Some controllers actually check the first byte of the response (most
don't).  This byte contains the command opcode for R1/R1b and all 1:s
for other types. The difference must be indicated to the controller
so it knows which reply to expect.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Patch from Ben Dooks

Properly tabulate the clock table in arch/arm/mach-s3c2410/clock.c
and put the requisite commas on the end of the structs.

Fix the comment about clock enable and disable in the setup code
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some hosts need to know that a transfer will be multi-block.
Add a data flag to indicate multiple data block transfers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Another reason to use:

	ret = foo();
	if (ret < 0)
		goto out;
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

sg_page_malloc should clear the data buffer, not that extent of mem_map.

This fixes Jesper's sg_page_free "Bad page states"
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Get_dvb_firmware script updated accordingly:
- my $url = "http://www.linuxtv.org/~mkrufky/dvb-usb-bluebird-01.fw";
+ my $url = "http://www.linuxtv.org/download/dvb/firmware/dvb-usb-blue$Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Clean up a recently introduced spaces vs tabs whitespace problem.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- replace omitted 'TODO:'
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Move the code that patches bluebird firmware before upload from the
generic code into the cxusb driver itself.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Add VIDIOC_LOG_STATUS to the radio device ioctl list.
- Reduce the confusion between modes and standards
- Fix stereo reporting for radio.
- Don't set i2c configuration if the chip doesn't support it.
- Fix reporting of current standard for radio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Implemented v4l2 api for sliced vbi data output
to pass WSS data from userspace to the av7110
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Check capabilities for audio settings (volume, balance,
bass, treble, loudness, mute)
- added loudness support
- added missing VIDEO_AUDIO_BALANCE flags for v4l1 compatibility
- do not call msp_any_detect_stereo for non-autoselect chips to
retrieve the current stereo setting: that will temporarily mute
the sound. It is only needed when the stereo mode might be
changed, and for autoselect msp processors that do not periodically
need to update their stereo setting.
- do not wake up the thread if the standard did not change. Prevents
temporary audio drop-out if the standard is set to the same value.
- fix confused stereo detect code where V4L2_TUNER_SUB_STEREO and
V4L2_TUNER_MODE_STEREO values were used incorrectly.
- stereo mode reporting was broken (v4l2 value used to index a
string array expecting v4l1 mode values).
- do not set dsp register 0x30 in the 3410d thread: that register
does not exist for pre-'G' revision msp chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- A new Kconfig option makes the user able to select if the dibusb-mb driver shall claim faulty programmed USB devices which are coming with default Cypress USB IDs.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Some whitespaces cleaned up
- unused code removed
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Indention cleaned for tabsize=8
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Check if in the dvb-usb-device-structure the dvb_pll_desc is set before use.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Indention for values of several request defines were not TabSized=8.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Fixes compiling warning on kernel 2.6.15 with the Intel C compiler. 
- It said drivers/media/dvb/frontends/bcm3510.c(258): 
  warning #592: variable "ret" is used before its value is set
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Replace old norm by the v4l2_std_id values.
- Add code to correctly detect the various capabilities of the
various msp chips. It's not yet used, that's going to be the next step.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- My original settings for this board were incorrect and resulted in
an increased number of signal dropouts.  Replace this with the settings
from the Windows driver.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- codingstyle cleanups & restore some wrongfully deleted dvb-usb-ids
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Add support for the remote control receiver inside the DViCO FusionHDTV
DVB-T Dual Digital, and a keymap for the MCE remote bundled with it.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Support for DVB reception on the PCI half of the DViCO DVB-T Dual Digital.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Add support for the USB portion of the DViCO Dual Digital board.
Patch correct "warm" USB IDs into bluebird firmware before download.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

- Saa7134-core.c saa7134_irq(): Separate GPIO16 and GPIO18 handling. Call
IR-remote-GPIO handler only if the GPIO IRQ is "owned" by it. Added
infrastructure to branch out to a future I2C-IR IRQ handler.
saa7134-core.c saa7134_hwinit2(): Enable only the one GPIO pin and edge to
trigger an IRQ that is wired as keyup/keydown mask. IRQ will only be
generated for an actual key-down event.
saa7134-input.c flyvideo_codes[]: Replace numpad keys with normal ones. Put
meaning to mystery keys. Change some key definitions to have their functions
match their labels better. Fix typos.
saa7134-input.c flydvb_codes[]: Added new table for the larger remote that
comes with the LifeView FlyDVB series.
saa7134-input.c build_key(): In IRQ mode, signal key-down and then key-up
straight in one go.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

Patch from Deepak Saxena

In working on adding 36-bit addressed supersection support to ioremap(),
I came to the conclusion that it would be far simpler to do so by just
splitting __ioremap() into a main external interface and adding an
__ioremap_pfn() function that takes a pfn + offset into the page that
__ioremap() can call. This way existing callers of __ioremap() won't have
to change their code and 36-bit systems will just call __ioremap_pfn()
and we will not have to deal with unsigned long long variables.

Note that __ioremap_pfn() should _NOT_ be called directly by drivers
but is reserved for use by arch_ioremap() implementations that map
32-bit resource regions into the real 36-bit address and then call
this new function.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This is a major update to the cyblafb framebuffer driver. Most
of the stuff has been tested in the mm tree.

Main advantages:
============
  - vxres > xres support
  - ywrap and xpan support
  - much faster for almost all modes (e.g. 1280x1024-16bpp
     draws more than 41 full screens of text instead of about 25
     full screens of text per second on authors Epia 5000)
  - module init/exit code fixed
  - bugs triggered by console rotation fixed
  - lots of minor improvements
  - startup modes suitable for high performance scrolling
     in all directions

This diff  also contains a lot of white space fixes.

No side effects are possible, only one single graphics core is affected.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- i2c names shorten
- removed obsoleted flags on newer modules
- small cleanups
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

Fixed oops after failed netlink socket creation.

Wrong parathenses in if() statement caused err to be 1,
instead of negative value.

Trivial fix, not trivial to find though.
Signed-Off-By: Dmitry Mishin <dim@sw.ru>
Signed-Off-By: Kirill Korotaev <dev@openvz.org>
Signed-Off-By: Linus Torvalds <torvalds@osdl.org>

__rcu_pending() is rather fat and called twice from rcu_pending().

rcu_pending() has multiple callers, and not that small too.

This patch uninlines both of them.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Replaces old debug msgs from bt832, tda743d and tda9875 to newer ones
  as defined under v4l2-common.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>