Merge tag 'qcom-dts-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm ARM dts updates for v5.8

This adds SCM firmware node for IPQ806x and fixes the high resolution
timer for IPQ4019. Samsung Galaxy S5 gains regulators, eMMC and USB
support.

* tag 'qcom-dts-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  ARM: dts: qcom: msm8974-klte: Add max77826 pmic node
  ARM: dts: qcom: msm8974-klte: Add USB node
  ARM: dts: qcom: msm8974-klte: Add sdhci1 node
  ARM: dts: qcom: msm8974-klte: Add gpio-keys nodes
  ARM: dts: qcom: msm8974-klte: Remove inherited vreg_boost node
  ARM: dts: qcom: msm8974-klte: Add pma8084 regulator nodes
  ARM: dts: qcom: ipq4019: fix high resolution timer
  ARM: dts: qcom: add scm definition to ipq806x

Link: https://lore.kernel.org/r/20200519052538.1250076-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm ARM64 DT updates for v5.8

For SDM845 this defines the IPA network accelerator and the CCI camera
control bus, it defines the required UFS reset and adds WiFi for the
Lenovo Yoga C630 and defines GPIO pin names and adds OV8856 and OC7251
camera nodes for DB845c.

For SC7180 it adds GPU support, defines the modem remoteproc, adds the
IPA network accelerator, Coresight and ETM support, adds cpuidle low
power states and updates the CPUs' compatible.

For SM8250 it adds regulators from the PM8150, PM8150L and PM8009 and
adds voltage corners, it defines the nodes for UFS PHY and controller
and finally corrects a typo in the PDC node to make SPMI functional.

For MSM8916 I2C1 and I2C5 are defined, a node for the CCI camera control
interface bus is added and Coresight is disabled by default to match
some product configurations. The Samsung A3U gained display support and
Samsung A5U gained touchscreen support.

MSM8996 now property describes the power supply chain for the GPU, the
CCI camera control interface bus is added and the DB820c has the
regulators of the secondary PMIC defined.

For QCS404 USB PHYs and controllers are defined and wired up for the
EVB.

SDM630/SDM660 platform support is added and the Xiaomi Redmi Note 7
defined.

It also contains a number of changes throughout to improve DT binding
compliance.

* tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (68 commits)
  arm64: dts: qcom: sc7180: Correct the pdc interrupt ranges
  arm64: dts: qcom: sc7180: add IPA information
  arm64: dts: qcom: sc7180: Fix ETMv4 power management patch
  arm64: dts: qcom: sc7180: Add A618 gpu dt blob
  dt-bindings: arm-smmu: Add sc7180 compatible string
  arm64: dts: qcom: msm8996: Make GPU node control GPU_GX GDSC
  arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc
  arm64: dts: qcom: apq8016-sbc: merge -pins.dtsi into main .dtsi
  arm64: dts: qcom: msm8916: move gpu opp table to gpu node
  arm64: dts: qcom: msm8916: avoid using _ in node names
  arm64: dts: qcom: c630: Specify UFS device reset
  arm64: dts: qcom: c630: Add WiFi node
  arm64: dts: qcom: msm8916-samsung-a3u: add nodes for display panel
  arm64: dts: qcom: db820c: Fix invalid pm8994 supplies
  arm64: dts: qcom: db820c: Add pmi8994 RPM regulators
  arm64: dts: qcom: msm8916: Disable coresight by default
  arm64: dts: qcom: sc7180: Add "no-map" to cmd_db reserved area
  arm64: dts: qcom: msm8916-samsung-a5u: Add touchscreen
  arm64: dts: qcom: msm8916-samsung-a2015: Add touchscreen regulator
  arm64: dts: qcom: msm8916: Add blsp_i2c5
  ...

