- 26 Jan, 2016 5 commits
-
-
Antonio Ospite authored
commit dcc7fdbe upstream. v4l2-compliance sends a zeroed struct v4l2_streamparm in v4l2-test-formats.cpp::testParmType(), and this results in a division by 0 in some gspca subdrivers: divide error: 0000 [#1] SMP Modules linked in: gspca_ov534 gspca_main ... CPU: 0 PID: 17201 Comm: v4l2-compliance Not tainted 4.3.0-rc2-ao2 #1 Hardware name: System manufacturer System Product Name/M2N-E SLI, BIOS ASUS M2N-E SLI ACPI BIOS Revision 1301 09/16/2010 task: ffff8800818306c0 ti: ffff880095c4c000 task.ti: ffff880095c4c000 RIP: 0010:[<ffffffffa079bd62>] [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534] RSP: 0018:ffff880095c4fce8 EFLAGS: 00010296 RAX: 0000000000000000 RBX: ffff8800c9522000 RCX: ffffffffa077a140 RDX: 0000000000000000 RSI: ffff880095e0c100 RDI: ffff8800c9522000 RBP: ffff880095e0c100 R08: ffffffffa077a100 R09: 00000000000000cc R10: ffff880067ec7740 R11: 0000000000000016 R12: ffffffffa07bb400 R13: 0000000000000000 R14: ffff880081b6a800 R15: 0000000000000000 FS: 00007fda0de78740(0000) GS:ffff88012fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000014630f8 CR3: 00000000cf349000 CR4: 00000000000006f0 Stack: ffffffffa07a6431 ffff8800c9522000 ffffffffa077656e 00000000c0cc5616 ffff8800c9522000 ffffffffa07a5e20 ffff880095e0c100 0000000000000000 ffff880067ec7740 ffffffffa077a140 ffff880067ec7740 0000000000000016 Call Trace: [<ffffffffa07a6431>] ? v4l_s_parm+0x21/0x50 [videodev] [<ffffffffa077656e>] ? vidioc_s_parm+0x4e/0x60 [gspca_main] [<ffffffffa07a5e20>] ? __video_do_ioctl+0x280/0x2f0 [videodev] [<ffffffffa07a5ba0>] ? video_ioctl2+0x20/0x20 [videodev] [<ffffffffa07a59b9>] ? video_usercopy+0x319/0x4e0 [videodev] [<ffffffff81182dc1>] ? page_add_new_anon_rmap+0x71/0xa0 [<ffffffff811afb92>] ? mem_cgroup_commit_charge+0x52/0x90 [<ffffffff81179b18>] ? handle_mm_fault+0xc18/0x1680 [<ffffffffa07a15cc>] ? v4l2_ioctl+0xac/0xd0 [videodev] [<ffffffff811c846f>] ? do_vfs_ioctl+0x28f/0x480 [<ffffffff811c86d4>] ? SyS_ioctl+0x74/0x80 [<ffffffff8154a8b6>] ? entry_SYSCALL_64_fastpath+0x16/0x75 Code: c7 93 d9 79 a0 5b 5d e9 f1 f3 9a e0 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 53 31 d2 48 89 fb 48 83 ec 08 8b 46 10 <f7> 76 0c 80 bf ac 0c 00 00 00 88 87 4e 0e 00 00 74 09 80 bf 4f RIP [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534] RSP <ffff880095c4fce8> ---[ end trace 279710c2c6c72080 ]--- Following what the doc says about a zeroed timeperframe (see http://www.linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-parm.html): ... To reset manually applications can just set this field to zero. fix the issue by resetting the frame rate to a default value in case of an unusable timeperframe. The fix is done in the subdrivers instead of gspca.c because only the subdrivers have notion of a default frame rate to reset the camera to. Signed-off-by:
Antonio Ospite <ao2@ao2.it> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Hans Verkuil authored
commit 4623e596 upstream. In the 3.17 kernel the poll() behavior changed for output streams: as long as not all buffers were queued up poll() would return that userspace can write. This is fine for the write() call, but when using stream I/O this changed the behavior since the expectation was that it would wait for buffers to become available for dequeuing. This patch only enables the check whether you can queue buffers for file I/O only, and skips it for stream I/O. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Vito Caputo authored
commit e4ad29fa upstream. Rather than always allocating the high-order XATTR_SIZE_MAX buffer which is costly and prone to failure, only allocate what is needed and realloc if necessary. Fixes https://github.com/coreos/bugs/issues/489Signed-off-by:
Miklos Szeredi <miklos@szeredi.hu> Signed-off-by:
-
Miklos Szeredi authored
commit 97daf8b9 upstream. When ovl_copy_xattr() encountered a zero size xattr no more xattrs were copied and the function returned success. This is clearly not the desired behavior. Signed-off-by:
-
Hans de Goede authored
commit 0a363e85 upstream. MSI interrupts appear to not work for nv46 based cards. Change the mc subdev oclass for these cards from nv44 to nv4c, the nv4c mc code is identical to the nv44 mc code except that it does not use msi (it does not define a msi_rearm callback). BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=90435Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
- 19 Jan, 2016 35 commits
-
-
Kamal Mostafa authored
Signed-off-by: -
Francesco Ruggeri authored
