commit cb43285f upstream.

[ Upstream Commit 84e32a06 ]

Commit 84e32a06 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
    *rsp->in_ptr = 0;

Add additional check to make sure the pointer is valid. following
call stack will be seen

---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>]  [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8  EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 70f340df upstream.

The non-DT platform that uses this driver (actually the AVR32) was taking a bad
branch for determining if the IP would use gpio for CS.
Adding the presence of DT as a condition fixes this issue.

Fixes: 48203034 ("spi: atmel: add support for the internal chip-select of the spi controller")
Reported-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[nicolas.ferre@atmel.com: extract from ml discussion]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 310d3d31 upstream.

This patch fixes a race between setting of SCF_SEND_DELAYED_TAS
in transport_send_task_abort(), and check of the same bit in
transport_check_aborted_status().

It adds a __transport_check_aborted_status() version that is
used by target_execute_cmd() when se_cmd->t_state_lock is
held, and a transport_check_aborted_status() wrapper for
all other existing callers.

Also, it handles the case where the check happens before
transport_send_task_abort() gets called.  For this, go
ahead and set SCF_SEND_DELAYED_TAS early when necessary,
and have transport_send_task_abort() send the abort.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0f4a9431 upstream.

To address the bug where fabric driver level shutdown
of se_cmd occurs at the same time when TMR CMD_T_ABORTED
is happening resulting in a -1 ->cmd_kref, this patch
adds a CMD_T_FABRIC_STOP bit that is used to determine
when TMR + driver I_T nexus shutdown is happening
concurrently.

It changes target_sess_cmd_list_set_waiting() to obtain
se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local
reference in target_wait_for_sess_cmds() and invoke extra
target_put_sess_cmd() during Task Aborted Status (TAS)
when necessary.

Also, it adds a new target_wait_free_cmd() wrapper around
transport_wait_for_tasks() for the special case within
transport_generic_free_cmd() to set CMD_T_FABRIC_STOP,
and is now aware of CMD_T_ABORTED + CMD_T_TAS status
bits to know when an extra transport_put_cmd() during
TAS is required.

Note transport_generic_free_cmd() is expected to block on
cmd->cmd_wait_comp in order to follow what iscsi-target
expects during iscsi_conn context se_cmd shutdown.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ebde1ca5 upstream.

This patch fixes a bug in TMR task aborted status (TAS)
handling when multiple sessions are connected to the
same target WWPN endpoint and se_node_acl descriptor,
resulting in TASK_ABORTED status to not be generated
for aborted se_cmds on the remote port.

This is due to core_tmr_handle_tas_abort() incorrectly
comparing se_node_acl instead of se_session, for which
the multi-session case is expected to be sharing the
same se_node_acl.

Instead, go ahead and update core_tmr_handle_tas_abort()
to compare tmr_sess + cmd->se_sess in order to determine
if the LUN_RESET was received on a different I_T nexus,
and TASK_ABORTED status response needs to be generated.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a6d9bb1c upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active TMRs,
triggered during se_cmd + se_tmr_req descriptor
shutdown + release via core_tmr_drain_tmr_list().

To address this bug, go ahead and obtain a local
kref_get_unless_zero(&se_cmd->cmd_kref) for active I/O
to set CMD_T_ABORTED, and transport_wait_for_tasks()
followed by the final target_put_sess_cmd() to drop
the local ->cmd_kref.

Also add two new checks within target_tmr_work() to
avoid CMD_T_ABORTED -> TFO->queue_tm_rsp() callbacks
ahead of invoking the backend -> fabric put in
transport_cmd_check_stop_to_fabric().

For good measure, also change core_tmr_release_req()
to use list_del_init() ahead of se_tmr_req memory
free.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit febe562c upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active se_cmd
I/O, that can be triggered during se_cmd descriptor
shutdown + release via core_tmr_drain_state_list() code.

To address this bug, add common __target_check_io_state()
helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE
checking, and set CMD_T_ABORTED + obtain ->cmd_kref for
both cases ahead of last target_put_sess_cmd() after
TFO->aborted_task() -> transport_cmd_finish_abort()
callback has completed.

It also introduces SCF_ACK_KREF to determine when
transport_cmd_finish_abort() needs to drop the second
extra reference, ahead of calling target_put_sess_cmd()
for the final kref_put(&se_cmd->cmd_kref).

It also updates transport_cmd_check_stop() to avoid
holding se_cmd->t_state_lock while dropping se_cmd
device state via target_remove_from_state_list(), now
that core_tmr_drain_state_list() is holding the
se_device lock while checking se_cmd state from
within TMR logic.

