From Lee Jones. It's an update of the previous ux500/dt branch with a few more
patches:

* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
  ARM: ux500: Describe UART platform registering issues more accurately
  ARM: ux500: Enable all MMC devices on the u9540 when booting with DT
  ARM: ux500: Enable SDI4 port on the u9540 when booting with Device Tree
  ARM: ux500: Add UART support to the u9540 Device Tree
  ARM: ux500: Add skeleton DTS file for the u9540
  ARM: ux500: Add SDI (MMC) support to the HREF Device Tree
  ARM: ux500: Move regulator-name properties out to board DTS files
Signed-off-by: Olof Johansson <olof@lixom.net>

From Roland Stigge:
DTS updates for the LPC32xx Soc for 3.7

This time, only one patch: Adding the motor PWM to lpc32xx.dtsi

* tag 'lpc32xx-dts-for-3.7' of git://git.antcom.de/linux-2.6:
  ARM: LPC32xx: Add the motor PWM to base dts file
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt

From Stephen Warren:
ARM: tegra: device tree changes

A wide variety of device tree additions are made across many Tegra
boards:

* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
  and Whistler.

This pull request is based on tegra-for-3.8-soc.

* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
  ARM: tegra: whistler: enable HDMI port
  ARM: tegra: tec: Enable HDMI output
  ARM: tegra: plutux: Enable HDMI output
  ARM: tegra: tamonten: Add host1x support
  ARM: tegra: trimslice: enable HDMI port
  ARM: tegra: harmony: enable HDMI port
  ARM: tegra: Add Tegra30 host1x support
  ARM: tegra: Add Tegra20 host1x support
  ARM: tegra: trimslice: enable SPI flash
  ARM: tegra: dts: add sflash controller dt entry
  ARM: tegra: ventana: Add NCT1008 temperature sensor
  ARM: tegra: tamonten: Add NCT1008 temperature sensor
  ARM: tegra: harmony: Add ADT7641 temperature sensor
  ARM: tegra: tec: Remove redundant DT properties
  ARM: tegra: tamonten: Add DDC/PTA pinmux
  ARM: tegra: dts: cardhu: enable SLINK4
  ARM: tegra: dts: add slink controller dt entry
  ARM: dt: tegra: ventana: define pinmux for ddc
  ARM: dt: t30 cardhu: set pinmux and power for wlan
  ARM: dt: t20 ventana: set pinmux and power for wlan
  ...

From Nicolas Ferre:
More DT material for AT91:

- conversion of watchdog to DT
- usart definition for evk-pro3 board

* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
  ARM: at91/dts: evk-pro3: enable watchdog
  ARM: at91/dts: add at91sam9_wdt driver to at91sam926x, at91sam9g45
  watchdog: at91sam9_wdt: add device tree support
  ARM: at91: dt: evk-pro3: enable uart0 and uart2

UARTs no longer require call-back information, since the reset
call-back was removed in 43b5f0d6.
The only AUXDATA dependencies remaining for UARTs are DMA settings.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the 3 UART nodes required to enable serial ports on the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The dtb targets belong in arch/arm/boot/dts/Makefile now, so move the
newly added davinci targets there.
Signed-off-by: Olof Johansson <olof@lixom.net>

From Sekhar Nori:

These changes add DT boot support to DaVinci DA850
SoC.

* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
  ARM: davinci: da850: generate dtbs for da850 boards
  ARM: davinci: add support for am1808 based EnBW CMC board
  ARM: davinci: da850 evm: add DT data
  ARM: davinci: da850: add SoC DT data
  ARM: davinci: da850: add DT boot support
  ARM: davinci: da8xx: add DA850 PRUSS support
  ARM: davinci: add platform hook to fetch the SRAM pool
  ARM: davinci: da850: changed SRAM allocator to shared ram.
  ARM: davinci: sram: switch from iotable to ioremapped regions
  uio: uio_pruss: replace private SRAM API with genalloc
  ARM: davinci: serial: provide API to initialze UART clocks
  ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>

Enable host1x, and the HDMI output. Whistler also has a DSI-based LCD,
and a VGA output. tegradrm doesn't support either of those output types
yet.

Based on work by Thierry Reding for TrimSlice.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch.  Most of them are dts changes.
There are also a few imx6 improvement patches in there.

* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx6q: select ARM and PL310 errata
  ARM: imx6q: print silicon version on boot
  ARM i.MX dts: Consistently add labels to devicenodes
  ARM: dts: imx6q-sabresd: add volume up/down gpio keys
  ARM: dts: imx53: pinctl update
  ARM: imx: enable cpufreq for imx6q
  ARM: dts: imx6q: enable snvs lp rtc
  ARM: dts: imx6q-sabreauto: Add basic support
  ARM: imx6q: let users input debug uart port number
  ARM: dts: imx53-qsb: Make DA9053 regulator functional
  ARM: dts: imx53-qsb: Use pinctrl for gpio-led
  ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>

From Shawn Guo <shawn.guo@linaro.org>:
It's mxs device tree changes for 3.8.  The majority is device tree
source updates.  One timer improvement and one defconfig update are
also included there.

* tag 'mxs-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs_defconfig: Improve USB related support
  ARM: mxs: apf28dev: Add I2C and SPI support
  ARM: mxs: Setup scheduler clock
  ARM: dts: mxs: Add hog pins to Crystalfontz boards
  ARM: dts: cfa10036: Use pinctrl for power led
  ARM: mxs: apf28dev: Add LCD and backlight support
  ARM: mxs: apf28dev: Add pinctrl and gpios
  ARM: dts: mxs: Add 16 bits LCD screen muxing options for I.MX28
  ARM: dts: cfa10049: Add the DH2228FV DAC to the DTS
  ARM: mxs: Add support for the Armadeus Systems APF28Dev docking board
  ARM: mx28: Skip OCOTP FEC MAC setup if in DT
  ARM: dts: mxs: Add PWM3 muxing options for i.MX28
  ARM: mxs: Add support for the Armadeus Systems APF28 module
  ARM: dts: cfa10049: Add FEC to the CFA-10049 expansion board
  ARM: dts: imx23-olinuxino: Use pinctrl for gpio-led
  ARM: dts: imx23-olinuxino: Remove unneeded "default-on"
  ARM: dts: imx28-evk: Use pinctrl for gpio-led
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Michal Simek <michal.simek@xilinx.com>:

These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.

* 'arm-next' of git://git.xilinx.com/linux-xlnx:
  ARM: zynq: add clk binding support to the ttc
  ARM: zynq: use zynq clk bindings
  clk: Add support for fundamental zynq clks
  ARM: zynq: dts: split up device tree
  ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
  ARM: zynq: dts: add description of the second uart
  ARM: zynq: move arm-specific sys_timer out of ttc
  zynq: move static peripheral mappings
  zynq: remove use of CLKDEV_LOOKUP
  zynq: use pl310 device tree bindings
  zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Enable the HDMI output found on Tamonten Evaluation Carrier boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable the HDMI output found on Plutux boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Hook up the required regulators, I2C DDC adapter and hotplug detect GPIO
to the Tamonten HDMI output. Carrier boards still need to explicitly
enable the output to use it.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable host1x, and the HDMI output. Harmony also has a DVI port with an
HDMI form-factor connector, driven by Tegra's LVDS output. This isn't
enabled yet, due to potential issues with having multiple outputs enabled.

Correct DDC I2C frequency to 100KHz.

Add dummy/fixed regulators to satisfy the HDMI driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
[swarren: add commit description, remove enable of DVI port]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable host1x, and the HDMI output. Harmony also has an optional LCD,
and a VGA output. The former isn't enabled due to potential issues with
having multiple outputs enabled. The latter isn't enabled since the
driver doesn't support VGA yet anyway.

Correct DDC I2C frequency to 100KHz.

Based on work by Thierry Reding for TrimSlice.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

From Sascha Hauer <s.hauer@pengutronix.de>:

ARM i.MX dt updates for 3.8

* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
  Add device tree file for the armadeus apf27
  ARM i.MX: Add Ka-Ro TX25 devicetree
  ARM i.MX25: Add devicetree
  ARM i.MX25: Add devicetree support
  ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Tested on evk-pro3.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Tested on an at91sam9260 board (evk-pro3).
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Tested on an at91sam9260 board (evk-pro3)
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Select the following USB related options:

- USB Ethernet adapter (needed for mx23-olinuxino)
- Native language support (needed for mounting USB pen drives, for example)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM core r2p10 and PL310 r3p2 are integrated on imx6q.  Select
corresponding errata.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

i.MX6Q has 3 revisions 1.0, 1.1 and 1.2.  Print revision on boot.
Signed-off-by: Drew Moseley <drew_moseley@mentor.com>
[drew: add proper error checking for function imx6q_revision()]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Having labels before each node allows board bindings to reference
to nodes by using the &nodename {} notation. This way boards do not
have to resemble the whole devicetree layout. Due to less indention
needed the board files also get better readability. Since the label
make the documentation behind the nodes unnecessary it is removed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add volume up/down gpio keys support in imx6q-sabresd.dts.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch supplements pinctl support on i.MX53.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It enables cpufreq support for imx6q with generic cpufreq-cpu0 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input

Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

imx6q gets 5 uart ports in total.  Different board design may choose
different port as debug uart.  For example, imx6q-sabresd uses UART1,
imx6q-sabrelite uses UART2 and imx6q-arm2 uses UART4.  Rather than
bloating DEBUG_LL choice list with all these uart ports, the patch
introduces DEBUG_IMX6Q_UART_PORT for users to input uart port number
when DEBUG_IMX6Q_UART is selected inside DEBUG_LL choice.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Setup the GPIO7_11 pin as interrupt to the DA9053 and also rename the regulator nodes
so that they match with the datasheet.

This allows probing of DA9053 to succeed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:

leds-gpio leds.2: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>