Even when PCI is disabled, ARCH_ALPINE selects ALPINE_MSI triggerring
the following config warning:

warning: (ARCH_ALPINE) selects ALPINE_MSI which has unmet direct
		dependencies (PCI)

This patch makes selection of ALPINE_MSI conditional on PCI.

Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:

- The arm,data-latency and arm,tag-latency properties need 3 cells to
  be valid, otherwise we end up retaining the default 8-cycle latencies
  which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
  rid of it.
- The cache geometry override also leads to lockup and/or general
  misbehaviour. Irritatingly, the manual doesn't state the actual PL310
  configuration, but based on the boardfile code and poking registers
  from the Boot Monitor, it would seem to be 8 sets of 16KB ways.

With that, we can successfully boot to enjoy the fun of mismatched FPUs...

Cc: stable@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

c90bb7b9 enabled the high speed UARTs of the Jetson TK1. Due to a merge
quirk, wrong addresses were introduced. Fix it and use the correct
addresses.

Thierry let me know, that there is another patch (b5896f67 in
linux-next) in preparation which removes all the '0,' prefixes of unit
addresses on Tegra124 and is planned to go upstream in 4.8, so
this patch will get reverted then.

But for the moment, this patch is necessary to fix current misbehaviour.

Fixes: c90bb7b9 ("ARM: tegra: Add high speed UARTs to Jetson TK1 device tree")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Cc: stable@vger.kernel.org # v4.7
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This syscon needs to be looked up by clocks, flash protection
and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This syscon needs to be looked up by flash protection, CLCD
display output settings and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

For unknown reasons, we have to enable three symbols for a platform
to use a reset controller driver, otherwise we get a Kconfig
warning:

warning: (MACH_OX810SE) selects RESET_OXNAS which has unmet direct dependencies (RESET_CONTROLLER)

This selects the other two symbols for oxnas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>

The machine specific header files are exported for traditional
platforms, but not for the ones that use ARCH_MULTIPLATFORM, as
they could conflict with one another.

In case of ARM_SINGLE_ARMV7M, we end up also exporting them,
but that appears to be a mistake, and we should treat it the
same way as ARCH_MULTIPLATFORM here.

'make W=1' warns about this because it passes -Wmissing-includes
to gcc and the directories are not actually present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Three platforms used to have header files in include/mach that
are now all gone, but the removed directories are still being
included, which leads to -Wmissing-include-dirs warnings.

This removes the extra -I flags.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The patch that this was preparing for made it into neither v4.7 nor
v4.8, so we should back this out as well to avoid the opposite
warning:

  arch/arm/configs/aspeed_g5_defconfig:62:warning: symbol value '1' invalid for PRINTK_TIME
  arch/arm/configs/aspeed_g4_defconfig:61:warning: symbol value '1' invalid for PRINTK_TIME

Sorry for not catching this earlier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0ef659a3 ("ARM: aspeed: adapt defconfigs for new CONFIG_PRINTK_TIME")
Cc: stable@vger.kernel.org # v4.7

For rcar-gen2, we build the SMP files even for UP configurations,
and that just broke:

arch/arm/mach-shmobile/built-in.o: In function `shmobile_smp_init_fallback_ops':
pm-rcar-gen2.c:(.init.text+0x40c): undefined reference to `platform_can_secondary_boot'

This adds an compile-time check before the call to platform_can_secondary_boot,
turning the function into an empty stub for UP configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c21af444 ("ARM: shmobile: smp: Add function to prioritize DT SMP")
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the linux-arm-kernel mailing list for the Alpine SoCs.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

A new user of the Kconfig selection of ARCH_REQUIRE_GPIOLIB
has appeared. Replace with just selecting GPIOLIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add RTC source clock as Exynos7 needs source (32.768KHz) clock
for RTC block. Without this currently S3C RTC driver probe is broken
on this SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull more s390 updates from Martin Schwidefsky:

 - some cleanup for the hugetlbfs pte/pmd conversion functions

 - the code to check for the minimum CPU type is converted from
   assembler to C and an informational message is added in case the CPU
   is not new enough to run the kernel

 - bug fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ftrace/jprobes: Fix conflict between jprobes and function graph tracing
  s390: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO
  s390/zcrypt: fix possible memory leak in ap_module_init()
  s390/numa: only set possible nodes within node_possible_map
  s390/als: fix compile with gcov enabled
  s390/facilities: do not generate DWORDS define anymore
  s390/als: print missing facilities on facility mismatch
  s390/als: print machine type on facility mismatch
  s390/als: convert architecture level set code to C
  s390/sclp: move uninitialized data to data section
  s390/zcrypt: Fix zcrypt suspend/resume behavior
  s390/cio: fix premature wakeup during chp configure
  s390/cio: convert cfg_lock mutex to spinlock
  s390/mm: clean up pte/pmd encoding

Merge drm updates from Dave Airlie:
 "This is the main drm pull request for 4.8.

