rtl_eri_read() returns the full 32bit value, therefore there's no
benefit in writing back parts of it only. handle it like the vendor
driver and write the full 32 bit always. Omitting the mask argument
avoids some overhead and makes the code better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2020-05-22

This series contains updates to virtchnl and the ice driver.

Geert Uytterhoeven fixes a data structure alignment issue in the
virtchnl structures.

Henry adds Flow Director support which allows for the redirection on
ntuple rules over six patches.  Initially Henry adds the initial
infrastructure for Flow Director, and then later adds IPv4 and IPv6
support, as well as being able to display the ntuple rules.

Bret add Accelerated Receive Flow Steering (aRFS) support which is used
to steer receive flows to a specific queue.  Fixes a transmit timeout
when the VF link transitions from up/down/up because the transmit and
receive queue interrupts are not enabled as part of VF's link up.  Fixed
an issue when the default VF LAN address is changed and after reset the
PF will attempt to add the new MAC, which fails because it already
exists. This causes the VF to be disabled completely until it is removed
and enabled via sysfs.

Anirudh (Ani) makes a fix where the ice driver needs to call set_mac_cfg
to enable jumbo frames, so ensure it gets called during initialization
and after reset.  Fix bad register reads during a register dump in
ethtool by removing the bad registers.

Paul fixes an issue where the receive Malicious Driver Detection (MDD)
auto reset message was not being logged because it occurred after the VF
reset.

Victor adds a check for compatibility between the Dynamic Device
Personalization (DDP) package and the NIC firmware to ensure that
everything aligns.

Jesse fixes a administrative queue string call with the appropriate
error reporting variable.  Also fixed the loop variables that are
comparing or assigning signed against unsigned values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-05-22

This series contains updates to e1000e, igc and igb.

Many of the patches in this series are fixes, but many of the igc fixes
are based on the recent filter rule handling Andre has been working,
which will not backport to earlier/stable kernels.  The remaining fixes
for e1000e and igb have CC'd stable where applicable.

Andre continue with his refactoring of the filter rule code to help with
reducing the complexity, in multiple patches.  Fix the inconsistent size
of a struct field.  Fixed an issue where filter rules stay active in the
hardware, even after it was deleted, so make sure to disable the filter
rule before deleting.  Fixed an issue with NFC rules which were dropping
valid multicast MAC address.  Fixed how the NFC rules are restored after
the NIC is reset or brought up, so that they are restored in the same order
they were initially setup in.  Fix a potential memory leak when the
driver is unloaded and the NFC rules are not flushed from memory
properly.  Fixed how NFC rule validation handles when a request to
overwrite an existing rule.  Changed the locking around the NFC rule API
calls from spin_locks to mutex locks to avoid unnecessary busy waiting
on lock contention.

Sasha clean up more unused code in the igc driver.

Kai-Heng Feng from Canonical provides three fixes, first has igb report
the speed and duplex as unknown when in runtime suspend.  Fixed e1000e
to pass up the error when disabling ULP mode.  Fixed e1000e performance
by disabling TSO by default for certain MACs.

Vitaly disables S0ix entry and exit flows for ME systems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-05-22

This series includes two updates and one cleanup patch

1) Tang Bim, clean-up with IS_ERR() usage

2) Vlad introduces a new mlx5 kconfig flag for TC support

   This is required due to the high volume of current and upcoming
   development in the eswitch and representors areas where some of the
   feature are TC based such as the downstream patches of MPLSoUDP and
   the following representor bonding support for VF live migration and
   uplink representor dynamic loading.
   For this Vlad kept TC specific code in tc.c and rep/tc.c and
   organized non TC code in representors specific files.

3) Eli Cohen adds support for MPLS over UPD encap and decap TC offloads.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix psample build error when CONFIG_INET is not set/enabled by
bracketing the tunnel code in #ifdef CONFIG_NET / #endif.

