- 20 Oct, 2016 1 commit
-
-
Junichi Nomura authored
commit 2a708cff upstream. __dm_destroy() takes io_barrier SRCU lock (dm_get_live_table) and suspend_lock in reverse order. Doing so can cause AB-BA deadlock: __dm_destroy dm_swap_table --------------------------------------------------- mutex_lock(suspend_lock) dm_get_live_table() srcu_read_lock(io_barrier) dm_sync_table() synchronize_srcu(io_barrier) .. waiting for dm_put_live_table() mutex_lock(suspend_lock) .. waiting for suspend_lock Fix this by taking the locks in proper order. Signed-off-by:
Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Fixes: ab7c7bb6 ("dm: hold suspend_lock while suspending device during device deletion") Acked-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
- 17 Oct, 2016 9 commits
-
-
Jiri Slaby authored
-
James Hogan authored
commit 91e4f1b6 upstream. When a guest TLB entry is replaced by TLBWI or TLBWR, we only invalidate TLB entries on the local CPU. This doesn't work correctly on an SMP host when the guest is migrated to a different physical CPU, as it could pick up stale TLB mappings from the last time the vCPU ran on that physical CPU. Therefore invalidate both user and kernel host ASIDs on other CPUs, which will cause new ASIDs to be generated when it next runs on those CPUs. We're careful only to do this if the TLB entry was already valid, and only for the kernel ASID where the virtual address it mapped is outside of the guest user address range. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
-
Thomas Huth authored
commit fa73c3b2 upstream. The MMCR2 register is available twice, one time with number 785 (privileged access), and one time with number 769 (unprivileged, but it can be disabled completely). In former times, the Linux kernel was using the unprivileged register 769 only, but since commit 8dd75ccb ("powerpc: Use privileged SPR number for MMCR2"), it uses the privileged register 785 instead. The KVM-PR code then of course also switched to use the SPR 785, but this is causing older guest kernels to crash, since these kernels still access 769 instead. So to support older kernels with KVM-PR again, we have to support register 769 in KVM-PR, too. Fixes: 8dd75ccbSigned-off-by:
Thomas Huth <thuth@redhat.com> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Uwe Kleine-König authored
commit 88003fb1 upstream. This fixes a compile failure: drivers/built-in.o: In function `wm8350_i2c_probe': core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c' Makefile:953: recipe for target 'vmlinux' failed Fixes: 52b461b8 ("mfd: Add regmap cache support for wm8350") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Dan Carpenter authored
commit 9a6dc644 upstream. set_bit() and clear_bit() take the bit number so this code is really doing "1 << (1 << irq)" which is a double shift bug. It's done consistently so it won't cause a problem unless "irq" is more than 4. Fixes: 70c6cce0 ('mfd: Support 88pm80x in 80x driver') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Takashi Sakamoto authored
commit 8da08ca0 upstream. Currently, usb-line6 module exports an array of MIDI manufacturer ID and usb-pod module uses it. However, the declaration is not the definition in common header. The difference is explicit length of array. Although compiler calculates it and everything goes well, it's better to use the same representation between definition and declaration. This commit fills the length of array for usb-line6 module. As a small good sub-effect, this commit suppress below warnings from static analysis by sparse v0.5.0. sound/usb/line6/driver.c:274:43: error: cannot size expression sound/usb/line6/driver.c:275:16: error: cannot size expression sound/usb/line6/driver.c:276:16: error: cannot size expression sound/usb/line6/driver.c:277:16: error: cannot size expression Fixes: 705ececd ("Staging: add line6 usb driver") Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit db685779 upstream. The pointer callbacks of ali5451 driver may return the value at the boundary occasionally, and it results in the kernel warning like snd_ali5451 0000:00:06.0: BUG: , pos = 16384, buffer size = 16384, period size = 1024 It seems that folding the position offset is enough for fixing the warning and no ill-effect has been seen by that. Reported-by:
Enrico Mioso <mrkiko.rs@gmail.com> Tested-by:
-
Alexander Graf authored
commit a5948fa0 upstream. In parallel to the Processor ID Register (PIR) threaded POWER8 also adds a Thread ID Register (TIR). Since PR KVM doesn't emulate more than one thread per core, we can just always expose 0 here. Signed-off-by:
Alexander Graf <agraf@suse.de> Signed-off-by:
-
Alexander Graf authored
commit f8f6eb0d upstream. When we expose a POWER8 CPU into the guest, it will start accessing PMU SPRs that we don't emulate. Just ignore accesses to them. Signed-off-by:
-
- 07 Oct, 2016 30 commits
-
-
Jann Horn authored
commit 3dfb7d8c upstream. It looks like smack and yama weren't aware that the ptrace mode can have flags ORed into it - PTRACE_MODE_NOAUDIT until now, but only for /proc/$pid/stat, and with the PTRACE_MODE_*CREDS patch, all modes have flags ORed into them. [js] no smack changes in 3.12 as the code is not there yet Signed-off-by:
Jann Horn <jann@thejh.net> Acked-by:
Kees Cook <keescook@chromium.org> Acked-by:
Casey Schaufler <casey@schaufler-ca.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Morris <james.l.morris@oracle.com> Cc: "Serge E. Hallyn" <serge.hallyn@ubuntu.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Prarit Bhargava authored
commit a59b679a upstream. ACPICA commit 7bb77313091e52a846df4c9c2bea90be31bfb9d8 Eliminate warnings for "not found" _Sx errors, since these are optional. Original NOT_FOUND status is still returned. Original changes by Prarit Bhargava. ACPICA BZ 1208. Link: https://github.com/acpica/acpica/commit/7bb77313 Link: https://bugs.acpica.org/show_bug.cgi?id=1208Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: "Charles (Chas) Williams" <ciwillia@brocade.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit ab21b63e upstream. This reverts commit e6c7efdc. Turns out it was totally wrong. The memory is supposed to be bound to the kref, as the original code was doing correctly, not the device/driver binding as the devm_kzalloc() would cause. This fixes an oops when read would be called after the device was unbound from the driver. Reported-by:
Ladislav Michl <ladis@linux-mips.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Kyle Jones authored
commit decc5360 upstream. Signed-off-by:
Kyle Jones <kyle@kf5jwc.us> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 2fae9e5a upstream. This patch fixes a NULL pointer dereference caused by a race codition in the probe function of the legousbtower driver. It re-structures the probe function to only register the interface after successfully reading the board's firmware ID. The probe function does not deregister the usb interface after an error receiving the devices firmware ID. The device file registered (/dev/usb/legousbtower%d) may be read/written globally before the probe function returns. When tower_delete is called in the probe function (after an r/w has been initiated), core dev structures are deleted while the file operation functions are still running. If the 0 address is mappable on the machine, this vulnerability can be used to create a Local Priviege Escalation exploit via a write-what-where condition by remapping dev->interrupt_out_buffer in tower_write. A forged USB device and local program execution would be required for LPE. The USB device would have to delay the control message in tower_probe and accept the control urb in tower_open whilst guest code initiated a write to the device file as tower_delete is called from the error in tower_probe. This bug has existed since 2003. Patch tested by emulated device. Reported-by:
James Patrick-Evans <james@jmp-e.com> Tested-by:
-
Konstantin Shkolnyy authored
commit a377f9e9 upstream. A bug in the CRTSCTS handling caused RTS to alternate between CRTSCTS=0 => "RTS is transmit active signal" and CRTSCTS=1 => "RTS is used for receive flow control" instead of CRTSCTS=0 => "RTS is statically active" and CRTSCTS=1 => "RTS is used for receive flow control" This only happened after first having enabled CRTSCTS. Signed-off-by:
Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Fixes: 39a66b8d ("[PATCH] USB: CP2101 Add support for flow control") [johan: reword commit message ] Signed-off-by:
Johan Hovold <johan@kernel.org> [johan: backport to 4.4 ] Signed-off-by:
-
Alex Vesker authored
commit e5ac40cd upstream. Because of an incorrect bit-masking done on the join state bits, when handling a join request we failed to detect a difference between the group join state and the request join state when joining as send only full member (0x8). This caused the MC join request not to be sent. This issue is relevant only when SRIOV is enabled and SM supports send only full member. This fix separates scope bits and join states bits a nibble each. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Alex Vesker authored
commit 344bacca upstream. This fix solves a race between light flush and on the fly joins. Light flush doesn't set the device to down and unset IPOIB_OPER_UP flag, this means that if while flushing we have a MC join in progress and the QP was attached to BC MGID we can have a mismatches when re-attaching a QP to the BC MGID. The light flush would set the broadcast group to NULL causing an on the fly join to rejoin and reattach to the BC MCG as well as adding the BC MGID to the multicast list. The flush process would later on remove the BC MGID and detach it from the QP. On the next flush the BC MGID is present in the multicast list but not found when trying to detach it because of the previous double attach and single detach. [18332.714265] ------------[ cut here ]------------ [18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core] ... [18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 [18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000 [18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300 [18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280 [18332.796199] Call Trace: [18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c [18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0 [18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20 [18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core] [18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib] [18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib] [18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib] [18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib] [18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0 [18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40 [18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80 [18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib] [18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib] [18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30 [18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50 [18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170 [18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0 [18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50 [18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0 [18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0 [18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0 [18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25 [18332.894727] ---[ end trace 09ebbe31f831ef17 ]--- Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events") Signed-off-by:
-
Erez Shitrit authored
commit 68c6bcdd upstream. The function send_leave sets the member: group->query_id (group->query_id = ret) after calling the sa_query, but leave_handler can be executed before the setting and it might delete the group object, and will get a memory corruption. Additionally, this patch gets rid of group->query_id variable which is not used. Fixes: faec2f7b ('IB/sa: Track multicast join/leave requests') Signed-off-by:
Erez Shitrit <erezsh@mellanox.com> Signed-off-by:
-
Erez Shitrit authored
commit 546481c2 upstream. When a new CM connection is being requested, ipoib driver copies data from the path pointer in the CM/tx object, the path object might be invalid at the point and memory corruption will happened later when now the CM driver will try using that data. The next scenario demonstrates it: neigh_add_path --> ipoib_cm_create_tx --> queue_work (pointer to path is in the cm/tx struct) #while the work is still in the queue, #the port goes down and causes the ipoib_flush_paths: ipoib_flush_paths --> path_free --> kfree(path) #at this point the work scheduled starts. ipoib_cm_tx_start --> copy from the (invalid)path pointer: (memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);) -> memory corruption. To fix that the driver now starts the CM/tx connection only if that specific path exists in the general paths database. This check is protected with the relevant locks, and uses the gid from the neigh member in the CM/tx object which is valid according to the ref count that was taken by the CM/tx. Fixes: 839fcaba ('IPoIB: Connected mode experimental support') Signed-off-by:
-
Radim Krčmář authored
commit dccbfcf5 upstream. If vmcs12 does not intercept APIC_BASE writes, then KVM will handle the write with vmcs02 as the current VMCS. This will incorrectly apply modifications intended for vmcs01 to vmcs02 and L2 can use it to gain access to L0's x2APIC registers by disabling virtualized x2APIC while using msr bitmap that assumes enabled. Postpone execution of vmx_set_virtual_x2apic_mode until vmcs01 is the current VMCS. An alternative solution would temporarily make vmcs01 the current VMCS, but it requires more care. Fixes: 8d14695f ("x86, apicv: add virtual x2apic support") Reported-by:
Jim Mattson <jmattson@google.com> Reviewed-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Peter Ujfalusi authored
commit a8719670 upstream. Fixes: ddd17531 ("ASoC: omap-mcpdm: Clean up with devm_* function") Managed irq request will not doing any good in ASoC probe level as it is not going to free up the irq when the driver is unbound from the sound card. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Reported-by:
Russell King <linux@armlinux.org.uk> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Michael Ellerman authored
commit 66443efa upstream. When booting from an OpenFirmware which supports it, we use the "ibm,client-architecture-support" firmware call to communicate our capabilities to firmware. The format of the structure we pass to firmware is specified in PAPR (Power Architecture Platform Requirements), or the public version LoPAPR (Linux on Power Architecture Platform Reference). Referring to table 244 in LoPAPR v1.1, option vector 5 contains a 4 byte field at bytes 17-20 for the "Platform Facilities Enable". This is followed by a 1 byte field at byte 21 for "Sub-Processor Represenation Level". Comparing to the code, there we have the Platform Facilities options (OV5_PFO_*) at byte 17, but we fail to pad that field out to its full width of 4 bytes. This means the OV5_SUB_PROCESSORS option is incorrectly placed at byte 18. Fix it by adding zero bytes for bytes 18, 19, 20, and comment the bytes to hopefully make it clearer in future. As far as I'm aware nothing actually consumes this value at this time, so the effect of this bug is nil in practice. It does mean we've been incorrectly setting bit 15 of the "Platform Facilities Enable" option for the past ~3 1/2 years, so we should avoid allocating that bit to anything else in future. Fixes: df77c799 ("powerpc/pseries: Update ibm,architecture.vec for PAPR 2.7/POWER8") Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Florian Fainelli authored
