Merge tag 'v5.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt

Pin-name corrections for Veyron-Fievel, bluetooth for a number of veyron boards and
additional operating points for rk3288-tinker.

* tag 'v5.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: Use ABI name for recovery mode pin on veyron fievel/tiger
  ARM: dts: rockchip: Use ABI name for write protect pin on veyron fievel/tiger
  ARM: dts: rockchip: Add missing cpu operating points for rk3288-tinker
  ARM: dts: rockchip: Add brcm bluetooth for rk3288-veyron

Link: https://lore.kernel.org/r/8215452.dU6eVM2tAM@philSigned-off-by: Olof Johansson <olof@lixom.net>

This enables the driver for STM32 PWR regulators found on stm32mp1.

Link: https://lore.kernel.org/r/20200109125531.13610-1-alexandre.torgue@st.comSigned-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'stm32-dt-for-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.6, round 1

Highlights:
----------

MPU part:
 -Add PWM support on DK2 board.
 -Add counter support to STM32 timers.
 -Add support of SDMMC 2&3 instances based on "arm,pl18x". SDMMC2 is
  connected to eMMC on ED1 board. SDMMC3 is connected to the GPIO
  extension connector on EV1 & DKx boards.
 -Add ADC support on ED1 board.
 -Update devicetree files split to better fit to STM32MP15 SOC & boards
  diversity.
 -Fix issues seen during YAML validation.
 -Enable Ethernet (MAC) TX clock gating during low-power mode.
 -Enable USB OTG HS support on DKx boards.
 -Enable USB Host EHCI on DKx boards.

MCU part:
 -Fix issues seen during YAML validation.

* tag 'stm32-dt-for-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (37 commits)
  ARM: dts: stm32: Add power-supply for RGB panel on stm32429i-eval
  ARM: dts: stm32: Add power-supply for DSI panel on stm32f469-disco
  ARM: dts: stm32: change nvmem node name on stm32mp1
  ARM: dts: stm32: change nvmem node name on stm32f429
  ARM: dts: stm32: update mlahb node according to the bindings on stm32mp15
  ARM: dts: stm32: fix dma controller node name on stm32mp157c
  ARM: dts: stm32: fix dma controller node name on stm32f743
  ARM: dts: stm32: fix dma controller node name on stm32f746
  ARM: dts: stm32: add phy-names to usbotg_hs on stm32mp157c-ev1
  ARM: dts: stm32: enable USB OTG HS on stm32mp15 DKx boards
  ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp15 DKx
  ARM: dts: stm32: enable USBPHYC on stm32mp15 DKx boards
  ARM: dts: stm32: remove useless clock-names from RTC node on stm32f746
  ARM: dts: stm32: remove useless clock-names from RTC node on stm32f429
  ARM: dts: stm32: Enable MAC TX clock gating during TX low-power mode on stm32mp15
  ARM: dts: stm32: adjust slew rate for Ethernet on stm32mp15
  ARM: dts: stm32: remove syscfg clock on stm32mp15 ethernet
  ARM: dts: stm32: remove "@" and "_" from stm32f7 pinmux groups
  ARM: dts: stm32: remove "@" and "_" from stm32f4 pinmux groups
  ARM: dts: stm32: Adapt STM32MP157C ED1 board to STM32 DT diversity
  ...

Link: https://lore.kernel.org/r/39df1dee-3c9f-cd35-bc55-a71223e07100@st.comSigned-off-by: Olof Johansson <olof@lixom.net>

ARM64: DT: Hisilicon SoCs DT updates for 5.6

- Add remote control map name of the IR device for the hi3798cv200 poplar board
- Correct the PCIe bus range setting for the hi3798cv200

* tag 'hisi-arm64-dt-for-5.6' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hi3798cv200: correct PCIe 'bus-range' setting
  arm64: dts: hi3798cv200-poplar: add linux,rc-map-name for IR

Link: https://lore.kernel.org/r/5E169EDE.8020809@hisilicon.comSigned-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.6, please pull the following:

- Stephan adds support for the HWRNG on 2711 (Raspberry Pi 4) which is
  different than the previous Pi chips

- Florian switches the BCM956265HR board to use the hardware I2C
  controllers for interfacing with the SFPs

* tag 'arm-soc/for-5.6/devicetree' of https://github.com/Broadcom/stblinux:
  ARM: dts: bcm2711: Enable HWRNG support
  ARM: dts: bcm2835: Move rng definition to common location
  ARM: dts: NSP: Use hardware I2C for BCM958625HR

Link: https://lore.kernel.org/r/20200108191114.15987-1-f.fainelli@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Add a fixed regulator and use it as power supply for RBG panel.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add a fixed regulator and use it as power supply for DSI panel.