../net/psample/psample.c: In function ‘__psample_ip_tun_to_nlattr’:
../net/psample/psample.c:216:25: error: implicit declaration of function ‘ip_tunnel_info_opts’; did you mean ‘ip_tunnel_info_opts_set’? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ever since its first commit 0ca7111a ("phy: add AT803x driver") the
PHY ID mask was set to 0xffffffef. It is unclear to me why this mask was
chosen in the first place. Both the AR8031/AR8033 and the AR8035
datasheets mention it is always the given value:
 - for AR8031/AR8033 its 0x004d/0xd074
 - for AR8035 its 0x004d/0xd072

Unfortunately, I don't have a datasheet for the AR8030. Therefore, we
leave its PHY ID mask untouched. For the PHYs mentioned before use the
handy PHY_ID_MATCH_EXACT() macro.

I've tried to contact the author of the initial commit, but received no
answer so far.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix loop variables that are comparing or assigning signed against
unsigned values, mostly by declaring loop counters as unsigned.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was using rq_last_status where it should have been
using sq_last_status. Fix the string to be using the correct
error reporting variable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The "ethtool -d" handler reads registers in the ice_regs_dump_list array
and returns read values back to the userspace.

The register offsets PFINT0_ITR* are not valid as per the specification
and reading these causes a "unable to handle kernel paging request" bug
in the driver. Remove these registers from ice_regs_dump_list.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.

Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.

Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.

Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.

Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if a unicast MAC is set via ndo_set_vf_mac, the PF driver will
set the VF's dflt_lan_addr.addr once some basic checks have passed. The
VF is then reset. During reset the PF driver will attempt to program the
VF's MAC from the dflt_lan_addr.addr field. This fails when the MAC
already exists on the PF's switch.

This is causing the VF to be completely disabled until removing/enabling
any VFs via sysfs.

Fix this by checking if the unicast MAC exists before triggering a VF
reset directly in ndo_set_vf_mac. Also, add a check if the unicast MAC
is set to the same value as before and return 0 if that is the case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the iavf is loaded and a VF link transitions from up to
down to up again a Tx timeout will be triggered. This happens because
Tx/Rx queue interrupts are only enabled when receiving the
VIRTCHNL_OP_CONFIG_MAP_IRQ message, which happens on reset or initial
iavf driver load, but not when bringing link up. This is problematic
because they are disabled on the VIRTCHNL_OP_DISABLE_QUEUES message,
which is part of bringing a VF's link down. However, they are not
enabled on the VIRTCHNL_OP_ENABLE_QUEUES message, which is part of
bringing a VF's link up.

Fix this by re-enabling the VF's Rx and Tx queue interrupts when they
were previously configured. This is done by first checking to make
sure the previous value in QINT_[R|T]QCTL.MSIX_INDX is not 0, which
is used to represent the OICR in the VF's interrupt space. If the
MSIX_INDX is non-zero then enable the interrupt by setting the
QINT_[R|T]CTL.CAUSE_ENA bit to 1.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Rx MDD auto reset message was not being logged because logging occurred
after the VF reset and the VF MDD data was reinitialized.

Log the Rx MDD auto reset message before triggering the VF reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.

The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.

The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.

In the Rx path the following things can happen:
        1. New aRFS entries are added to the hash table and the state is
           set to ICE_ARFS_INACTIVE so the filter can be updated in HW
           by the ice_service_task path.
        2. aRFS entries have their Rx Queue updated if we receive a
           pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
           The state is set to ICE_ARFS_INACTIVE so the filter can be
           updated in HW by the ice_service_task path.
        3. aRFS entries marked as ICE_ARFS_TODEL are deleted

In the ice_service_task path the following things can happen:
        1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
           updated in HW.
           and their state is updated to ICE_ARFS_ACTIVE.
        2. aRFS entries are deleted from HW and their state is updated
           to ICE_ARFS_TODEL.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Flex-bytes allows for packet matching based on an offset and value. This
is supported via the ethtool user-def option.  It is specified by providing
an offset followed by a 2 byte match value. Offset is measured from the
start of the MAC address.

The following restrictions apply to flex-bytes. The specified offset must
be an even number and be smaller than 0x1fe.

Example usage:

ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 12 dst-port 13 user-def 0x10ffff action 32
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Extend supported filters to allow for IPv6 filters.

Supported fields are: src-ip, dst-ip, src-port, and dst-port
Supported flow-types are: tcp6, udp6, sctp6, ip6

Example usage:

ethtool -N eth0 flow-type tcp6 src-port 12 dst-port 13 \
src-ip fce0::1:34 dst-ip fce0::1:35 action 32
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Support the addition and deletion of IPv4 filters.

Supported fields are: src-ip, dst-ip, src-port, and dst-port
Supported flow-types are: tcp4, udp4, sctp4, ip4

Example usage:

ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 16 dst-port 12 action 32
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.

Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On e.g. m68k, the alignment of 32-bit values is only 2 bytes, leading
to the following:

    ./include/linux/avf/virtchnl.h:147:36: warning: division by zero [-Wdiv-by-zero]
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
					^
    ./include/linux/avf/virtchnl.h:577:1: note: in expansion of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
     VIRTCHNL_CHECK_STRUCT_LEN(272, virtchnl_filter);
     ^~~~~~~~~~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:577:32: error: enumerator value for ‘virtchnl_static_assert_virtchnl_filter’ is not an integer constant
     VIRTCHNL_CHECK_STRUCT_LEN(272, virtchnl_filter);
				    ^~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:147:53: note: in definition of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
							 ^
    ./include/linux/avf/virtchnl.h:147:36: warning: division by zero [-Wdiv-by-zero]
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
					^
    ./include/linux/avf/virtchnl.h:619:1: note: in expansion of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
     VIRTCHNL_CHECK_STRUCT_LEN(16, virtchnl_pf_event);
     ^~~~~~~~~~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:619:31: error: enumerator value for ‘virtchnl_static_assert_virtchnl_pf_event’ is not an integer constant
     VIRTCHNL_CHECK_STRUCT_LEN(16, virtchnl_pf_event);
				   ^~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:147:53: note: in definition of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
							 ^
    ./include/linux/avf/virtchnl.h:147:36: warning: division by zero [-Wdiv-by-zero]
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
					^
    ./include/linux/avf/virtchnl.h:640:1: note: in expansion of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
     VIRTCHNL_CHECK_STRUCT_LEN(12, virtchnl_iwarp_qv_info);
     ^~~~~~~~~~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:640:31: error: enumerator value for ‘virtchnl_static_assert_virtchnl_iwarp_qv_info’ is not an integer constant
     VIRTCHNL_CHECK_STRUCT_LEN(12, virtchnl_iwarp_qv_info);
				   ^~~~~~~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:147:53: note: in definition of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
							 ^
    ./include/linux/avf/virtchnl.h:147:36: warning: division by zero [-Wdiv-by-zero]
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
					^
    ./include/linux/avf/virtchnl.h:647:1: note: in expansion of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
     VIRTCHNL_CHECK_STRUCT_LEN(16, virtchnl_iwarp_qvlist_info);
     ^~~~~~~~~~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:647:31: error: enumerator value for ‘virtchnl_static_assert_virtchnl_iwarp_qvlist_info’ is not an integer constant
     VIRTCHNL_CHECK_STRUCT_LEN(16, virtchnl_iwarp_qvlist_info);
				   ^~~~~~~~~~~~~~~~~~~~~~~~~~
    ./include/linux/avf/virtchnl.h:147:53: note: in definition of macro ‘VIRTCHNL_CHECK_STRUCT_LEN’
      { virtchnl_static_assert_##X = (n)/((sizeof(struct X) == (n)) ? 1 : 0) }
							 ^

Fix this by adding explicit padding to structures with holes.

Reported-by: <noreply@ellerman.id.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Daniel Borkmann says:

====================
pull-request: bpf-next 2020-05-23

The following pull-request contains BPF updates for your *net-next* tree.

We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).

The main changes are:

1) Add a new AF_XDP buffer allocation API to the core in order to help
   lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
   as well as mlx5 have been moved over to the new API and also gained a
   small improvement in performance, from Björn Töpel and Magnus Karlsson.

2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
   in order to allow for e.g. reverse translation of load-balancer backend
   to service address/port tuple from a connected peer, from Daniel Borkmann.

