Needed for proper i2c over aux handling for certain
monitors and configurations (e.g., dp bridges or
adapters).

v2: add comments clarifying tx_size setting.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>

To support bare address requests used by the drm dp helpers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Loading cursors to the LCD controller's SRAM can be corrupted when the
configured pixel clock is relatively slow.  This seems to be caused
when we write back-to-back to the SRAM registers.

There doesn't appear to be any status register we can read to check
when an access has completed.

Inserting a dummy read between the writes appears to fix the problem.

Cc: <stable@vger.kernel.org> # 3.13
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

 Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)

Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
  not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
  patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things

* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
  Skip intel_crt_init for Dell XPS 8700
  drm/i915: vlv: fix RPS interrupt mask setting
  Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
  drm/i915: move power domain init earlier during system resume
  drm/i915: Fix the computation of required fb size for pipe
  drm/i915: don't get/put runtime PM at the debugfs forcewake file
  drm/i915: fix WARNs when reading DDI state while suspended
  drm/i915: don't read cursor registers on powered down pipes
  drm/i915: get runtime PM at i915_display_info
  drm/i915: don't read pp_ctrl_reg if we're suspended
  drm/i915: get runtime PM at i915_reg_read_ioctl
  drm/i915: don't schedule force_wake_timer at gen6_read
  drm/i915: vlv: reserve the GT power context only once during driver init
  drm/i915: prefer struct drm_i915_private to drm_i915_private_t
  drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
  drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
  drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
  drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
  drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
  drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
  ...

drm/tegra: Changes for v3.15-rc1

Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.

A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.

Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.

* tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/tegra: Use standard GPL v2 license text
  drm/tegra: Relicense under GPL v2
  drm/tegra: Relicense public header under MIT
  drm/tegra: Add eDP support
  gpu: host1x: export host1x_syncpt_incr_max() function
  drm/tegra: prime: Add vmap support

drm/panel: Changes for v3.15-rc1

Add support for a couple more simple panels. A few cleanups to the
simple panel driver are also included (gpiod interface conversion,
removal of redundant call to regulator_disable()).

* tag 'drm/panel/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/panel: add support for LG LD070WX3-SL01 panel
  drm/panel: add support for LG LH500WX1-SD03 panel
  drm/panel: simple: Allow DSI panels to provide mode flags
  drm/panel: simple: Allow GPIO accesses to sleep
  drm/panel: remove redundant regulator_disable()
  drm/panel: use gpiod interface for enable GPIO
  drm/panel: Add LG 12.9" LCD panel
  MAINTAINERS: Add entry for DRM panel drivers

Conflicts:
	MAINTAINERS

Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

Summaries:
- Add MIPI-DSI Driver, and dt bindigs
- Add S6E8AA0 MIPI-DSI based panel drivers, and dt bindings
- Add LD9040 parallel panel driver
 . this driver is placed in drivers/gpu/drm/panel, and it seems
   to be used for exynos drm as of now,
- Some fixups

Changelog v2:
- Remove super device support, and relevant dt bindings for more reviews.
- Fix module build errors you pointed out.
- Re-based it to drm-next again.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/bridge: export ptn3460_init function
  drm/exynos: remove MODULE_DEVICE_TABLE definitions
  ARM: dts: exynos4412-trats2: enable exynos/fimd node
  ARM: dts: exynos4210-trats: enable exynos/fimd node
  ARM: dts: exynos4412-trats2: add panel node
  ARM: dts: exynos4210-trats: add panel node
  ARM: dts: exynos4: add MIPI DSI Master node
  drm/panel: add S6E8AA0 driver
  ARM: dts: exynos4210-universal_c210: add proper panel node
  drm/panel: add ld9040 driver
  panel/ld9040: add DT bindings
  panel/s6e8aa0: add DT bindings
  drm/exynos: add DSIM driver
  exynos/dsim: add DT bindings
  drm/exynos: disallow fbdev initialization if no device is connected
  drm/mipi_dsi: create dsi devices only for nodes with reg property
  drm/mipi_dsi: add flags to DSI messages

Pull request of 2014-04-04

The second vmwgfx pull request for the 3.15 merge window.
Contains a fbdev fix by Christopher Friedt, one fix for a locking order
violation introduced in 3.14 (hit when using queries) and finally a
removal of the DRM_AUTH requirement around some vmwgfx IOCTLS where the
caller is already required to have an open handle to the object.

* tag 'vmwgfx-next-2014-04-04' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: correct fb_fix_screeninfo.line_length
  drm/vmwgfx: Remove authorization requirements around some more ioctls
  drm/vmwgfx: Fix query buffer locking order violation

Pull request of 2014-04-04

Currently only a single patch fixing up mixed use of the ttm_bo_reserve and
ww_mutex APIs

* tag 'ttm-next-2014-04-04' of git://people.freedesktop.org/~thomash/linux:
  drm/ttm: Hide the implementation details of reservation

If we get a msg.reply of REPLY_DEFER, we also get an err of 0
so we fail reads with 0 < size and return -EPROTO instead of trying
again.

v2: same fix in i2c code.

Found writing MST support.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This patch exports ptn3460_init function so that other modules
can call this function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

This patch removes MODULE_DEVICE_TABLE definition to of_device_id
of DP and MIPI-DSI drivers.

Eyxnos drm should be built as single module so these definitions
should be removed.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

The patch changes fimd node status to OK.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch changes fimd node status to OK.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats2.
It adds also trats2 specific properties for DSI
and regulator required by panel.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats.
It adds also trats specific properties for DSI.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This is a common part of DSI node for all Exynos4 boards.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds MIPI-DSI based S6E8AA0 AMOLED LCD panel driver.
Driver uses mipi_dsi bus to communicate with panel and exposes drm_panel
interface.

v2
- added bus error handling,
- set maxmimum DSI packet size on init,
- removed unsupported brightness drm_panel callbacks,
- minor improvements

v3
- switched to gpiod framework,
- minor fixes in error handling
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch replaces panel bindings for panel initialized by boot loader
with bindings to proper ld9040 panel.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds LD9040 parallel RGB panel driver with SPI control interface.
The driver uses drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds bindings for ld9040 panel.
Bindings describe panel resources, boot delays,
display timings and physical size.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds bindings for s6e8aa0 panel.
Bindings describes panel resources, boot delays,
display timings, orientation and physical size.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds driver for Exynos DSI master (DSIM). It is a platform driver
which is registered as exynos_drm_display sub-driver of exynos_drm framework
and implements DRM encoder/connector pair.
It is also MIPI-DSI host driver and provides DSI bus for panels.
It interacts with its panel(s) using drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds DT bindings for Exynos DSI Master. DSIM follows rules
for DSI bus host bindings [1].
Properties describes its resources: memory, interrupt, clocks,
phy, regulators, frequencies of clocks and video interfaces.

[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds explicit check if there is a connector with
connected status before fbdev initialization. It prevents creation
of default fbdev 1024x768 which is unusable on panels with bigger resolutions.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

MIPI DSI host node can contain child nodes which are not DSI devices.
Checking for existence of reg property can be used to distinguish such nodes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds flags field to mipi_dsi_msg structure and two flags:
- MIPI_DSI_MSG_REQ_ACK - request ACK from peripheral for given message,
- MIPI_DSI_MSG_USE_LPM - use Low Power Mode to transmit message.
The first flag is usually helpful during DSI diagnostic, the second
flag is required by some peripherals during configuration phase.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The Dell XPS 8700 has a onboard Display port and HDMI port and no VGA port.
The call intel_crt_init freeze the machine, so skip such call.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73559
Signed-off-by: Giacomo Comes <comes at naic.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This typo may lead to missed RPS interrupts and as a result a too
low or too high frequency for the current workload. The interrupt mask
will be set properly at a subsequent GPU idle event, but can get
corrupted again at the next RPS up/down event.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

As per the inputs provided by hardware team  we still use DDR
Rates as 0,1=800, 2=1066, 3=1333.
With this change, Turbo freqs used on current machines matches.

This reverts commit f64a28a7.

commit f64a28a7
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Mon Nov 4 16:07:00 2013 -0800

     drm/i915/vlv: fixup DDR freq detection per Punit spec

v2: Add reference to previous commit which changed this. (Daniel)
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

During resume the intel hda audio driver depends on the i915 driver
reinitializing the audio power domain. Since the order of calling the
i915 resume handler wrt. that of the audio driver is not guaranteed,
move the power domain reinitialization step to the resume_early
handler. This is guaranteed to run before the resume handler of any
other driver.

The power domain initialization in turn requires us to enable the i915
pci device first, so move that part earlier too.

Accordingly disabling of the i915 pci device should happen after the
audio suspend handler ran. So move the disabling later from the i915
resume handler to the resume_late handler.

v2:
- move intel_uncore_sanitize/early_sanitize earlier too, so they don't
  get reordered wrt. intel_power_domains_init_hw()

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76152Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable and loud comments that this is just a hack.]
[danvet: Fix "Should it be static?" sparse warning reported by Wu
Fengguang's kbuilder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Use the more canonical and concise variant of the GPL v2 license text.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This file will eventually be exported to libdrm, where all the public
header files use the MIT license.
Reported-by: Erik Faye-Lund <kusmabite@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra V4L2 camera driver needs this function to do frame capture.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This is trivial to support since all GEM objects are mapped into kernel
space anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This panel is used by Tegra Note 7 and supported by the simple-panel
driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This panel is used by the NVIDIA SHIELD and supported by the
simple-panel driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>