Finally, move transport_put_cmd() release of SGL +
TMR + extended CDB memory into target_free_cmd_mem()
in order to avoid potential resource leaks in TMR
ABORT_TASK + LUN_RESET code-paths.  Also update
target_release_cmd_kref() accordingly.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3b43b71f upstream.

After login to the desktop on Dell Inspiron 3162,
there's a very loud background noise comes from the builtin speaker.
The noise does not go away even if the speaker is muted.

The noise disappears after using the aamix fixup.

Codec: Realtek ALC3234
Address: 0
AFG Function Id: 0x1 (unsol 1)
    Vendor Id: 0x10ec0255
    Subsystem Id: 0x10280725
    Revision Id: 0x100002
    No Modem Function Group found

BugLink: http://bugs.launchpad.net/bugs/1549620Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7e31a015 upstream.

Some Skylake machines show the codec probe errors in certain
situations, e.g. HP Z240 desktop fails to probe the onboard Realtek
codec at reloading the snd-hda-intel module like:
  snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x000000
  snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: lastcmd=0x000f0000
  snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x000f0000
  snd_hda_intel 0000:00:1f.3: Codec #0 probe error; disabling it...
  hdaudio hdaudioC0D2: no AFG or MFG node found
  snd_hda_intel 0000:00:1f.3: no codecs initialized

Also, HP G470 G3 suffers from the similar problem, as reported in
bugzilla below.  On this machine, the codec probe error appears even
at a fresh boot.

As Libin suggested, the same workaround used for Broxton in the commit
[6639484d: ALSA: hda - disable dynamic clock gating on Broxton
 before reset] can be applied for Skylake in order to fix this problem.
The Intel HW team also confirmed that this is needed for SKL.

This patch makes the workaround applied to both SKL and BXT
platforms.  The referred macros are moved and one superfluous macro
(IS_BROXTON()) is another one (IS_BXT()) as well.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112731Suggested-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 041bd12e upstream.

This reverts commit 874bbfe6.

Workqueue used to implicity guarantee that work items queued without
explicit CPU specified are put on the local CPU.  Recent changes in
timer broke the guarantee and led to vmstat breakage which was fixed
by 176bed1d ("vmstat: explicitly schedule per-cpu work on the CPU
we need it to run on").

vmstat is the most likely to expose the issue and it's quite possible
that there are other similar problems which are a lot more difficult
to trigger.  As a preventive measure, 874bbfe6 ("workqueue: make
sure delayed work run in local cpu") was applied to restore the local
CPU guarnatee.  Unfortunately, the change exposed a bug in timer code
which got fixed by 22b886dd ("timers: Use proper base migration in
add_timer_on()").  Due to code restructuring, the commit couldn't be
backported beyond certain point and stable kernels which only had
874bbfe6 started crashing.

The local CPU guarantee was accidental more than anything else and we
want to get rid of it anyway.  As, with the vmstat case fixed,
874bbfe6 is causing more problems than it's fixing, it has been
decided to take the chance and officially break the guarantee by
reverting the commit.  A debug feature will be added to force foreign
CPU assignment to expose cases relying on the guarantee and fixes for
the individual cases will be backported to stable as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 874bbfe6 ("workqueue: make sure delayed work run in local cpu")
Link: http://lkml.kernel.org/g/20160120211926.GJ10810@quack.suse.cz
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Daniel Bilik <daniel.bilik@neosystem.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Shaohua Li <shli@fb.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Bilik <daniel.bilik@neosystem.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d6e022f1 upstream.

When looking up the pool_workqueue to use for an unbound workqueue,
workqueue assumes that the target CPU is always bound to a valid NUMA
node.  However, currently, when a CPU goes offline, the mapping is
destroyed and cpu_to_node() returns NUMA_NO_NODE.

This has always been broken but hasn't triggered often enough before
874bbfe6 ("workqueue: make sure delayed work run in local cpu").
After the commit, workqueue forcifully assigns the local CPU for
delayed work items without explicit target CPU to fix a different
issue.  This widens the window where CPU can go offline while a
delayed work item is pending causing delayed work items dispatched
with target CPU set to an already offlined CPU.  The resulting
NUMA_NO_NODE mapping makes workqueue try to queue the work item on a
NULL pool_workqueue and thus crash.