3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
   being non-NULL, e.g. if after an initial test another non-NULL test on
   that pointer follows in a given path, then it can be pruned right away,
   from John Fastabend.

4) Larger rework of BPF sockmap selftests to make output easier to understand
   and to reduce overall runtime as well as adding new BPF kTLS selftests
   that run in combination with sockmap, also from John Fastabend.

5) Batch of misc updates to BPF selftests including fixing up test_align
   to match verifier output again and moving it under test_progs, allowing
   bpf_iter selftest to compile on machines with older vmlinux.h, and
   updating config options for lirc and v6 segment routing helpers, from
   Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.

6) Conversion of BPF tracing samples outdated internal BPF loader to use
   libbpf API instead, from Daniel T. Lee.

7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
   the XDP selftests, from Jesper Dangaard Brouer.

8) Minor improvements to libbpf's internal hashmap implementation, from
   Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since ME systems do not support SLP_S0 in S0ix state, and S0ix entry
and exit flows may cause errors on them it is best to avoid using
e1000e_s0ix_entry_flow and e1000e_s0ix_exit_flow functions.

This was done by creating a struct of all devices that comes with ME
and by checking if the current device has ME.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit b10effb9 ("e1000e: fix buffer overrun while the I219 is
processing DMA transactions") imposes roughly 30% performance penalty.

The commit log states that "Disabling TSO eliminates performance loss
for TCP traffic without a noticeable impact on CPU performance", so
let's disable TSO by default to regain the loss.

CC: stable <stable@vger.kernel.org>
Fixes: b10effb9 ("e1000e: fix buffer overrun while the I219 is processing DMA transactions")
BugLink: https://bugs.launchpad.net/bugs/1802691Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware may stop working if driver failed to disable ULP mode.

Take the return value of e1000_disable_ulp_lpt_lp() into account, and
pass up the error if it fails.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igb device gets runtime suspended when there's no link partner. We can't
get correct speed under that state:
$ cat /sys/class/net/enp3s0/speed
1000

In addition to that, an error can also be spotted in dmesg:
[  385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost

Since device can only be runtime suspended when there's no link partner,
we can skip reading register and let the following logic set speed and
duplex with correct status.

The more generic approach will be wrap get_link_ksettings() with begin()
and complete() callbacks. However, for this particular issue, begin()
calls igb_runtime_resume() , which tries to rtnl_lock() while the lock
is already hold by upper ethtool layer.

So let's take this approach until the igb_runtime_resume() no longer
needs to hold rtnl_lock.

CC: stable <stable@vger.kernel.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable Tidv register, Report Packet Sent, Report Status and
Ethernet CRC flags not in use.
This patch comes to clean up these flags.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During igc_down(), we call igc_nfc_rule_exit() which traverse the NFC
rule list disabling filters one by one. Later on in igc_down() flow
we issue an hardware reset which also clear all filters.  Since we
already reset the hardware, we don't actually need to disable each
filter manually. In order to simplify the code, this patch removes
igc_nfc_rule() altogether.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes adapter->nfc_rule_lock type from spin_lock to mutex
so we avoid unnecessary busy waiting on lock contention.

A closer look at the execution context of NFC rule API users shows that
all of them run in process context. The API users are: ethtool ops,
igc_configure(), called when interface is brought up by user or reset
workequeue thread, igc_down(), called when interface is brought down,
and igc_remove(), called when driver is unloaded.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

None of igc_disable_nfc_rule() callers actually check its returning
value. A closer look at why this function would fail shows that the
only situation is when we try to delete an Ethertype or MAC filter that
doesn't exist.

That situation is very unlikely so we can change igc_del_etype_filter()
and igc_del_mac_filter() logic to "if the filter doesn't exist, we are
done", and keep the logic in igc_disable_nfc_rule() callers simple.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If we try to overwrite an existing rule with the same filter but
different action, we get EEXIST error as shown below.

$ ethtool -N eth0 flow-type ether dst <MACADDR> action 1 loc 10
$ ethtool -N eth0 flow-type ether dst <MACADDR> action 2 loc 10
rmgr: Cannot insert RX class rule: File exists

The second command is expected to overwrite the previous rule in location
10 and succeed.

