And move it to hw code on mac.c where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should fix the oops which occurs during module unload
due to the dereferencig of ah upon debugfs exit.

IP: [<46412d6b>] 0x46412d6b
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
last sysfs file: /sys/class/power_supply/BAT0/energy_full
Modules linked in: ath9k(-) ath9k_hw mac80211 ath cfg80211 <bleh>

Pid: 3112, comm: rmmod Not tainted (2.6.32-rc2-wl #101) 9461DUU
EIP: 0060:[<46412d6b>] EFLAGS: 00010246 CPU: 0
EIP is at 0x46412d6b
EAX: f5870004 EBX: f6700d94 ECX: 00000000 EDX: c14313a7
ESI: f5870000 EDI: fb58ce70 EBP: f6661eb4 ESP: f6661ea8
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process rmmod (pid: 3112, ti=f6660000 task=f6579380 task.ti=f6660000)
Stack:
fb57e5e5 f5ca5d50 fb58ce70 f6661ebc fb58629a f6661ec8 c11b715e f5ca5da8
<0> f6661ed8 c1223d98 f5ca5da8 f5ca5ddc f6661eec c1223e6f fb58ce70 fb58ce70
<0> c14958a0 f6661f00 c1222edb fb58ce70 fb58ce70 fb58cebc f6661f1c c12243c9
Call Trace:
[<fb57e5e5>] ? ath_cleanup+0x35/0x50 [ath9k]
[<fb58629a>] ? ath_pci_remove+0x1a/0x20 [ath9k]
[<c11b715e>] ? pci_device_remove+0x1e/0x40
[<c1223d98>] ? __device_release_driver+0x58/0xa0
[<c1223e6f>] ? driver_detach+0x8f/0xa0
[<c1222edb>] ? bus_remove_driver+0x7b/0xb0
[<c12243c9>] ? driver_unregister+0x49/0x80
[<c1158cf2>] ? sysfs_remove_file+0x12/0x20
[<c11b73b5>] ? pci_unregister_driver+0x35/0x90
[<fb586172>] ? ath_pci_exit+0x12/0x20 [ath9k]
[<fb5883ec>] ? ath9k_exit+0x10/0x3d [ath9k]
[<c131971d>] ? mutex_unlock+0xd/0x10
[<c1088c0f>] ? sys_delete_module+0x16f/0x220
[<c10e3d5d>] ? do_munmap+0x23d/0x290
[<c11a629c>] ? trace_hardirqs_off_thunk+0xc/0x10
[<c11a628c>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c1003b41>] ? sysenter_exit+0xf/0x1a
[<c1003b08>] ? sysenter_do_call+0x12/0x3c
Code:  Bad EIP value.
EIP: [<46412d6b>] 0x46412d6b SS:ESP 0068:f6661ea8
CR2: 0000000046412d6b
---[ end trace 847f3b05ff3dcb19 ]---
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The core driver needs to be stopped and then as a last step the
hardware needs to be stopped and its structure free'd. We do this
by moving the core driver cleanup to a new helper ath_clean_core()
and have ath_cleanup() call it. Only as a last step does
ath_cleanup() now free the hw.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is used in several places, ensure we do it right in all
callers by using a helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

debugfs uses the hardware for several debugfs files as such the
hardware must be initialized and available prior to its usage. The
same applies to when we free the hw structs -- free debufs file
entries prior to free'ing the hardware.
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

What this means is we can enable now debug prints without
requiring CONFIG_ATH9K_DEBUG.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 has long provided us the association ID. This isn't useful except
for Power-Save polling which now gets enabled. We can now poll for our
pending frames on the AP during power save.

You can review the details of Power-Save on the wireless wiki:

http://wireless.kernel.org/en/developers/Documentation/ieee80211/power-savingsSigned-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes a regression introduced by patch titled:

"atheros: define shared bssidmask setting"

The register for the BSSID was exchanged for the bssid mask register.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We have access to common->curbssid and common->curaid so just
use those. Note that common->curaid is always 0 so this keeps
our current behaviour of always using 0 for now. Once we fix
storing the association ID passed by mac80211 this will
require no changes here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The trick was to add four bytes whenever this was used. There
are two places where this was missed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should avoid future typos.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There was a typo on the second bssid mask register.
This was caused by the patch titled:

"ath5k: use common curbssid, bssidmask and macaddr"
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix CFG80211_WEXT build dependencies/errors:

ERROR: "cfg80211_wext_siwscan" [drivers/net/wireless/orinoco/orinoco.ko] undefined!
ERROR: "cfg80211_wext_siwmode" [drivers/net/wireless/orinoco/orinoco.ko] undefined!
ERROR: "cfg80211_wext_giwrange" [drivers/net/wireless/orinoco/orinoco.ko] undefined!
ERROR: "cfg80211_wext_giwmode" [drivers/net/wireless/orinoco/orinoco.ko] undefined!
ERROR: "cfg80211_wext_giwname" [drivers/net/wireless/orinoco/orinoco.ko] undefined!
ERROR: "cfg80211_wext_giwscan" [drivers/net/wireless/orinoco/orinoco.ko] undefined!
ERROR: "cfg80211_wext_giwname" [drivers/net/wireless/ipw2x00/ipw2200.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Everything including this header includes net/cfg80211.h, which
includes linux/netdevice.h, which includes linux/ethtool.h already.  Why
slow-down the build, even a little bit?
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also sorts all "source" lines in the wireless/Kconfig.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Simplify the suspend and resume callbacks of ath5k by converting the
driver to struct dev_pm_ops and allowing the PCI PM core to do the
PCI-specific suspend/resume handling.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set firmware and hardware version in wiphy so that user space can access
it.

(Modification from original in favor of cfg80211 ethtool support. -- JWL)

Cc: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It's useful to provide firmware and hardware version to user space and have a
generic interface to retrieve them. Users can provide the version information
in bug reports etc.

Add fields for firmware and hardware version to struct wiphy.

(Dropped nl80211 bits for now and modified remaining bits in favor of
ethtool. -- JWL)

Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Both 1000 & 6000 series NICs contain on-chip OTP memory that
replaces the off-chip EEPROM memory. The nature of OTP means
there is a limited number of times a particular board can go through the
factory flow and be (re)calibrated. As a consequence there will be some boards
that contain EEPROM memory because OTP blocks were full.

In the signature validation routine, iwlwifi needs to make sure
"select bit" and "EEPROM/OTP signature" agree on the type of
NVM to be used to configure the system.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.

Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.

At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.

The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Multiple MPDUs can be aggregated, transmitted, and finally acknowledged
together using a single BA frame. Block ACK (BA) contains
bitmap size of 64*16 bits so the maximum frame count is 64.
The default value of aggregation frame count suggested by uCode is 31 to
achieve best performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill  <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order to support different type of 1000 series NICs we release to
customers before the production release, iwlwifi driver need to support
all the NICs has EEPROM version greater than 0x15c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When uCode detects critical temperature it should send "card state
notification" interrupt to driver and then shut itself down to prevent
overheating. There is a race condition where uCode shuts down before it
can deliver the interrupt to driver.
Additional method provided here for driver to enter CT_KILL state based
on temperature reading.

How it works:
Method 1:
If driver receive "card state notification" interrupt from uCode; it
enters "CT_KILL" state immediately

Method 2:
If the last temperature report by Card reach Critical temperature,
driver will send "statistic notification" request to uCode to verify the
temperature reading, if driver can not get reply from uCode within
300ms, driver will enter CT_KILL state automatically.

Method 3:
If the last temperature report by Card did not reach Critical
temperature, but uCode already shut down due to critical temperature.
All the host commands send to uCode will not get process by uCode;
when command queue reach the limit, driver will check the last reported
temperature reading, if it is within pre-defined margin, enter "CT_KILL"
state immediately. In this case, when uCode ready to exit from "CT_KILL" state,
driver need to restart the adapter in order to reset all the queues and
resume normal operation.

One additional issue being address here, when system is in CT_KILL
state, both tx and rx already stopped, but driver still can send host
command to uCode, it will flood the command queue since card was not
responding; adding STATUS_CT_KILL flag to reject enqueue host commands
to uCode if it is in CT_KILL state, when uCode is ready to come out of
CT_KILL, driver will clear  the STATUS_CT_KILL bit and allow enqueue the host
commands to uCode to recover from CT_KILL state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The file was accidentally added in commit ef2f8d45 ("wl1251: add
wl1251 prefix to all 1251 files"). This happened when I rebased the
patches from a private tree.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add timer based auto deep sleep feature in libertas driver which can be
configured using iwconfig command. This is tested on SD8688, SD8686 cards
with firmware versions 10.38.1.p25, 9.70.4.p0 respectively on 32-bit and 64-bit
platforms. Tests have been done for USB/CS cards to make sure that the patch
won't break USB/CS code. We didn't test the if_spi driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After the incorporation of the patch entitled "wext: refactor", some
of the wireless drivers in drivers/staging fail to build because they
need to have CONFIG_WIRELESS_EXT and CONFIG_WEXT_PRIV defined.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Refactor wext to
 * split out iwpriv handling
 * split out iwspy handling
 * split out procfs support
 * allow cfg80211 to have wireless extensions compat code
   w/o CONFIG_WIRELESS_EXT

After this, drivers need to
 - select WIRELESS_EXT	- for wext support
 - select WEXT_PRIV	- for iwpriv support
 - select WEXT_SPY	- for iwspy support

except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.

Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Linux keeps scan results up to 15 seconds. This can be a problem for fast
moving clients: they get back stale data. But if the kernel reports the age
of the BSS items, then user-space can simply weed out old entries by itself.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>