While 874bbfe6 has been reverted for a different reason making the
bug less visible again, it can still happen.  Fix it by mapping
NUMA_NO_NODE to the default pool_workqueue from unbound_pwq_by_node().
This is a temporary workaround.  The long term solution is keeping CPU
-> NODE mapping stable across CPU off/online cycles which is being
worked on.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/g/1454424264.11183.46.camel@gmail.com
Link: http://lkml.kernel.org/g/1453702100-2597-1-git-send-email-tangchen@cn.fujitsu.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4fa11ec7 upstream.

During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.

This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6736fde9 upstream.

The code within wait_event_interruptible() is called with
!TASK_RUNNING, so mustn't call any functions that can sleep,
like mutex_lock().

Since we re-check the list_empty() in a loop after the wait,
it's safe to simply use list_empty() without locking.

This bug has existed forever, but was only discovered now
because all userspace implementations, including the default
'rfkill' tool, use poll() or select() to get a readable fd
before attempting to read.

Fixes: c64fb016 ("rfkill: create useful userspace interface")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1ca8ec53 upstream.

commit 0ff53d09 sets the next tick interrupt to the last jiffies update,
i.e. in the past, because the forward operation is invoked before the set
operation. There is no resulting damage (yet), but we get an extra pointless
tick interrupt.

Revert the order so we get the next tick interrupt in the future.

Fixes: commit 0ff53d09 "tick: sched: Force tick interrupt and get rid of softirq magic"
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1453893967-3458-1-git-send-email-wanpeng.li@hotmail.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3f416f22 upstream.

Mel reported stddev reporting was broken due to following commit:

	106a94a0 ("perf stat: Introduce read_counters function")

This commit merged interval and overall counters reading into single
read_counters function.

The old interval code cleaned the stddev data for some reason (it's
never displayed in interval mode) and the mentioned commit kept on
cleaning the stddev data in merged function, which resulted in the
stddev not being displayed.

Removing the wrong stddev data cleanup init_stats call.
Reported-and-Tested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: 106a94a0 ("perf stat: Introduce read_counters function")
Link: http://lkml.kernel.org/r/1453290995-18485-4-git-send-email-jolsa@kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e912e685 upstream.

This phone needs to be handled by a specialised firmware tool
and is reported to crash irrevocably if cdc-acm takes it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b64a1cbe upstream.

This reverts commit ebd43516.

We should not be sleeping inside spin_lock.

Fixes: ebd43516 ("Staging: panel: usleep_range is preferred over udelay")
Cc: Sirnam Swetha <theonly.ultimate@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reported-by: Huang, Ying <ying.huang@intel.com>
Tested-by: Huang, Ying <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 327b882d upstream.

Commit f79b0d9c ("staging: speakup: Fixed warning <linux/serial.h>
instead of <asm/serial.h>") broke the port information in the speakup
driver: SERIAL_PORT_DFNS only gets defined if asm/serial.h is included,
and no other header includes asm/serial.h.

We here make sure serialio.c does get the arch-specific definition of
SERIAL_PORT_DFNS from asm/serial.h, if any.

Along the way, this makes sure that we do have information for the
requested serial port number (index)

Fixes: f79b0d9c ("staging: speakup: Fixed warning <linux/serial.h> instead of <asm/serial.h>")
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d0eb20a8 upstream.

Commit ca369d51 ("block/sd: Fix device-imposed transfer length
limits") accidentally switched optimal I/O size reporting from bytes to
block layer sectors.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: ca369d51Reviewed-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cd8140c6 upstream.

Commit d15f9d69 ("libceph: check data_len in ->alloc_msg()")
mistakenly bumped the log level on the "tid %llu unknown, skipping"
message.  Turn it back into a dout() - stray replies are perfectly
normal when OSDs flap, crash, get killed for testing purposes, etc.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dbc0d3ca upstream.

ceph_msg_footer is 21 bytes long, while ceph_msg_footer_old is only 13.
Don't skip too much when CEPH_FEATURE_MSG_AUTH isn't negotiated.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e7a88e82 upstream.

The contract between try_read() and try_write() is that when called
each processes as much data as possible.  When instructed by osd_client
to skip a message, try_read() is violating this contract by returning
after receiving and discarding a single message instead of checking for
more.  try_write() then gets a chance to write out more requests,
generating more replies/skips for try_read() to handle, forcing the
messenger into a starvation loop.
Reported-by: Varada Kari <Varada.Kari@sandisk.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Varada Kari <Varada.Kari@sandisk.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 67645d76 upstream.

