On 64 bit systems we write past the end of the arg[] array.

Fixes: 8e84c258 ('wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The eth_hdr is never defined in this driver but it gets compiled
without any warning/error because kernel has defined eth_hdr.

Fix it by defining our own p_ethhdr and use it instead of eth_hdr.

Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While receiving a packet on SDIO interface, we allocate skb with
size multiple of SDIO block size. We need to resize this skb
after RX using packet length from RX header.

Cc: <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.1+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.

This patch fixes https://bugzilla.kernel.org/show_bug.cgi?id=63881.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Matthieu Baerts <matttbe@gmail.com>
Cc: Stable <stable@vger.kernel.org> [3.0 +]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All of the rtlwifi drivers have an error in the routine that tests if
the data is "special". If it is, the subsequant transmission will be
at the lowest rate to enhance reliability. The 16-bit quantity is
big-endian, but was being extracted in native CPU mode. One of the
effects of this bug is to inhibit association under some conditions
as the TX rate is too high.

Based on suggestions by Joe Perches, the entire routine is rewritten.

One of the local headers contained duplicates of some of the ETH_P_XXX
definitions. These are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Stable <stable@vger.kernel.org> [2.6.38+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix possible NULL (sc->dfs_detector) pointer dereference.

Detected by Smatch:
drivers/net/wireless/ath/ath9k/dfs_debug.c:67 read_file_dfs()
error: we previously assumed 'sc->dfs_detector' could be null (see line 47)
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use correct width enums when setup
radar_detect_widths for DFS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since:

commit 36323f81
Author: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Date:   Mon Jul 23 21:33:42 2012 +0200

    mac80211: move TX station pointer and restructure TX

we do not pass sta pointer to rt2x00queue_create_tx_descriptor_ht(),
hence we do not correctly set station WCID and AMPDU density parameters.

Cc: stable@vger.kernel.org # 3.7+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix to return -ENODEV in the unknown model error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If we do a zero size allocation then it will oops.  Also we can't be
sure the user passes us a NUL terminated string so I've added a
terminator.

This code can only be triggered by root.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

kmalloc on efuse_word can return null, leading to free'ing of
elements in efuse_word on the error exit path even though it has not
been allocated.  Instead, don't free the elements of efuse_word if
kmalloc failed.

Also, kmalloc of any of the arrays in efuse_word[] can also fail,
leading to undefined contents in the remaining elements leading to
problems when free'ing these elements later on.  So kzalloc efuse_word
to ensure the kfree on the remaining elements won't cause breakage.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While parsing TLVs, return failure if number of remaining bytes
are less than current tlv length. This avoids invalid memory
access.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As tlv_buf_len is decremented at the end of the loop, we may have
accessed invalid memory in the last iteration.
Modify the while condition and add a break statement at the
begining of the loop to fix the problem.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With "while (length)" check we may end up in accessing invalid
memory in last iteration.
This patch makes sure that tlv length is not less than the length
of structure mwifiex_power_group when min/max power is calculated.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

__le16 to u16 conversion is missing for "pg_tlv_hdr->length"
in mwifiex_get_power_level(). This creates a problem on big
endian machines.
It is resolved by changing definition of the structure
and making required endianness changes.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Before we loop for next iteration we adjust the buffer pointer and
"resp_len":

		curr += (tlv_len + sizeof(tlv_hdr->header));
		resp_len -= (tlv_len + sizeof(tlv_hdr->header));

If "resp_len" gets set to negative then it counts as a high positive
value.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is a typo in the struct member name on assignment when checking
rtlphy->current_chan_bw == HT_CHANNEL_WIDTH_20_40, the check uses pwrgroup_ht40
for bound limit and uses pwrgroup_ht20 when assigning instead.
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org [3.0+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On rt2800_config_channel_rf53xx function the member default_power1 is checked
for bound limit, but default_power2 is used instead.
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes a suspicious rcu derference warning.

Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to avoid very silly Kconfig dependencies for modules
using this routine.
Signed-off-by: David S. Miller <davem@davemloft.net>

The max_vfs parameter has a limit of 63 and silently fails (adding 0 vfs) when
it is out of range. This patch adds a warning so that the user knows something
went wrong. Also, this patch moves the warning in ixgbe_enable_sriov() to where
max_vfs is checked, so that even an out of range value will show the deprecated
warning. Previously, an out of range parameter didn't even warn the user to use
the new sysfs interface instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes multiple problems in the link modes display in ethtool.
Newer parts have more complicated methods to determine actual link
capabilities.  Older parts cannot communicate with their SFP modules.
Finally, all the available defines are not displayed by ethtool.  This
updates the link modes to be as accurate as possible depending on what data
is available to the driver at any given time.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:

<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT

and on HOSTB you do:
ping6 HOSTA -s2000    (MTU is 1500)

Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>

As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.

Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If reassembled packet would fit into outdev MTU, it is not fragmented
according the original frag size and it is send as single big packet.

The second case is if skb is gso. In that case fragmentation does not happen
according to the original frag size.

This patch fixes these.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lennart says: "I haven't been able to spend time on mv643xx_eth for a
while now, so if you want to take over maintainership, I'd be fine with
that."
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

With psched_ratecfg_precompute(), tbf can deal with 64bit rates.
Add two new attributes so that tc can use them to break the 32bit
limit.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of stations in use is kept in the num_rx_pools counter
in the ixgbe_adapter structure. This is in turn used by the queue
allocation scheme to determine how many queues are needed to support
the number of pools in use with the current feature set.