Link: https://lore.kernel.org/r/20200519052528.1249950-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

AT91 DT for 5.8

 - New board: Microchip SAMA5D2 Industrial Connectivity Platform
 - All SoCs are now converted to the new PMC device tree binding
 - sama5d2 flexcom nodes are now fully described in sama5d2.dtsi

* tag 'at91-5.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (35 commits)
  ARM: dts: at91: sama5d2_xplained: Add aliases for the dedicated I2C IPs
  ARM: dts: at91: Configure I2C SCL gpio as open drain
  ARM: dts: at91: sama5d2_xplained: Describe the flx0 I2C function
  ARM: dts: at91: sama5d2_ptc_ek: Add comments to describe the aliases
  ARM: dts: at91: sama5d2_xplained: Add alias for DBGU
  ARM: dts: at91: sama5d2: Add missing flexcom definitions
  ARM: dts: at91: sama5d2: Remove i2s and tcb aliases from SoC dtsi
  ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and I2C flx0 functions
  ARM: dts: at91: sama5d2: Add DMA bindings for the flx1 I2C function
  ARM: dts: at91: sama5d2: Add DMA bindings for the flx3 SPI function
  ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and UART flx4 functions
  ARM: dts: at91: sama5d2: Specify the FIFO size for the Flexcom UART
  ARM: dts: at91: sama5d2: Move flx0 definitions in the SoC dtsi
  ARM: dts: at91: sama5d2: Move flx1 definitions in the SoC dtsi
  ARM: dts: at91: sama5d2: Move flx2 definitions in the SoC dtsi
  ARM: dts: at91: sama5d2: Move flx3 definitions in the SoC dtsi
  ARM: dts: at91: sama5d2: Move flx4 definitions in the SoC dtsi
  ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions
  ARM: dts: at91: sama5d27_wlsom1: Add alias for i2c0
  ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP
  ...

Link: https://lore.kernel.org/r/20200518212844.GA26356@piout.netSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'uniphier-dt64-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt

UniPhier ARM64 SoC DT updates for v5.8

- add DMA controller nodes

- add Akebi96 board support

* tag 'uniphier-dt64-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: Add support for Akebi96
  dt-bindings: arm: Add Akebi96 board support
  arm64: dts: uniphier: add #address-cells and #size-cells to SPI nodes
  arm64: dts: uniphier: Stabilize Ethernet RGMII mode of PXs3 ref board
  arm64: dts: uniphier: Add ethernet aliases
  arm64: dts: uniphier: Add XDMAC node

Link: https://lore.kernel.org/r/CAK7LNARUL52pBhg8AD9XeScVqhD8qr2eVEfu4+1v8D+KPyOwNw@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'uniphier-dt-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt

UniPhier ARM SoC DT updates for v5.8

- add DMA controller nodes

* tag 'uniphier-dt-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add #address-cells and #size-cells to SPI nodes
  ARM: dts: uniphier: Add ethernet aliases
  ARM: dts: uniphier: Add XDMAC node

Link: https://lore.kernel.org/r/CAK7LNAQXSpg4s0e0d-tp9j85Sj01t13zAa5+rqsOWu4ZvkpYhg@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'v5.7-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt

MT2712:
- replace deprecated compatible for the usb PHY

MT6797:
- switch to SPDX identifier
- add and enable I2C device for x20 development board
- add I2C compatible to the binding description

MT7622:
- add Wi-Fi device and enable it for the Bananpi-R64

MT8173:
- add CPU capacities based on Dhryston benchmark
- fix DT build warnings
- set throtteling range to limitless
- add Elm and Hana devices on which several chromebooks are based
- add Global Command Queue entries to the users

MT8183:
- split cpuidle states in two as the clusters have different target residencies

* tag 'v5.7-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm64: dts: mt8173: Add capacity-dmips-mhz attributes
  arm64: dts: mt2712: use non-empty ranges for usb-phy
  arm64: dts: mt8173: fix mdp aliases property name
  arm64: dts: mediatek: Switch to SPDX license identifier for MT6797 SoC
  arm64: dts: mediatek: Enable I2C support for 96Boards X20 Development board
  arm64: dts: mediatek: Add I2C support for MT6797 SoC
  dt-bindings: i2c: Document I2C controller binding for MT6797 SoC
  arm64: dts: mt8173: fix cooling device range
  arm64: dts: mediatek: add mt8173 elm and hana board
  arm64: dts: mt8173: fix unit name warnings
  arm64: dts: mt8173: add uart aliases
  dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
  arm64: dts: mt8183: adjust cpuidle target residency
  arm64: dts: mt8173: Add gce setting in mmsys and display node
  arm64: dts: mt7622: add built-in Wi-Fi device nodes

Link: https://lore.kernel.org/r/2794a8db-c14f-ac34-9e28-9f3700db6c4c@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ux500-dts-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt

Ux500 DTS updates for the v5.8 kernel series:

- Add proximity sensor and magnetometer to the Samsung Golden
  devicetree.
- Add magnetometer and touchscreen to the Samsung Skomer
  devicetree.

* tag 'ux500-dts-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: dts: ux500: Add touchscreen to the Skomer
  ARM: dts: ux500: samsung-skomer: Add magnetometer
  ARM: dts: ux500: samsung-golden: Add magnetometer
  ARM: dts: ux500: samsung-golden: Add proximity sensor

Link: https://lore.kernel.org/r/CACRpkdbukO33SxAZ_yn-1N8=hq3hF5OBOtP_V0fbjRT-fAa87A@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'v5.7-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt

MT2701:
- add MUSB device to the SoC and the EVB

MT7623:
- add Mali-450 device node and bindings
- add phy to gmac2

* tag 'v5.7-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm: dts: mt2701: Add usb2 device nodes
  dt-bindings: gpu: mali-utgard: add mediatek, mt7623-mali compatible
  arm: dts: mt7623: add Mali-450 device node
  arm: dts: mt7623: add phy-mode property for gmac2

Link: https://lore.kernel.org/r/ec17cf62-5463-9537-6618-2db9b2b5036e@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'socfpga_dts_update_for_v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt

SoCFPGA DTS updates for v5.8
- Leave the FPGA bridges disabled in base dtsi
- Add fpga2hps and fpga2sdram bridges on base Cyclone5/Arria5 dtsi

* tag 'socfpga_dts_update_for_v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: dts: socfpga: Add fpga2hps and fpga2sdram bridges
  ARM: dts: socfgpa: set bridges status to disabled

Link: https://lore.kernel.org/r/20200515193029.11318-2-dinguyen@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Our usual number of patches to improve the Allwinner Device Tree
support, including:
  - Support for the IOMMU on the H6
  - Support for cpufreq / thermal throttling on the H6
  - Support for the mailbox on the A64, A83t, H3, H5 and H6
  - New boards: A20-OLinuXino-LIME-eMMC

* tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (23 commits)
  arm64: dts: allwinner: h6: Add IOMMU
  arm64: dts: allwinner: h6: Enable CPU opp tables for Tanix TX6
  arm64: dts: allwinner: h6: add voltage range to OPP table
  arm64: dts: allwinner: sun50i-a64: Add missing address/size-cells
  arm64: dts: allwinner: h6: Enable CPU opp tables for Pine H64
  arm64: dts: allwinner: Sort Pine H64 device-tree nodes
  arm64: dts: allwinner: h6: Enable CPU opp tables for Orange Pi 3
  arm64: dts: allwinner: h6: Enable CPU opp tables for Beelink GS1
  arm64: dts: allwinner: h6: Add CPU Operating Performance Points table
  arm64: dts: allwinner: h6: Add thermal trip points/cooling map
  arm64: dts: allwinner: h6: Add clock to CPU cores
  arm64: allwinner: h6: orangepi-lite2: Support BT+WIFI combo module
  arm64: dts: allwinner: h6: orangepi: Disable OTG mode
  arm64: dts: allwinner: h6: orangepi: Add gpio power supply
  ARM: dts: sun8i-h2-plus-bananapi-m2-zero: Fix led polarity
  arm64: dts: allwinner: h6: Add msgbox node
  arm64: dts: allwinner: a64: Add msgbox node
  ARM: dts: sunxi: h3/h5: Add msgbox node
  ARM: dts: sunxi: a83t: Add msgbox node
  ARM: dts: sun8i-h3: add opp table for mali gpu
  ...

