There is no code protecting i2c_dev to be freed after it is returned
from i2c_dev_get_by_minor() and using it to access the value which we
already have (minor) isn't safe really.

Avoid using it and get the adapter directly from 'minor'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There are more than 7 busses, but only 7 are user visible. Update comment
accordingly.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The i801 chip can handle the Host Notify feature since ICH 3 as mentioned
in http://www.intel.com/content/dam/doc/datasheet/82801ca-io-controller-hub-3-datasheet.pdf

Enable the functionality unconditionally and propagate the alert
on each notification.

With a T440s and a Synaptics touchpad that implements Host Notify, the
payload data is always 0x0000, so I am not sure if the device actually
sends the payload or if there is a problem regarding the implementation.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

On a CRC error while using hardware-supported PEC, an additional
error bit is set in the auxiliary status register.  If this bit
isn't cleared, all subsequent operations will fail, essentially
hanging the controller.

The fix is simple: check, report, and clear the bit in
i801_check_post().  Also, in case the driver starts with the
hardware in that state, clear it in i801_check_pre() as well.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
[wsa: remove two empty lines while here]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Simply sort header block alphabetically.

While here fix an indentation in one place and update a copyright line for
Intel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch enables I2C controllers found on Intel Edison board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

On some platforms, such as Intel Medfield, the I2C slave devices are enumerated
through SFI tables where bus numbering is expected to be defined in the OS.
Make the bus number allocation robust for such platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I believe i2c-designware-baytrail.c doesn't have strict dependency that
Intel SoC IOSF Sideband support must be always built-in in order to be
able to compile support for Intel Baytrail I2C bus sharing HW semaphore.

Redefine build dependencies so that CONFIG_IOSF_MBI=y is required only
when CONFIG_I2C_DESIGNWARE_PLATFORM is built-in.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: David Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This allows applications to set the transfer timeout in 10ms increments via
ioctl I2C_TIMEOUT.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

qup_i2c_issue_read() derives the address from i2c_msg.
This called in the read path when I2C_M_RD flag is set.
Therefore, use the 8 bit address helper function.
Signed-off-by: Naveen Kaje <nkaje@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Among the bus errors reported from the QUP_MASTER_STATUS register
only NACK is considered and transfer gets suspended, while
other errors are ignored. Correct this and suspend the transfer
for other errors as well. This avoids unnecessary 'timeouts' which
happens when waiting for events that would never happen when there
is already an error condition on the bus. Also the error handling
procedure should be the same for both NACK and other bus errors in
case of dma mode. So correct that as well.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

With CONFIG_DEBUG_SG is enabled and when dma mode is used, below dump is seen,

------------[ cut here ]------------
kernel BUG at include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-00459-g9f087b9-dirty #7
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
task: ffffffc036868000 ti: ffffffc036870000 task.ti: ffffffc036870000
PC is at qup_sg_set_buf.isra.13+0x138/0x154
LR is at qup_sg_set_buf.isra.13+0x50/0x154
pc : [<ffffffc0005a0ed8>] lr : [<ffffffc0005a0df0>] pstate: 60000145
sp : ffffffc0368735c0
x29: ffffffc0368735c0 x28: ffffffc036873752
x27: ffffffc035233018 x26: ffffffc000c4e000
x25: 0000000000000000 x24: 0000000000000004
x23: 0000000000000000 x22: ffffffc035233668
x21: ffffff80004e3000 x20: ffffffc0352e0018
x19: 0000004000000000 x18: 0000000000000028
x17: 0000000000000004 x16: ffffffc0017a39c8
x15: 0000000000001cdf x14: ffffffc0019929d8
x13: ffffffc0352e0018 x12: 0000000000000000
x11: 0000000000000001 x10: 0000000000000001
x9 : ffffffc0012b2d70 x8 : ffffff80004e3000
x7 : 0000000000000018 x6 : 0000000030000000
x5 : ffffffc00199f018 x4 : ffffffc035233018
x3 : 0000000000000004 x2 : 00000000c0000000
x1 : 0000000000000003 x0 : 0000000000000000

