Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

These have been register compatible so far. However ARCv2 mandates
different pt_regs layout (due to h/w auto save). To keep pt_regs same
for both, we start by removing the assumption - used mainly for block
copies between the 2 structs in signal handling and ptrace
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Previously this macro was overloaded with stack switching, saving SP at right
slot in pt_regs, saving/setup of r25 and setting SP baseline to where
pt_regs->sp is saved (vs. bottom of pt_regs)

Now it only does SP switch, and leaves SP pointing to bottom of pt_regs.

r25 saving is no longer done here to allow for future reordering of
regfile in pt_regs w/o touching this macro
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Returning from pure kernel mode and exception mode use the same code
anyways. Remove one the duplicate blocks
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Elide the need to re-read ECR in Trap handler by ensuring that
EXCEPTION_PROLOGUE does that at the very end just before returning
to Trap handler

ARCv2 EXCEPTION_PROLOGUE already did that, so same for ARcompact and the
common trap handler adjusted to use cached ECR
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

This fixes the possible link/relo errors, since restore_regs will be
provided by ISA code, but called from ARC common code.
The .L prefix reassures binutils that it will be in same compilation
unit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

-EXCEPTION_EPILOGUE introduced
-EXCEPTION_PROLOGUE now also includes reg file saving
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

-common'ize macros for level 1 and level 2 interrupts
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

- Remove the ifdef'ery and write distinct versions for each mmu ver even
  if there is some code duplication
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

That is because __after_dc_op() already reads it for status check, so it
is better anyways to use that "newer" value.

Also reduces the clutter in callers for passing from/to these routines.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

As DW Mobile Storage databook says it's required to use "Hold Register"
if card is enumerated in SDR12 or SDR25 modes.
It means we need to act in the same way as in Altera's Socfpga
implementation - set "use hold reg" bit in commad.

Note that for upstream proper solution would be to remove
dw_mci_pltfm_prepare_command() at all and set the bit right in
dw_mci_prepare_command() for all platforms.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Route all MB originated traffic to DDR Port 1 and keep Port 0 for CPU
traffic only

Basic system parameters
--------------------------------------------------------------------------------------
        Host                 OS Description 				Mhz  tlb   cache  mem   scal
                                                			    pages  line   par   load
                                                      				   bytes
----------------- ------------- --------------------------------------- ---- ----- ----- ------ ----
axs101-sd-2-new-f Linux 3.13.0+ axs101-sd-2-new-fw-old-img-rerun    	739  	8    32 1.1100    1
axs101-sd-3-arc-3 Linux 3.13.9+ axs101-sd-3-arc-3.13-tip-regression 	735  	8    32 1.1000    1
axs101-sd-9-diffe Linux 3.13.11 axs101-sd-9-different-tweak         	740  	8    32 1.0000    1

Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host                 OS  Mhz null null      open slct sig  sig  fork exec sh
                             call  I/O stat clos TCP  inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
axs101-sd Linux 3.13.0+  739 0.50 0.88 5.38 14.6 34.1 0.92 5.18 2135 6555 12.K
axs101-sd Linux 3.13.9+  735 0.50 0.90 5.89 19.2 81.4 0.94 4.08 2560 8559 15.K
axs101-sd Linux 3.13.11  740 0.50 0.88 4.45 17.8 34.4 0.94 3.25 2052 6493 12.K
                                                 ^^^^                     ^^^^
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Earlycon calculates UART clock as "BASE_BAUD * 16". In case of ARC
"BASE_BAUD" is calculated dynamically in runtime, basically it is an
alias to arc_early_base_baud(), which in turn just does
"arc_base_baud/16".

8250 UART on AXS/SDP board uses 33.3MHz clock source which is set in
"arc_base_baud" with this change.

Additional compatibility string "snps,arc-sdp" is introduced as well
because there're different flavours of AXS boards but they all share the
same motherboard and so it's possible to re-use the same code for
motherbord even if CPU daughterboard changes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

The AXS10x platforms consist of a mainboard with peripherals,
on which several daughter cards can be placed. The daughter cards
typically contain a CPU and memory.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Currently, it doesn't invoke the callback but continues to unwind

Also while at it - simplify the code a bit
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Directly return the result of perf_pmu_register() in
arc_pmu_device_probe() instead of assigning and returning variable ret.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

static arc_pmu in the arch/arc/kernel/perf_event.c is not initialized as
it's shadowed by a local variable of the same name in the
arc_pmu_device_probe.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Fixes: 03c94fcf "ARC: perf: make @arc_pmu static global"
CC: <stable@vger.kernel.org>	# 4.1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

* Remove remanants of legacy ARC FPGA platforms (AA4, ML509...)
* Only nsim simulation platform is left, rename platform accordingly
* AA4 DT stuff is compatible with nsim for ARC700 so rename it too
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

With ISS long unsupported, no point in having extension based on it
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Back when ARC700 4.10 was released, the related kernel features were
tied to this config item so they could be disabled in one shot (i.e.
LLOCK/SCOND, SWAPE, RTSC..)

That having happened a while back, all new ARC customers weill get 4.11+
so those features can be assumed to be present and need not be tied to a
top-level (we still retain the ability to individually disable them).

Further, since ARCv2 also shares some of those feautes, removing it
simplifies things a bit in Kconfig
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

ARC GNU tools have had support for arc-linux-* driver for some time now.
This is functionally similar to arc-linux-uclibc-* but uclibc prefix
seemed weird at best when trying to compile the kernel itself.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>