  I'm down with a cold at the moment so hopefully this isn't in too bad
  a state, I finished pulling stuff last week mostly (nouveau fixes just
  went in today), so only this message should be influenced by illness.
  Apologies to anyone who's major feature I missed :-)

  Core:
        Lockless GEM BO freeing
        Non-blocking atomic work
        Documentation changes (rst/sphinx)
        Prep for new fencing changes
        Simple display helpers
        Master/auth changes
        Register/unregister rework
        Loads of trivial patches/fixes.

  New stuff:
        ARM Mali display driver (not the 3D chip)
        sii902x RGB->HDMI bridge

  Panel:
        Support for new panels
        Improved backlight support

  Bridge:
        Convert ADV7511 to bridge driver
        ADV7533 support
        TC358767 (DSI/DPI to eDP) encoder chip support

  i915:
        BXT support enabled by default
        GVT-g infrastructure
        GuC command submission and fixes
        BXT workarounds
        SKL/BKL workarounds
        Demidlayering device registration
        Thundering herd fixes
        Missing pci ids
        Atomic updates

  amdgpu/radeon:
        ATPX improvements for better dGPU power control on PX systems
        New power features for CZ/BR/ST
        Pipelined BO moves and evictions in TTM
        GPU scheduler improvements
        GPU reset improvements
        Overclocking on dGPUs with amdgpu
        Polaris powermanagement enabled

  nouveau:
        GK20A/GM20B volt and clock improvements.
        Initial support for GP100/GP104 GPUs, GP104 will not yet support
        acceleration due to NVIDIA having not released firmware for them as of yet.

  exynos:
        Exynos5433 SoC with IOMMU support.

  vc4:
        Shader validation for branching

  imx-drm:
        Atomic mode setting conversion
        Reworked DMFC FIFO allocation
        External bridge support

  analogix-dp:
        RK3399 eDP support
        Lots of fixes.

  rockchip:
        Lots of small fixes.

  msm:
        DT bindings cleanups
        Shrinker and madvise support
        ASoC HDMI codec support

  tegra:
        Host1x driver cleanups
        SOR reworking for DP support
        Runtime PM support

  omapdrm:
        PLL enhancements
        Header refactoring
        Gamma table support

  arcgpu:
        Simulator support

  virtio-gpu:
        Atomic modesetting fixes.

  rcar-du:
        Misc fixes.

  mediatek:
        MT8173 HDMI support

  sti:
        ASOC HDMI codec support
        Minor fixes

  fsl-dcu:
        Suspend/resume support
        Bridge support

  amdkfd:
        Minor fixes.

  etnaviv:
        Enable GPU clock gating

  hisilicon:
        Vblank and other fixes"

* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
  drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
  drm/nouveau/acpi: fix lockup with PCIe runtime PM
  drm/nouveau/acpi: check for function 0x1B before using it
  drm/nouveau/acpi: return supported DSM functions
  drm/nouveau/acpi: ensure matching ACPI handle and supported functions
  drm/nouveau/fbcon: fix font width not divisible by 8
  drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
  drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
  drm/amdgpu: add query device id and revision id into system info entry at CGS
  drm/amdgpu: add new definition in bif header
  drm/amd/powerplay: rename smum header guards
  drm/amdgpu: enable UVD context buffer for older HW
  drm/amdgpu: fix default UVD context size
  drm/amdgpu: fix incorrect type of info_id
  drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
  drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
  drm/amdgpu: enable UVD VM only on polaris
  drm/amdgpu: increase timeout of IB test
  drm/amdgpu: add destroy session when generate VCE destroy msg.
  drm/amd: fix deadlock of job_list_lock V2
  ...

