Pull i2c fixes from Wolfram Sang:
 "A set of driver bugfixes for the I2C subsystem"

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: uniphier-f: fix violation of tLOW requirement for Fast-mode
  i2c: uniphier: fix violation of tLOW requirement for Fast-mode
  i2c: uniphier-f: fill TX-FIFO only in IRQ handler for repeated START
  i2c: uniphier-f: fix timeout error after reading 8 bytes
  i2c: scmi: Fix probe error on devices with an empty SMB0001 ACPI device node
  i2c: axxia: properly handle master timeout
  i2c: rcar: check bus state before reinitializing
  i2c: nvidia-gpu: limit reads also for combined messages
  i2c: nvidia-gpu: adhere to I2C fault codes

Pull dmaengine fixes from Vinod Koul:
 "Another pull request for dmaengine. We got bunch of fixes early this
  week and all are tagged to stable. Hope this is last fix for this
  cycle:

   - Fix imx-sdma handling of channel terminations, this involves
     reverting two commits and implement async termination

   - Fix cppi dma channel deletion from pending list on stop

   - Fix FIFO size for dw controller in Intel Merrifield"

* tag 'dmaengine-fix-4.20-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: dw: Fix FIFO size for Intel Merrifield
  dmaengine: cppi41: delete channel from pending list when stop channel
  dmaengine: imx-sdma: use GFP_NOWAIT for dma descriptor allocations
  dmaengine: imx-sdma: implement channel termination via worker
  Revert "dmaengine: imx-sdma: alloclate bd memory from dma pool"
  Revert "dmaengine: imx-sdma: Use GFP_NOWAIT for dma allocations"

Pull drm fixes from Dave Airlie:
 "There's a bit more in here than I'd like, and I'm hoping things calm
  down when I'm out.

  msm:
   - a bunch of display fixes for the new DPU
   - a couple of command submission fixes

  omap:
   - some DSI fixes

  ast:
   - driver unload crash fix

  core:
   - fix the lease uevent so userspace can distinguish it

  amd:
   - fix a bpc regression
   - fix lru handling regression
   - fixed firmware support for new GPUs
   - power management fixes for vega20"

* tag 'drm-fixes-2018-12-07' of git://anongit.freedesktop.org/drm/drm: (37 commits)
  drm/ast: Fix connector leak during driver unload
  drm/amdgpu/vcn: Update vcn.cur_state during suspend
  drm/amd/display: Fix overflow/truncation from strncpy.
  drm/amd/powerplay: improve OD code robustness
  drm/amdgpu: enlarge maximum waiting time of KIQ
  drm/fb-helper: Fix typo in parameter description
  drm/amd/powerplay: support SoftMin/Max setting for some specific DPM
  drm/amd/powerplay: issue pre-display settings for display change event
  drm/amd/powerplay: support new pptable upload on Vega20
  drm/amdgpu/gmc8: always load MC firmware in the driver
  drm/amdgpu/gmc8: update MC firmware for polaris
  drm/amdgpu: update mc firmware image for polaris12 variants
  drm/msm: Fix error return checking
  drm/msm/dpu: Ignore alpha for XBGR8888 format
  drm/msm: dpu: Fix "WARNING: invalid free of devm_ allocated data"
  drm/msm/hdmi: Drop pointless static qualifier in msm_hdmi_bind()
  drm/msm: Move fence put to where failure occurs
  drm/msm: dpu: Don't set legacy plane->crtc pointer
  drm/msm/gpu: Don't map command buffers with nr_relocs equal to 0
  drm/msm/hdmi: Enable HPD after HDMI IRQ is set up
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "This is mainly fallout from the updates to the SUNRPC code that is
  being triggered from less common combinations of NFS mount options.

  Highlights include:

  Stable fixes:
   - Fix a page leak when using RPCSEC_GSS/krb5p to encrypt data.