There are a number of problems with revoking a "was sending" message:

(1) We never make any attempt to revoke data - only kvecs contibute to
con->out_skip.  However, once the header (envelope) is written to the
socket, our peer learns data_len and sets itself to expect at least
data_len bytes to follow front or front+middle.  If ceph_msg_revoke()
is called while the messenger is sending message's data portion,
anything we send after that call is counted by the OSD towards the now
revoked message's data portion.  The effects vary, the most common one
is the eventual hang - higher layers get stuck waiting for the reply to
the message that was sent out after ceph_msg_revoke() returned and
treated by the OSD as a bunch of data bytes.  This is what Matt ran
into.

(2) Flat out zeroing con->out_kvec_bytes worth of bytes to handle kvecs
is wrong.  If ceph_msg_revoke() is called before the tag is sent out or
while the messenger is sending the header, we will get a connection
reset, either due to a bad tag (0 is not a valid tag) or a bad header
CRC, which kind of defeats the purpose of revoke.  Currently the kernel
client refuses to work with header CRCs disabled, but that will likely
change in the future, making this even worse.

(3) con->out_skip is not reset on connection reset, leading to one or
more spurious connection resets if we happen to get a real one between
con->out_skip is set in ceph_msg_revoke() and before it's cleared in
write_partial_skip().

Fixing (1) and (3) is trivial.  The idea behind fixing (2) is to never
zero the tag or the header, i.e. send out tag+header regardless of when
ceph_msg_revoke() is called.  That way the header is always correct, no
unnecessary resets are induced and revoke stands ready for disabled
CRCs.  Since ceph_msg_revoke() rips out con->out_msg, introduce a new
"message out temp" and copy the header into it before sending.
Reported-by: Matt Conner <matt.conner@keepertech.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Matt Conner <matt.conner@keepertech.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 103502a3 upstream.

Before this patch, a process with some permissive seccomp filter
that was applied by root without NO_NEW_PRIVS was able to add
more filters to itself without setting NO_NEW_PRIVS by setting
the new filter from a throwaway thread with NO_NEW_PRIVS.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e4b133cc upstream.

There is a race discovered by Juri, where we are able to:
- create and read a sysfs file before policy->governor_data is being set
  to a non NULL value.
  OR
- set policy->governor_data to NULL, and reading a file before being
  destroyed.

And so such a crash is reported:

Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = edfc8000
[0000000c] *pgd=bfc8c835
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 4 PID: 1730 Comm: cat Not tainted 4.5.0-rc1+ #463
Hardware name: ARM-Versatile Express
task: ee8e8480 ti: ee930000 task.ti: ee930000
PC is at show_ignore_nice_load_gov_pol+0x24/0x34
LR is at show+0x4c/0x60
pc : [<c058f1bc>]    lr : [<c058ae88>]    psr: a0070013
sp : ee931dd0  ip : ee931de0  fp : ee931ddc
r10: ee4bc290  r9 : 00001000  r8 : ef2cb000
r7 : ee4bc200  r6 : ef2cb000  r5 : c0af57b0  r4 : ee4bc2e0
r3 : 00000000  r2 : 00000000  r1 : c0928df4  r0 : ef2cb000
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: adfc806a  DAC: 00000051
Process cat (pid: 1730, stack limit = 0xee930210)
Stack: (0xee931dd0 to 0xee932000)
1dc0:                                     ee931dfc ee931de0 c058ae88 c058f1a4
1de0: edce3bc0 c07bfca4 edce3ac0 00001000 ee931e24 ee931e00 c01fcb90 c058ae48
1e00: 00000001 edce3bc0 00000000 00000001 ee931e50 ee8ff480 ee931e34 ee931e28
1e20: c01fb33c c01fcb0c ee931e8c ee931e38 c01a5210 c01fb314 ee931e9c ee931e48
1e40: 00000000 edce3bf0 befe4a00 ee931f78 00000000 00000000 000001e4 00000000
1e60: c00545a8 edce3ac0 00001000 00001000 befe4a00 ee931f78 00000000 00001000
1e80: ee931ed4 ee931e90 c01fbed8 c01a5038 ed085a58 00020000 00000000 00000000
1ea0: c0ad72e4 ee931f78 ee8ff488 ee8ff480 c077f3fc 00001000 befe4a00 ee931f78
1ec0: 00000000 00001000 ee931f44 ee931ed8 c017c328 c01fbdc4 00001000 00000000
1ee0: ee8ff480 00001000 ee931f44 ee931ef8 c017c65c c03deb10 ee931fac ee931f08
1f00: c0009270 c001f290 c0a8d968 ef2cb000 ef2cb000 ee8ff480 00000020 ee8ff480
1f20: ee8ff480 befe4a00 00001000 ee931f78 00000000 00000000 ee931f74 ee931f48
1f40: c017d1ec c017c2f8 c019c724 c019c684 ee8ff480 ee8ff480 00001000 befe4a00
1f60: 00000000 00000000 ee931fa4 ee931f78 c017d2a8 c017d160 00000000 00000000
1f80: 000a9f20 00001000 befe4a00 00000003 c000ffe4 ee930000 00000000 ee931fa8
1fa0: c000fe40 c017d264 000a9f20 00001000 00000003 befe4a00 00001000 00000000
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
1fc0: 000a9f20 00001000 befe4a00 00000003 00000000 00000000 00000003 00000001
pgd = edfc4000
[0000000c] *pgd=bfcac835
1fe0: 00000000 befe49dc 000197f8 b6e35dfc 60070010 00000003 3065b49d 134ac2c9