Process swapper/0 (pid: 1, stack limit = 0xffffffc036870020)
Stack: (0xffffffc0368735c0 to 0xffffffc036874000)

sg_set_bug expects that the buf parameter passed in should be from
lowmem and a valid pageframe. This is not true for pages from
dma_alloc_coherent which can be carveouts, hence the check fails.
Change allocation of sg buffers from dma_coherent memory to kzalloc
to fix the issue. Note that now dma_map/unmap is used to make the
kzalloc'ed buffers coherent before passing it to the dmaengine.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Implement fast mode plus that allows bus speeds of up to 1MHz.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

- new method to caculate i2c timings for rk3399:
  There was an timing issue about "repeated start" time at the I2C
  controller of version0, controller appears to drop SDA at .875x (7/8)
  programmed clk high. On version 1 of the controller, the rule(.875x)
  isn't enough to meet tSU;STA
  requirements on 100k's Standard-mode. To resolve this issue,
  sda_update_config, start_setup_config and stop_setup_config for I2C
  timing information are added, new rules are designed to calculate
  the timing information at new v1.
- pclk and function clk are separated at rk3399
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[wsa: fixed whitespace issue]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The bus clock and function clock are separated at rk3399,
and others use one clock as the bus clock and function clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The i2c timing specs are really just constant data. There's no reason
to write code to init them, so move them out to structures. This not
only is a cleaner solution but it will reduce code duplication when we
introduce a new variant of rk3x_i2c_calc_divs() in a future patch.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Specifying the i2c SoC data in an array provides very little benefit and
gets unwieldly / confusing as the array grows since the next bit of code
needs to refer to elements in the array by their raw integral index.

Let's just create a single 'static const' structure for each SoC so that
we can refer to these structures by ID.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

rk3x_i2c_setup() gets called directly before rk3x_i2c_start(),
and the last thing in setup was to clean the IPD, so no reason
to do it at the beginning of start.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The "div_high" and "div_low" values are always used together.
Group them into a structure to make it easier to pass them
both around. This structure also provides a place for future
calculated timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add kernel-doc documentation for the elements of the previously
undocumented struct rk3x_i2c.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

SMBus Host Notify allows a slave device to act as a master on a bus to
notify the host of an interrupt. On Intel chipsets, the functionality
is directly implemented in the firmware. We just need to export a
function to call .alert() on the proper device driver.

i2c_handle_smbus_host_notify() behaves like i2c_handle_smbus_alert().
When called, it schedules a task that will be able to sleep to go through
the list of devices attached to the adapter.

The current implementation allows one Host Notification to be scheduled
while an other is running.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

.alert() is meant to be generic, but there is currently no way
for the device driver to know which protocol generated the alert.
Add a parameter in .alert() to help the device driver to understand
what is given in data.

This patch is required to have the support of SMBus Host Notify protocol
through .alert().
Tested-by: Andrew Duggan <aduggan@synaptics.com>
For hwmon:
Acked-by: Guenter Roeck <linux@roeck-us.net>
For IPMI:
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

osif_table is never modified, so declare it as const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

David reported that the length for memset was incorrect (element sizes
were not taken into account). Then I saw that we are clearing kzalloced
memory, so we can simply drop this code.
Reported-by: David Binderman <dcb314@hotmail.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The interrupt handling code makes it look like several status values
may be merged together before being processed, while this will never
happen. Change from bit-wise OR to simple assignment to make it more
obvious and avoid misunderstanding.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some I2C devices have multiple addresses assigned, for example each address
corresponding to a different internal register map page of the device.
So far drivers which need support for this have handled this with a driver
specific and non-generic implementation, e.g. passing the additional address
via platform data.

This patch provides a new helper function called i2c_new_secondary_device()
which is intended to provide a generic way to get the secondary address
as well as instantiate a struct i2c_client for the secondary address.

The function expects a pointer to the primary i2c_client, a name
for the secondary address and an optional default address. The name is used
as a handle to specify which secondary address to get.

The default address is used as a fallback in case no secondary address
was explicitly specified. In case no secondary address and no default
address were specified the function returns NULL.

For now the function only supports look-up of the secondary address
from devicetree, but it can be extended in the future
to for example support board files and/or ACPI.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull thermal management fixes from Zhang Rui:

 - fix an ordering issue in cpu cooling that cooling device is
   registered before it's ready (freq_table being populated).
   (Lukasz Luba)

 - fix a missing comment update (Caesar Wang)

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: add the note for set_trip_temp
  thermal: cpu_cooling: fix improper order during initialization

Pull block layer fixes from Jens Axboe:
 "A small collection of fixes for the current series.  This contains:

   - Two fixes for xen-blkfront, from Bob Liu.

   - A bug fix for NVMe, releasing only the specific resources we
     requested.

   - Fix for a debugfs flags entry for nbd, from Josef.

   - Plug fix from Omar, fixing up a case of code being switched between
     two functions.

   - A missing bio_put() for the new discard callers of
     submit_bio_wait(), fixing a regression causing a leak of the bio.
     From Shaun.

   - Improve dirty limit calculation precision in the writeback code,
     fixing a case where setting a limit lower than 1% of memory would
     end up being zero.  From Tejun"

* 'for-linus' of git://git.kernel.dk/linux-block:
  NVMe: Only release requested regions
  xen-blkfront: fix resume issues after a migration
  xen-blkfront: don't call talk_to_blkback when already connected to blkback
  nbd: pass the nbd pointer for flags debugfs
  block: missing bio_put following submit_bio_wait
  blk-mq: really fix plug list flushing for nomerge queues
  writeback: use higher precision calculation in domain_dirty_limits()

Pull GPIO fixes from Linus Walleij:
 "A new bunch of GPIO fixes for v4.7.

  This time I am very grateful that Ricardo Ribalda Delgado went in and
  fixed my stupid refcounting mistakes in the removal path for GPIO
  chips.  I had a feeling something was wrong here and so it was.  It
  exploded on OMAP and it fixes their problem.  Now it should be (more)
  solid.

  The rest i compilation, Kconfig and driver fixes.  Some tagged for
  stable.

  Summary:

   - Fix a NULL pointer dereference when we are searching the GPIO
     device list but one of the devices have been removed (struct
     gpio_chip pointer is NULL).

   - Fix unaligned reference counters: we were ending on +3 after all
     said and done.  It should be 0.  Remove an extraneous get_device(),
     and call cdev_del() followed by device_del() in gpiochip_remove()
     instead and the count goes to zero and calls the release() function
     properly.

   - Fix a compile warning due to a missing #include in the OF/device
     tree portions.

   - Select ANON_INODES for GPIOLIB, we're using that for our character
     device.  Some randconfig tests disclosed the problem.

   - Make sure the Zynq driver clock runs also without CONFIG_PM enabled

   - Fix an off-by-one error in the 104-DIO-48E driver

   - Fix warnings in bcm_kona_gpio_reset()"

* tag 'gpio-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: bcm-kona: fix bcm_kona_gpio_reset() warnings
  gpio: select ANON_INODES
  gpio: include <linux/io-mapping.h> in gpiolib-of
  gpiolib: Fix unaligned used of reference counters
  gpiolib: Fix NULL pointer deference
  gpio: zynq: initialize clock even without CONFIG_PM
  gpio: 104-dio-48e: Fix control port offset computation off-by-one error

Pull SCSI fixes from James Bottomley:
 "Two current fixes:

   - one affects Qemu CD ROM emulation, which stopped working after the
     updates in SCSI to require VPD pages from all conformant devices.

     Fix temporarily by blacklisting Qemu (we can relax later when they
     come into compliance).

   - The other is a fix to the optimal transfer size.  We set up a
     minefield for ourselves by being confused about whether the limits
     are in bytes or sectors (SCSI optimal is in blocks and the queue
     parameter is in bytes).

     This tries to fix the problem (wrong setting for queue limits
     max_sectors) and make the problem more obvious by introducing a
     wrapper function"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  sd: Fix rw_max for devices that report an optimal xfer size
  scsi: Add QEMU CD-ROM to VPD Inquiry Blacklist

Pull i2c fixes from Wolfram Sang:

 - a bigger fix for i801 to finally be able to be loaded on some
   machines again

 - smaller driver fixes

 - documentation update because of a renamed file

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mux: reg: Provide of_match_table
  i2c: mux: refer to i2c-mux.txt
  i2c: octeon: Avoid printk after too long SMBUS message
  i2c: octeon: Missing AAK flag in case of I2C_M_RECV_LEN
  i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR

Pull DeviceTree fixes from Rob Herring:

 - fix unflatten_dt_nodes when dad parameter is set.

 - add vendor prefixes for TechNexion and UniWest

 - documentation fix for Marvell BT

 - OF IRQ kerneldoc fixes

 - restrict CMA alignment adjustments to non dma-coherent

 - a couple of warning fixes in reserved-memory code

 - DT maintainers updates

* tag 'devicetree-fixes-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  drivers: of: add definition of early_init_dt_alloc_reserved_memory_arch
  drivers/of: Fix depth for sub-tree blob in unflatten_dt_nodes()
  drivers: of: Fix of_pci.h header guard
  dt-bindings: Add vendor prefix for TechNexion
  of: add vendor prefix for UniWest
  dt: bindings: fix documentation for MARVELL's bt-sd8xxx wireless device
  of: add missing const for of_parse_phandle_with_args() in !CONFIG_OF
  of: silence warnings due to max() usage
  drivers: of: of_reserved_mem: fixup the CMA alignment not to affect dma-coherent
  of: irq: fix of_irq_get[_byname]() kernel-doc
  MAINTAINERS: DeviceTree maintainer updates

Merge tag '20160610_uvc_compat_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux

Pull uvc compat XU ioctl fixes from Andy Lutomirski:
 "uvc's compat XU ioctls go through tons of potentially buggy
  indirection.  The first patch removes the indirection.  The second one
  cleans up the code.

  Compile-tested only.  I have the hardware, but I have absolutely no
  idea what XU does, how to use it, what software to recompile as
  32-bit, or what to test in that software"

* tag '20160610_uvc_compat_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux:
  uvc_v4l2: Simplify compat ioctl implementation
  uvc: Forward compat ioctls to their handlers directly

The uvc compat ioctl implementation seems to have copied user data
for no good reason.  Remove a bunch of copies.
Signed-off-by: Andy Lutomirski <luto@kernel.org>

The current code goes through a lot of indirection just to call a
known handler.  Simplify it: just call the handlers directly.

Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>

Pull btrfs fixes from Chris Mason:
 "Has some fixes and some new self tests for btrfs.  The self tests are
  usually disabled in the .config file (unless you're doing btrfs dev
  work), and this bunch is meant to find problems with the 64K page size
  patches.

  Jeff has a patch to help people see if they are using the hardware
  assist crc32c module, which really helps us nail down problems when
  people ask why crcs are using so much CPU.

  Otherwise, it's small fixes"

* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: self-tests: Fix extent buffer bitmap test fail on BE system
  Btrfs: self-tests: Fix test_bitmaps fail on 64k sectorsize
  Btrfs: self-tests: Use macros instead of constants and add missing newline
  Btrfs: self-tests: Support testing all possible sectorsizes and nodesizes
  Btrfs: self-tests: Execute page straddling test only when nodesize < PAGE_SIZE
  btrfs: advertise which crc32c implementation is being used at module load
  Btrfs: add validadtion checks for chunk loading
  Btrfs: add more validation checks for superblock
  Btrfs: clear uptodate flags of pages in sys_array eb
  Btrfs: self-tests: Support non-4k page size
  Btrfs: Fix integer overflow when calculating bytes_per_bitmap
  Btrfs: test_check_exists: Fix infinite loop when searching for free space entries
  Btrfs: end transaction if we abort when creating uuid root
  btrfs: Use __u64 in exported linux/btrfs.h.

Merge tag 'powerpc-4.7-3Michael Ellerman:' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc fixes from
 - ptrace: Fix out of bounds array access warning from Khem Raj
 - pseries: Fix PCI config address for DDW from Gavin Shan
 - pseries: Fix IBM_ARCH_VEC_NRCORES_OFFSET since POWER8NVL was added
   from Michael Ellerman
 - of: fix autoloading due to broken modalias with no 'compatible' from
   Wolfram Sang
 - radix: Fix always false comparison against MMU_NO_CONTEXT from Aneesh
   Kumar K.V
 - hash: Compute the segment size correctly for ISA 3.0 from Aneesh
   Kumar K.V
 - nohash: Fix build break with 64K pages from Michael Ellerman

* tag 'powerpc-4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/nohash: Fix build break with 64K pages
  powerpc/mm/hash: Compute the segment size correctly for ISA 3.0
  powerpc/mm/radix: Fix always false comparison against MMU_NO_CONTEXT
  of: fix autoloading due to broken modalias with no 'compatible'
  powerpc/pseries: Fix IBM_ARCH_VEC_NRCORES_OFFSET since POWER8NVL was added
  powerpc/pseries: Fix PCI config address for DDW
  powerpc/ptrace: Fix out of bounds array access warning