Fixes: 18c88662 ("ARM: dts: stm32: Add display support on stm32f469-disco")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Change non volatile node name from nvmem to efuse to be compliant
with yaml schema.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Change non volatile node name from nvmem to efuse to be compliant
with yaml schema.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Update of the mlahb node according to to DT bindings using json-schema
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

phy-names is required by usbotg_hs driver to get the phy, otherwise, it
considers that there is no phys property.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch enables USB OTG HS on stm32mp15 dkx in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch enables USB Host (USBH) EHCI controller on stm32mp15 dk boards.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch enables USBPHYC (USB PHY Controller on stm32mp15 DKx boards.
This enables the two usbphyc usb2 ports, which require 3 supplies:
3v3, 1v1 and 1v8.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

The recovery mode pin is currently named 'REC_MODE_L', which is
how the signal is called in the schematics. The Chrome OS ABI
requires the pin to be named 'RECOVERY_SW_L', which is also how
it is called on all other veyron devices. Rename the pin to match
the ABI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200108092908.1.I3afd3535b65460e79f3976e9ebfa392a0dd75e01@changeidSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The PCIe 'bus-range' setting is incorrect and causing the following
message during boot.

pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-0f] (conflicts with (null) [bus 00-0f])

Correct it to get rid of the message.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

The flash write protect pin is currently named 'FW_WP_AP', which is
how the signal is called in the schematics. The Chrome OS ABI
requires the pin to be named 'AP_FLASH_WP_L', which is also how
it is called on all other veyron devices. Rename the pin to match
the ABI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200106135142.1.I3f99ac8399a564c88ff48ae6290cc691b47c16ae@changeidSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Merge tag 'omap-for-v5.6/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Drop more legacy platform data for omaps for v5.6 merge window

We can now probe devices with ti-sysc interconnect driver and dts
data, and can continue dropping the related platform data and custom
ti,hwmods dts property for various devices.

And related to that, we finally can remove the legacy sdma support in
favor of using the dmaengine driver only. I was planning to send the
sdma changes separately, but that would have produced a pile of
pointless merge conflicts, so I decided it's best to resolve it locally.
After all, the sdma series also ends up removing the related platform
data.

Note that this series is based on omap-for-v5.6/ti-sysc-dt-signed branch
as it depends for dts data being in place.

* tag 'omap-for-v5.6/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (56 commits)
  ARM: OMAP2+: Drop legacy platform data for sdma
  ARM: OMAP2+: Drop legacy init for sdma
  dmaengine: ti: omap-dma: Use cpu notifier to block idle for omap2
  dmaengine: ti: omap-dma: Allocate channels directly
  dmaengine: ti: omap-dma: Pass sdma auxdata to driver and use it
  dmaengine: ti: omap-dma: Configure global priority register directly
  ARM: OMAP5: hwmod-data: remove OMAP5 IOMMU hwmod data
  ARM: OMAP4: hwmod-data: remove OMAP4 IOMMU hwmod data
  ARM: OMAP2+: Drop legacy platform data for omap4 fdif
  ARM: OMAP2+: Drop legacy platform data for omap4 slimbus
  ARM: OMAP2+: Drop legacy platform data for omap5 kbd
  ARM: OMAP2+: Drop legacy platform data for omap4 kbd
  ARM: OMAP2+: Drop legacy platform data for dra7 smartreflex
  ARM: OMAP2+: Drop legacy platform data for omap4 smartreflex
  ARM: OMAP2+: Drop legacy platform data for omap4 hsi
  ARM: OMAP2+: Drop legacy platform data for am4 vpfe
  ARM: OMAP2+: Drop legacy platform data for dra7 ocp2scp
  ARM: OMAP2+: Drop legacy platform data for omap5 ocp2scp
  ARM: OMAP2+: Drop legacy platform data for omap4 ocp2scp
  ARM: OMAP2+: Drop legacy platform data for am4 ocp2scp
  ...

Link: https://lore.kernel.org/r/pull-1578420398-290837@atomide.com-4Signed-off-by: Olof Johansson <olof@lixom.net>

Bringing in to resolve soc -> add/add conflicts locally

* omap/soc:
  ARM: OMAP2+: use separate IOMMU pdata to fix DRA7 IPU1 boot
  ARM: OMAP2+: omap-iommu.c conversion to ti-sysc
  ARM: OMAP2+: Add workaround for DRA7 DSP MStandby errata i879
  ARM: OMAP4+: remove pdata quirks for omap4+ iommus
  ARM: OMAP2+: pdata-quirks: add PRM data for reset support
  ARM: OMAP2+: am43xx: Add lcdc clockdomain
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.6/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

dts changes for omaps for ti-sysc driver for v5.6 merge window

Devicetree changes for omaps to configure more devices to probe with
ti-sysc interconnect target module:

- Configure am4 qspi

- Configure aes, des and sham accelerators for am3, 4 and dra7

- Configure iommus for omap4, 5 and dra7

- Add a generic compatible for sdma, and configure omap2 and 3 sdma

* tag 'omap-for-v5.6/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (24 commits)
  ARM: dts: omap5: convert IOMMUs to use ti-sysc
  ARM: dts: omap4: convert IOMMUs to use ti-sysc
  ARM: dts: dra74x: convert IOMMUs to use ti-sysc
  ARM: dts: dra7: convert IOMMUs to use ti-sysc
  ARM: dts: Configure interconnect target module for dra7 des
  ARM: dts: Configure interconnect target module for am4 des
  ARM: dts: Configure interconnect target module for dra7 aes
  ARM: dts: Configure interconnect target module for am4 aes
  ARM: dts: Configure interconnect target module for am3 aes
  ARM: dts: Configure interconnect target module for dra7 sham
  ARM: dts: Configure interconnect target module for am4 sham
  ARM: dts: Configure interconnect target module for am3 sham
  ARM: dts: Configure interconnect target module for am4 qspi
  ARM: dts: Configure interconnect target module for omap3 sdma
  ARM: dts: Configure interconnect target module for omap2 sdma
  ARM: dts: Add generic compatible for omap sdma instances
  bus: ti-sysc: Fix iterating over clocks
  ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap
  bus: ti-sysc: Fix missing reset delay handling
  ARM: dts: am437x-gp/epos-evm: fix panel compatible
  ...

Link: https://lore.kernel.org/r/pull-1578420398-290837@atomide.com-3Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.6/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Devicetree changes for omaps for v5.6 merge window

Devicetree changes for omaps for v5.6 to configure more
devices and update boards to use generic lcd panels:

- Configure HDMI for dra76-evm and am57xx-idk

- Correct node name for am3517 mdio

- Convert am335x-evm, am335x-evmsk, and am335x-icev2 to use generic
  panels

* tag 'omap-for-v5.6/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
  ARM: dts: am335x-evmsk: Use drm simple-panel instead of tilcdc-panel
  ARM: dts: am335x-evm: Use drm simple-panel instead of tilcdc-panel
  ARM: dts: omap3: name mdio node properly
  ARM: dts: am57xx-idk-common: add HDMI to the common dtsi
  ARM: dts: dra76-evm: add HDMI output

Link: https://lore.kernel.org/r/pull-1578420398-290837@atomide.com-2Signed-off-by: Olof Johansson <olof@lixom.net>

This enables hardware random number generator support for the BCM2711
on the Raspberry Pi 4 board.
Signed-off-by: Stephen Brennan <stephen@brennan.io>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
[nsaenzjulienne@suse.de: remove unnecessary status="okay"]
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>

BCM2711 inherits from BCM283X, but has an incompatible HWRNG. Move this
node to bcm2835-common.dtsi, so that BCM2711 can define its own.
Signed-off-by: Stephen Brennan <stephen@brennan.io>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>

* mmp/hsic:
  ARM: dts: mmp3: Fix typos

Fixes build failures due to syntax errors.

Fixes: 3240d5b8 ("ARM: dts: mmp3: Add HSIC controllers")
Signed-off-by: Olof Johansson <olof@lixom.net>

* mmp/hsic:
  ARM: dts: mmp3-dell-ariel: Enable the HSIC
  ARM: dts: mmp3: Add HSIC controllers
  dt-bindings: phy: Add binding for marvell,mmp3-hsic-phy
  clk: mmp2: Add HSIC clocks
  dt-bindings: marvell,mmp2: Add clock ids for the HSIC clocks
  + Linux 5.5-rc2

There's a SMSC USB2640 (USB hub & SD controller) connected to it, but
the SD card slot footprint is unpopulated. Also connected to the hub is
a SMSC LAN7500 gigabit ethernet adapter.

Link: https://lore.kernel.org/r/20191220065314.237624-6-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>

There are two on MMP3, along with the PHYs. The PHYs are made compatible
with the NOP transceiver, since there's no driver for the time being and
they're likely configured by the firmware.

Link: https://lore.kernel.org/r/20191220065314.237624-5-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This is the PHY chip for USB HSIC on MMP3 platform.

Link: https://lore.kernel.org/r/20191220065314.237624-4-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>

There are two USB HSIC controllers on MMP2 and MMP3.

Link: https://lore.kernel.org/r/20191220065314.237624-3-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

There are two USB HSIC controllers on MMP2 and MMP3.

Link: https://lore.kernel.org/r/20191220065314.237624-2-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt-bindings-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas DT binding updates for v5.6

  - Document TMU and CAN(FD) support for R-Car RZ/G2N.

