Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tristram Ha says:

====================
net: dsa: microchip: add KSZ9893 switch support

This series of patches is to modify the KSZ9477 DSA driver to support
running KSZ9893 switch.

The KSZ9893 switch is similar to KSZ9477 except the ingress tail tag has
1 byte instead of 2 bytes.  The XMII register that governs the MAC
communication also has different register definitions.

v1
- Put KSZ9893 tagging in separate patch
- Remove other switch support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add KSZ9893 switch support in KSZ9477 driver.  This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.

The XMII register that governs how the host port communicates with the
MAC also has different register definitions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes.  The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document additional Microchip KSZ9477 family switches.

Show how KSZ8565 switch should be configured as the host port is port 7
instead of port 5.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2019-03-01

This series adds multipath offload support and contains some small updates
to mlx5 driver.

Multipath offload support from Roi Dayan:

We are going to track SW multipath route and related nexthops and reflect
that as port affinity to the HW.

1) Some patches are preparation.
2) add the multipath mode and fib events handling.
3) add support to handle offload failure for net error, i.e.
port down.
4) Small updates to match the behavior of multipath

Two small updates from Eran Ben Elisha,
5) Make a function static
6) Update PCIe supported devices list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for net-next:

1) Add .release_ops to properly unroll .select_ops, use it from nft_compat.
   After this change, we can remove list of extensions too to simplify this
   codebase.

2) Update amanda conntrack helper to support v3.4, from Florian Tham.

3) Get rid of the obsolete BUGPRINT macro in ebtables, from
   Florian Westphal.

4) Merge IPv4 and IPv6 masquerading infrastructure into one single module.
   From Florian Westphal.

5) Patchset to remove nf_nat_l3proto structure to get rid of
   indirections, from Florian Westphal.

6) Skip unnecessary conntrack timeout updates in case the value is
   still the same, also from Florian Westphal.

7) Remove unnecessary 'fall through' comments in empty switch cases,
   from Li RongQing.

8) Fix lookup to fixed size hashtable sets on big endian with 32-bit keys.

9) Incorrect logic to deactivate path of fixed size hashtable sets,
   element was being tested to self.

10) Remove nft_hash_key(), the bitmap set is always selected for 16-bit
    keys.

11) Use boolean whenever possible in IPVS codebase, from Andrea Claudi.

12) Enter close state in conntrack if RST matches exact sequence number,
    from Florian Westphal.

13) Initialize dst_cache in tunnel extension, from wenxu.

14) Pass protocol as u16 to xt_check_match and xt_check_target, from
    Li RongQing.

15) SCTP header is granted to be in a linear area from IPVS NAT handler,
    from Xin Long.

16) Don't steal packets coming from slave VRF device from the
    ip_sabotage_in() path, from David Ahern.

17) Fix unsafe update of basechain stats, from Li RongQing.

18) Make sure CONNTRACK_LOCKS is power of 2 to let compiler optimize
    modulo operation as bitwise AND, from Li RongQing.

19) Use device_attribute instead of internal definition in the IDLETIMER
    target, from Sami Tolvanen.

20) Merge redir, masq and IPv4/IPv6 NAT chain types, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2019-03-02

Here's one more bluetooth-next pull request for the 5.1 kernel:

 - Added support for MediaTek MT7663U and MT7668U UART devices
 - Cleanups & fixes to the hci_qca driver
 - Fixed wakeup pin behavior for QCA6174A controller

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the support of enabling MT7663U and MT7668U Bluetooth function
running on the top of btmtkuart driver.

There are a few differences between MT766[3,8]U and MT7622 where
MT766[3,8]U are standalone devices based on UART transport while MT7622
bluetooth is a built-in device on MediaTek SoC communicating with the host
through BTIF serial transport. Thus, extra setup sequence is necessary
for these standalone devices such as remote regulator and reset control via
GPIO, baud rate changing handshake between the host and device and so on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Update binding document with adding support of MT7663U and MT7668U UART
devices to mediatek-bluetooth.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The current 300ms delay after a baudrate change is extremely long.
For WCN3990 it is sufficient to wait 10ms after the baudrate change
request has been sent over the wire.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Merge tag 'wireless-drivers-next-for-davem-2019-03-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.1

Last set of patches. A new hardware support for mt76 otherwise quite
normal.

Major changes:

mt76

* add driver for MT7603E/MT7628

ath10k

* more preparation for SDIO support

wil6210

* support up to 20 stations in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If register_netdev() is failed to register sitn->fb_tunnel_dev,
it will go to err_reg_dev and forget to free netdev(sitn->fb_tunnel_dev).

BUG: memory leak
unreferenced object 0xffff888378daad00 (size 512):
  comm "syz-executor.1", pid 4006, jiffies 4295121142 (age 16.115s)
  hex dump (first 32 bytes):
    00 e6 ed c0 83 88 ff ff 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
backtrace:
    [<00000000d6dcb63e>] kvmalloc include/linux/mm.h:577 [inline]
    [<00000000d6dcb63e>] kvzalloc include/linux/mm.h:585 [inline]
    [<00000000d6dcb63e>] netif_alloc_netdev_queues net/core/dev.c:8380 [inline]
    [<00000000d6dcb63e>] alloc_netdev_mqs+0x600/0xcc0 net/core/dev.c:8970
    [<00000000867e172f>] sit_init_net+0x295/0xa40 net/ipv6/sit.c:1848
    [<00000000871019fa>] ops_init+0xad/0x3e0 net/core/net_namespace.c:129
    [<00000000319507f6>] setup_net+0x2ba/0x690 net/core/net_namespace.c:314
    [<0000000087db4f96>] copy_net_ns+0x1dc/0x330 net/core/net_namespace.c:437
    [<0000000057efc651>] create_new_namespaces+0x382/0x730 kernel/nsproxy.c:107
    [<00000000676f83de>] copy_namespaces+0x2ed/0x3d0 kernel/nsproxy.c:165
    [<0000000030b74bac>] copy_process.part.27+0x231e/0x6db0 kernel/fork.c:1919
    [<00000000fff78746>] copy_process kernel/fork.c:1713 [inline]
    [<00000000fff78746>] _do_fork+0x1bc/0xe90 kernel/fork.c:2224
    [<000000001c2e0d1c>] do_syscall_64+0xc8/0x580 arch/x86/entry/common.c:290
    [<00000000ec48bd44>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<0000000039acff8a>] 0xffffffffffffffff
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c39 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calculating the multipath hash for input routes the flow info is
not available and therefore should not be used.

Fixes: 24ba1440 ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Cc: wenxu <wenxu@ucloud.cn>
Acked-by: wenxu <wenxu@ucloud.cn>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: fixes and improvements

This series aims to improve the Marvell PPv2 driver and to fix various
issues we encountered while testing the ports in many different
configurations. The series is based on top of Russell PPv2 phylink
rework and improvement.

I'm not sending a v2 of the previous fixes series as half the patches
are not the same and lots of development happened in between.

While this series contains fixes, it's sent to net-next as it is based
on top of Russell patches that were merged into net-next. I'm also
aiming at net-next as the series reworks critical paths of the PPv2
driver, such as the reset handling of various blocks, to let more weeks
for users to tests and for possible fixes to be sent before it lands
into a stable kernel version.

The series is divided into three parts:

- Patches 1 to 3 are cosmetic changes, sent alongside the series, as I
  saw these small issues while working on this.

- Patches 5 to 8 are fixing (or improving) individual issues that we
  found while testing PPv2.1 and PPv2.2 ports while using various
  interfaces.

  Notable fixes are we support back RGMII interfaces (on both PPv2.1 and
  PPv2.2), as their support was broken by previous patches. We also
  reworked the RXQ computation as the RXQ assignment was not checking
  the maximum number of RXQ available, and was broken for PPv2.1.

- As discussed in a previous fixes series, patches 9 to 15 rework the
  way blocks are set in reset in the PPv2 engine (plus related changes).

  There are four blocks we want to control the reset status: two MAC
  (GMAC and XLG MAC) and two PCS (MPCS and XPCS). The XLG MAC is used
  for 10G connexions and uses the MPCS or the XPCS depending on the mode
  used (10GKR / XAUI / RXAUI) and the GMAC is used for the other modes.

  The idea is to set all blocks in reset by default, and when not used,
  and to de-assert the reset only when a block is used. There are four
  cases to take in account:

  1. Boot time: all four blocks should be put in reset, as we do not
     know their initial state (configured by the firmware/bootloader).

  2. Link up: only the blocks used by a given mode should be put out of
     reset (eg. 10GKR uses the XLG MAC and the MPCS).

  3. Mode reconfiguration: some ports may support mode reconfiguration,
     and switching between the GMAC and the XLG MAC (or between the two
     PCS). All blocks should be put in reset, and only the one used
     should be put out of reset.

  4. Link down: all four blocks are put in reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds calls in the stop() helper to ensure both MACs and
both PCS blocks are set in reset when the user manually sets a port
down. This is done so that we have the exact same block reset states at
boot time and when a port is set down.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets both the XPCS and MPCS blocks in reset when they aren't
used. This is done both at boot time and when reconfiguring a port mode.
The advantage now is that only the PCS used is set out of reset when the
port is configured (10GKR uses the MCPS while RXAUI uses the XPCS).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes sure both PPv2 MACs (GMAC + XLG MAC) are set in reset
while a port is reconfigured. This is done so that we make sure a MAC is
in a reset state when not used, as only one of the two will be set out
of reset after the port is configured properly.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch reworks the way the XLG MAC is set in reset: the XLG MAC is
set in reset at probe time and taken out of this state only when used.
The idea is to move forward a situation where only the blocks used are
taken out of reset. This also has the effect to handle the GMAC and the
XLG MAC in a similar way (the GMAC already is set in reset at boot
time).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch force the XLG MAC link state in the phylink link_up() and
link_down() helpers when not using in-band auto-negotiation. This mimics
what's already done for the GMAC and follows what's advised in the
phylink documentation.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch improves the XLG configuration function, to only update the
XLG configuration register when a change is needed. This helps not
writing over and over the same XLG configuration each time phylink
request the MAC to be configured. This mimics the GMAC configuration
function.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch modifies the port_disable() helper to always disable both the
GMAC and the XLG MAC when called. At boot time we do not know of a port
was enabled in the firmware/bootloader, and if so what mode was used
(hence which of the two MACs was used).

This also help in implementing a logic where all blocks are disabled
when not used, and only enabled regarding the current mode used on a
given port.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GMAC configuration helper modifies values in the auto-negotiation
register. Some of its values require the port to be forced down when
modifying their values. This patches fixes the check made on the bit to
be updated in this register, so that the port is forced down when
needed. This fix cases where some of those parameters were updated, but
not taken into account, such as when using RGMII interfaces.

Fixes: d14e078f ("net: marvell: mvpp2: only reprogram what is necessary on mac_config")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch fixes the computation of RXQs being used by the PPv2 driver,
which is set depending on the PPv2 engine version and the queue mode
used. There are three cases:

- PPv2.1: 1 RXQ per CPU.
- PPV2.2 with MVPP2_QDIST_MULTI_MODE: 1 RXQ per CPU.
- PPv2.2 with MVPP2_QDIST_SINGLE_MODE: 1 RXQ is shared between the CPUs.

The PPv2 engine supports a maximum of 32 queues per port. This patch
adds a check so that we do not overstep this maximum.

It appeared the calculation was broken for PPv2.1 engines since
f8c6ba84, as PPv2.1 ports ended up with a single RXQ while they
needed 4. This patch fixes it.

Fixes: f8c6ba84 ("net: mvpp2: use only one rx queue per port per CPU")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Phylink validate function is the Marvell PPv2 driver makes a check
on the GoP id. This is valid an has to be done when using PPv2.2 engines
but makes no sense when using PPv2.1. The check done when using an RGMII
interface makes sure the GoP id is not 0, but this breaks PPv2.1. Fixes
it.

Fixes: 0fb628f0 ("net: mvpp2: fix phylink handling of invalid PHY modes")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a check on the PPv2 version in-use not to reconfigure
the port mode when an interface is updated when using PPv2.1 as the
functions called are PPv2.2 specific.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We had a check in the mvpp2_mac_link_down() function (called by phylink)
to avoid disabling the port when link interrupts are used. It turned out
the interrupt can still be used with the port disabled. We can thus
remove this check.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cosmetic patch fix the alignment of the MVPP2_GMAC_CONFIG_MII_SPEED
macro definition.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell PPv2 port structure stores the GoP id of a given port. This
information is specific to PPv2.2, but cannot be used by PPv2.1. Update
its comment to denote this specificity.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This cosmetic patch fixes a typo made in a comment in the Marvell PPv2
Ethernet driver header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_carrier_off() should be called only after register_netdev().
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arjun Vynipadath says:

====================
cxgb4/cxgb4vf: VF link state support

This series of patches adds support for ndo_set_vf_link_state in
cxgb4 driver.

Patch 1 implements ndo_set_vf_link_state
Patch 2 reverts the existing force_link_up behaviour for cxgb4vf driver.

v2:
- Using reverse christmas tree for variable declaration in Patch 1
- Patch 2 has no change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reverting force link up changes since this behaviour can be
achieved using VF link state feature.

Reverts:
commit 0913667a ("cxgb4vf: Forcefully link up virtual interfaces")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ndo_set_vf_link_state to control the link states associated
with the virtual interfaces.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4VF.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/mt7530.c:649:3-4: Unneeded semicolon
drivers/net/ethernet/cisco/enic/enic_clsf.c:35:2-3: Unneeded semicolon
drivers/net/ethernet/faraday/ftgmac100.c:1640:2-3: Unneeded semicolon
drivers/net/ethernet/mediatek/mtk_eth_soc.c:229:2-3: Unneeded semicolon
drivers/net/usb/sr9700.c:437:2-3: Unneeded semicolon

Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com> for mt7530 and mtk_eth_soc
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: 64bit support for SO_MAX_PACING_RATE

64bit kernels adopted 64bit type for sk_max_pacing_rate in linux-4.20

We can change how we implement SO_MAX_PACING_RATE socket option
to support 64bit values to/from user space as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For legacy applications using 32bit variable, SO_MAX_PACING_RATE
has to cap the returned value to 0xFFFFFFFF, meaning that
rates above 34.35 Gbit are capped.

This patch allows applications to read socket pacing rate
at full resolution, if they provide a 64bit variable to store it,
and the kernel is 64bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>