 Switch to MULTIPLATFORM"

Missed conflict between commit c86f5173 ("ARM: clps711x: Switch to
MULTIPLATFORM") from the arm-soc tree and commit 250e46aa3bb3
("clocksource/drivers/clps_711x: Add the COMPILE_TEST option") from the
clockevents tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Runtime PM fixes, fbcon and nv30 fix.
* 'linux-4.8' of git://github.com/skeggsb/linux:
  drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
  drm/nouveau/acpi: fix lockup with PCIe runtime PM
  drm/nouveau/acpi: check for function 0x1B before using it
  drm/nouveau/acpi: return supported DSM functions
  drm/nouveau/acpi: ensure matching ACPI handle and supported functions
  drm/nouveau/fbcon: fix font width not divisible by 8

Pull ia64 updates from Tony Luck:
 "Miscellaneous ia64 cleanups"

* tag 'please-pull-misc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  ia64: salinfo: use a waitqueue instead a sema down/up combo
  ia64: efi: use timespec64 for persistent clock

Pull 64-bit ARM DT updates from Olof Johansson:
 "Just as the 32-bit contents, the 64-bit device tree branch also
  contains a number of additions this release cycle.

  New platforms:
   - LG LG1313
   - Mediatek MT6755
   - Renesas r8a7796
   - Broadcom 2837

  Other platforms with larger updates are:
   - Nvidia X1 platforms (USB 3.0, regulators, display subsystem)
   - Mediatek MT8173 (display subsystem added)
   - Rockchip RK3399 (a lot of new peripherals)
   - ARM Juno reference implementation (SCPI power domains, coresight,
     thermal)"

* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
  arm64: tegra: Enable HDMI on Jetson TX1
  arm64: tegra: Add sor1_src clock
  arm64: tegra: Add XUSB powergates on Tegra210
  arm64: tegra: Add DPAUX pinctrl bindings
  arm64: tegra: Add ACONNECT bus node for Tegra210
  arm64: tegra: Add audio powergate node for Tegra210
  arm64: tegra: Add regulators for Tegra210 Smaug
  arm64: tegra: Correct Tegra210 XUSB mailbox interrupt
  arm64: tegra: Enable XUSB controller on Jetson TX1
  arm64: tegra: Enable debug serial on Jetson TX1
  arm64: tegra: Add Tegra210 XUSB controller
  arm64: tegra: Add Tegra210 XUSB pad controller
  arm64: tegra: Add DSI panel on Jetson TX1
  arm64: tegra: p2597: Add SDMMC power supplies
  arm64: tegra: Add PMIC support on Jetson TX1
  Revert "ARM64: DTS: meson-gxbb: switch ethernet to real clock"
  arm64: dts: hi6220: Add pl031 RTC support
  arm64: dts: r8a7796/salvator-x: Enable watchdog timer
  arm64: dts: r8a7796: Add RWDT node
  arm64: dts: r8a7796: Use SYSC "always-on" PM Domain
  ...

Pull ARM DT updates from Olof Johansson:
 "Device tree contents continue to be the largest branches we submit.
  This time around, some of the contents worth pointing out is:

  New SoC platforms:
   - Freescale i.MX 7Solo
   - Broadcom BCM23550
   - Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
   - Hisilicon HI3519
   - Renesas R8A7792

  Some of the other delta that is sticking out, line-count wise:
   - Exynos moves of IP blocks under an SoC bus, which causes a large
     delta due to indentation changes
   - a new Tegra K1 board: Apalis
   - a bunch of small updates to many Allwinner platforms; new hardware
     support, some cleanup, etc"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
  ARM: dts: sun8i: Add dts file for inet86dz board
  ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
  ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
  ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
  ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
  ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
  ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
  ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
  ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
  ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
  ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
  ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
  ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
  ARM: dts: at91: Don't build unnecessary dtbs
  ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
  ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
  ARM: dts: at91: move isi definition to at91sam9g25ek
  ARM: dts: at91: fix i2c-gpio node name
  ARM: dts: at91: vinco: fix regulator name
  ARM: dts: at91: ariag25 : fix onewire node
  ...

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.

  A slew of changes this release cycle.  The reset driver tree, that we
  merge through arm-soc for historical reasons, is also sizable this
  time around.

  Among the changes:

   - clps711x: Treewide changes to compatible strings, merged here for simplicity.
   - Qualcomm: SCM firmware driver cleanups, move to platform driver
   - ux500: Major cleanups, removal of old mach-specific infrastructure.
   - Atmel external bus memory driver
   - Move of brcmstb platform to the rest of bcm
   - PMC driver updates for tegra, various fixes and improvements
   - Samsung platform driver updates to support 64-bit Exynos platforms
   - Reset controller cleanups moving to devm_reset_controller_register() APIs
   - Reset controller driver for Amlogic Meson
   - Reset controller driver for Hisilicon hi6220
   - ARM SCPI power domain support"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
  ARM: ux500: consolidate base platform files
  ARM: ux500: move soc_id driver to drivers/soc
  ARM: ux500: call ux500_setup_id later
  ARM: ux500: consolidate soc_device code in id.c
  ARM: ux500: remove cpu_is_u* helpers
  ARM: ux500: use CLK_OF_DECLARE()
  ARM: ux500: move l2x0 init to .init_irq
  mfd: db8500 stop passing around platform data
  ASoC: ab8500-codec: remove platform data based probe
  ARM: ux500: move ab8500_regulator_plat_data into driver
  ARM: ux500: remove unused regulator data
  soc: raspberrypi-power: add CONFIG_OF dependency
  firmware: scpi: add CONFIG_OF dependency
  video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
  input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
  pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
  serial: clps711x: Changing the compatibility string to match with the smallest supported chip
  irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
  clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
  clk: clps711x: Changing the compatibility string to match with the smallest supported chip
  ...

Pull ARM SoC defconfig updates from Olof Johansson:
 "Defconfig additions, removals, etc.

  Most of these are small changes adding the options for newly
  upstreamed drivers, or drivers needed for new board support.

  - removed Broadcom bcm_defconfig, targets are all covered in
    multi_v7_defconfig

  - new defconfig: multi_v4t_defconfig"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  ARM: multi_v7_defconfig: enable STMicroelectronics DRM Support
  ARM: multi_v7_defconfig: enable STMicroelectronics BDISP 2D blitter driver
  ARM: omap2plus_defconfig: Fix USB selection to keep Ethernet working
  ARM: configs: lpc18xx: enable adc and dac iio drivers
  ARM: config: Add a multi_v4t_defconfig
  ARM: multi_v7_defconfig: add ACT8945A
  ARM: at91/defconfig: Add ACT8945A driver
  ARM: imx_v6_v7_defconfig: Select ADS7846 support
  ARM: configs: qualcomm: Add MDM9615 missing defconfigs
  ARM: multi_v7_defconfig: Enable vivid driver as a module
  ARM: exynos_defconfig: Enable vivid driver as a module
  ARM: defconfig: enable the MSM8660 pin controller
  ARM: imx_v6_v7_defconfig: enable USB FFS gadget
  ARM: socfpga: enable PL330 DMA in socfpga_defconfig
  ARM: socfpga: add PCIe to socfpga_defconfig
  ARM: multi_v7_defconfig: defconfig: Enable r8a7792 SoC
  ARM: shmobile: defconfig: Enable r8a7792 SoC
  ARM: Remove bcm_defconfig
  ARM: multi_v7_defconfig: Enable Broadcom Kona watchdog
  ARM: multi_v7_defconfig: Enable Broadcom STB PWM
  ...

Pull 64-bit ARM SoC updates from Olof Johansson:
 "Changes to platform code for 64-bit ARM platforms.

  Nearly all of these are defconfig updates to enable new drivers or old
  drivers still used on these 64-bit platforms.

  Added platforms for this release are:

   - Broadcom BCM2837
   - Renesas R8A7796"

* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
  arm64: remove duplicate PWM entry in defconfig
  arm64: Update default configuration
  arm64: defconfig: Enable more IP blocks for Exynos7 and Exynos5433
  arm64: amlogic: select gxbb clk driver
  arm64: defconfig: Enable S2MPS11 clock and S3C RTC driver
  arm64: marvell: enable Armada 3700 clock drivers
  arm64: defconfig: enable msm8996 pinctrl support
  arm64: defconfig: Enable qcom msm8996 clk drivers
  arm: defconfig: Enable PM8941 pwr key
  arm64: defconfig: enable stmmac and realtek PHY as modules
  arm64: Kconfig: select PM{,_GENERIC_DOMAINS} for ARCH_VEXPRESS
  arm64: defconfig: enable SENSORS_ARM_SCPI
  arm64: defconfig: enable Generic on-chip SRAM driver
  arm64: configs: enable PCIe driver for Armada 7K/8K
  arm64: Add platform selection for BCM2835.
  arm64: defconfig: disable plain NEON implementation of AES
  arm64: Allow for different DMA and CPU bus offsets
  arm64: defconfig: enable Renesas R8A7796 SoC
  arm64: defconfig: Enable Cadence MACB/GEM support
  ARM64: Kconfig: Select the Amlogic Meson pin controller driver
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "Improved and new platform support for various SoCs:

  New SoC support:
   - Broadcom BCM23550
   - Freescale i.MX7Solo
   - Qualcomm MDM9615
   - Renesas r8a7792

  Improvements:
   - convert clps711x to multiplatform
   - debug uart improvements for Atmel platforms
   - Tango platform improvements: HOTPLUG_CPU, Suspend-to-ram
   - OMAP tweaks and improvements to hwmod
   - OMAP support for kexec on SMP"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
  ARM: davinci: fix build break because of undeclared dm365_evm_snd_data
  ARM: s3c64xx: smartq: Avoid sparse warnings
  ARM: sti: Implement dummy L2 cache's write_sec
  ARM: STi: Update machine _namestr to be more generic.
  arm: meson: explicitly select clk drivers
  ARM: tango: add Suspend-to-RAM support
  ARM: hisi: consolidate the hisilicon machine entries
  ARM: tango: fix CONFIG_HOTPLUG_CPU=n build
  MAINTAINERS: Update BCM281XX/BCM11XXX/BCM216XX entry
  MAINTAINERS: Update BCM63XX entry
  MAINTAINERS: Add NS2 entry
  MAINTAINERS: Fix nsp false-positives
  MAINTAINERS: Change L to M for Broadcom ARM/ARM64 SoC entries
  ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs
  ARM: clps711x: Switch to MULTIPLATFORM
  ARM: clps711x: Remove boards support
  ARM: clps711x: Add basic DT support
  ARM: clps711x: Reduce static map size
  ARM: SAMSUNG: Constify iomem address passed to s5p_init_cpu
  ARM: oxnas: Change OX810SE default driver config
  ...

Pull ARM SoC cleanups from Olof Johansson:
 "The cleanup branch keeps going down in size as we've completed a lot
  of the major legacy platform removals and conversions.

  A handful of changes this time around, some of the themes or larger
  sets are:

   - A bunch of i.MX cleanups around platform detection, init call cleanups
   - Misc fixes of missing/implicit includes
   - Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
  ARM: mps2: fix typo
  ARM: s3c64xx: avoid warning about 'struct device_node'
  bus: mvebu-mbus: make mvebu_mbus_syscore_ops static
  bus: mvebu-mbus: fix __iomem on register pointers
  ARM: tegra: Remove board_init_funcs array
  ARM: iop: Fix indentation
  ARM: imx: remove cpu_is_mx*()
  ARM: imx: remove last call to cpu_is_mx5*
  ARM: imx: rework mx27_pm_init() call
  ARM: imx: deconstruct mx3_idle
  ARM: imx: deconstruct mxc_rnga initialization
  ARM: imx: remove cpu_is_mx1 check
  ARM: i.MX: Do not explicitly call l2x0_of_init()
  ARM: i.MX: system.c: Tweak prefetch settings for performance
  ARM: i.MX: system.c: Replace magic numbers
  ARM: i.MX: system.c: Remove redundant errata 752271 code
  ARM: i.MX: system.c: Convert goto to if statement
  ARM: Kirkwood: fix kirkwood_pm_init() declaration/type
  ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static
  ARM: orion5x: make orion5x_legacy_handle_irq static
  ...

Merge tag 'linux-kselftest-4.8-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest updates from Shuah Khan:
 "This contains new tests and fixes:

   - a few fixes to existing tests

   - new media tests for testing driver unbind, and device removal paths
     while an user application is actively making system calls and
     ioctls"

* tag 'linux-kselftest-4.8-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: media_tests add a new video device test
  selftests: media_tests - Add media_device_open to .gitignore
  selftests: add media controller regression test scripts and document
  selftests: add media_device_open test
  selftests: media_device_test change it to randomize loop count
  selftests/vm: Don't mlockall MCL_CURRENT in on-fault-limit test
  selftests/vm: write strlen length instead of sizeof to nr_hugepages
  selftests/lib: set printf.sh executable

Merge tag 'linux-kselftest-4.8-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fixes from Shuah Khan:

 - Add a new timer set-tz test case

 - Fix a bug in exec test Makefile dependency list

* tag 'linux-kselftest-4.8-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/exec: Makefile is a run-time dependency, add it to the install list
  kselftests: timers: Add set-tz test case

Merge tag 'hwmon-for-linus-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull more hwmon updates from Guenter Roeck:

 - Improved error handling in tmp102, lm75, and lm90 drivers

 - Bug fixes in sht3x, ftsteutates, iio_hwmon, and adt7411 drivers

* tag 'hwmon-for-linus-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (adt7411) set sane values for CFG1 and CFG3
  hwmon: (iio_hwmon) fix memory leak in name attribute
  hwmon: (ftsteutates) Fix potential memory access error
  hwmon: (tmp102) Improve error handling
  hwmon: (lm75) Improve error handling
  hwmon: (lm90) Improve error handling
  hwmon: (lm90) Add missing assignment
  hwmon: (sht3x) set initial jiffies to last_update

Pull crypto fixes from Herbert Xu:
 "This fixes a number of regressions in the marvell cesa driver caused
  by the chaining work, and a regression in lib/mpi that leads to a
  GFP_KERNEL allocation with preemption disabled"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: marvell - Don't copy IV vectors from the _process op for ciphers
  lib/mpi: Fix SG miter leak
  crypto: marvell - Update cache with input sg only when it is unmapped
  crypto: marvell - Don't chain at DMA level when backlog is disabled
  crypto: marvell - Fix memory leaks in TDMA chain for cipher requests

Pull x86 header cleanups from Ingo Molnar:
 "This tree is a cleanup of the x86 tree reducing spurious uses of
  module.h - which should improve build performance a bit"

* 'x86-headers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, crypto: Restore MODULE_LICENSE() to glue_helper.c so it loads
  x86/apic: Remove duplicated include from probe_64.c
  x86/ce4100: Remove duplicated include from ce4100.c
  x86/headers: Include spinlock_types.h in x8664_ksyms_64.c for missing spinlock_t
  x86/platform: Delete extraneous MODULE_* tags fromm ts5500
  x86: Audit and remove any remaining unnecessary uses of module.h
  x86/kvm: Audit and remove any unnecessary uses of module.h
  x86/xen: Audit and remove any unnecessary uses of module.h
  x86/platform: Audit and remove any unnecessary uses of module.h
  x86/lib: Audit and remove any unnecessary uses of module.h
  x86/kernel: Audit and remove any unnecessary uses of module.h
  x86/mm: Audit and remove any unnecessary uses of module.h
  x86: Don't use module.h just for AUTHOR / LICENSE tags

Pull backlight updates from Lee Jones:
 "Add support for an enable regulator to lp855x_bl"

* tag 'backlight-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: lp855x: Add enable regulator

Pull MFD updates from Lee Jones:
 "Core Framework:
   - New API to call bespoke pre/post IRQ handlers; Regmap

  New Device Support:
   - Add support for RN5T567 to rn5t618
   - Add support for COMe-cSL6 and COMe-mAL10 to kempld-core

  New Functionality:
   - Add support for USB Power Supply to axp20x
   - Add support for Power Key to hi655x-pmic

  Fix-ups:
   - Update MAINTAINERS; Dialog, Altera
   - Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
   - Add module support; max14577
   - Constifying; max77620
   - Allow bespoke IRQ masking/unmasking; max77620
   - Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
   - Power Management fixups; arizona-core
   - Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
   - Clocking fixups; twl6040
   - Trivial (spelling, headers, coding-style, whitespace, (re)naming);
       si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic

  Bug Fixes:
   - Fix offset error for MSM8660; qcom_rpm
   - Fix possible spurious IRQs; arizona, hi655x-pmic"

* tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
  mfd: qcom_rpm: Parametrize also ack selector size
  mfd: twl6040: Handle mclk used for HPPLL and optional internal clock source
  mfd: Add support for COMe-cSL6 and COMe-mAL10 to Kontron PLD driver
  mfd: hi655x: Fix return value check in hi655x_pmic_probe()
  mfd: smsc-ece1099: Return directly after a function failure in smsc_i2c_probe()
  mfd: smsc-ece1099: Delete an unnecessary variable initialisation in smsc_i2c_probe()
  mfd: dm355evm_msp: Return directly after a failed platform_device_alloc() in add_child()
  mfd: twl-core: Refactoring for add_numbered_child()
  mfd: twl-core: Return directly after a failed platform_device_alloc() in add_numbered_child()
  mfd: arizona: Add missing disable of PM runtime on probe error path
  mfd: stmpe: Move platform data into MFD driver
  mfd: max14577: Allow driver to be built as a module
  mfd: max14577: Use module_init() instead of subsys_initcall()
  mfd: arizona: Remove some duplicate defines
  mfd: qcom_rpm: Remove unused define
  mfd: hi655x-pmic: Add powerkey device to hi655x PMIC driver
  mfd: hi655x-pmic: Rename some interrupt macro names
  mfd: hi655x-pmic: Fixup issue with un-acked interrupts
  mfd: arizona: Check if AOD interrupts are pending before dispatching
  mfd: qcom_rpm: Fix offset error for msm8660
  ...

Pull IOMMU updates from Joerg Roedel:

 - big-endian support and preparation for defered probing for the Exynos
   IOMMU driver

 - simplifications in iommu-group id handling

 - support for Mediatek generation one IOMMU hardware

 - conversion of the AMD IOMMU driver to use the generic IOVA allocator.
   This driver now also benefits from the recent scalability
   improvements in the IOVA code.

 - preparations to use generic DMA mapping code in the Rockchip IOMMU
   driver

 - device tree adaption and conversion to use generic page-table code
   for the MSM IOMMU driver

 - an iova_to_phys optimization in the ARM-SMMU driver to greatly
   improve page-table teardown performance with VFIO

 - various other small fixes and conversions

* tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits)
  iommu/amd: Initialize dma-ops domains with 3-level page-table
  iommu/amd: Update Alias-DTE in update_device_table()
  iommu/vt-d: Return error code in domain_context_mapping_one()
  iommu/amd: Use container_of to get dma_ops_domain
  iommu/amd: Flush iova queue before releasing dma_ops_domain
  iommu/amd: Handle IOMMU_DOMAIN_DMA in ops->domain_free call-back
  iommu/amd: Use dev_data->domain in get_domain()
  iommu/amd: Optimize map_sg and unmap_sg
  iommu/amd: Introduce dir2prot() helper
  iommu/amd: Implement timeout to flush unmap queues
  iommu/amd: Implement flush queue
  iommu/amd: Allow NULL pointer parameter for domain_flush_complete()
  iommu/amd: Set up data structures for flush queue
  iommu/amd: Remove align-parameter from __map_single()
  iommu/amd: Remove other remains of old address allocator
  iommu/amd: Make use of the generic IOVA allocator
  iommu/amd: Remove special mapping code for dma_ops path
  iommu/amd: Pass gfp-flags to iommu_map_page()
  iommu/amd: Implement apply_dm_region call-back
  iommu/amd: Create a list of reserved iova addresses
  ...

Pull mailbox updates from Jussi Brar:
 "Broadcom:
   - New PDC controller driver and bindings

  Misc:
   - PL320 - Convert from 'raw' IO to 'relaxed' version
   - Test - fix dangling pointer"

* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: Fix format and type mismatches in Broadcom PDC driver
  mailbox: Add Broadcom PDC mailbox driver
  dt-bindings: add bindings documentation for PDC driver.
  mailbox: pl320: remove __raw IO
  mailbox: mailbox-test: set tdev->signal to NULL after freeing

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - A couple of changes to improve the support for erase/discard/trim cmds
   - Add eMMC HS400 enhanced strobe support
   - Show OCR and DSR registers in SYSFS for MMC/SD cards
   - Correct and improve busy detection logic for MMC switch (CMD6) cmds
   - Disable HPI cmds for certain broken Hynix eMMC cards
   - Allow MMC hosts to specify non-support for SD and MMC cmds
   - Some minor additional fixes

  MMC host:
   - sdhci: Re-works, fixes and clean-ups
   - sdhci: Add HW auto re-tuning support
   - sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
   - sdhci-esdhc-imx: Fixes and clean-ups
   - sdhci-esdhc-imx: Update system PM support
   - sdhci-esdhc-imx: Enable HW auto re-tuning
   - sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
   - sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
   - sdhci-msm: Add support for UHS cards
   - sdhci-tegra: Improve support for UHS cards
   - sdhci-of-arasan: Update phy support for Rockchip SoCs
   - sdhci-of-arasan: Deploy enhanced strobe support
   - dw_mmc: Some fixes and clean-ups
   - dw_mmc: Enable support for erase/discard/trim cmds
   - dw_mmc: Enable CMD23 support
   - mediatek: Some fixes related to the eMMC HS400 support
   - sh_mmcif: Improve support for HW busy detection
   - rtsx_pci: Enable support for erase/discard/trim cmds"

* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
  mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
  mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
  mmc: rtsx_pci: Use the provided busy timeout from the mmc core
  mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
  mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
  mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
  mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
  mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
  mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
  mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
  mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
  mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
  mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
  mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
  mmc: Change the max discard sectors and erase response when HW busy detect
  phy: rockchip-emmc: Wait even longer for the DLL to lock
  phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
  mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
  mmc: sdhci-msm: Add support for UHS cards
  mmc: sdhci-msm: Add set_uhs_signaling() implementation
  ...

Pull watchdog updates from Wim Van Sebroeck:
 "Core:
   - min and max timeout improvements, WDOG_HW_RUNNING improvements,
     status funtionality
   - Add a device managed API for watchdog_register_device()

  New watchdog drivers:
   -  Aspeed SoCs
   -  Maxim PMIC MAX77620
   -  Amlogic Meson GXBB SoC

  Enhancements:
   - support for the r8a7796 watchdog device
   - support for F81866 watchdog device
   - support for 5th variation of Apollo Lake
   - support for MCP78S chipset
   - clean-up of softdog.c watchdog device driver
   - pic32-wdt and pic32-dmt fixes
   - Documentation/watchdog: watchdog-test improvements
   - several other fixes and improvements"

* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
  watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
  watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
  watchdog: core: Fix error handling of watchdog_dev_init()
  watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
  watchdog: pic32-dmt: Remove .owner field for driver
  watchdog: pic32-wdt: Remove .owner field for driver
  watchdog: renesas-wdt: Add support for the r8a7796 wdt
  Documentation/watchdog: check return value for magic close
  watchdog: sbsa: Drop status function
  watchdog: Implement status function in watchdog core
  watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
  watchdog: change watchdog_need_worker logic
  watchdog: add support for MCP78S chipset in nv_tco
  watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
  watchdog: bcm2835_wdt: constify _ops and _info structures
  dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
  watchdog: Add Meson GXBB Watchdog Driver
  watchdog: qcom: configure BARK time in addition to BITE time
  watchdog: qcom: add option for standalone watchdog not in timer block
  watchdog: qcom: update device tree bindings
  ...

Pull btrfs updates from Chris Mason:
 "This pull is dedicated to Josef's enospc rework, which we've been
  testing for a few releases now.  It fixes some early enospc problems
  and is dramatically faster.

  This also includes an updated fix for the delalloc accounting that
  happens after a fault in copy_from_user.  My patch in v4.7 was almost
  but not quite enough"

* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix delalloc accounting after copy_from_user faults
  Btrfs: avoid deadlocks during reservations in btrfs_truncate_block
  Btrfs: use FLUSH_LIMIT for relocation in reserve_metadata_bytes
  Btrfs: fill relocation block rsv after allocation
  Btrfs: always use trans->block_rsv for orphans
  Btrfs: change how we calculate the global block rsv
  Btrfs: use root when checking need_async_flush
  Btrfs: don't bother kicking async if there's nothing to reclaim
  Btrfs: fix release reserved extents trace points
  Btrfs: add fsid to some tracepoints
  Btrfs: add tracepoints for flush events
  Btrfs: fix delalloc reservation amount tracepoint
  Btrfs: trace pinned extents
  Btrfs: introduce ticketed enospc infrastructure
  Btrfs: add tracepoint for adding block groups
  Btrfs: warn_on for unaccounted spaces
  Btrfs: change delayed reservation fallback behavior
  Btrfs: always reserve metadata for delalloc extents
  Btrfs: fix callers of btrfs_block_rsv_migrate
  Btrfs: add bytes_readonly to the spaceinfo at once

According to the datasheet we have to set some bits as 0 and others as 1.
Make sure we do this for CFG1 and CFG3.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The "name" variable's memory is now freed when the device is destructed
thanks to devm function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: e0f8a24e ("staging:iio::hwmon interface client driver.")
Fixes: 61bb53bc ("hwmon: (iio_hwmon) Add support for humidity sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Using set_bit() to set a bit in an integer is not a good idea, since
the function expects an unsigned long as argument, which can be 64 bit
wide. Coverity reports this problem as

>>>     CID 1364488:  Memory - illegal accesses  (INCOMPATIBLE_CAST)
>>>     Pointer "&ret" points to an object whose effective type is "int"
>>>	(32 bits, signed) but is dereferenced as a wider "unsigned
+long" (64 bits, unsigned).  This may lead to memory corruption.
245                     set_bit(1, (unsigned long *)&ret);

Just use BIT instead.

Cc: Thilo Cestonaro <thilo@cestona.ro>
Fixes: 08426eda ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>