When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If cmd19 timeout or response crcerr occurs during execute_tuning(),
it need invoke msdc_reset_hw(). Otherwise SDIO IRQ can't be detected.
Signed-off-by: jjian zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e9 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.
Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e9 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for 4 bit instances on TI's J721E devices. Because these
instances have no DLL, introduce a DLL_PRESENT flag and make sure DLL
related registers are only accessed when it is present. Also add a
separate set_clock callback for this compatible.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The 8 bit IP on the TI's J721E device departs from the AM654x IP in some
ways which require special handling. Create a driver_data structure
which holds the pltfm_data and a flags field which is used to indicate
these differences. These are the following:

1. The pins are not muxed with anything else inside the SoC and hence the
   IOMUX_ENABLE field does not exist. Add a flag which is used to
   indicate the presence of the field.

2. The register field used to select DLL frequency is 3 bit wide as
   compared to 2 bits in AM65x. Add another flag which differentiates
   between 3 bit and 2 bit fields.

3. The strobe select field is 8 bit wide as compared to 4 bits for
   AM65x. Add yet another flag to indicate this difference. Strobe select
   is used only for HS400 speed mode, support for which has not yet been
   added in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add binding documentation for mmc host controllers present on TI's J721E
SOC. The 4 bit IP on J721E doesn't have a phy DLL so make DLL related
properties as optional for that compatible. Also add an optional
strobe-sel property used for HS400 speed mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Bools are initialized to 'false' by default.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Quirks show up in new SoCs as well, so the naming should be generic.
Describe them by what they do.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Recent changes have made it much more likely that clocks are not available,
when the SDHCI driver is first probed. However, that is a situation that
the driver can cope with just fine.

To avoid confusion, don't output an error when this happens.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set the PHY DLL delay for each timing mode, which is used to sample the clock
accurately and make the clock more stable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Introduce some PHY DLL delays properties to help to sample the PHY clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For the Spreadtrum SD host controller, when we changed the clock to be
more than 52M, we should enable the PHY DLL which is used to track the
clock frequency to make the clock work more stable. Otherwise deviation
may occur of the higher clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add HS400 enhanced strobe mode support for Spreadtrum SD host controller.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Implement the get_max_timeout_count() interface to set the Spredtrum SD
host controller actual maximum timeout count.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For the Spreadtrum SC9860 platform, we should enable another gate clock
'2x_enable' to make the SD host controller work well.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For some Spreadtrum platforms like SC9860 platform, we should enable another
gate clock '2x_enable' to make the SD host controller work well. Thus add
documentation for this optional clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Missed to check the enable clock's return value, fix it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The calculation of slots results in a value in the range 1..8
and so slots can never be zero.  The check for slots == 0 is
always going to be false, hence it is redundant and can be
removed.

Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Switch the DT binding to a YAML schema to enable the DT validation.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The MMC controllers have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Print an error message and return if DLL fails to lock.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Line wrapping with the regmap_*() functions is way more conservative
than required by the 80 character rule. Expand the function calls out to
use less number of lines.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If bus_register fails. On its error handling path, it has cleaned up
what it has done. There is no need to call bus_unregister again.
Otherwise, if bus_unregister is called, issues such as null-ptr-deref
will arise.

Syzkaller report this:

kobject_add_internal failed for memstick (error: -12 parent: bus)
BUG: KASAN: null-ptr-deref in sysfs_remove_file_ns+0x1b/0x40 fs/sysfs/file.c:467
Read of size 8 at addr 0000000000000078 by task syz-executor.0/4460

Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xa9/0x10e lib/dump_stack.c:113
 __kasan_report+0x171/0x18d mm/kasan/report.c:321
 kasan_report+0xe/0x20 mm/kasan/common.c:614
 sysfs_remove_file_ns+0x1b/0x40 fs/sysfs/file.c:467
 sysfs_remove_file include/linux/sysfs.h:519 [inline]
 bus_remove_file+0x6c/0x90 drivers/base/bus.c:145
 remove_probe_files drivers/base/bus.c:599 [inline]
 bus_unregister+0x6e/0x100 drivers/base/bus.c:916 ? 0xffffffffc1590000
 memstick_init+0x7a/0x1000 [memstick]
 do_one_initcall+0xb9/0x3b5 init/main.c:914
 do_init_module+0xe0/0x330 kernel/module.c:3468
 load_module+0x38eb/0x4270 kernel/module.c:3819
 __do_sys_finit_module+0x162/0x190 kernel/module.c:3909
 do_syscall_64+0x72/0x2a0 arch/x86/entry/common.c:298
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: baf8532a ("memstick: initial commit for Sony MemoryStick support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On the Amlogic G12A SoC family, (only) the SDIO controller fails to access
the data from DRAM, leading to a broken controller.

But each MMC controller has 1,5KiB of SRAM after the registers, that can
be used as bounce buffer to avoid direct DRAM access from the integrated
DMAs (this SRAM may be used by the boot ROM when DRAM is not yet initialized).

The quirk is to disable the chained descriptor for this controller, and
use this SRAM memory zone as buffer for the bounce buffer fallback mode.

The performance hit hasn't been evaluated, but the fix has been tested
using a WiFi AP6398S SDIO module, and the iperf3 Bandwidth measurement gave
55.2 Mbits/sec over a 63 Hours long test, with the SDIO ios set as High-Speed
at 50MHz clock. It gave 170 Mbits/sec as SDR104 and 200MHz clock.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On the Amlogic G12A SoC family, (only) the SDIO controller has a bug which
makes any DRAM access from the MMC controller fail.

Add the amlogic,dram-access-quirk property so signal this particular
controller has this bug and needs a quirk to work properly.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Both the Renesas and Uniphier implementations perform actions which
affect runtime PM before calling into the core tmio_mmc_host_probe()
which enabled runtime PM. Move pm_runtime_enable() from the core and
tmio_mmc_host_probe() into each drivers probe() so it can be called
before any clocks or other resources are switched on.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The driver for android-goldfish uses a pointer to get from the private
goldfish_mmc_host structure to the generic mmc_host structure.
However the latter is always immediately preceding the former in
memory, so compute its address with a subtraction (which is cheaper than a
dereference) and drop the superfluous pointer.

No functional change intended.
Signed-off-by: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Our HW engineers informed us that HS400 is not working on these SoC
revisions.

Fixes: 0f4e2054 ("mmc: renesas_sdhi: disable HS400 on H3 ES1.x and M3-W ES1.[012]")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull ceph fixes from Ilya Dryomov:
 "A change to call iput() asynchronously to avoid a possible deadlock
  when iput_final() needs to wait for in-flight I/O (e.g. readahead) and
  a fixup for a cleanup that went into -rc1"

* tag 'ceph-for-5.2-rc4' of git://github.com/ceph/ceph-client:
  ceph: fix error handling in ceph_get_caps()
  ceph: avoid iput_final() while holding mutex or in dispatch thread
  ceph: single workqueue for inode related works

Pull xen fix from Juergen Gross:
 "Just one fix for the Xen block frontend driver avoiding allocations
  with order > 0"

* tag 'for-linus-5.2b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-blkfront: switch kcalloc to kvcalloc for large array allocation

Pull s390 fixes from Heiko Carstens:

 - fix stack unwinder: the stack unwinder rework has on off-by-one bug
   which prevents following stack backchains over more than one context
   (e.g. irq -> process).

 - fix address space detection in exception handler: if user space
   switches to access register mode, which is not supported anymore, the
   exception handler may resolve to the wrong address space.

* tag 's390-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/unwind: correct stack switching during unwind
  s390/mm: fix address space detection in exception handling

Pull MIPS fixes from Paul Burton:

 - Declare ginvt() __always_inline due to its use of an argument as an
   inline asm immediate.

 - A VDSO build fix following Kbuild changes made this cycle.

 - A fix for boot failures on txx9 systems following memory
   initialization changes made this cycle.

 - Bounds check virt_addr_valid() to prevent it spuriously indicating
   that bogus addresses are valid, in turn fixing hardened usercopy
   failures that have been present since v4.12.

 - Build uImage.gz for pistachio systems by default, since this is the
   image we need in order to actually boot on a board.

 - Remove an unused variable in our uprobes code.

* tag 'mips_fixes_5.2_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: uprobes: remove set but not used variable 'epc'
  MIPS: pistachio: Build uImage.gz by default
  MIPS: Make virt_addr_valid() return bool
  MIPS: Bounds check virt_addr_valid
  MIPS: TXx9: Fix boot crash in free_initmem()
  MIPS: remove a space after -I to cope with header search paths for VDSO
  MIPS: mark ginvt() as __always_inline

Pull yet more SPDX updates from Greg KH:
 "Another round of SPDX header file fixes for 5.2-rc4

  These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
  added, based on the text in the files. We are slowly chipping away at
  the 700+ different ways people tried to write the license text. All of
  these were reviewed on the spdx mailing list by a number of different
  people.

  We now have over 60% of the kernel files covered with SPDX tags:
	$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
	Files checked:            64533
	Files with SPDX:          40392
	Files with errors:            0

  I think the majority of the "easy" fixups are now done, it's now the
  start of the longer-tail of crazy variants to wade through"

* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.2-rc4 to resolve
  a number of reported issues.

  The most "notable" one here is the kernel headers in proc^Wsysfs
  fixes. Those changes move the header file info into sysfs and fixes
  the build issues that you reported.

  Other than that, a bunch of small habanalabs driver fixes, some fpga
  driver fixes, and a few other tiny driver fixes.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  habanalabs: Read upper bits of trace buffer from RWPHI
  habanalabs: Fix virtual address access via debugfs for 2MB pages
  fpga: zynqmp-fpga: Correctly handle error pointer
  habanalabs: fix bug in checking huge page optimization
  habanalabs: Avoid using a non-initialized MMU cache mutex
  habanalabs: fix debugfs code
  uapi/habanalabs: add opcode for enable/disable device debug mode
  habanalabs: halt debug engines on user process close
  test_firmware: Use correct snprintf() limit
  genwqe: Prevent an integer overflow in the ioctl
  parport: Fix mem leak in parport_register_dev_model
  fpga: dfl: expand minor range when registering chrdev region
  fpga: dfl: Add lockdep classes for pdata->lock
  fpga: dfl: afu: Pass the correct device to dma_mapping_error()
  fpga: stratix10-soc: fix use-after-free on s10_init()
  w1: ds2408: Fix typo after 49695ac4 (reset on output_write retry with readback)
  kheaders: Do not regenerate archive if config is not changed
  kheaders: Move from proc to sysfs
  lkdtm/bugs: Adjust recursion test to avoid elision
  lkdtm/usercopy: Moves the KERNEL_DS test to non-canonical

Pull i2c fixes from Wolfram Sang:
 "I2C has a driver bugfix and a MAINTAINERS fix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Karthikeyan Ramasubramanian is MIA
  i2c: xiic: Add max_read_len quirk