Link: https://lore.kernel.org/r/cfa66bd9-f74c-4614-9ea5-9ef8546cc571.lettre@localhostSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-5.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

ARM: tegra: Device tree changes for v5.8-rc1

This contains a bit of cleanup and CPU frequency scaling support for the
Tegra30 Beaver board.

* tag 'tegra-for-5.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: dts: tegra30: beaver: Add CPU Operating Performance Points
  ARM: dts: tegra30: beaver: Set up voltage regulators for DVFS
  ARM: tegra: Kill off "simple-panel" compatibles

Link: https://lore.kernel.org/r/20200515145311.1580134-11-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-5.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

dt-bindings: Changes for v5.8-rc1

This adds bindings for the CSI TPG clock on Tegra210, moves various
clocks from the clock and reset controller to the PMC where their
controls really are, adds bindings for the external memory controller
and video capture controller on Tegra210, as well as CPU frequency
scaling on Tegra20 and Tegra30.

* tag 'tegra-for-5.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: i2c: tegra: Document Tegra210 VI I2C
  dt-bindings: tegra: Add VI and CSI bindings
  dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30
  dt-bindings: memory: tegra: Add external memory controller binding for Tegra210
  dt-bindings: clock: tegra: Remove PMC clock IDs
  dt-bindings: clock: tegra: Add clock ID for CSI TPG clock

Link: https://lore.kernel.org/r/20200515145311.1580134-4-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ti-k3-dt-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt

Texas Instruments K3 SoC DT updates for v5.8

- Add DSS support for both AM65x and J721e
- Add watchdog support for J721e
- Add EHRPWM support for AM65x
- Add Thermal support for AM65x

* tag 'ti-k3-dt-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
  arm64: dts: ti: k3-j721e-main: Add main domain watchdog entries
  arm64: dts: ti: k3-am65-main: Add ehrpwm nodes
  arm64: dts: ti: am654: Add thermal zones
  arm64: dts: ti: am65-wakeup: Add VTM node
  arm64: dts: ti: k3-j721e-common-proc-board: add assigned clks for DSS
  arm64: dts: ti: k3-j721e-main: Add DSS node
  arm64: dts: ti: am654: Add DSS node

Link: https://lore.kernel.org/r/7484d3c9-323f-36a3-f0df-1287586f356d@ti.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt-bindings-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas DT binding updates for v5.8 (take two)

  - Document support for the RZ/G1H-based iWave RainboW Qseven SOM
    (G21M) and board (G21D).

* tag 'renesas-dt-bindings-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  dt-bindings: arm: renesas: Document iW-RainboW-G21D-Qseven-RZG1H board
  dt-bindings: arm: renesas: Document iW-RainboW-G21M-Qseven-RZG1H SoM

Link: https://lore.kernel.org/r/20200515100547.14671-6-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.8 (take two)

  - Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
    Qseven SOM (G21M) and board (G21D),
  - Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
    Silicon Linux EK874 RZ/G2E evaluation kit.

* tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  arm64: dts: renesas: r8a774c0-cat874: Add support for AISTARVISION MIPI Adapter V2.1
  ARM: dts: r8a7742: Add GPIO nodes
  ARM: dts: r8a7742: Add [H]SCIF{A|B} support
  ARM: dts: r8a7742: Add IRQC support
  ARM: dts: r8a7742-iwg21d-q7: Add iWave G21D-Q7 board based on RZ/G1H
  ARM: dts: r8a7742-iwg21m: Add iWave RZ/G1H Qseven SOM
  ARM: dts: r8a7742: Initial SoC device tree
  clk: renesas: Add r8a7742 CPG Core Clock Definitions
  dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros

Link: https://lore.kernel.org/r/20200515100547.14671-3-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.8, round 1

Highlights:
----------

MCU part:
 -fix a typo for DAC io-channel-cells on f429 and h743

MPU part:
 -Generic:
  -Bump tp PSCI 1.0
  -Fix a typo for DAC io-channel-cells
  -Add M4 pdds for deep sleep mode
  -Add I2C fatmode plus support

 -Add new Octavio lxa-mc1 board based on OSDMP15x SiP

 -Add new Stinger96 board support. It is a 96Boards IoT Extended board
  based on stm32mp157a SoC. Some figures: 256MB DDR, 125MB and flash,
  Onboard BG96 modem...

 -Add IoT Box board support based on stinger96 board + Wifi/BT, CCS811
  VOC sensor, 2 digitals microphones ...

 -DH:
  -Adapt dhcom-som and dhcom-pdk2 dts(i) files to STM32MP15 SoC diversity
  -Add GPIO led and GPIO keys support on PDK2 board

 -AV96:
  -Major rework to support official avenger96 board based on DHCOR SOM.
  -Prototype board is no more supported

* tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (58 commits)
  ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
  ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2
  ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2
  ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
  ARM: dts: stm32: Add IoT Box board support
  dt-bindings: arm: stm32: Document IoT Box compatible
  ARM: dts: stm32: Add Stinger96 board support
  dt-bindings: arm: stm32: Document Stinger96 compatible
  ARM: dts: stm32: Add missing pinctrl entries for STM32MP15
  dt-bindings: Add vendor prefix for Shiratech Solutions
  ARM: dts: stm32: Add bindings for SPI2 on AV96
  ARM: dts: stm32: Add alternate pinmux for SPI2 pins
  ARM: dts: stm32: Add bindings for ADC on AV96
  ARM: dts: stm32: Add alternate pinmux for ADC pins
  ARM: dts: stm32: Add bindings for FDCAN2 on AV96
  ARM: dts: stm32: Add alternate pinmux for FDCAN2 pins
  ARM: dts: stm32: Add bindings for FDCAN1 on AV96
  ARM: dts: stm32: Add alternate pinmux for FDCAN1 pins
  ARM: dts: stm32: Repair I2C2 operation on AV96
  ARM: dts: stm32: Add alternate pinmux for I2C2 pins
  ...

Link: https://lore.kernel.org/r/19160355-364d-170c-7ae2-5ba7f714103f@st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Samsung DTS ARM changes for v5.8

1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
   mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
   (e.g. Samsung Galaxy S): necessary configuration for suspend, audio
   support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).

* tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
  ARM: dts: s5pv210: Set MAX8998 GPIO pulls on Aries boards
  ARM: dts: s5pv210: Correct FIMC definitions
  ARM: dts: s5pv210: Assign clocks to MMC devices on Aries boards
  ARM: dts: s5pv210: Enable ADC on Aries boards
  ARM: dts: s5pv210: Add an ADC node
  ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards
  ARM: dts: s5pv210: Add si470x FM radio to Galaxy S
  ARM: dts: s5pv210: Add remaining i2c-gpio adapters to Aries boards
  ARM: dts: s5pv210: Add panel support to Aries boards
  ARM: dts: s5pv210: Add touchkey support to Aries boards
  ARM: dts: s5pv210: Add FSA9480 support to Aries boards
  ARM: dts: s5pv210: Add WM8994 support to Aries boards
  ARM: dts: s5pv210: Disable pulls on GPIO I2C adapters for Aries
  ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on Aries
  ARM: dts: s5pv210: Correct gpi pinctrl node name
  ARM: dts: s5pv210: Add sleep GPIO configuration for Galaxy S
  ARM: dts: s5pv210: Add sleep GPIO configuration for Fascinate4G
  ARM: dts: s5pv210: Add helper define for sleep gpio config
  ARM: dts: exynos: Enable WLAN support for the UniversalC210 board
  ARM: dts: exynos: Enable WLAN support for the Rinato board
  ...