This patch fixes igc_ethtool_check_nfc_rule() so it also checks the
rules location. In case they match, the rule under evaluation should not
be considered invalid.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If we have RFC rules in adapter->nfc_rule_list when the IGC driver
is unloaded, all rules are leaked. This patch fixes the issue by
introducing the helper igc_flush_nfc_rules() and calling it in
igc_remove(). It also updates igc_set_features() so is reuses the
new helper instead of re-implementing it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Current implementation of igc_ethtool_update_nfc_rule() is a bit
convoluted since it handles too many things: rule lookup, deletion
and addition. This patch breaks it into three functions so we simplify
the code and improve code reuse.

Code related to rule lookup is refactored out to a new function called
igc_get_nfc_rule().

Code related to rule addition is refactored out to a new function called
igc_add_nfc_rule(). This function enables the rule in hardware and adds
it to the adapter's list.

Code related to rule deletion is refactored out to a new function called
igc_del_nfc_rule(). This function disables the rule in hardware, removes
it from adapter's list, and deletes it.

As a byproduct of this refactoring, igc_enable_nfc_rule() and
igc_disable_nfc_rule() are moved to igc_main.c since they are not used
in igc_ethtool.c anymore, and igc_restore_nfc_rules() and igc_nfc_rule_
exit() are moved around to avoid forward declaration.

Also, since this patch already touches igc_ethtool_get_nfc_rule(), it
takes the opportunity to remove the 'match_flags' check. Empty flags
are not allowed to be added so no need to check that.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When network interface is brought up, the driver re-enables the NFC
rules previously configured. However, this is done in reverse order
the rules were added and hardware filters are configured differently.

For example, consider the following rules:

$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:AA queue 0
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:BB queue 1
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:CC queue 2
$ ethtool -N eth0 flow-type ether dst 00:00:00:00:00:DD queue 3

RAL/RAH registers are configure so filter index 1 has address ending
with AA, filter index 2 has address ending in BB, and so on.

If we bring the interface down and up again, RAL/RAH registers are
configured so filter index 1 has address ending in DD, filter index 2
has CC, and so on. IOW, in reverse order we had before bringing the
interface down.

This issue can be fixed by traversing adapter->nfc_rule_list in
backwards when restoring the rules. Since hlist doesn't support
backwards traversal, this patch replaces it by list_head and fixes
igc_restore_nfc_rules() accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Multicast MAC addresses are valid address for NFC rules but
igc_add_mac_filter() is currently rejecting them. In fact, the I225
controller doesn't impose any constraint on the address value so this
patch gets rid of the address validation check in MAC filter APIs.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the 'loc' argument is passed in ethtool, the input rule overwrites
any rule present in that location. In this situation we must disable the
old rule otherwise it is left enabled in hardware. This patch fixes
the issue by always calling igc_disable_nfc_rule() when deleting the
old rule, no matter the value of 'input' argument.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Access to NFC rules stored in adapter->nfc_rule_list is protect by
adapter->nfc_rule_lock. The functions igc_ethtool_get_nfc_rule()
and igc_ethtool_get_nfc_rules() are missing to hold the lock while
accessing rule objects.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The 'sw_idx' field from 'struct igc_nfc_rule' is u16 type but it is
assigned an u32 value in igc_ethtool_init_nfc_rule(). This patch changes
'sw_idx' type to u32 so they match. Also, it makes more sense to call
this field 'location' since it holds the NFC rule location.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Current implementation of igc_ethtool_add_nfc_rule() is quite long and a
bit convoluted so this patch does a code refactoring to improve the
code.

Code related to NFC rule object initialization is refactored out to the
local helper function igc_ethtool_init_nfc_rule(). Likewise, code
related to NFC rule validation is refactored out to another local
helper, igc_ethtool_is_nfc_rule_valid().

RX_CLS_FLOW_DISC check is removed since it is redundant. The macro is
defined as the max value fsp->ring_cookie can have, so checking if
fsp->ring_cookie >= adapter->num_rx_queues is already sufficient.

Finally, some log messages are improved or added, and obvious comments
are removed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>