Merge tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: third (and last) batch of dts updates for 3.20" from
Heiko Stübner:

Change are regulator nodes for the cpu and gpu regulators on the act8846
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.

* tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
  ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
  ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
  ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
  ARM: dts: rockchip: add rk3288 watchdog clock
  clk: rockchip: add id for watchdog pclk on rk3288
  clk: rockchip: add clock IDs for the PVTM clocks
  clk: rockchip: add clock ID for usbphy480m_src
Signed-off-by: Olof Johansson <olof@lixom.net>

Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.

Therefore this is a property of the board and should be specified there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This enables the recently added display nodes on the firefly and evb,
letting the boards output graphic data over the hdmi port.

This includes enabling of i2c5 on the evb that is used for ddc probing and
setting the lcd-regulators to always on until the hdmi driver learns
about using them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Use the same transfer speed on both the rk808 and act8846 variants and
remove the status=okay from the rk808 one which is already set in the
shared rk3288-evb.dtsi .
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The evaluation board using the act8846 as main pmic uses two additional
regulators to provide the cpu and gpu voltage. Add these and also add
the link to cpu supply from vdd_cpu.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Merge "Zync DT for v3.20" from Michal Simek:

arm: Xilinx Zynq dt patches for v3.20

- Add USB chipidea driver to DT
- Add pincontrol
- Add aliases node
- Fix WDT node

* tag 'zynq-dt-for-3.20' of https://github.com/Xilinx/linux-xlnx:
  ARM: zynq: DT: Add aliases node
  ARM: zynq: DT: Fix binding for cadence WDT
  ARM: zynq: DT: Add pinctrl information to USB nodes
  ARM: zynq: DT: Remove bogus value from 'bias-disable' property
  ARM: zynq: DT: Add pinctrl information
  ARM: zynq: DT: Add USB to device tree
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:

- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
  and the power domain node including FIMD1, MIXER and HDMI modules
  (tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
  and exynos5422 Odroid XU3 by Javier Martinez Canillas)

Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.

* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Add DISP1 power domain for exynos5420
  clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Merge "Samsung 2nd DT updates for v3.20" from Kukjin Kim:

- for all of Samsung SoCs
  : use generic power domain bindings
  : add 'dr_mode' property for hsotg/dwc2 devices

- exynos3250-rinato and exynos3250-monk
  : add regulator-haptic

- exynos5422-odroidxu3
  : reduce total RAM by 22 MiB because last 22 MiB
    for secure monitor cannot be accessed by kernel
  : add on-board INA231 sensors and LDO26 of PMIC
    for the sensors

* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
  ARM: dts: add on-board INA231 sensors for exynos5422-odroidxu3
  ARM: dts: Add regulator-haptic node for exynos3250-monk
  ARM: dts: Add regulator-haptic node for exynos3250-rinato
  ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
  ARM: dts: convert to generic power domain bindings for exynos DT
Signed-off-by: Olof Johansson <olof@lixom.net>

cx92755.dtsi describes CX92755 on chip peripherals. cx92755_equinox.dts
describes the Equinox evaluation board for the CX92755 SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>

The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.

When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

When a power domain is powered off on Exynos5420 SoC, the input clocks of
the devices attached to this power domain are re-parented to oscclk and
restored to the original parent after powering on the power domain.

So a reference to the input and parent clocks for the devices attached to
a power domain are needed to be able to do the re-parenting. The DISP1 pd
includes modules which uses the following clocks:

ACLK_200_DISP1 (MIXER and HDMILINK)
ACLK_300_DISP1 (FIMD1)
ACLK_400_DISP1 (Internal Buses)

Each of these clocks are generated as the output of a clock mux so add an
ID for all of these clock muxes and their parents to be referenced in the
DISP1 power domain device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

Add aliases node to DTs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Based on:
"devicetree: Add Cadence WDT devicetree bindings documentation"
(sha1: 191891c0)

- compatible string is cdns,wdt-r1p2
- remove device_type property
- remove int reset property (reset-on-timeout is bool)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: arm-soc
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

In one pinctrl node, a 'bias-disable' property is erroneously assigned a
value.

Fixes: ARM: zynq: DT: Add pinctrl information
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add the clock property for the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>

Merge tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: second batch of dts updates for 3.20" from Heiko Stübner:

Basic display nodes for crtcs and hdmi encoder, timer node
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).

* tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
  ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
  dt-bindings: add vendor prefix and root compatible property for Rockchip boards
  ARM: dts: rockchip: Add rockchip timer node for rk3288
  ARM: dts: rockchip: add rk3288 hdmi nodes
  ARM: dts: rockchip: Add rk3288 vop and display-subsystem
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds a devicetree binding documentation for FSL's
Management Complex.

Management Complex is a hardware resource manager that manages
specialized hardware objects used in network-oriented packet
processing applications
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds a devicetree binding documentation for FSL's
LS2085A SoC and Simulator model.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch addss the device-tree documentation for Freescale's
NS16550 UART (also called DUART).