  Bugfixes:
   - Fix a regression that causes the RPC receive code to hang
   - Fix call_connect_status() so that it handles tasks that got
     transmitted while queued waiting for the socket lock.
   - Fix a memory leak in call_encode()
   - Fix several other connect races.
   - Fix receive code error handling.
   - Use the discard iterator rather than MSG_TRUNC for compatibility
     with AF_UNIX/AF_LOCAL sockets.
   - nfs: don't dirty kernel pages read by direct-io
   - pnfs/Flexfiles fix to enforce per-mirror stateid only for NFSv4
     data servers"

* tag 'nfs-for-4.20-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Don't force a redundant disconnection in xs_read_stream()
  SUNRPC: Fix up socket polling
  SUNRPC: Use the discard iterator rather than MSG_TRUNC
  SUNRPC: Treat EFAULT as a truncated message in xs_read_stream_request()
  SUNRPC: Fix up handling of the XDRBUF_SPARSE_PAGES flag
  SUNRPC: Fix RPC receive hangs
  SUNRPC: Fix a potential race in xprt_connect()
  SUNRPC: Fix a memory leak in call_encode()
  SUNRPC: Fix leak of krb5p encode pages
  SUNRPC: call_connect_status() must handle tasks that got transmitted
  nfs: don't dirty kernel pages read by direct-io
  flexfiles: enforce per-mirror stateid only for v4 DSes

Pull ARM spectre fix from Russell King:
 "Exynos folk noticed that CPU hotplug wasn't working with their kernel
  configuration, and have tested this as fixing the problem"

* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: ensure that processor vtables is not lost after boot

Pull ARM fixes from Russell King:
 "Some small fixes that have been accumulated:

   - Chris Cole noticed that in a SMP environment, the DMA cache
     coherence handling can produce undesirable results in a corner
     case

   - Propagate that fix for ARMv7M as well

   - Fix a false positive with source fortification

   - Fix an uninitialised return that Nathan Jones spotted"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8816/1: dma-mapping: fix potential uninitialized return
  ARM: 8815/1: V7M: align v7m_dma_inv_range() with v7 counterpart
  ARM: 8814/1: mm: improve/fix ARM v7_dma_inv_range() unaligned address handling
  ARM: 8806/1: kprobes: Fix false positive with FORTIFY_SOURCE

Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.

tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
  Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
  Fast-mode:     tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.

tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
  Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
  Fast-mode:     tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

- For a repeated START condition, this controller starts data transfer
   immediately after the slave address is written to the TX-FIFO.

 - Once the TX-FIFO empty interrupt is asserted, the controller makes
   a pause even if additional data are written to the TX-FIFO.

Given those circumstances, the data after a repeated START may not be
transferred if the interrupt is asserted while the TX-FIFO is being
filled up. A more reliable way is to append TX data only in the
interrupt handler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I was totally screwed up in commit eaba6878 ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.

It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba6878.

Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.

This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.

I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.

I consulted a hardware engineer, and I got the following information:

UNIPHIER_FI2C_INT_RF
    asserted at the falling edge of SCL at the 8th bit.

UNIPHIER_FI2C_INT_RB
    asserted at the rising edge of SCL at the 9th (ACK) bit.

In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.

Fixes: eaba6878 ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.

This leads to the following error in dmesg:

[    5.222731] cmi: probe of SMB0001:00 failed with error -5

This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.

The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.

The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.

To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull tracing fix from Steven Rostedt:
 "This is a single commit that fixes a bug in uprobes SDT code due to a
  missing mutex protection"

* tag 'trace-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  Uprobes: Fix kernel oops with delayed_uprobe_remove()

Pull sound fixes from Takashi Iwai:
 "Still more incoming fixes than wished at this stage, but all look like
  small and reasonable fixes.

  In addition to the usual HD-audio and USB-audio quirks for various
  devices, two notable changes are included:

   - a fix for USB-audio UAF at probing a malformed descriptor

   - workarounds for PCM rwsem mutex starvation"

* tag 'sound-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G
  ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G
  ALSA: hda/realtek - Add support for Acer Aspire C24-860 headset mic
  ALSA: hda/realtek: ALC286 mic and headset-mode fixups for Acer Aspire U27-880
  ALSA: usb-audio: Fix UAF decrement if card has no live interfaces in card.c
  ALSA: hda/realtek - Fix speaker output regression on Thinkpad T570
  ALSA: pcm: Fix interval evaluation with openmin/max
  ALSA: hda: Add support for AMD Stoney Ridge
  ALSA: usb-audio: Add SMSL D1 to quirks for native DSD support
  ALSA: pcm: Fix starvation on down_write_nonblock()
  ALSA: pcm: Call snd_pcm_unlink() conditionally at closing

Pull C-SKY fixes from Guo Ren:

 - bugfix for tlb_get_pgd() error

 - update MAINTAINERS file for C-SKY drivers

* tag 'csky-4.20-rc6' of github.com:c-sky/csky-linux:
  csky: bugfix tlb_get_pgd error.
  MAINTAINERS: add maintainer for C-SKY drivers

Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.

