- 25 Jul, 2016 38 commits
-
-
Jaehoon Chung authored
In linux/mmc/host.h, mmc_card_is_removable() is already defined. It should be maintainted more easier than now. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Douglas Anderson authored
The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by:Douglas Anderson <dianders@chromium.org> Acked-by:
Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Douglas Anderson authored
There's no reason to store the return value of rockchip_emmc_phy_power() in a variable nor to check it. Just return it. Signed-off-by:
-
Douglas Anderson authored
As of an earlier change in this series ("Documentation: mmc: sdhci-of-arasan: Add ability to export card clock") the SDHCI driver used on Rockchip SoCs can now expose its clock. Let's now specify that the PHY can use it. Letting the PHY get access to this clock means it can adjust phyctrl_frqsel field appropriately. Although the Rockchip PHY appears slightly different than the reference Arasan one, you can see that the Arasan datasheet [1] had it defined as: Select the frequency range of DLL operation: 3b'000 => 200MHz to 170 MHz 3b'001 => 170MHz to 140 MHz 3b'010 => 140MHz to 110 MHz 3b'011 => 110MHz to 80MHz 3b'100 => 80MHz to 50 MHz 3b'101 => 275Mhz to 250MHz 3b'110 => 250MHz to 225MHz 3b'111 => 225MHz to 200MHz On the Rockchip version of the PHY we have less granularity but the idea is the same. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by:Rob Herring <robh@kernel.org> Reviewed-by:
-
Douglas Anderson authored
Some SD/eMMC PHYs (like the PHY from Arasan that is designed to work with arasan,sdhci-5.1) need to know the card clock in order to function properly. Let's add the ability to expose this clock. Any PHY that needs to know the clock rate can add a reference and query the clock rate. At the moment we register a CLK_GET_RATE_NOCACHE clock that simply allows querying the clock. This allows us to be less intrusive with regards to the main SDHCI driver, which has complex logic for adjusting the SD clock. Right now we always fully power cycle the PHY when the clock changes and that gives the PHY a good chance to query our clock. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Douglas Anderson authored
Some SD/eMMC PHYs (like the PHY from Arasan that is designed to work with arasan,sdhci-5.1) need to know the card clock frequency in order to function properly. Physically in a SoC this clock is exported from the SDHCI IP block to the PHY IP block and the PHY needs to know the speed. Let's export the SDHCI card clock using a standard device tree mechanism so that the PHY can get access to it and query the card clock frequency. Signed-off-by:
-
Douglas Anderson authored
In the the earlier change in this series ("Documentation: mmc: sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the mechansim for specifying a syscon to properly set corecfg registers in sdhci-of-arasan. Now let's use this mechanism to properly set corecfg_baseclkfreq on rk3399. >From [1] the corecfg_baseclkfreq is supposed to be set to: Base Clock Frequency for SD Clock. This is the frequency of the xin_clk. This is a relatively easy thing to do. Note that we assume that xin_clk is not dynamic and we can check the clock at probe time. If any real devices have a dynamic xin_clk future patches could register for notifiers for the clock. At the moment, setting corecfg_baseclkfreq is only supported for rk3399 since we need a specific map for each implementation. The code is written in a generic way that should make this easy to extend to other SoCs. Note that a specific compatible string for rk3399 is already in use and so we add that to the table to match rk3399. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by: -
Douglas Anderson authored