commit f823a2aa upstream. wlc_phy_txpower_get_current() does a logical OR of power->flags, which presumes that power.flags was initiliazed earlier by the caller, unfortunately, this is not the case, so make sure we zero out the struct tx_power before calling into wlc_phy_txpower_get_current(). Reported-by: coverity (CID 146011) Fixes: 5b435de0 ("net: wireless: add brcm80211 drivers") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Florian Fainelli authored
commit 5c5fa1f4 upstream. In case dma_mapping_error() returns an error in dma_rxfill, we would be leaking a packet that we allocated with brcmu_pkt_buf_get_skb(). Reported-by: coverity (CID 1081819) Fixes: 67d0cf50 ("brcmsmac: Fix WARNING caused by lack of calls to dma_mapping_error()") Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Chuck Lever authored
commit a4e187d8 upstream. Before commit 778be232 ("NFS do not find client in NFSv4 pg_authenticate"), the Linux callback server replied with RPC_AUTH_ERROR / RPC_AUTH_BADCRED, instead of dropping the CB request. Let's restore that behavior so the server has a chance to do something useful about it, and provide a warning that helps admins correct the problem. Fixes: 778be232 ("NFS do not find client in NFSv4 ...") Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Tested-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Chuck Lever authored
commit 0533b130 upstream. If an RPC program does not set vs_dispatch and pc_func() returns rpc_drop_reply, the server sends a reply anyway containing a single word containing the value RPC_DROP_REPLY (in network byte-order, of course). This is a nonsense RPC message. Fixes: 9e701c61 ("svcrpc: simpler request dropping") Signed-off-by:
-
Dan Carpenter authored
commit 55f1cf83 upstream. The pio_dev[] array has MAX_NR_PIO_DEVICES elements so the > should be >=. Fixes: 5f97f7f9 ('[PATCH] avr32 architecture') Signed-off-by:
-
Arnd Bergmann authored
commit d7e92e15 upstream. When CONFIG_INPUT is disabled, multiple gspca backend drivers print compile-time warnings about unused variables: media/usb/gspca/cpia1.c: In function 'sd_stopN': media/usb/gspca/cpia1.c:1627:13: error: unused variable 'sd' [-Werror=unused-variable] media/usb/gspca/konica.c: In function 'sd_stopN': media/usb/gspca/konica.c:246:13: error: unused variable 'sd' [-Werror=unused-variable] This annotates the variables as __maybe_unused, to let the compiler know that they are declared intentionally. Fixes: ee186fd9 ("[media] gscpa_t613: Add support for the camera button") Fixes: c2f644ae ("[media] gspca_cpia1: Add support for button") Fixes: b517af72 ("V4L/DVB: gspca_konica: New gspca subdriver for konica chipset using cams") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Dan Carpenter authored
commit e44c153b upstream. The code is checking for negative returns but it should be checking for zero. Fixes: aab3125c ('[media] em28xx: add support for registering multiple i2c buses') Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
James Hogan authored
commit cdf8b463 upstream. AT_VECTOR_SIZE_ARCH should be defined with the maximum number of NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined for tile at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for the VDSO address. This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for AT_BASE_PLATFORM which tile doesn't use, but lets define it now and add the comment above ARCH_DLINFO as found in several other architectures to remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to date. Fixes: 4a556f4f ("tile: implement gettimeofday() via vDSO") Signed-off-by:
Chris Metcalf <cmetcalf@mellanox.com> Signed-off-by:
-
Nishanth Menon authored
commit 61dc0a44 upstream. pm_runtime_get_sync does return a error value that must be checked for error conditions, else, due to various reasons, the device maynot be enabled and the system will crash due to lack of clock to the hardware module. Before: 12.562784] [00000000] *pgd=fe193835 12.562792] Internal error: : 1406 [#1] SMP ARM [...] 12.562864] CPU: 1 PID: 241 Comm: modprobe Not tainted 4.7.0-rc4-next-20160624 #2 12.562867] Hardware name: Generic DRA74X (Flattened Device Tree) 12.562872] task: ed51f140 ti: ed44c000 task.ti: ed44c000 12.562886] PC is at omap4_rng_init+0x20/0x84 [omap_rng] 12.562899] LR is at set_current_rng+0xc0/0x154 [rng_core] [...] After the proper checks: [ 94.366705] omap_rng 48090000.rng: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 94.375767] omap_rng 48090000.rng: Failed to runtime_get device -19 [ 94.382351] omap_rng 48090000.rng: initialization failed. Fixes: 665d92fa ("hwrng: OMAP: convert to use runtime PM") Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Russell King authored
commit 06dfe5cc upstream. SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for the PCMCIA socket class. PCMCIA used to handle suspend/resume via the socket hosting device, which happened at normal device suspend/resume time. However, the referenced commit changed this: much of the resume now happens much earlier, in the noirq resume handler of dev_pm_ops. However, on SA1111, the PCMCIA device is not accessible as the SA1111 has not been resumed at _noirq time. It's slightly worse than that, because the SA1111 has already been put to sleep at _noirq time, so suspend doesn't work properly. Fix this by converting the core SA1111 code to use dev_pm_ops as well, and performing its own suspend/resume at noirq time. This fixes these errors in the kernel log: pcmcia_socket pcmcia_socket0: time out after reset pcmcia_socket pcmcia_socket1: time out after reset and the resulting lack of PCMCIA cards after a S2RAM cycle. Fixes: d7646f76 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Russell King authored