This works as long as the pools are added and destroyed in order
because (num_rx_pools * queues_per_pool) is equal to the last
queue in use by a pool. But as soon as you delete a pool out of
order this is no longer the case. So the above multiplication
allocates to few queues and a pool may reference a ring that has
not been allocated/initialized.

To resolve use the bit mask of in use pools to determine the final
pool being used and allocate enough queues so that we don't
inadvertently remove its queues.

# ip link add link eth2 \
	numtxqueues 4 numrxqueues 4 txqueuelen 50 type macvlan
# ip link set dev macvlan0 up
# ip link add link eth2 \
	numtxqueues 4 numrxqueues 4 txqueuelen 50 type macvlan
# ip link set dev macvlan1 up
# for i in {0..100}; do
  ip link set dev macvlan0 down; ip link set dev macvlan0 up;
  done;
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the recent support for layer 2 hardware acceleration, I added a
few references to real_num_rx_queues and num_rx_queues which are
only available with CONFIG_RPS.

The fix is first to remove unnecessary references to num_rx_queues.
Because the hardware offload case is limited to cases where RX queues
and TX queues are equal we only need a single check. Then wrap the
single case in an ifdef.

The patch that introduce this is here,

commit a6cc0cfa
Author: John Fastabend <john.r.fastabend@intel.com>
Date:   Wed Nov 6 09:54:46 2013 -0800

    net: Add layer 2 hardware acceleration operations for macvlan devices
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the rfc 4191 said, the Router Preference and Lifetime values in a
::/0 Route Information Option should override the preference and lifetime
values in the Router Advertisement header. But when the kernel deals with
a ::/0 Route Information Option, the rt6_get_route_info() always return
NULL, that means that overriding will not happen, because those default
routers were added without flag RTF_ROUTEINFO in rt6_add_dflt_router().

In order to deal with that condition, we should call rt6_get_dflt_router
when the prefix length is 0.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0628b123 ("netfilter: nfnetlink: add batch support and use it
from nf_tables") introduced a bug leading to various crashes in netlink_ack
when netlink message with invalid nlmsg_len was sent by an unprivileged
user.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When trying to delete a table >= 256 using iproute2 the local table
will be deleted.
The table id is specified as a netlink attribute when it needs more then
8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0).
Preconditions to matching the table id in the rule delete code
doesn't seem to take the "table id in netlink attribute" into condition
so the frh_get_table helper function never gets to do its job when
matching against current rule.
Use the helper function twice instead of peaking at the table value directly.

Originally reported at: http://bugs.debian.org/724783Reported-by: Nicolas HICHER <nhicher@avencall.com>
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take ip6_fl_lock before to read and update
a label.

v2: protect only the relevant code
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the last RFC 6437 does not give any constraints
for lifetime of flow labels, the previous RFC 3697
spoke of a minimum of 120 seconds between
reattribution of a flow label.

The maximum linger is currently set to 60 seconds
and does not allow this configuration without
CAP_NET_ADMIN right.

This patch increase the maximum linger to 150
seconds, allowing more flexibility to standard
users.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is already possible to set/put/renew a label
with IPV6_FLOWLABEL_MGR and setsockopt. This patch
add the possibility to get information about this
label (current value, time before expiration, etc).

It helps application to take decision for a renew
or a release of the label.

v2:
 * Add spin_lock to prevent race condition
 * return -ENOENT if no result found
 * check if flr_action is GET

v3:
 * move the spin_lock to protect only the
   relevant code
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

By moving code around, we avoid :

1) A reload of iph->ihl (bit field, so needs a mask)

2) A conditional test (replaced by a conditional mov on x86)
   Fast path loads iph->protocol anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tested in VLAB Works Xtensa simulation.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Here is one more pull request for the 3.13 window.  This is primarily
composed of downstream pull requests that were posted while I was
traveling during the last part of the 3.12 release.

For the mac80211 bits, Johannes says:

"I have two DFS fixes (ath9k already supports DFS) and a fix for a
pointer race."

And...

"In this round for mac80211-next I have:
 * mesh channel switch support
 * a CCM rewrite, using potential hardware offloads
 * SMPS for AP mode
 * RF-kill GPIO driver updates to make it usable as an ACPI driver
 * regulatory improvements
 * documentation fixes
 * DFS for IBSS mode
 * and a few small other fixes/improvements"

For the TI driver bits, Luca says:

"Some patches intended for 3.13.  Eliad continues upstreaming pending
patches from the internal tree."

For the iwlwifi bits, Emmanuel says:

"There are a few fixes from Johannes mostly clean up patches. We have
also a few other fixes that are relevant for the new firmware that has
not been released yet."

For the Bluetooth bits, Gustavo says:

"A last fix to the 3.12. I ended forgetting to send it before, I hope we can
still make the way to 3.12. It is a revert and it fixes an issue with bluetooth
suspend/hibernate that had many bug reports. Please pull or let me know of any
problems. Thanks!"  (Obviously, that one didn't make 3.12...)

Also...

"One more big pull request for 3.13. These are the patches we queued during
last week. Here you will find a lot of improvements to the HCI and L2CAP and
MGMT layers with the main ones being a better debugfs support and end of work
of splitting L2CAP into Core and Socket parts."

Additionally, there is one ath9k patch to enable DFS in IBSS mode for
that driver.

I appreciate your consideration for taking this extra pull request
this cycle.  Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem