On the i.MX7D in LPSR mode, the controller will be powered off and the
configuration state is lost after system resume. Upcoming i.MX8QM/QXP
will also completely power off the domain, the controller state is lost
and needs restore, too. So we need to set the pinctrl state again and
re-start chip to re-configuration after resume.

For the wakeup case, it should not set pinctrl to sleep state by
pinctrl_pm_select_sleep_state.

If the interface is down before suspend, we don't need to re-configure
it as it will be configured if the interface is brought up later.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20191204113249.3381-7-qiangqing.zhang@nxp.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Disable clocks while CAN core is in stop mode.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20191210085721.9853-2-qiangqing.zhang@nxp.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.

Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de

commit cdce8448 ("can: flexcan: add vf610 support for FlexCAN")
From above commit by Stefan Agner, the patch just disables
non-correctable errors interrupt and freeze mode. It still can correct
the correctable errors since ECC enabled by default after reset (MECR[ECCDIS]=0,
enable memory error correct) if HW supports ECC.

commit 5e269324 ("can: flexcan: disable completely the ECC mechanism")
From above commit by Joakim Zhang, the patch disables ECC completely (assert
MECR[ECCDIS]) according to the explanation of FLEXCAN_QUIRK_DISABLE_MECR that
disable memory error detection. This cause correctable errors cannot be
corrected even HW supports ECC.

The error correction mechanism ensures that in this 13-bit word, errors
in one bit can be corrected (correctable errors) and errors in two bits can
be detected but not corrected (non-correctable errors). Errors in more than
two bits may not be detected.

If HW supports ECC, we can use this to correct the correctable errors detected
from FlexCAN memory. Then disable non-correctable errors interrupt and freeze
mode to avoid that put FlexCAN in freeze mode.

This patch adds correctable errors correction when HW supports ECC, and
modify explanation for FLEXCAN_QUIRK_DISABLE_MECR.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200416093126.15242-1-qiangqing.zhang@nxp.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CAN FD can transmit up to 8Mbps, but some transceivers only can support
5Mbps, so add check in driver.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20191030064245.12923-2-qiangqing.zhang@nxp.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As the transcevier regulator is optional, this patch switches from
devm_regulator_get() to devm_regulator_get_optional(). This gets rid of "using
dummy regulator" warning message from the regulator core, if no regulator is
available.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-8-mkl@pengutronix.de

As FLEXCAN_ESR_ALL_INT is for all bus errors and state change IRQ
sources, strictly speaking FLEXCAN_ESR_WAK_INT does not belong to these.
So add wakeup interrupt ack separately to existing ack of the
interrupts.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20191204113249.3381-3-qiangqing.zhang@nxp.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch reformats the quirks to get rid of long lines.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-6-mkl@pengutronix.de

This patch documents which registers are not affected by a soft reset of the
flexcan IP core.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-5-mkl@pengutronix.de

This patch adds some new register names and tries to ensure with a
static_assert that the documented offset is correct.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-4-mkl@pengutronix.de

This patch removes a stray empty line from the flexcan_exit_stop_mode()
function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-3-mkl@pengutronix.de

This patch sorts the include files alphabetically.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-2-mkl@pengutronix.de

BCM72113 features a 28nm integrated EPHY, add an entry to the driver for
it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-5.10-20200921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2020-09-21

this is a pull request of 38 patches for net-next.

the first 5 patches are by Colin Ian King, Alexandre Belloni and me and they
fix various spelling mistakes.

The next patch is by me and fixes the indention in the CAN raw protocol
according to the kernel coding style.

Diego Elio Pettenò contributes two patches to fix dead links in CAN's Kconfig.

Masahiro Yamada's patch removes the "WITH Linux-syscall-note" from SPDX tag of
C files.

AThe next 4 patches are by me and target the CAN device infrastructure and add
error propagation and improve the output of various messages to ease driver
development and debugging.

YueHaibing's patch for the c_can driver removes an unused inline function.

Next follows another patch by Colin Ian King, which removes the unneeded
initialization of a variable in the mcba_usb driver.

A patch by me annotates a fallthrough in the mscan driver.

The ti_hecc driver is converted to use devm_platform_ioremap_resource_byname()
in a patch by Dejin Zheng.

Liu Shixin's patch converts the pcan_usb_pro driver to make use of
le32_add_cpu() instead of open coding it.

Wang Hai's patch for the peak_pciefd_main driver removes an unused makro.

Vaibhav Gupta's patch converts the pch_can driver to generic power management.

Stephane Grosjean improves the pcan_usb usb driver by first documenting the
commands sent to the device and by adding support of rxerr/txerr counters.

The next patch is by me and cleans up the Kconfig of the CAN SPI drivers.

The next 6 patches all target the mcp251x driver, they are by Timo Schlüßler,
Andy Shevchenko, Tim Harvey and me. They update the DT bindings documentation,
sort the include files alphabetically, add GPIO support, make use of the
readx_poll_timeout() helper, and add support for half duplex SPI-controllers.

Wolfram Sang contributes a patch to update the contact email address in the
mscan driver, while Zhang Changzhong updates the clock handling.

The next patch is by and updates the rx-offload infrastructure to support
callback less usage.

The last 6 patches add support for the mcp25xxfd CAN SPI driver. First the
dt-bindings are added by Oleksij Rempel, the regmap infrastructure and the main
driver is contributed by me. Kurt Van Dijck adds listen-only support,
Manivannan Sadhasivam adds himself as maintainer, and Thomas Kopp himself as a
reviewer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2020-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This time we have:
 * some AP-side infrastructure for FILS discovery and
   unsolicited probe resonses
 * a major rework of the encapsulation/header conversion
   offload from Felix, to fit better with e.g. AP_VLAN
   interfaces
 * performance fix for VHT A-MPDU size, don't limit to HT
 * some initial patches for S1G (sub 1 GHz) support, more
   will come in this area
 * minor cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/natsemi/ns83820.c: In function ns83820_get_link_ksettings:
drivers/net/ethernet/natsemi/ns83820.c:1210:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]

`tanar` is never used, so remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 37ab4fa7 ("net: unix: allow bind to fail on mutex lock"),
the assignment to err is redundant. So remove it.
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable ALDPS(Advanced Link Down Power Saving) to save power when
link down.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is an off-by-one error in rtl8366rb_is_vlan_valid()
making VLANs 0..4094 valid while it should be 1..4095.
Fix it.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mt7531_cpu_port_config(), if the variable port is neither 5 nor 6,
then variable interface will be used uninitialised. Change the function
to return -EINVAL in this case.

As the return value of mt7531_cpu_port_config() is never checked
(even though it returns an int) add a check in the correct place so that
the error can be passed up the call stack. Now that we correctly handle
errors thrown in this function, also check the return value of
mt7531_mac_config() in case an error occurs here. Also add misisng
checks to mt7530_setup() and mt7531_setup(), which are another level
further up the call stack.

Fixes: c288575f ("net: dsa: mt7530: Add the support of MT7531 switch")
Addresses-Coverity: 1496993 ("Uninitialized variables")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the backlog status in not exposed to user-space.
Since long backlogs (or simply not empty ones) can be a
source of noticeable latency, -RT deployments need some way
to inspect it.

Additionally, there isn't a direct match between 'softnet_stat'
lines and the related CPU - sd for offline CPUs are not dumped -
so this patch also includes the CPU id into such entry.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shay Agroskin says:

====================
Update license and polish ENA driver code

This series adds the following:
- Change driver's license into SPDX format
- Capitalize all log prints in ENA driver
- Fix issues raised by static checkers
- Improve code readability by adding functions, fix spelling
  mistakes etc.
- Update driver's documentation

Changed from previous version:
v1->v2: dropped patch that transforms pr_* log prints into dev_* prints
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCI vendor IDs in the documentation inaccurately describe the ENA
devices. For example, the 1d0f:ec20 can have LLQ support. The driver
loads in LLQ mode by default, and a message is printed to the kernel
ring if the mode isn't supported by the device, so the device table
isn't needed.

Also, LLQ can support various entry sizes, so the documentation is
updated to reflect that.

Interrupt moderation description is also updated to be more accurate.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After running Sparse checker on the driver using
    make C=1 M=drivers/net/ethernet/amazon/ena

the only error that is thrown is:
    sparse: sparse: Using plain integer as NULL pointer
about the line
    struct ena_calc_queue_size_ctx calc_queue_ctx = { 0 };

This patch fixes this warning, thus making our driver free (for now) of
Sparse errors/warnings.

To make a more complete work, this patch also fixes all static warnings
that were found using an internal static checker.
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The formal name changes to "ENA_ADMIN_RSS_INDIRECTION_TABLE_CONFIG".
Indirection is the ability to reference "something" using "something else"
instead of the value itself.
Indirection table, as the name implies, is the ability to reference
CPU/Queue value using hash-to-CPU table instead of CPU/Queue itself.

This patch renames the variable keys_num, which describes the number of
words in the RSS hash key, to key_parts which makes its purpose clearer
in RSS context.
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The placement policy is printed in the process of queue creation in
ena_up(). No need to print it in ena_probe().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Capitalize all log strings printed by the ena driver to make their
format uniform across it.

Also fix indentation, spelling mistakes and comments to improve code
readability. This also includes adding comments to macros/enums whose
purpose might be difficult to understand.
Separate some code into functions to make it easier to understand the
purpose of these lines.
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make log prints in ena_netdev use the same log functions as the rest of
the driver.

For the sake of consistency, all prints in ena_netdev file were
converted into netif_* format except where netdev struct isn't yet
defined. For these places, dev_* log functions are used (similar to
the patch for ena_com files).

This commit leaves some corner cases which would be changed in a
future patch.
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All ena files should now use SPDX format in their license string. This
doesn't change the license of the files, but rather states the same
license in fewer words.

Also update the license years in some of the files.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds Thomas Kopp as a reviewer for the mcp25xxfd CAN driver.
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200916101334.1277-1-thomas.kopp@microchip.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add MAINTAINERS entry for Microchip MCP25XXFD SPI-CAN network driver.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200910133806.25077-7-manivannan.sadhasivam@linaro.orgSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This commit enables listen-only mode, which works internally like CANFD mode.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200918172536.2074504-5-mkl@pengutronix.de

This patch adds support for the Microchip MCP25xxFD SPI CAN controller family.
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200918172536.2074504-4-mkl@pengutronix.de