As can be seen in Arasan's datasheet [1] there are several "corecfg" settings in their SDHCI IP Block that are supposed to be controlled by software. Although the datasheet referenced is a bit vague about how to access corecfg, in Figure 5 you can see that for Arasan's PHY (a separate component than their SDHCI component) they describe the "phyctrl" registers as being "FROM SOC CTL REG", implying that it's up to the licensee of the Arasan IP block to implement these registers. It seems sane to assume that the "corecfg" registers in their SDHCI IP block works in a similar way for all licensees of the IP Block. Device tree has a model that allows a device to get a reference to random registers located elsewhere in the SoC: sysctl. Let's leverage this model and allow adding a sysctl reference to access the control registers for the Arasan SDHCI PHYs. Having a reference to the control registers doesn't do much for us on its own since the Arasan spec doesn't specify how these corecfg values are laid out in memory. In the SDHCI driver we'll need a map detailing where each corecfg can be found in each implementation. This map can be found using the primary compatible string of the SDHCI device. In that spirit, document that existing rk3399 device trees already have a specific compatible string, though up to now they've always been relying on the driver supporting the generic. Note that since existing devices seem to work fairly well as-is, we'll list the syscon reference as "optional", but it's likely that we'll run into much fewer problems if we can actually set the proper values in the syscon, so it is strongly suggested that any SoCs where we have a map to set the corecfg also include a reference to the syscon. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdfSigned-off-by:
-
Douglas Anderson authored
In commit 802ac39a ("mmc: sdhci-of-arasan: fix set_clock when a phy is supported") we added code to power the PHY off and on whenever the clock was changed but we avoided doing the power cycle code when the clock was low speed. Let's now do it always. Although there may be other reasons for power cycling the PHY when the clock changes, one of the main reasons is that we need to give the DLL a chance to re-lock with the new clock. One of the things that the DLL is for is tuning the Receive Clock in HS200 mode and STRB in HS400 mode. Thus it is clear that we should make sure we power cycle the PHY (and wait for the DLL to lock) when we know we'll be in one of these two speed modes. That's what the original code did, though it used the clock rate rather than the speed mode. However, even in speed modes other than HS200,/HS400 the DLL is used for something since it can be clearly observed that the PHY doesn't function properly if you leave the DLL off. Although it appears less important to power cycle the PHY and wait for the DLL to lock when not in HS200/HS400 modes (no bugs were reported), it still seems wise to let the locking always happen nevertheless. Note: as part of this, we make sure that we never try to turn the PHY on when the clock is off (when the clock rate is 0). The PHY cannot work when the clock is off since its DLL can't lock. This change requires ("phy: rockchip-emmc: Increase lock time allowance") and will cause problems if picked without that change. Signed-off-by:
-
Douglas Anderson authored
Previous PHY code waited a fixed amount of time for the DLL to lock at power on time. Unfortunately, the time for the DLL to lock is actually a bit more dynamic and can be longer if the card clock is slower. Instead of waiting a fixed 30 us, let's now dynamically wait until the lock bit gets set. We'll wait up to 10 ms which should be OK even if the card clock is at the super slow 100 kHz. On its own, this change makes the PHY power on code a little more robust. Before this change the PHY was relying on the eMMC code to make sure the PHY was only powered on when the card clock was set to at least 50 MHz before, though this reliance wasn't documented anywhere. This change will be even more useful in future changes where we actually need to be able to wait for a DLL lock at slower clock speeds. Signed-off-by:
-
Brian Norris authored
Some of the spacing was wrong (spaces instead of tabs), and due to longer entries added later, the columns weren't aligned. Let's get everything consistent. Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
Brian Norris authored
The output tap delay controls helps maintain the hold requirements for eMMC. The exact value is dependent on the SoC and other factors, though it isn't really an exact science. But the default of 0 is not very good, as it doesn't give the eMMC much hold time, so let's bump up to 4 (approx 90 degree phase?). If we need to configure this any further (e.g., based on board or speed factors), we may need to consider a device tree representation. Suggested-by:
-
Shawn Lin authored
Signal integrity analysis has suggested we set these values. Do this in power_on(), so that they get reconfigured after suspend/resume. Signed-off-by:
-
Shawn Lin authored
According to the databook, 10.2us is the max time for dll to be ready to work. However in testing, some chips need 20us for dll to be ready. This patch adds some extra margin for dllrdy to be ready, fixing our -ETIMEDOUT issues. Signed-off-by:
-
Al Cooper authored
Add SDHCI driver for Broadcom BRCMSTB SoCs. This driver works with all ARM based SoCs and the 7425, 7429 and 7435 MIPS based SoCs. The driver disables all UHS speed modes by default and relies on the Device Tree node properties to enable these modes for SoC/Board combinations that support them. Signed-off-by:
Al Cooper <alcooperx@gmail.com> Acked-by:
-
Al Cooper authored
The example includes the properties required to enable UHS modes. Signed-off-by:
-
Adrian Hunter authored
Apparently a cut-and-paste error, 'do_data_tag' is using 'brq' for data size even though 'brq' has not been set up. Instead use blk_rq_sectors(). Signed-off-by:
-
Pratibhasagar V authored
Certain Hynix eMMC 4.41 cards might get broken when HPI feature is used and hence this patch disables the HPI feature for such buggy cards. As some of the other features like BKOPs/Cache/Sanitize are dependent on HPI feature, those features would also get disabled if HPI is disabled. Signed-off-by:
Pratibhasagar V <pratibha@codeaurora.org> Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> [gdavis: Forward port and cleanup] Signed-off-by:
George G. Davis <george_davis@mentor.com> Signed-off-by:
-
Peter Griffin authored
mmc_select_bus_width() returns bus width (4 or 8) on success or zero if unsupported. So only change mode if setting the bus width is successful. Signed-off-by:
Peter Griffin <peter.griffin@linaro.org> Signed-off-by:
-
Gwendal Grignou authored
If available, eMMC stack uses HC_ERASE_GRP_SIZE as the preferred erase size. As some high capacity eMMC (64MB) reports this size to 512kB, the discard operations end up taking very long time. Improve the behaviour by instead calculating the preferred erase size based on the eMMC size. In this way the discard operations becomes faster. Signed-off-by:
Gwendal Grignou <gwendal@chromium.org> [Ulf: Updated changelog and improved comment in code] Signed-off-by:
-
Stefan Wahren authored
The sdhci-bcm2835 is no more needed since it has been replaced by sdhci-iproc. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Eric Anholt <eric@anholt.net> Signed-off-by:
-
Stefan Wahren authored
The sdhci-iproc also supports bcm2835. So this binding is obsolete. Signed-off-by:
Stephen Warren <swarren@wwwdotorg.org> Signed-off-by:
-
Ziyuan Xu authored
To slove the issue which was found on gru board for hs400. [ 4.616946] sdhci: Secure Digital Host Controller Interface driver [ 4.623135] sdhci: Copyright(c) Pierre Ossman [ 4.722575] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.730962] sdhci-arasan fe330000.sdhci: No vmmc regulator found [ 4.737444] sdhci-arasan fe330000.sdhci: No vqmmc regulator found [ 4.774930] mmc0: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA [ 4.980295] mmc0: switch to high-speed from hs200 failed, err:-84 [ 4.986487] mmc0: error -84 whilst initialising MMC card We should change HS400 mode selection timing to meet JEDEC specification. The JEDEC 5.1 said that change the frequency to <= 52MHZ after HS_TIMING switch. Refer to section 6.6.2.3 "HS400" timing mode selection: Set the "Timing Interface" parameter in the HS_TIMING[185] field of the Extended CSD register to 0x1 to switch to High Speed mode and then set the clock frequency to a value not greater than 52MHZ. Signed-off-by:
Ziyuan Xu <xzy.xu@rock-chips.com> Signed-off-by:
-
Chaotian Jing authored
with CONFIG_HZ=100, the precision of jiffies is 10ms, and the generic_cmd6_time of some card is also 10ms. then, may be current time is only 5ms, but already timed out caused by jiffies precision. Signed-off-by:
Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by:
-
Chaotian Jing authored