Link: https://lore.kernel.org/r/20200512122922.5700-2-krzk@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

This pull request contains Broadcom ARM-based SoCs Device Tree changes
for v5.8, please pull the following:

- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
  controlling power to the SD card, adds support for the vmmc regulator
  for the emmc2 controller and finally updates the power management
  provider for V3D to use the firmware to solve instabilities.

* tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux:
  ARM: dts: bcm283x: Use firmware PM driver for V3D
  ARM: dts: bcm2711: Add vmmc regulator in emmc2
  ARM: dts: bcm2711: Update expgpio's GPIO labels

Link: https://lore.kernel.org/r/20200511210522.28243-2-f.fainelli@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

ARM64: DT: Hisilicon SoCs DT updates for 5.8

- Add pinconf for spi2 and spi3 nodes and increase the drive
  strength to achieve the max speed for the Hikey960 board
- Add CTI nodes for the Hikey620 board

* tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hi6220: Add CTI options
  arm64: dts: hikey960: pinctrl: Fix spi2/spi3 pinconf

Link: https://lore.kernel.org/r/5EBE430E.6090508@hisilicon.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'realtek-dt-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek into arm/dt

Realtek Arm based SoC DT for v5.8

Add RTD1195, RTD1395 and RTD1619 SoCs as well as Xnano X5 TV box.
Clean up memory nodes and /soc ranges. Factor out r-bus and partition it
into CRT, Iso, Misc, SB2 and SCPU Wrapper blocks.

* tag 'realtek-dt-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek: (35 commits)
  dt-bindings: reset: rtd1295: Add SB2 reset
  arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes
  arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes
  arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes
  ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes
  arm64: dts: realtek: rtd16xx: Add CRT syscon node
  ARM: dts: rtd1195: Add UART resets
  ARM: dts: rtd1195: Add reset nodes
  dt-bindings: reset: Add Realtek RTD1195
  ARM: dts: rtd1195: Add CRT syscon node
  arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon
  arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon
  arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon
  ARM: dts: rtd1195: Introduce iso and misc syscon
  arm64: dts: realtek: rtd1295: Add Xnano X5
  dt-bindings: arm: realtek: Add Xnano X5
  dt-bindings: vendor-prefixes: Add Xnano
  arm64: dts: realtek: rtd16xx: Add memory reservations
  arm64: dts: realtek: rtd16xx: Carve out boot ROM from memory
  arm64: dts: realtek: Add RTD1619 SoC and Realtek Mjolnir EVB
  ...

Link: https://lore.kernel.org/r/20200510232158.18477-2-afaerber@suse.deSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'aspeed-5.8-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt

ASPEED device tree updates for 5.8

New machines:

 - YADRO's ast2500 OpenPower P9 Nicole BMC
 - Facebook's ast2500 x86 Yosemite V2 BMC

The AST2600 machines Rainier and Tacoma were fleshed out.

Machines have started describing the GPIO names as userspace attempts
to use the GPIO chardev API.

* tag 'aspeed-5.8-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed: (32 commits)
  ARM: dts: aspeed: Change KCS nodes to v2 binding
  ARM: dts: Aspeed: AST2600: Add XDMA PCI-E root control reset
  ARM: dts: aspeed: ast2600: Add XDMA Engine
  ARM: dts: aspeed: ast2500: Add XDMA Engine
  ARM: dts: aspeed: Adding Facebook Yosemite V2 BMC
  ARM: dts: aspeed: Add YADRO Nicole BMC
  ARM: dts: aspeed: mihawk: add aliases for i2c
  ARM: dts: aspeed: tacoma: Add TPM
  ARM: dts: aspeed: tacoma: Enable the second VUART
  ARM: dts: aspeed: tacoma: Add iio-hwmon nodes for IIO devices
  ARM: dts: aspeed: rainier: Add VGA reserved memory region
  ARM: dts: aspeed: rainier: Add gpio line names
  ARM: dts: aspeed: tacoma: Add gpio line names
  ARM: dts: aspeed: zaius: Add gpio line names
  ARM: dts: aspeed: romulus: Add gpio line names
  ARM: dts: aspeed: witherspoon: Add gpio line names
  ARM: dts: aspeed: ast2600: Set arch timer always-on
  ARM: dts: aspeed: tacoma: Add GPIOs for FSI
  ARM: dts: aspeed: mihawk: Change the name of leds
  ARM: dts: aspeed: rainier: Remove regulators
  ...

Link: https://lore.kernel.org/r/CACPK8Xd-=XFREvvS-mK_ECyn14y0GPAMyy5BpEEUYfaw4jAgsw@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

DTS changes for omaps for v5.8 merge window

We add support for beaglebone-ai board that's am5729 based devices.

Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.

Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.

Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.

* tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
  ARM: OMAP5: Make L4SEC clock domain SWSUP only
  ARM: OMAP4: Make L4SEC clock domain SWSUP only
  ARM: dts: omap5: add DES crypto accelerator node
  ARM: dts: omap5: add SHA crypto accelerator node
  ARM: dts: omap5: add aes2 entry
  ARM: dts: omap5: add aes1 entry
  ARM: dts: dra7-ipu-dsp-common: Add watchdog timers to IPU and DSP nodes
  ARM: dts: am571x-idk: Add CMA pools and enable IPUs & DSP1 rprocs
  ARM: dts: am572x-idk-common: Add CMA pools and enable IPU & DSP rprocs
  ARM: dts: beagle-x15-common: Add CMA pools and enable IPU & DSP rprocs
  ARM: dts: dra76-evm: Add CMA pools and enable IPU & DSP rprocs
  ARM: dts: dra71-evm: Add CMA pools and enable IPUs & DSP1 rprocs
  ARM: dts: dra72-evm-revc: Add CMA pools and enable IPUs & DSP1 rprocs
  ARM: dts: dra72-evm: Add CMA pools and enable IPUs & DSP1 rprocs
  ARM: dts: dra7-evm: Add CMA pools and enable IPU & DSP rprocs
  ARM: dts: dra7-ipu-dsp-common: Add timers to IPU and DSP nodes
  ARM: dts: dra7-ipu-dsp-common: Add mailboxes to IPU and DSP nodes
  ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files
  ARM: dts: DRA72x: Add aliases for rproc nodes
  ARM: dts: DRA74x: Add aliases for rproc nodes
  ...

Link: https://lore.kernel.org/r/pull-1588873628-477615@atomide.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt-bindings-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas DT binding updates for v5.8

  - Document System Controller (SYSC) and Reset (RST) support for
    RZ/G1H.

* tag 'renesas-dt-bindings-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  dt-bindings: reset: rcar-rst: Document r8a7742 reset module
  dt-bindings: power: rcar-sysc: Document r8a7742 SYSC binding

Link: https://lore.kernel.org/r/20200430084849.1457-6-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-arm-dt-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt

Renesas ARM DT updates for v5.8

  - USB, UART, PWM, and PCIe support for R-Car M3-W+,
  - PWM (16-bit Timer Pulse Unit and PWM Timers) support for R-Car M2-W,
  - Minor fixes and cleanups.

* tag 'renesas-arm-dt-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  arm64: dts: renesas: Fix IOMMU device node names
  ARM: dts: renesas: Fix IOMMU device node names
  ARM: dts: shmobile: Update CMT1 compatible values
  ARM: dts: r8a7791: Add PWM device nodes
  ARM: dts: r8a7791: Add TPU device node
  arm64: dts: renesas: r8a77961: Add PCIe device nodes
  arm64: dts: renesas: r8a77961: Add PWM device nodes
  arm64: dts: renesas: r8a77961: Add SCIF and HSCIF nodes
  arm64: dts: renesas: r8a77961: Add USB3.0 device nodes
  arm64: dts: renesas: r8a77961: Add USB2.0 device nodes

Link: https://lore.kernel.org/r/20200430084849.1457-3-geert+renesas@glider.beSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt

Versatile DTS updates for the v5.8 kernel:

Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.