There is a specific errata fix required in FSL NS16550 UART
which ensures that an random interrupt storm is not observed when
a break is provided as an input to the UART.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Of the Digicolor SoCs series only CX92755 is currently supported.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt

Merge "at91: dt for 3.20 #2" from Nicolas Ferre:

Second DT batch for 3.20:
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97

* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: sam9263: Add ac97 device node
  dt: atmel_ac97c: Add device tree documentation
  ARM: at91: at91sam9n12ek/dt: use dt ids for wm8904
  ARM: at91: sama5d3xek/dt: use dt ids for wm8904
  ARM: at91: sama5d4: dts: change the nand compatible string
  ARM: at91/dt: sama5d4: add pioD controller
  ARM: at91/dt: disable pull-up on vbus-gpio (PB16) to reduce power consumption
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Merge "Allwinner device tree changes for 3.20" from Maxime Ripard:

A lot of changes to the device tree for the 3.20 merge window, mostly with:
  - More DT license convertions, only two DTS and two DTSI are still uncertain
    and have not been converted yet
  - Use the C-preprocessor includes in the device trees.
  - Add support for the A31s SoC and improve the A80 support
  - Add IR receiver, lradc, PS/2 support
  - Add cpufreq support for all SoCs but the A23 and A80.
  - And a lot of new boards

* tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (64 commits)
  ARM: dts: sun5i: Enable axp209 support on A13-OLinuxIno
  ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
  ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
  ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
  ARM: dts: sun4i: Add Hyundau A7HD board
  ARM: dts: sun4i: Add Marsboard A10 board
  ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
  ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
  ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
  ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
  ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
  ARM: dts: sun9i: Add mmc config clock nodes
  ARM: dts: sunxi: Add missing mdio label
  ARM: dts: sun5i: Add mk802_a10s board
  ARM: dts: sun4i: Add mk802ii board
  ARM: dts: sun4i: Add mk802 board
  ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
  ARM: dts: sun7i: Add dts file for Bananapro board
  ARM: sun6i: Enable ARM arch timers
  ARM: dts: sun6i: Convert hummingbird a31 dts to label references
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Merge "Samsung DT updates for v3.20" from Kukjin Kim:

- exynos3250
  : add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
  : enable usb
  : cleanup and use macro for gpio-keys
  : add fimd and Panel devices support
- exynos3250-monk
  : enable usb
  : cleanup and use macro for gpio-keys
- exynos5250-snow
  : add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
  : configure regulators for suspend
  : set always on for USB webCam regulators
  : add lid GPIO key device
- exynos5422
  : add support new board Odroid XU3
- dt-bindings
  : add exynos-chipid

* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Configure regulators for suspend on exynos Peach boards
  ARM: dts: Set Peach boards USB WebCam regulators to always on
  ARM: dts: Add lid GPIO key device node for Peach boards
  ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
  Documentation: dt-bindings: add exynos-chipid binding information
  ARM: dts: add Panel device support for exynos3250-rinato
  ARM: dts: add fimd device support for exynos3250-rinato
  ARM: dts: use macro in gpio keys for exynos3250 boards
  ARM: dts: remove unnecessary gpio-key nodes for exynos3250 boards
  ARM: dts: Enable USB node for exynos3250-monk
  ARM: dts: Enable USB node for exynos3250-rinato
  ARM: dts: Add hsotg node for exynos3250
  ARM: dts: Add exynos_usbphy node for exynos3250
  ARM: dts: Add dts file for Odroid XU3 board
Signed-off-by: Olof Johansson <olof@lixom.net>

The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config
options may be removed in the near future.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This adds the device node for the ac97 controller.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-By Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This adds the bindings for AC97 controller device tree support.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-By Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Using the device tree ids for wm8904 codec.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Using the wm8904 device tree compatible string.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

As we introduce a new "atmel,sama5d4-nand" compatible string for sama5d4,
so we need to apply it for sama5d4 chip.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This add support for Rayeager PX2, Rockchip PX2 based development board
made by ChipSPARK.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds support for Firefly-RK3288, Rockchip RK3288 based development
boards made by Firefly.

There are 2 dts for 2 versions of the board. rk3288-firefly-beta.dts is
for the beta version, rk3288-firefly.dts is for the mass production version.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>

[removed gmac reference, due to the gmac node going through the net-tree]
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds vendor prefix and root compatible property for following boards

- Firefly, Firefly-RK3288 boards (both beta and mass production version)
- ChipSPARK, Rayeager PX2 board

PX2 SoC is fully compatible with RK3066.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The rk3288 board uses the architected timers and these ones are shutdown when
the cpu is powered down. There is a need of a broadcast timer in this case to
ensure proper wakeup when the cpus are in sleep mode and a timer expires.

Add the timer node for the broadcast timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The (non micro) A13-OLinuxIno has an axp203 pmic, enable support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we support the sun6i variant of the touchscreen controller,
add the device node to the dtsi so we can use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Last 22 MiB is RAM is reserved by secure monitor code and cannot be
accessed from Linux kernel, so adjust total RAM size to 0x7EA00000
(2 GiB - 22 MiB). This fixes random 'imprecise kernel abort' kernel
failures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>