Fix this by partitioning it as 64 bytes per channel.

Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.

Fixes: 199244d6 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Marek Szyprowski reported problems with CPU hotplug in current kernels.
This was tracked down to the processor vtables being located in an
init section, and therefore discarded after kernel boot, despite being
required after boot to properly initialise the non-boot CPUs.

Arrange for these tables to end up in .rodata when required.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 383fb3ee ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.

Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e613f3c630c7bbc72e04a44b178259b9164d2f6.1543798395.git.sbobroff@linux.ibm.com

UAPI:
- Distinguish lease events from hotplug (Daniel)

Other:
- omap: Restore panel-dpi bus flags (Tomi)
- omap: Fix a couple of dsi issues (Sebastian)

Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205201428.GA35447@art_vandelay

Fixes for 4.20:
- Fix banding regression on 6 bpc panels
- Vega20 fix for six 4k displays
- Fix LRU handling in ttm_buffer_object_transfer
- Use proper MC firmware for newer polaris variants
- Vega20 powerplay fixes
- VCN suspend/resume fix for PCO
- Misc other fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205192934.2857-1-alexander.deucher@amd.com

Merge tag 'msm-fixes-2018-12-04' of https://gitlab.freedesktop.org/seanpaul/dpu-staging into drm-fixes

- Several related to incorrect error checking/handling (Various)
- Prevent IRQ storm on MDP5 HDMI hotplug (Todor)
- Don't capture crash state if unsupported (Sharat)
- Properly grab vblank reference in atomic wait for commit done (Sean)

Cc: Sharat Masetty <smasetty@codeaurora.org>
Cc: Todor Tomov <todor.tomov@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205194207.GY154160@art_vandelay

There could be a race between task exit and probe unregister:

  exit_mm()
  mmput()
  __mmput()                     uprobe_unregister()
  uprobe_clear_state()          put_uprobe()
  delayed_uprobe_remove()       delayed_uprobe_remove()

put_uprobe() is calling delayed_uprobe_remove() without taking
delayed_uprobe_lock and thus the race sometimes results in a
kernel crash. Fix this by taking delayed_uprobe_lock before
calling delayed_uprobe_remove() from put_uprobe().

Detailed crash log can be found at:
  Link: http://lkml.kernel.org/r/000000000000140c370577db5ece@google.com

Link: http://lkml.kernel.org/r/20181205033423.26242-1-ravi.bangoria@linux.ibm.comAcked-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: syzbot+cb1fb754b771caca0a88@syzkaller.appspotmail.com
Fixes: 1cc33161 ("uprobes: Support SDT markers having reference count (semaphore)")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Pull SCSI fixes from James Bottomley:
 "Four obvious bug fixes. The vmw_pscsi is so old that it's amazing
  no-one noticed before now"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: storvsc: Fix a race in sub-channel creation that can cause panic
  scsi: vmw_pscsi: Rearrange code to avoid multiple calls to free_irq during unload
  scsi: libiscsi: Fix NULL pointer dereference in iscsi_eh_session_reset
  scsi: lpfc: fix block guard enablement on SLI3 adapters

Pull ARC fixes/updates from Vineet Gupta

 - Missing reads{x}()/writes{x}() getting in the way of some drivers [Jose Abreu]

 - Builds defaulting to ARCv2 ISA based configsa [Kevin Hilman]

 - Misc fixes

* tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: io.h: Implement reads{x}()/writes{x}()
  ARC: change defconfig defaults to ARCv2
  arc: [devboards] Add support of NFSv3 ACL
  ARC: mm: fix uninitialised signal code in do_page_fault
  ARC: [plat-hsdk] Enable DW APB GPIO support
  ARCv2: boot log unaligned access in use
  ARC: IOC: panic if kernel was started with previously enabled IOC
  ARC: remove redundant 'default n' from Kconfig

This is a full revert of ac5b2c18 ("mm: thp: relax __GFP_THISNODE for
MADV_HUGEPAGE mappings") and a partial revert of 89c83fb5 ("mm, thp:
consolidate THP gfp handling into alloc_hugepage_direct_gfpmask").