Per JEDEC spec, it is not recommended to use CMD13 to get card status after speed mode switch. below are two reason about this: 1. CMD13 cannot be guaranteed due to the asynchronous operation. Therefore it is not recommended to use CMD13 to check busy completion of the timing change indication. 2. After switch to HS200, CMD13 will get response of 0x800, and even the busy signal gets de-asserted, the response of CMD13 is aslo 0x800. Signed-off-by:
-
Chaotian Jing authored
Some MMC hosts do not support MMC_CAP_WAIT_WHILE_BUSY, but implements the ->card_busy() callback. In such cases, extend __mmc_switch() to use this method to check card status after switch command. Signed-off-by:
-
Adrian Hunter authored
host->card_busy() was introduced for SD voltage switching which checks all 4 data lines. Increasingly, host->card_busy is being used to poll the the busy signal which is only data line 0 (DAT[0]). The current logic in sdhci_card_busy() does not work in that case because it returns false if any of the data lines is high. It also ignores possibilities: - data lines 1-3 are not connected and could show at any level - data lines 1-2 can be used by SDIO for other purposes According to the SD specification, it is OK to check any of the data lines for voltage switching, so change to use DAT[0] only. Signed-off-by:
-
Wolfram Sang authored
Sparse complains about the implicit cast. Making it explicit is indeed better coding style. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Shawn Lin authored
Currently sdhci-arasan 5.1 can support enhanced strobe function, and we now limit it just for "arasan,sdhci-5.1". Add mmc-hs400-enhanced-strobe in DT to enable the function if we're sure our controller can support it. Signed-off-by:
-
Shawn Lin authored
We introduce HS400 with enhanced strobe function, so we need to add it for debug show. Signed-off-by:
-
Shawn Lin authored
Controllers use data strobe line to latch data from devices under hs400 mode, but not for cmd line. So since emmc 5.1, JEDEC introduces enhanced strobe mode for latching cmd response from emmc devices to host controllers. This new feature is optional, so it depends both on device's cap and host's cap to decide whether to use it or not. Signed-off-by:
-
Shawn Lin authored
This patch introduce mmc-hs400-enhanced-strobe for platforms which want to enable enhanced strobe function from DT if the mmc host controller claims to support enhanced strobe. Signed-off-by:
-
Shawn Lin authored
mmc-hs400-enhanced-strobe is used to claim that the host can support hs400 mode with enhanced strobe introduced by emmc 5.1 spec. Signed-off-by:
-
Geert Uytterhoeven authored
Submitters of device tree binding documentation may forget to CC the subsystem maintainer if this is missing. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Ludovic Desroches authored
Activating wakeup event is not enough to get a wakeup signal. The corresponding events have to be enabled in the Interrupt Status Enable Register too. It follows the specification and is needed at least by sdhci-of-at91. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
-
Yuan, Juntao authored
In sectors alignment check, brq->data.blocks means sectors of the previous mqrq since data.blocks for mqrq_cur hasn't been updated yet. data.blocks will be updated later in mmc_blk_packed_hdr_wrq_prep or mmc_blk_rw_rq_prep. static int mmc_blk_issue_rw_rq(struct mmc_queue *mq, ...... ...... struct mmc_blk_request *brq = &mq->mqrq_cur->brq; Signed-off-by:Yuan Juntao <juntao.yuan@intel.com> Signed-off-by:
-
Simon Horman authored
Since commit 7ce45e95 ("mmc: sdhci: SD tuning is broken for some controllers") sdhci_execute_tuning() no longer includes a timeout in its loop counter(s) so remove portion of the comment regarding this. Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Wolfram Sang authored
Replace hardcoded values with meaningful names and document what we know. Signed-off-by:
-
- 24 Jul, 2016 2 commits
-
-
Linus Torvalds authored
-
git://github.com/ceph/ceph-clientLinus Torvalds authored
Pull ceph fix from Ilya Dryomov: "A fix for a long-standing bug in the incremental osdmap handling code that caused misdirected requests, tagged for stable" The tag is signed with a brand new key - Sage is on vacation and I didn't anticipate this" * tag 'ceph-for-4.7-rc8' of git://github.com/ceph/ceph-client: libceph: apply new_state before new_up_client on incrementals
-
