7 0x17059
 						>;
 					};
+
+					pinctrl_usdhc2_2: usdhc2grp-2 {
+						fsl,pins = <
+							MX6Q_PAD_SD2_CMD__SD2_CMD    0x17059
+							MX6Q_PAD_SD2_CLK__SD2_CLK    0x10059
+							MX6Q_PAD_SD2_DAT0__SD2_DATA0 0x17059
+							MX6Q_PAD_SD2_DAT1__SD2_DATA1 0x17059
+							MX6Q_PAD_SD2_DAT2__SD2_DATA2 0x17059
+							MX6Q_PAD_SD2_DAT3__SD2_DATA3 0x17059
+						>;
+					};
 				};
 
 				usdhc3 {
@@ -329,6 +366,65 @@ MX6Q_PAD_SD4_DAT3__SD4_DATA3 0x17059
 						>;
 					};
 				};
+
+				weim {
+					pinctrl_weim_cs0_1: weim_cs0grp-1 {
+						fsl,pins = <
+							MX6Q_PAD_EIM_CS0__EIM_CS0_B   0xb0b1
+						>;
+					};
+
+					pinctrl_weim_nor_1: weimnorgrp-1 {
+						fsl,pins = <
+							MX6Q_PAD_EIM_OE__EIM_OE_B     0xb0b1
+							MX6Q_PAD_EIM_RW__EIM_RW       0xb0b1
+							MX6Q_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+							/* data */
+							MX6Q_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+							MX6Q_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+							MX6Q_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+							MX6Q_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+							MX6Q_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+							MX6Q_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+							MX6Q_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+							MX6Q_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+							MX6Q_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+							MX6Q_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+							MX6Q_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+							MX6Q_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+							MX6Q_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+							MX6Q_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+							MX6Q_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+							MX6Q_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+							/* address */
+							MX6Q_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+							MX6Q_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+							MX6Q_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+							MX6Q_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+							MX6Q_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+							MX6Q_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+							MX6Q_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+							MX6Q_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+							MX6Q_PAD_EIM_DA15__EIM_AD15  0xb0b1
+							MX6Q_PAD_EIM_DA14__EIM_AD14  0xb0b1
+							MX6Q_PAD_EIM_DA13__EIM_AD13  0xb0b1
+							MX6Q_PAD_EIM_DA12__EIM_AD12  0xb0b1
+							MX6Q_PAD_EIM_DA11__EIM_AD11  0xb0b1
+							MX6Q_PAD_EIM_DA10__EIM_AD10  0xb0b1
+							MX6Q_PAD_EIM_DA9__EIM_AD09   0xb0b1
+							MX6Q_PAD_EIM_DA8__EIM_AD08   0xb0b1
+							MX6Q_PAD_EIM_DA7__EIM_AD07   0xb0b1
+							MX6Q_PAD_EIM_DA6__EIM_AD06   0xb0b1
+							MX6Q_PAD_EIM_DA5__EIM_AD05   0xb0b1
+							MX6Q_PAD_EIM_DA4__EIM_AD04   0xb0b1
+							MX6Q_PAD_EIM_DA3__EIM_AD03   0xb0b1
+							MX6Q_PAD_EIM_DA2__EIM_AD02   0xb0b1
+							MX6Q_PAD_EIM_DA1__EIM_AD01   0xb0b1
+							MX6Q_PAD_EIM_DA0__EIM_AD00   0xb0b1
+						>;
+					};
+
+				};
 			};
 		};
 

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -16,6 +16,22 @@ memory {
 	};
 };
 
+&ecspi1 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio3 19 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_sabreauto>;
+	status = "disabled"; /* pin conflict with WEIM NOR */
+
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet_2>;
@@ -23,6 +39,12 @@ &fec {
 	status = "okay";
 };
 
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand_1>;
+	status = "okay";
+};
+
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4_1>;
@@ -36,3 +58,22 @@ &usdhc3 {
 	wp-gpios = <&gpio1 13 0>;
 	status = "okay";
 };
+
+&weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim_nor_1 &pinctrl_weim_cs0_1>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x08000000 0x08000000>;
+	status = "disabled"; /* pin conflict with SPI NOR */
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		reg = <0 0 0x02000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+				0x0000c000 0x1404a38e 0x00000000>;
+	};
+};

arch/arm/boot/dts/imx6qdl-sabresd.dtsi

@@ -26,6 +26,13 @@ reg_usb_otg_vbus: usb_otg_vbus {
 			gpio = <&gpio3 22 0>;
 			enable-active-high;
 		};
+
+		reg_audio: wm8962_supply {
+			compatible = "regulator-fixed";
+			regulator-name = "wm8962-supply";
+			gpio = <&gpio4 10 0>;
+			enable-active-high;
+		};
 	};
 
 	gpio-keys {
@@ -43,6 +50,31 @@ volume-down {
 			linux,code = <114>; /* KEY_VOLUMEDOWN */
 		};
 	};
+
+	sound {
+		compatible = "fsl,imx6q-sabresd-wm8962",
+			   "fsl,imx-audio-wm8962";
+		model = "wm8962-audio";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Ext Spk", "SPKOUTL",
+			"Ext Spk", "SPKOUTR",
+			"MICBIAS", "AMIC",
+			"IN3R", "MICBIAS",
+			"DMIC", "MICBIAS",
+			"DMICDAT", "DMIC";
+		mux-int-port = <2>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_2>;
+	status = "okay";
 };
 
 &fec {
@@ -52,6 +84,40 @@ &fec {
 	status = "okay";
 };
 
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_2>;
+	status = "okay";
+
+	codec: wm8962@1a {
+		compatible = "wlf,wm8962";
+		reg = <0x1a>;
+		clocks = <&clks 169>;
+		DCVDD-supply = <&reg_audio>;
+		DBVDD-supply = <&reg_audio>;
+		AVDD-supply = <&reg_audio>;
+		CPVDD-supply = <&reg_audio>;
+		MICVDD-supply = <&reg_audio>;
+		PLLVDD-supply = <&reg_audio>;
+		SPKVDD1-supply = <&reg_audio>;
+		SPKVDD2-supply = <&reg_audio>;
+		gpio-cfg = <
+			0x0000 /* 0:Default */
+			0x0000 /* 1:Default */
+			0x0013 /* 2:FN_DMICCLK */
+			0x0000 /* 3:Default */
+			0x8014 /* 4:FN_DMICCDAT */
+			0x0000 /* 5:Default */
+		>;
+       };
+};
+
+&ssi2 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_1>;

arch/arm/boot/dts/imx6qdl.dtsi

@@ -106,6 +106,8 @@ L2: l2-cache@00a02000 {
 			interrupts = <0 92 0x04>;
 			cache-unified;
 			cache-level = <2>;
+			arm,tag-latency = <4 2 3>;
+			arm,data-latency = <4 2 3>;
 		};
 
 		pmu {
@@ -638,7 +640,7 @@ usbh3: usb@02184600 {
 				status = "disabled";
 			};
 
-			usbmisc: usbmisc: usbmisc@02184800 {
+			usbmisc: usbmisc@02184800 {
 				#index-cells = <1>;
 				compatible = "fsl,imx6q-usbmisc";
 				reg = <0x02184800 0x200>;
@@ -742,9 +744,11 @@ mmdc1: mmdc@021b4000 { /* MMDC1 */
 				reg = <0x021b4000 0x4000>;
 			};
 
-			weim@021b8000 {
+			weim: weim@021b8000 {
+				compatible = "fsl,imx6q-weim";
 				reg = <0x021b8000 0x4000>;
 				interrupts = <0 14 0x04>;
+				clocks = <&clks 196>;
 			};
 
 			ocotp@021bc000 {
@@ -752,11 +756,6 @@ ocotp@021bc000 {
 				reg = <0x021bc000 0x4000>;
 			};
 
-			ocotp@021c0000 {
-				reg = <0x021c0000 0x4000>;
-				interrupts = <0 21 0x04>;
-			};
-
 			tzasc@021d0000 { /* TZASC1 */
 				reg = <0x021d0000 0x4000>;
 				interrupts = <0 108 0x04>;

arch/arm/boot/dts/imx6sl-evk.dts

+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Freescale i.MX6 SoloLite EVK Board";
+	compatible = "fsl,imx6sl-evk", "fsl,imx6sl";
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec_1>;
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	hog {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX6SL_PAD_KEY_ROW7__GPIO4_IO07    0x17059
+				MX6SL_PAD_KEY_COL7__GPIO4_IO06    0x17059
+				MX6SL_PAD_SD2_DAT7__GPIO5_IO00    0x17059
+				MX6SL_PAD_SD2_DAT6__GPIO4_IO29    0x17059
+				MX6SL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059
+			>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1_1>;
+	bus-width = <8>;
+	cd-gpios = <&gpio4 7 0>;
+	wp-gpios = <&gpio4 6 0>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_1>;
+	cd-gpios = <&gpio5 0 0>;
+	wp-gpios = <&gpio4 29 0>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_1>;
+	cd-gpios = <&gpio3 22 0>;
+	status = "okay";
+};

arch/arm/boot/dts/vf610-twr.dts

+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+/dts-v1/;
+#include "vf610.dtsi"
+
+/ {
+	model = "VF610 Tower Board";
+	compatible = "fsl,vf610-twr", "fsl,vf610";
+
+	chosen {
+		bootargs = "console=ttyLP1,115200";
+	};
+
+	memory {
+		reg = <0x80000000 0x8000000>;
+	};
+
+	clocks {
+		audio_ext {
+			compatible = "fixed-clock";
+			clock-frequency = <24576000>;
+		};
+
+		enet_ext {
+			compatible = "fixed-clock";
+			clock-frequency = <50000000>;
+		};
+	};
+
+};
+
+&fec0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec0_1>;
+	status = "okay";
+};
+
+&fec1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1_1>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	status = "okay";
+};

arch/arm/mach-imx/clk-imx51-imx53.c

@@ -327,8 +327,6 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "imx-ssi.0");
 	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "imx-ssi.1");
 	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "imx-ssi.2");
-	clk_register_clkdev(clk[ssi_ext1_gate], "ssi_ext1", NULL);
-	clk_register_clkdev(clk[ssi_ext2_gate], "ssi_ext2", NULL);
 	clk_register_clkdev(clk[sdma_gate], NULL, "imx35-sdma");
 	clk_register_clkdev(clk[cpu_podf], NULL, "cpufreq-cpu0.0");
 	clk_register_clkdev(clk[iim_gate], "iim", NULL);

arch/arm/mach-imx/mach-imx53.c

@@ -24,26 +24,10 @@
 #include "hardware.h"
 #include "mx53.h"
 
-static void __init imx53_qsb_init(void)
-{
-	struct clk *clk;
-
-	clk = clk_get_sys(NULL, "ssi_ext1");
-	if (IS_ERR(clk)) {
-		pr_err("failed to get clk ssi_ext1\n");
-		return;
-	}
-
-	clk_register_clkdev(clk, NULL, "0-000a");
-}
-
 static void __init imx53_dt_init(void)
 {
 	mxc_arch_reset_init_dt();
 
-	if (of_machine_is_compatible("fsl,imx53-qsb"))
-		imx53_qsb_init();
-
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 

drivers/bus/Kconfig

@@ -4,6 +4,15 @@
 
 menu "Bus devices"
 
+config IMX_WEIM
+	bool "Freescale EIM DRIVER"
+	depends on ARCH_MXC
+	help
+	  Driver for i.MX6 WEIM controller.
+	  The WEIM(Wireless External Interface Module) works like a bus.
+	  You can attach many different devices on it, such as NOR, onenand.
+	  But now, we only support the Parallel NOR.
+
 config MVEBU_MBUS
 	bool
 	depends on PLAT_ORION

drivers/bus/Makefile

@@ -2,6 +2,7 @@
 # Makefile for the bus drivers.
 #
 
+obj-$(CONFIG_IMX_WEIM)	+= imx-weim.o
 obj-$(CONFIG_MVEBU_MBUS) += mvebu-mbus.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 

drivers/bus/imx-weim.c

+/*
+ * EIM driver for Freescale's i.MX chips
+ *
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+
+struct imx_weim {
+	void __iomem *base;
+	struct clk *clk;
+};
+
+static const struct of_device_id weim_id_table[] = {
+	{ .compatible = "fsl,imx6q-weim", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, weim_id_table);
+
+#define CS_TIMING_LEN 6
+#define CS_REG_RANGE  0x18
+
+/* Parse and set the timing for this device. */
+static int
+weim_timing_setup(struct platform_device *pdev, struct device_node *np)
+{
+	struct imx_weim *weim = platform_get_drvdata(pdev);
+	u32 value[CS_TIMING_LEN];
+	u32 cs_idx;
+	int ret;
+	int i;
+
+	/* get the CS index from this child node's "reg" property. */
+	ret = of_property_read_u32(np, "reg", &cs_idx);
+	if (ret)
+		return ret;
+
+	/* The weim has four chip selects. */
+	if (cs_idx > 3)
+		return -EINVAL;
+
+	ret = of_property_read_u32_array(np, "fsl,weim-cs-timing",
+					value, CS_TIMING_LEN);
+	if (ret)
+		return ret;
+
+	/* set the timing for WEIM */
+	for (i = 0; i < CS_TIMING_LEN; i++)
+		writel(value[i], weim->base + cs_idx * CS_REG_RANGE + i * 4);
+	return 0;
+}
+
+static int weim_parse_dt(struct platform_device *pdev)
+{
+	struct device_node *child;
+	int ret;
+
+	for_each_child_of_node(pdev->dev.of_node, child) {
+		if (!child->name)
+			continue;
+
+		ret = weim_timing_setup(pdev, child);
+		if (ret) {
+			dev_err(&pdev->dev, "%s set timing failed.\n",
+				child->full_name);
+			return ret;
+		}
+	}
+
+	ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+	if (ret)
+		dev_err(&pdev->dev, "%s fail to create devices.\n",
+			pdev->dev.of_node->full_name);
+	return ret;
+}
+
+static int weim_probe(struct platform_device *pdev)
+{
+	struct imx_weim *weim;
+	struct resource *res;
+	int ret = -EINVAL;
+
+	weim = devm_kzalloc(&pdev->dev, sizeof(*weim), GFP_KERNEL);
+	if (!weim) {
+		ret = -ENOMEM;
+		goto weim_err;
+	}
+	platform_set_drvdata(pdev, weim);
+
+	/* get the resource */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	weim->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(weim->base)) {
+		ret = PTR_ERR(weim->base);
+		goto weim_err;
+	}
+
+	/* get the clock */
+	weim->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(weim->clk))
+		goto weim_err;
+
+	ret = clk_prepare_enable(weim->clk);
+	if (ret)
+		goto weim_err;
+
+	/* parse the device node */
+	ret = weim_parse_dt(pdev);
+	if (ret) {
+		clk_disable_unprepare(weim->clk);
+		goto weim_err;
+	}
+
+	dev_info(&pdev->dev, "WEIM driver registered.\n");
+	return 0;
+
+weim_err:
+	return ret;
+}
+
+static struct platform_driver weim_driver = {
+	.driver = {
+		.name = "imx-weim",
+		.of_match_table = weim_id_table,
+	},
+	.probe   = weim_probe,
+};
+
+module_platform_driver(weim_driver);
+MODULE_AUTHOR("Freescale Semiconductor Inc.");
+MODULE_DESCRIPTION("i.MX EIM Controller Driver");
+MODULE_LICENSE("GPL");