commit da60626e upstream. Clear the current reset status prior to rebooting the platform. This adds the bit missing from 04fef228 ("[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage"). Fixes: 04fef228 ("[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage") Signed-off-by:
-
Nicolas Iooss authored
commit ae6c33ba upstream. Commit bbeddf52 ("printk: move braille console support into separate braille.[ch] files") moved the parsing of braille-related options into _braille_console_setup(), changing the type of variable str from char* to char**. In this commit, memcmp(str, "brl,", 4) was correctly updated to memcmp(*str, "brl,", 4) but not memcmp(str, "brl=", 4). Update the code to make "brl=" option work again and replace memcmp() with strncmp() to make the compiler able to detect such an issue. Fixes: bbeddf52 ("printk: move braille console support into separate braille.[ch] files") Link: http://lkml.kernel.org/r/20160823165700.28952-1-nicolas.iooss_linux@m4x.orgSigned-off-by:
Nicolas Iooss <nicolas.iooss_linux@m4x.org> Cc: Joe Perches <joe@perches.com> Signed-off-by:
-
Paul Burton authored
commit 305723ab upstream. Malta boards used with CPU emulators feature a switch to disable use of an IOCU. Software has to check this switch & ignore any present IOCU if the switch is closed. The read used to do this was unsafe for 64 bit kernels, as it simply casted the address 0xbf403000 to a pointer & dereferenced it. Whilst in a 32 bit kernel this would access kseg1, in a 64 bit kernel this attempts to access xuseg & results in an address error exception. Fix by accessing a correctly formed ckseg1 address generated using the CKSEG1ADDR macro. Whilst modifying this code, define the name of the register and the bit we care about within it, which indicates whether PCI DMA is routed to the IOCU or straight to DRAM. The code previously checked that bit 0 was also set, but the least significant 7 bits of the CONFIG_GEN0 register contain the value of the MReqInfo signal provided to the IOCU OCP bus, so singling out bit 0 makes little sense & that part of the check is dropped. Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Fixes: b6d92b4a ("MIPS: Add option to disable software I/O coherency.") Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Kees Cook <keescook@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14187/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Will Deacon authored
commit 3a402a70 upstream. When TIF_SINGLESTEP is set for a task, the single-step state machine is enabled and we must take care not to reset it to the active-not-pending state if it is already in the active-pending state. Unfortunately, that's exactly what user_enable_single_step does, by unconditionally setting the SS bit in the SPSR for the current task. This causes failures in the GDB testsuite, where GDB ends up missing expected step traps if the instruction being stepped generates another trap, e.g. PTRACE_EVENT_FORK from an SVC instruction. This patch fixes the problem by preserving the current state of the stepping state machine when TIF_SINGLESTEP is set on the current thread. Cc: <stable@vger.kernel.org> Reported-by:
Yao Qi <yao.qi@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Srinivas Ramana authored
commit 117e5e9c upstream. If the bootloader uses the long descriptor format and jumps to kernel decompressor code, TTBCR may not be in a right state. Before enabling the MMU, it is required to clear the TTBCR.PD0 field to use TTBR0 for translation table walks. The commit dbece458 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but doesn't consider all the bits for the size of TTBCR.N. Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to indicate the use of TTBR0 and the correct base address width. Fixes: dbece458 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores") Acked-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Srinivas Ramana <sramana@codeaurora.org> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Dan Carpenter authored
commit f4693b08 upstream. We can't assign -EINVAL to a u16. Fixes: 3948f0e0 ('usb: add Freescale QE/CPM USB peripheral controller driver') Acked-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Sara Sharon authored
commit d5d0689a upstream. This fixes a pretty ancient bug that hasn't manifested itself until now. The scratchbuf for command queue is allocated only for 32 slots but is accessed with the queue write pointer - which can be up to 256. Since the scratch buf size was 16 and there are up to 256 TFDs we never passed a page boundary when accessing the scratch buffer, but when attempting to increase the size of the scratch buffer a panic was quick to follow when trying to access the address resulted in a page boundary. Signed-off-by:
Sara Sharon <sara.sharon@intel.com> Fixes: 38c0f334 ("iwlwifi: use coherent DMA memory for command header") Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
-