[<c058f1bc>] (show_ignore_nice_load_gov_pol) from [<c058ae88>] (show+0x4c/0x60)
[<c058ae88>] (show) from [<c01fcb90>] (sysfs_kf_seq_show+0x90/0xfc)
[<c01fcb90>] (sysfs_kf_seq_show) from [<c01fb33c>] (kernfs_seq_show+0x34/0x38)
[<c01fb33c>] (kernfs_seq_show) from [<c01a5210>] (seq_read+0x1e4/0x4e4)
[<c01a5210>] (seq_read) from [<c01fbed8>] (kernfs_fop_read+0x120/0x1a0)
[<c01fbed8>] (kernfs_fop_read) from [<c017c328>] (__vfs_read+0x3c/0xe0)
[<c017c328>] (__vfs_read) from [<c017d1ec>] (vfs_read+0x98/0x104)
[<c017d1ec>] (vfs_read) from [<c017d2a8>] (SyS_read+0x50/0x90)
[<c017d2a8>] (SyS_read) from [<c000fe40>] (ret_fast_syscall+0x0/0x1c)
Code: e5903044 e1a00001 e3081df4 e34c1092 (e593300c)
---[ end trace 5994b9a5111f35ee ]---

Fix that by making sure, policy->governor_data is updated at the right
places only.
Reported-and-tested-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb2a24a1 upstream.

There are two definitions of pxa_cpufreq_change_voltage, with slightly
different prototypes after one of them had its argument marked 'const'.
Now the other one (for !CONFIG_REGULATOR) produces a harmless warning:

drivers/cpufreq/pxa2xx-cpufreq.c: In function 'pxa_set_target':
drivers/cpufreq/pxa2xx-cpufreq.c:291:36: warning: passing argument 1 of 'pxa_cpufreq_change_voltage' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
   ret = pxa_cpufreq_change_voltage(&pxa_freq_settings[idx]);
                                    ^
drivers/cpufreq/pxa2xx-cpufreq.c:205:12: note: expected 'struct pxa_freqs *' but argument is of type 'const struct pxa_freqs *'
 static int pxa_cpufreq_change_voltage(struct pxa_freqs *pxa_freq)
            ^

This changes the prototype in the same way as the other, which
avoids the warning.

Fixes: 03c22990 (cpufreq: pxa: make pxa_freqs arrays const)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit acc14694 upstream.

Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is unsigned.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 000e0949 upstream.

Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).

When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.

Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.

Fixes: b5cf88e4 ("(gpio-fan): Add thermal control hooks")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6220f4eb upstream.

Since Linux 4.0 the CPU fan speed is going up and down on Dell Studio
XPS 8000 and 8100 for unknown reasons. The 8100 was already
blacklisted in commit a4b45b25 ("hwmon: (dell-smm) Blacklist
Dell Studio XPS 8100"). This patch blacklists the XPS 8000.

Without further debugging on the affected machine, it is not possible
to find the problem. For more details see
https://bugzilla.kernel.org/show_bug.cgi?id=100121Signed-off-by: Thorsten Leemhuis <linux@leemhuis.info>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4511f716 upstream.

When a new cooling device is registered, we need to update the
thermal zone to set the new registered cooling device to a proper
state.

This fixes a problem that the system is cool, while the fan devices
are left running on full speed after boot, if fan device is registered
after thermal zone device.

Here is the history of why current patch looks like this:
https://patchwork.kernel.org/patch/7273041/

Reference:https://bugzilla.kernel.org/show_bug.cgi?id=92431Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ff140fea upstream.

Current thermal code does not handle system sleep well because
1. the cooling device cooling state may be changed during suspend
2. the previous temperature reading becomes invalid after resumed because
   it is got before system sleep
3. updating thermal zone device during suspending/resuming
   is wrong because some devices may have already been suspended
   or may have not been resumed.