commit 07a5d384 upstream. dst_release should not access dst->flags after decrementing __refcnt to 0. The dst_entry may be in dst_busy_list and dst_gc_task may dst_destroy it before dst_release gets a chance to access dst->flags. Fixes: d69bbf88 ("net: fix a race in dst_release()") Fixes: 27b75c95 ("net: avoid RCU for NOCACHE dst") Signed-off-by:
Francesco Ruggeri <fruggeri@arista.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 093e5840 upstream. In the following commit: 76751049 ("sched: Implement lockless wake-queues") we gained lockless wake-queues. The -RT kernel managed to lockup itself with those. There could be multiple attempts for task X to enqueue it for a wakeup _even_ if task X is already running. The reason is that task X could be runnable but not yet on CPU. The the task performing the wakeup did not leave the CPU it could performe multiple wakeups. With the proper timming task X could be running and enqueued for a wakeup. If this happens while X is performing a fork() then its its child will have a !NULL `wake_q` member copied. This is not a problem as long as the child task does not participate in lockless wakeups :) Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 76751049 ("sched: Implement lockless wake-queues") Link: http://lkml.kernel.org/r/20151221171710.GA5499@linutronix.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Rabin Vincent authored
commit 55795ef5 upstream. The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data instructions since it XORs A with X while all the others replace A with some loaded value. All the BPF JITs fail to clear A if this is used as the first instruction in a filter. This was found using american fuzzy lop. Add a helper to determine if A needs to be cleared given the first instruction in a filter, and use this in the JITs. Except for ARM, the rest have only been compile-tested. Fixes: 34805931 ("net: filter: get rid of BPF_S_* enum") Signed-off-by:
Rabin Vincent <rabin@rab.in> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
John Fastabend authored
commit 73c20a8b upstream. When a qdisc is using per cpu stats (currently just the ingress qdisc) only the bstats are being freed. This also free's the qstats. Fixes: b0ab6f92 ("net: sched: enable per cpu qstats") Signed-off-by:
John Fastabend <john.r.fastabend@intel.com> Acked-by:
-
Charles Keepax authored
commit 783513ee upstream. snd_soc_dapm_mutex_lock currently uses the un-nested call which can cause lockdep warnings when called from control handlers (a relatively common usage) and using modules. As creating the control causes a potential mutex inversion with the handler, creating the control will take the controls_rwsem under the dapm_mutex and accessing the control will take the dapm_mutex under controls_rwsem. All the users look like they want to be using the runtime class of the lock anyway, so this patch just changes snd_soc_dapm_mutex_lock to use the nested call, with the SND_SOC_DAPM_CLASS_RUNTIME class. Fixes: f6d5e586 ("ASoC: dapm: Add helpers to lock/unlock DAPM mutex") Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Paolo Bonzini authored
commit e5e57e7a upstream. While setting the KVM PIT counters in 'kvm_pit_load_count', if 'hpet_legacy_start' is set, the function disables the timer on channel[0], instead of the respective index 'channel'. This is because channels 1-3 are not linked to the HPET. Fix the caller to only activate the special HPET processing for channel 0. Reported-by:
P J P <pjp@fedoraproject.org> Fixes: 0185604cSigned-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Andrea Arcangeli authored
commit ff4319dc upstream. The dmi_ver wasn't updated correctly before the dmi_decode method run to save the uuid. That resulted in "dmidecode -s system-uuid" and /sys/class/dmi/id/product_uuid disagreeing. The latter was buggy and this fixes it. Reported-by:
Federico Simoncelli <fsimonce@redhat.com> Fixes: 9f9c9cbb ("drivers/firmware/dmi_scan.c: fetch dmi version from SMBIOS if it exists") Fixes: 79bae42d ("dmi_scan: refactor dmi_scan_machine(), {smbios,dmi}_present()") Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
Jean Delvare <jdelvare@suse.de> Signed-off-by:
-
Michal Hocko authored
commit 751e5f5c upstream. kernel test robot has reported the following crash: BUG: unable to handle kernel NULL pointer dereference at 00000100 IP: [<c1074df6>] __queue_work+0x26/0x390 *pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53 Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe5 #1 Workqueue: events vmstat_shepherd task: cb684600 ti: cb7ba000 task.ti: cb7ba000 EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0 EIP is at __queue_work+0x26/0x390 EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000 ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0 Stack: Call Trace: __queue_delayed_work+0xa1/0x160 queue_delayed_work_on+0x36/0x60 vmstat_shepherd+0xad/0xf0 process_one_work+0x1aa/0x4c0 worker_thread+0x41/0x440 kthread+0xb0/0xd0 ret_from_kernel_thread+0x21/0x40 The reason is that start_shepherd_timer schedules the shepherd work item which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates that workqueue so if the further initialization takes more than HZ we might end up scheduling on a NULL vmstat_wq. This is really unlikely but not impossible. Fixes: 373ccbe5 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress") Reported-by:
kernel test robot <ying.huang@linux.intel.com> Signed-off-by:
Michal Hocko <mhocko@suse.com> Tested-by:
Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 049fb9bd upstream. If the module init code fails after calling ftrace_module_init() and before calling do_init_module(), we can suffer from a memory leak. This is because ftrace_module_init() allocates pages to store the locations that ftrace hooks are placed in the module text. If do_init_module() fails, it still calls the MODULE_GOING notifiers which will tell ftrace to do a clean up of the pages it allocated for the module. But if load_module() fails before then, the pages allocated by ftrace_module_init() will never be freed. Call ftrace_release_mod() on the module if load_module() fails before getting to do_init_module(). Link: http://lkml.kernel.org/r/567CEA31.1070507@intel.comReported-by:
"Qiu, PeiyangX" <peiyangx.qiu@intel.com> Fixes: a949ae56 "ftrace/module: Hardcode ftrace_module_init() call into load_module()" Acked-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Roman Volkov authored
commit 0f090bf1 upstream. Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver is already in the kernel, this node enables the controller support for WM8650 Signed-off-by:
Roman Volkov <rvolkov@v1ros.org> Reviewed-by:
Alexey Charkov <alchark@gmail.com> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
NeilBrown authored
commit b02bab6b upstream. These async_XX functions are called from md/raid5 in an atomic section, between get_cpu() and put_cpu(), so they must not sleep. So use GFP_NOWAIT rather than GFP_IO. Dan Williams writes: Longer term async_tx needs to be merged into md directly as we can allocate this unmap data statically per-stripe rather than per request. Fixed: 7476bd79 ("async_pq: convert to dmaengine_unmap_data") Reported-and-tested-by:
Stanislav Samsonov <slava@annapurnalabs.com> Acked-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Linus Walleij authored
commit 20f12758 upstream. Commit 0976c946 "arm/versatile: Fix versatile irq specifications" has an off-by-one error on the Versatile AB that has been regressing the Versatile AB hardware for some time. However it seems like the interrupt assignments have never been correct and I have now adjusted them according to the specification. The masks for the valid interrupts made it impossible to assign the right SIC interrupt for the MMCI, so I went in and fixed these to correspond to the specifications, and added references if anyone wants to double-check. Due to the Versatile PB including the Versatile AB as a base DTS file, we need to override and correct some values to correspond to the actual changes in the hardware. For the Versatile PB I don't think the IRQ line assignment for MMCI has ever been correct for either of the two MMCI blocks. It would be nice if someone with the physical PB board could test this. Patch tested on the Versatile AB, QEMU for Versatile AB and QEMU for Versatile PB. Cc: Rob Herring <robh@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Fixes: 0976c946 ("arm/versatile: Fix versatile irq specifications") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Tony Lindgren authored
commit e7b11dc7 upstream. Commit 63aa945b ("memory: omap-gpmc: Add Kconfig option for debug") unified the GPMC debug for the SoCs with GPMC. The commit also left out the option for HWMOD_INIT_NO_RESET as we now require proper timings for GPMC to be able to remap GPMC devices out of address 0. Unfortunately on Nokia N900, onenand now only partially works with the device tree provided timings. It works enough to get detected but the clock rate supported by the onenand chip gets misdetected. This in turn causes the GPMC timings to be miscalculated and this leads into file system corruption on N900. Looks like onenand needs CS_CONFIG1 bit 27 WRITETYPE set for for sync write. This is needed also for async timings when we write to onenand with omap2_onenand_set_async_mode(). Without sync write bit set, the async read for the onenand ONENAND_REG_VERSION_ID will return 0xfff. Let's exit with an error if onenand rate is not detected. And let's remove the extra call to omap2_onenand_set_async_mode() as we only need to do this once at the end of omap2_onenand_setup_async(). Fixes: 63aa945b ("memory: omap-gpmc: Add Kconfig option for debug") Reported-by:
Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Tested-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Chris Metcalf authored
commit c1b27ab5 upstream. This allows the build system to know that it can't attempt to configure the Lustre virtual block device, for example, when tilepro is using 64KB pages (as it does by default). The tilegx build already provided those symbols. Previously we required that the tilepro hypervisor be rebuilt with a different hardcoded page size in its headers, and then Linux be rebuilt using the updated hypervisor header. Now we allow each of the hypervisor and Linux to be built independently. We still check at boot time to ensure that the page size provided by the hypervisor matches what Linux expects. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
Qiu Peiyang authored
commit f36d1be2 upstream. When we do cat /sys/kernel/debug/tracing/printk_formats, we hit kernel panic at t_show. general protection fault: 0000 [#1] PREEMPT SMP CPU: 0 PID: 2957 Comm: sh Tainted: G W O 3.14.55-x86_64-01062-gd4acdc7 #2 RIP: 0010:[<ffffffff811375b2>] [<ffffffff811375b2>] t_show+0x22/0xe0 RSP: 0000:ffff88002b4ebe80 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000004 RDX: 0000000000000004 RSI: ffffffff81fd26a6 RDI: ffff880032f9f7b1 RBP: ffff88002b4ebe98 R08: 0000000000001000 R09: 000000000000ffec R10: 0000000000000000 R11: 000000000000000f R12: ffff880004d9b6c0 R13: 7365725f6d706400 R14: ffff880004d9b6c0 R15: ffffffff82020570 FS: 0000000000000000(0000) GS:ffff88003aa00000(0063) knlGS:00000000f776bc40 CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033 CR2: 00000000f6c02ff0 CR3: 000000002c2b3000 CR4: 00000000001007f0 Call Trace: [<ffffffff811dc076>] seq_read+0x2f6/0x3e0 [<ffffffff811b749b>] vfs_read+0x9b/0x160 [<ffffffff811b7f69>] SyS_read+0x49/0xb0 [<ffffffff81a3a4b9>] ia32_do_call+0x13/0x13 ---[ end trace 5bd9eb630614861e ]--- Kernel panic - not syncing: Fatal exception When the first time find_next calls find_next_mod_format, it should iterate the trace_bprintk_fmt_list to find the first print format of the module. However in current code, start_index is smaller than *pos at first, and code will not iterate the list. Latter container_of will get the wrong address with former v, which will cause mod_fmt be a meaningless object and so is the returned mod_fmt->fmt. This patch will fix it by correcting the start_index. After fixed, when the first time calls find_next_mod_format, start_index will be equal to *pos, and code will iterate the trace_bprintk_fmt_list to get the right module printk format, so is the returned mod_fmt->fmt. Link: http://lkml.kernel.org/r/5684B900.9000309@intel.com Fixes: 102c9323 "tracing: Add __tracepoint_string() to export string pointers" Signed-off-by:
-
Colin Ian King authored
commit 713a3e4d upstream. Fix build warning: scripts/recordmcount.c:589:4: warning: format not a string literal and no format arguments [-Wformat-security] sprintf("%s: failed\n", file); Fixes: a50bd439 ("ftrace/scripts: Have recordmcount copy the object file") Link: http://lkml.kernel.org/r/1451516801-16951-1-git-send-email-colin.king@canonical.com Cc: Li Bin <huawei.libin@huawei.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Hui Wang authored
commit c7b60a89 upstream. Then users can remap the keycode from userspace. If without the remap, the input device will pass KEY_MICMUTE to userspace, but in X11 layer, it uses KEY_F20 rather than KEY_MICMUTE for XF86AudioMicMute. After adding the keycode map, users can remap the keycode to any value users want. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kailang authored
commit 3694cb29 upstream. The Lenovo ThinkCenter AIO uses Line2 (NID 0x1b) to implement the micmute hotkey, here we register an input device and use Line2 unsol event to collect the hotkey pressing or releasing. In the meanwhile, the micmute led is controlled by GPIO2, so we use an existing function alc_fixup_gpio_mic_mute_hook() to control the led. [Hui: And there are two places to register the input device, to make the code simple and clean, move the two same code sections into a function.] Signed-off-by:
Kailang <kailang@realtek.com> Signed-off-by:
-
Nikesh Oswal authored
commit e73694d8 upstream. For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as we test for a multiple of 8kHz. This patch fixes this issue by testing for multiples of 4kHz instead. Signed-off-by:
Nikesh Oswal <Nikesh.Oswal@cirrus.com> Signed-off-by:
-
David Vrabel authored
commit d8c98a1d upstream. Adding the rtc platform device in non-privileged Xen PV guests causes an IRQ conflict because these guests do not have legacy PIC and may allocate irqs in the legacy range. In a single VCPU Xen PV guest we should have: /proc/interrupts: CPU0 0: 4934 xen-percpu-virq timer0 1: 0 xen-percpu-ipi spinlock0 2: 0 xen-percpu-ipi resched0 3: 0 xen-percpu-ipi callfunc0 4: 0 xen-percpu-virq debug0 5: 0 xen-percpu-ipi callfuncsingle0 6: 0 xen-percpu-ipi irqwork0 7: 321 xen-dyn-event xenbus 8: 90 xen-dyn-event hvc_console ... But hvc_console cannot get its interrupt because it is already in use by rtc0 and the console does not work. genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (rtc0) We can avoid this problem by realizing that unprivileged PV guests (both Xen and lguests) are not supposed to have rtc_cmos device and so adding it is not necessary. Privileged guests (i.e. Xen's dom0) do use it but they should not have irq conflicts since they allocate irqs above legacy range (above gsi_top, in fact). Instead of explicitly testing whether the guest is privileged we can extend pv_info structure to include information about guest's RTC support. Reported-and-tested-by:
Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: vkuznets@redhat.com Cc: xen-devel@lists.xenproject.org Cc: konrad.wilk@oracle.com Link: http://lkml.kernel.org/r/1449842873-2613-1-git-send-email-boris.ostrovsky@oracle.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Ashok Raj authored
commit d90167a9 upstream. Intel's MCA implementation broadcasts MCEs to all CPUs on the node. This poses a problem for offlined CPUs which cannot participate in the rendezvous process: Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler Kernel Offset: disabled Rebooting in 100 seconds.. More specifically, Linux does a soft offline of a CPU when writing a 0 to /sys/devices/system/cpu/cpuX/online, which doesn't prevent the #MC exception from being broadcasted to that CPU. Ensure that offline CPUs don't participate in the MCE rendezvous and clear the RIP valid status bit so that a second MCE won't cause a shutdown. Without the patch, mce_start() will increment mce_callin and wait for all CPUs. Offlined CPUs should avoid participating in the rendezvous process altogether. Signed-off-by:
Ashok Raj <ashok.raj@intel.com> [ Massage commit message. ] Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Tony Luck <tony.luck@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/1449742346-21470-2-git-send-email-bp@alien8.deSigned-off-by:
-
Thomas Gleixner authored
commit abc7e40c upstream. If a interrupt chip utilizes chip->buslock then free_irq() can deadlock in the following way: CPU0 CPU1 interrupt(X) (Shared or spurious) free_irq(X) interrupt_thread(X) chip_bus_lock(X) irq_finalize_oneshot(X) chip_bus_lock(X) synchronize_irq(X) synchronize_irq() waits for the interrupt thread to complete, i.e. forever. Solution is simple: Drop chip_bus_lock() before calling synchronize_irq() as we do with the irq_desc lock. There is nothing to be protected after the point where irq_desc lock has been released. This adds chip_bus_lock/unlock() to the remove_irq() code path, but that's actually correct in the case where remove_irq() is called on such an interrupt. The current users of remove_irq() are not affected as none of those interrupts is on a chip which requires buslock. Reported-by:
Fredrik Markström <fredrik.markstrom@gmail.com> Signed-off-by:
-
James Morse authored
commit 1d5cda40 upstream. mmdebug.h uses BUILD_BUG_ON_INVALID(), assuming someone else included linux/bug.h. Include it ourselves. This saves build-failures such as: arch/arm64/include/asm/pgtable.h: In function 'set_pte_at': arch/arm64/include/asm/pgtable.h:281:3: error: implicit declaration of function 'BUILD_BUG_ON_INVALID' [-Werror=implicit-function-declaration] VM_WARN_ONCE(!pte_young(pte), Fixes: 02602a18 ("bug: completely remove code generated by disabled VM_BUG_ON()") Signed-off-by:
James Morse <james.morse@arm.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Tobias Klauser authored
commit 20b08e1a upstream. mdiobus_alloc() might return NULL, but its return value is not checked in mdio_mux_init(). This could potentially lead to a NULL pointer dereference. Fix it by checking the return value Fixes: 0ca2997d ("netdev/of/phy: Add MDIO bus multiplexer support.") Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
-
Peter Ujfalusi authored
commit 27bc944c upstream. f9317829 dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer Fixed the memleak, but introduced another issue: the terminate_all callback might be called with interrupts disabled and the dma_free_coherent() is not allowed to be called when IRQs are disabled. Convert the driver to use dma_pool_* for managing the list of control blocks for the transfer. Fixes: f9317829 ("dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer") Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
-
Dan Carpenter authored
commit 389e4e04 upstream. The problem here is that at the end of the loop we test for if idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a post-op, it actually ends up set to (u8)-1. I have fixed this by moving the decrement inside the loop. Fixes: 486a5bc7 ('qlcnic: Add support for 83xx suspend and resume.') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Sergei Shtylyov authored
commit 3e230993 upstream. For the little-endian SH771x kernels the driver has to byte-swap the RX/TX buffers, however yet unset physcial address from the TX descriptor is used to call sh_eth_soft_swap(). Use 'skb->data' instead... Fixes: 31fcb99d ("net: sh_eth: remove __flush_purge_region") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Dan Carpenter authored
commit 40d24c4d upstream. There are two issue here. 1) cnt starts as maxloop + 1 so all these loops iterate one more time than intended. 2) At the end of the loop we test for "if (maxloop && !cnt)" but for the first two loops, we end with cnt equal to -1. Changing this to a pre-op means we end with cnt set to 0. Fixes: cae86d4a ('mISDN: Add driver for Infineon ISDN chipset family') Signed-off-by:
-
Stefan Wahren authored
commit 4c02cba1 upstream. Currently the provided initial value for bcm2835_gpio_direction_output has no effect. So fix this issue by changing the value before changing the GPIO direction. As a result we need to move the function below bcm2835_gpio_set. Suggested-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Eric Anholt <eric@anholt.net> Acked-by:
Stephen Warren <swarren@wwwdotorg.org> Fixes: e1b2dc70 ("pinctrl: add bcm2835 driver") Signed-off-by:
-
Tilman Schmidt authored
commit 4c5e354a upstream. When shutting down the device, the struct ser_cardstate must not be kfree()d immediately after the call to platform_device_unregister() since the embedded struct platform_device is still in use. Move the kfree() call to the release method instead. Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Fixes: 2869b23e ("drivers/isdn/gigaset: new M101 driver (v2)") Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
WANG Cong authored
commit 5449a5ca upstream. When sysctl performs restrict writes, it allows to write from a middle position of a sysctl file, which requires us to initialize the table data before calling proc_dostring() for the write case. Fixes: 3d1bec99 ("ipv6: introduce secret_stable to ipv6_devconf") Reported-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Tested-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Nikolay Borisov authored
commit 639e077b upstream. Commit 3bfe0498 ("netfilter: nfnetlink_{log,queue}: Register pernet in first place") reorganised the initialisation order of the pernet_subsys to avoid "use-before-initialised" condition. However, in doing so the cleanup logic in nfnetlink_queue got botched in that the pernet_subsys wasn't cleaned in case nfnetlink_subsys_register failed. This patch adds the necessary cleanup routine call. Fixes: 3bfe0498 ("netfilter: nfnetlink_{log,queue}: Register pernet in first place") Signed-off-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> [ kamal: backport to 4.2-stable: appled to nfnetlink_queue_core.c ] Signed-off-by:
-
Hannes Frederic Sowa authored
commit 7bbadd2d upstream. Docbook does not like the definition of macros inside a field declaration and adds a warning. Move the definition out. Fixes: 79462ad0 ("net: add validation for the socket syscall protocol argument") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
-
Masahiro Yamada authored
commit 7be047e0 upstream. The register offset must be shifted by regshift, otherwise the baudrate is not set. I missed the issue probably because the divisor register was already set by the boot loader. Fixes: 1a8d2903 ("serial: 8250_uniphier: add UniPhier serial driver") Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