By not setting __GFP_THISNODE, applications can allocate remote hugepages
when the local node is fragmented or low on memory when either the thp
defrag setting is "always" or the vma has been madvised with
MADV_HUGEPAGE.

Remote access to hugepages often has much higher latency than local pages
of the native page size.  On Haswell, ac5b2c18 was shown to have a
13.9% access regression after this commit for binaries that remap their
text segment to be backed by transparent hugepages.

The intent of ac5b2c18 is to address an issue where a local node is
low on memory or fragmented such that a hugepage cannot be allocated.  In
every scenario where this was described as a fix, there is abundant and
unfragmented remote memory available to allocate from, even with a greater
access latency.

If remote memory is also low or fragmented, not setting __GFP_THISNODE was
also measured on Haswell to have a 40% regression in allocation latency.

Restore __GFP_THISNODE for thp allocations.

Fixes: ac5b2c18 ("mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings")
Fixes: 89c83fb5 ("mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask")
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A bit earlier in the week as usual, but there's a fix here that should
  go in sooner rather than later.

  Under a combination of circumstance, the direct issue path in blk-mq
  could corrupt data. This wasn't easy to hit, but the ones that are
  affected by it, seem to hit it pretty easily. Full explanation in the
  patch. None of the regular filesystem and storage testing has
  triggered it, even though it's been around since 4.19-rc1.

  Outside of that, whitelist trim tweak for certain Samsung devices for
  libata"

* tag 'for-linus-20181205' of git://git.kernel.dk/linux-block:
  blk-mq: fix corruption with direct issue
  libata: whitelist all SAMSUNG MZ7KM* solid-state disks

Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pull btrfs fix from David Sterba:
 "A patch in 4.19 introduced a sanity check that was too strict and a
  filesystem cannot be mounted.

  This happens for filesystems with more than 10 devices and has been
  reported by a few users so we need the fix to propagate to stable"

* tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable

Pull power management fix from Rafael Wysocki:
 "Revert a problematic recent commit that attempted to fix a system-wide
  suspend issue related to the freezer"

* tag 'pm-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "exec: make de_thread() freezable"

Pull mfd bugfix from Lee Jones:
 "Replace release function in cros_ec_dev"

* tag 'mfd-fixes-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  Revert "mfd: cros_ec: Use devm_kzalloc for private data"

Acer AIO Veriton Z4860G/Z6860G with the same ALC286 codec has issues
with the input from external microphone. The issue can be fixed by
the fixup ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE for Veriton Z4660G.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Acer AIO Veriton Z4660G with ALC286 codec has issue with the input
from external microphones connecting via 'Front Mic' jack. The fixup
ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE enables the jack sensing of
the headset and fix the audio input issue of external microphone.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The Acer AIO Aspire C24-860 with ALC286 can't detect the headset
microphone. Just like another Acer AIO U27-880, it needs a different
pin value for 0x18 and the headset fixup to make headset mic work.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Acer Aspire U27-880(AIO) with ALC286 codec can not detect headset mic
and internal mic not working either. It needs the similar quirk like
Sony laptops to fix headphone jack sensing and enables use of the
internal microphone.

Unfortunately jack sensing for the headset mic is still not working.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If the connection is broken, then xs_tcp_state_change() will take care
of scheduling the socket close as soon as appropriate. xs_read_stream()
just needs to report the error.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

Ensure that we do not exit the socket read callback without clearing
XPRT_SOCK_DATA_READY.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

When discarding message data from the stream, we're better off using
the discard iterator, since that will work with non-TCP streams.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

If the allocator fails before it has reached the target number of pages,
then we need to recheck that we're not seeking past the page buffer.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

The RPC code is occasionally hanging when the receive code fails to
empty the socket buffer due to a partial read of the data. When we
convert that to an EAGAIN, it appears we occasionally leave data in the
socket. The fix is to just keep reading until the socket returns
EAGAIN/EWOULDBLOCK.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Cristian Marussi <cristian.marussi@arm.com>
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>