Thus, the proper way to do this is to cancel all thermal zone
device update requirements during suspend/resume, and after all
the devices have been resumed, reset and update every registered
thermal zone devices.

This also fixes a regression introduced by:
Commit 19593a1f ("ACPI / fan: convert to platform driver")
Because, with above commit applied, all the fan devices are attached
to the acpi_general_pm_domain, and they are turned on by the pm_domain
automatically after resume, without the awareness of thermal core.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=78201
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=91411Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bb431ba2 upstream.

After thermal zone device registered, as we have not read any
temperature before, thus tz->temperature should not be 0,
which actually means 0C, and thermal trend is not available.
In this case, we need specially handling for the first
thermal_zone_device_update().

Both thermal core framework and step_wise governor is
enhanced to handle this. And since the step_wise governor
is the only one that uses trends, so it's the only thermal
governor that needs to be updated.
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: szegad <szegadlo@poczta.onet.pl>
Tested-by: prash <prash.n.rao@gmail.com>
Tested-by: amish <ammdispose-arch@yahoo.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9f177686 upstream.

Maximum number of EQE capacity per CQ was mistakenly exposed
as CQE. Fix that.

Fixes: 938fe83c ("net/mlx5_core: New device capabilities handling")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fbbeb863 upstream.

The current code is problematic when the QP creation and ipoib is used to
support NFS and NFS desires to do IO for paging purposes. In that case, the
GFP_KERNEL allocation in qib_qp.c causes a deadlock in tight memory
situations.

This fix adds support to create queue pair with GFP_NOIO flag for connected
mode only to cleanly fail the create queue pair in those situations.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 09dc9cd6 upstream.

The code produces the following trace:

[1750924.419007] general protection fault: 0000 [#3] SMP
[1750924.420364] Modules linked in: nfnetlink autofs4 rpcsec_gss_krb5 nfsv4
dcdbas rfcomm bnep bluetooth nfsd auth_rpcgss nfs_acl dm_multipath nfs lockd
scsi_dh sunrpc fscache radeon ttm drm_kms_helper drm serio_raw parport_pc
ppdev i2c_algo_bit lpc_ich ipmi_si ib_mthca ib_qib dca lp parport ib_ipoib
mac_hid ib_cm i3000_edac ib_sa ib_uverbs edac_core ib_umad ib_mad ib_core
ib_addr tg3 ptp dm_mirror dm_region_hash dm_log psmouse pps_core
[1750924.420364] CPU: 1 PID: 8401 Comm: python Tainted: G D
3.13.0-39-generic #66-Ubuntu
[1750924.420364] Hardware name: Dell Computer Corporation PowerEdge
860/0XM089, BIOS A04 07/24/2007
[1750924.420364] task: ffff8800366a9800 ti: ffff88007af1c000 task.ti:
ffff88007af1c000
[1750924.420364] RIP: 0010:[<ffffffffa0131d51>] [<ffffffffa0131d51>]
qib_mcast_qp_free+0x11/0x50 [ib_qib]
[1750924.420364] RSP: 0018:ffff88007af1dd70  EFLAGS: 00010246
[1750924.420364] RAX: 0000000000000001 RBX: ffff88007b822688 RCX:
000000000000000f
[1750924.420364] RDX: ffff88007b822688 RSI: ffff8800366c15a0 RDI:
6764697200000000
[1750924.420364] RBP: ffff88007af1dd78 R08: 0000000000000001 R09:
0000000000000000
[1750924.420364] R10: 0000000000000011 R11: 0000000000000246 R12:
ffff88007baa1d98
[1750924.420364] R13: ffff88003ecab000 R14: ffff88007b822660 R15:
0000000000000000
[1750924.420364] FS:  00007ffff7fd8740(0000) GS:ffff88007fc80000(0000)
knlGS:0000000000000000
[1750924.420364] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1750924.420364] CR2: 00007ffff597c750 CR3: 000000006860b000 CR4:
00000000000007e0
[1750924.420364] Stack:
[1750924.420364]  ffff88007b822688 ffff88007af1ddf0 ffffffffa0132429
000000007af1de20
[1750924.420364]  ffff88007baa1dc8 ffff88007baa0000 ffff88007af1de70
ffffffffa00cb313
[1750924.420364]  00007fffffffde88 0000000000000000 0000000000000008
ffff88003ecab000
[1750924.420364] Call Trace:
[1750924.420364]  [<ffffffffa0132429>] qib_multicast_detach+0x1e9/0x350
[ib_qib]
[1750924.568035]  [<ffffffffa00cb313>] ? ib_uverbs_modify_qp+0x323/0x3d0
[ib_uverbs]
[1750924.568035]  [<ffffffffa0092d61>] ib_detach_mcast+0x31/0x50 [ib_core]
[1750924.568035]  [<ffffffffa00cc213>] ib_uverbs_detach_mcast+0x93/0x170
[ib_uverbs]
[1750924.568035]  [<ffffffffa00c61f6>] ib_uverbs_write+0xc6/0x2c0 [ib_uverbs]
[1750924.568035]  [<ffffffff81312e68>] ? apparmor_file_permission+0x18/0x20
[1750924.568035]  [<ffffffff812d4cd3>] ? security_file_permission+0x23/0xa0
[1750924.568035]  [<ffffffff811bd214>] vfs_write+0xb4/0x1f0
[1750924.568035]  [<ffffffff811bdc49>] SyS_write+0x49/0xa0
[1750924.568035]  [<ffffffff8172f7ed>] system_call_fastpath+0x1a/0x1f
[1750924.568035] Code: 66 2e 0f 1f 84 00 00 00 00 00 31 c0 5d c3 66 2e 0f 1f
84 00 00 00 00 00 66 90 0f 1f 44 00 00 55 48 89 e5 53 48 89 fb 48 8b 7f 10
<f0> ff 8f 40 01 00 00 74 0e 48 89 df e8 8e f8 06 e1 5b 5d c3 0f
[1750924.568035] RIP  [<ffffffffa0131d51>] qib_mcast_qp_free+0x11/0x50
[ib_qib]
[1750924.568035]  RSP <ffff88007af1dd70>
[1750924.650439] ---[ end trace 73d5d4b3f8ad4851 ]

The fix is to note the qib_mcast_qp that was found.   If none is found, then
return EINVAL indicating the error.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4bfdf635 upstream.

ib_send_cm_drep() calls cm_enter_timewait() while holding a spinlock
that can be locked from inside an interrupt handler. Hence do not
enable interrupts inside cm_enter_timewait() if called with interrupts
disabled.

This patch fixes e.g. the following deadlock:
Acked-by: Erez Shitrit <erezsh@mellanox.com>

=================================
[ INFO: inconsistent lock state ]
4.4.0-rc7+ #1 Tainted: G            E
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
swapper/8/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&cm_id_priv->lock)->rlock){?.+...}, at: [<ffffffffa036eec4>] cm_establish+0x
74/0x1b0 [ib_cm]
{HARDIRQ-ON-W} state was registered at:
  [<ffffffff810a3c11>] mark_held_locks+0x71/0x90
  [<ffffffff810a3e87>] trace_hardirqs_on_caller+0xa7/0x1c0
  [<ffffffff810a3fad>] trace_hardirqs_on+0xd/0x10
  [<ffffffff8151c40b>] _raw_spin_unlock_irq+0x2b/0x40
  [<ffffffffa036ea8e>] cm_enter_timewait+0xae/0x100 [ib_cm]
  [<ffffffffa036ff76>] ib_send_cm_drep+0xb6/0x190 [ib_cm]
  [<ffffffffa052ed08>] srp_cm_handler+0x128/0x1a0 [ib_srp]
  [<ffffffffa0370340>] cm_process_work+0x20/0xf0 [ib_cm]
  [<ffffffffa0371335>] cm_dreq_handler+0x135/0x2c0 [ib_cm]
  [<ffffffffa03733c5>] cm_work_handler+0x75/0xd0 [ib_cm]
  [<ffffffff8107184d>] process_one_work+0x1bd/0x460
  [<ffffffff81073148>] worker_thread+0x118/0x420
  [<ffffffff81078454>] kthread+0xe4/0x100
  [<ffffffff8151cbbf>] ret_from_fork+0x3f/0x70
irq event stamp: 1672286
hardirqs last  enabled at (1672283): [<ffffffff81408ec0>] poll_idle+0x10/0x80
hardirqs last disabled at (1672284): [<ffffffff8151d304>] common_interrupt+0x84/0x89
softirqs last  enabled at (1672286): [<ffffffff8105b4dc>] _local_bh_enable+0x1c/0x50
softirqs last disabled at (1672285): [<ffffffff8105b697>] irq_enter+0x47/0x70

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&cm_id_priv->lock)->rlock);
  <Interrupt>
    lock(&(&cm_id_priv->lock)->rlock);