* tag 'renesas-dt-bindings-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  dt-bindings: can: rcar_canfd: document r8a774b1 support
  dt-bindings: can: rcar_can: document r8a774b1 support
  dt-bindings: timer: renesas: tmu: Document r8a774b1 bindings

Link: https://lore.kernel.org/r/20200106104857.8361-6-geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm64-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM64 DT updates for v5.6

  - Remove now unused ARCH_R8A7796 config symbol,
  - Rename R-Car H3 and M3-W SoC, and ULCB board DTS files to increase
    naming consistency,
  - Miscellaneous fixes for issues detected by "make dtbs_check",
  - Enhance support for R-Car M3-W+,
  - Display support for the EK874 board,
  - Prepare for split of R-Car H3 ES1.x and ES2.0+ config symbols,
  - Minor fixes and improvements.

* tag 'renesas-arm64-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  arm64: dts: renesas: Prepare for split of ARCH_R8A7795 into ARCH_R8A7795[01]
  arm64: dts: renesas: Sort DTBs in Makefile
  arm64: dts: renesas: Drop redundant SoC prefixes from ULCB DTS file names
  arm64: dts: renesas: Rename r8a7795{-es1,}* to r8a7795[01]*
  arm64: dts: renesas: Add EK874 board with idk-2121wr display support
  arm64: dts: renesas: r8a77961: Add SDHI nodes
  arm64: dts: renesas: r8a77961: Add I2C nodes
  arm64: dts: renesas: r8a77961: Add SYS-DMAC nodes
  arm64: dts: renesas: r8a77961: Add RAVB node
  arm64: dts: renesas: r8a77961: Add GPIO nodes
  arm64: dts: renesas: r8a77961: Add RWDT node
  arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound
  arm64: dts: renesas: r8a77970: Group tuples in thermal reg property
  arm64: dts: renesas: Group tuples in pci ranges and dma-ranges properties
  arm64: dts: renesas: Group tuples in interrupt properties
  arm64: dts: renesas: Group tuples in regulator-gpio states properties
  arm64: dts: renesas: Rename r8a7796* to r8a77960*
  arm64: dts: renesas: Remove use of ARCH_R8A7796

Link: https://lore.kernel.org/r/20200106104857.8361-4-geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.6

  - Touch screen support for the iwg20d board,
  - ARM global timer support on Cortex-A9 MPCore SoCs,
  - Miscellaneous fixes for issues detected by "make dtbs_check".

* tag 'renesas-arm-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  ARM: dts: sh73a0: Add missing clock-frequency for fixed clocks
  ARM: dts: r8a7778: Add missing clock-frequency for fixed clocks
  ARM: dts: rcar-gen2: Add missing mmio-sram bus properties
  ARM: dts: rcar-gen2: Fix PCI high address in interrupt-map-mask
  ARM: dts: renesas: Group tuples in pci ranges and dma-ranges properties
  ARM: dts: renesas: Group tuples in interrupt properties
  ARM: dts: renesas: Group tuples in regulator-gpio states properties
  ARM: dts: r8a7779: Add device node for ARM global timer
  ARM: dts: sh73a0: Add device node for ARM global timer
  ARM: dts: sh73a0: Rename twd clock to periph clock
  ARM: dts: iwg20d-q7-common: Add LCD support

Link: https://lore.kernel.org/r/20200106104857.8361-3-geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'ux500-armsoc-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt

Support the Samsung GT-I8190/Golden phone:

- Proper include file for the AB8505 PMIC variant.
- Add a DTS file for the GT-I8190/Golden
- Extend the IMU, touch screen, WiFi and Bluetooth
  as separate patches.

* tag 'ux500-armsoc-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: dts: ux500: samsung-golden: Add Bluetooth
  ARM: dts: ux500: samsung-golden: Add WiFi
  ARM: dts: ux500: samsung-golden: Add touch screen
  ARM: dts: ux500: samsung-golden: Add IMU (accelerometer + gyroscope)
  ARM: dts: ux500: Add device tree for Samsung Galaxy S III mini (GT-I8190)
  dt-bindings: arm: ux500: Document samsung,golden compatible
  ARM: dts: ux500: Add device tree include for AB8505
  ARM: dts: ux500: Remove unused ste-href-ab8505.dtsi

Link: https://lore.kernel.org/r/CACRpkdaN2Lv_rBEYNiyAarA81yea6Eky8w_htqZqdRng8S-DcA@mail.gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Add basic DT to support Unisoc's SC9863A, with this patch,
the board sp9863a-1h10 can run into console.

Link: https://lore.kernel.org/r/20191223092948.24824-4-zhang.lyra@gmail.comSigned-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Olof Johansson <olof@lixom.net>