If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.

* tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: dts: Add devicetree for Integrator/AP with IM-PD1

Link: https://lore.kernel.org/r/CACRpkdZ-28o+pPdP7i_fc+7g4ndPWf+SWTsjnhFEegTggiXVSg@mail.gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sti-dt-for-v5.8-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into arm/dt

STi DT fixes:
- Remove duplicated rng node in stih407-family.dtsi
- Fix complain about IRQ_TYPE_NONE usage in stih418.dtsi

* tag 'sti-dt-for-v5.8-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
  dts: arm: stih407-family: remove duplicated rng nodes
  dts: arm: stih418: Fix complain about IRQ_TYPE_NONE usage

Link: https://lore.kernel.org/r/4b0c02e7-a247-50c0-d729-88d16b9dd7fd@st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add emmc and sd card devicetree nodes for SC9863A.

Link: https://lore.kernel.org/r/20200414101636.24503-3-zhang.lyra@gmail.comSigned-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

add clock devicetree nodes for SC9863A.

Link: https://lore.kernel.org/r/20200414101636.24503-2-zhang.lyra@gmail.comSigned-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Few PDC interrupts do not map to respective parent GIC interrupt.
Fix this by correcting the pdc interrupt map.

Fixes: 22f185ee ("arm64: dts: qcom: sc7180: Add pdc interrupt controller")
Cc: devicetree@vger.kernel.org
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1589804402-27130-1-git-send-email-mkshah@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add IPA-related nodes and definitions to "sc7180.dtsi".
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200518214939.9730-1-elder@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The lack of unique context in  '0f1decaa ("arm64: dts: qcom: sc7180:
Support ETMv4 power management")' caused the patch to be applied
off-by-one. Move the "arm,coresight-loses-context-with-cpu" properties
down one node, so that it applies to the ETMs and not the replicator.
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The sama5d2 SoC has two dedicated I2C IPs that are enabled on
sama5d2_xplained. Add alias for the i2c devices to not rely on
probe order for the i2c device numbering.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200518114802.253660-1-tudor.ambarus@microchip.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

This adds touchscreen support to the Ux500 Samsung
GT-S7710 "Skomer" mobile phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200516212913.485365-1-linus.walleij@linaro.org

Add musb nodes and usb2 phy nodes for MT2701
Signed-off-by: Min Guo <min.guo@mediatek.com>
Link: https://lore.kernel.org/r/20191211015446.11477-3-min.guo@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The MediaTek MT7623 SoC contains a Mali-450, so add a compatible for it
and define its own vendor-specific properties.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/efeadefe3895bcadf1d2e9847b82206dd8c7ec35.1563867856.git.ryder.lee@mediatek.com
[mb: move to yaml file]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add a node for Mali-450.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/af7b5a2e00eb3a4b6262807c378e43afd5f74779.1563867856.git.ryder.lee@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Dhrystone benchmark on Acer Chromebook R13 CB5-312T:
A72: 15698587 dps @ 1807 MHz
A53:  7598784 dps @ 1703 MHz
Signed-off-by: Ulrich Hecht <uli-qwV78thtvt0@public.gmane.org>
Link: https://lore.kernel.org/r/1563529816-3992-1-git-send-email-uli@fpond.euSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Use non-empty ranges for usb-phy to make the layout of
its registers clearer;
Replace deprecated compatible by generic
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Fix warning:
Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20200414030815.192104-1-hsinyi@chromium.orgSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Switch to SPDX license identifier for MT6797 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-5-manivannan.sadhasivam@linaro.orgSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>