 *** DEADLOCK ***

no locks held by swapper/8/0.

stack backtrace:
CPU: 8 PID: 0 Comm: swapper/8 Tainted: G            E   4.4.0-rc7+ #1
Hardware name: Dell Inc. PowerEdge R430/03XKDV, BIOS 1.0.2 11/17/2014
 ffff88045af5e950 ffff88046e503a88 ffffffff81251c1b 0000000000000007
 0000000000000006 0000000000000003 ffff88045af5ddc0 ffff88046e503ad8
 ffffffff810a32f4 0000000000000000 0000000000000000 0000000000000001
Call Trace:
 <IRQ>  [<ffffffff81251c1b>] dump_stack+0x4f/0x74
 [<ffffffff810a32f4>] print_usage_bug+0x184/0x190
 [<ffffffff810a36e2>] mark_lock_irq+0xf2/0x290
 [<ffffffff810a3995>] mark_lock+0x115/0x1b0
 [<ffffffff810a3b8c>] mark_irqflags+0x15c/0x170
 [<ffffffff810a4fef>] __lock_acquire+0x1ef/0x560
 [<ffffffff810a53c2>] lock_acquire+0x62/0x80
 [<ffffffff8151bd33>] _raw_spin_lock_irqsave+0x43/0x60
 [<ffffffffa036eec4>] cm_establish+0x74/0x1b0 [ib_cm]
 [<ffffffffa036f031>] ib_cm_notify+0x31/0x100 [ib_cm]
 [<ffffffffa0637f24>] srpt_qp_event+0x54/0xd0 [ib_srpt]
 [<ffffffffa0196052>] mlx4_ib_qp_event+0x72/0xc0 [mlx4_ib]
 [<ffffffffa00775b9>] mlx4_qp_event+0x69/0xd0 [mlx4_core]
 [<ffffffffa006000e>] mlx4_eq_int+0x51e/0xd50 [mlx4_core]
 [<ffffffffa006084f>] mlx4_msi_x_interrupt+0xf/0x20 [mlx4_core]
 [<ffffffff810b67b0>] handle_irq_event_percpu+0x40/0x110
 [<ffffffff810b68bf>] handle_irq_event+0x3f/0x70
 [<ffffffff810ba7f9>] handle_edge_irq+0x79/0x120
 [<ffffffff81007f3d>] handle_irq+0x5d/0x130
 [<ffffffff810071fd>] do_IRQ+0x6d/0x130
 [<ffffffff8151d309>] common_interrupt+0x89/0x89
 <EOI>  [<ffffffff8140895f>] cpuidle_enter_state+0xcf/0x200
 [<ffffffff81408aa2>] cpuidle_enter+0x12/0x20
 [<ffffffff810990d6>] call_cpuidle+0x36/0x60
 [<ffffffff81099163>] cpuidle_idle_call+0x63/0x110
 [<ffffffff8109930a>] cpu_idle_loop+0xfa/0x130
 [<ffffffff8109934e>] cpu_startup_entry+0xe/0x10
 [<ffffffff8103c443>] start_secondary+0x83/0x90

Fixes: commit be4b4993 ("IB/cm: Do not queue work to a device that's going away")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ee1cdcda upstream.

The commit 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks")
re-enabled BLOCK interrupts with regard to make cyclic transfers work. However,
this change becomes a regression for non-cyclic transfers as interrupt counters
under stress test had been grown enormously (approximately per 4-5 bytes in the
UART loop back test).

Taking into consideration above enable BLOCK interrupts if and only if channel
is programmed to perform cyclic transfer.

Fixes: 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 611dcadb upstream.

When having cyclic transfers, the channel was paused when performing
suspend but was not correctly resumed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9ee ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2895b2ca upstream.

Cyclic transfer callbacks rely on block completion interrupts which were
disabled in commit ff7b05f2 ("dmaengine/dw_dmac: Don't handle block
interrupts").  This re-enables block interrupts so the cyclic callbacks
can work.  Other transfer types are not affected as they set the INT_EN
bit only on the last block.

Fixes: ff7b05f2 ("dmaengine/dw_dmac: Don't handle block interrupts")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit df3bb8a0 upstream.

Commit 61e183f8 ("dmaengine/dw_dmac: Reconfigure interrupt and
chan_cfg register on resume") moved some channel initialisation to
a new function which must be called before starting a transfer.

This updates dw_dma_cyclic_start() to use dwc_dostart() like the other
modes, thus ensuring dwc_initialize() gets called and removing some code
duplication.

Fixes: 61e183f8 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>