Compatibility version is checked upon packet reception
before calling any handler. For this reason it does need to
be checked once more in the handler itself.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

The source address has already been checked in
batadv_check_management_packet() upon packet reception and
therefore it does not need to be checked again in
ogm_process()
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

print the interface along with the new neighbor mac address
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

the sequence number is not stored in struct neigh_node,
therefore there is no need to pass such value to the
neigh_node creation procedure.

At the moment the value is only used by a debug message, but
given the fact that the seqno is not related to the neighbor
object, it is better to print it elsewhere.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

While it makes sense to send each broadcast thrice on 802.11 (WLAN) interfaces
as broadcasts are often unreliable on these, there is no reason to do so on
other interface types.

The increased the overhead can be harmful on low-bandwidth links like VPN
connections over slow internet lines, therefore it is better to reduce the
number of broadcast packets sent on non-wireless links to one.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Previously batadv_is_wifi_iface() did two things at once: looking up a
net_device from an interface index, and determining if it is a wifi device.

The second part is useful itself when the caller already has a net_device
reference.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

net/core/skbuff.c: In function ‘__alloc_skb_head’:
net/core/skbuff.c:203:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c: In function ‘__alloc_skb’:
net/core/skbuff.c:279:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c:280:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c: In function ‘build_skb’:
net/core/skbuff.c:348:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c:349:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Signed-off-by: David S. Miller <davem@davemloft.net>

IFF_NOARP affects what kind of neighbor entries are created
(nud NOARP or nud INCOMPLETE). If the flag changes, flush the arp
cache to refresh all entries.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>

v2->v3: shortened notifier_info struct name
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new netdevice notifier infrastructure to pass along changed flags.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>

v2->v3: shortened notifier_info struct name
Signed-off-by: David S. Miller <davem@davemloft.net>

So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>

v2->v3: fix typo on simeth
	shortened dev_getter
	shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>

As Stephen proposed:
Since bonding supports configuration via iproute (netlink) and sysfs, I think
it is time to purge the old ifenslave code out of Documentation/networking
and update the documentation.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct spelling typo
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the xmit_hash_policy pointer is always valid and not dependent on
anything, we can change it while the bond device is up and running. The
only downside would be the out of order packets but that is a small price
to pay.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

module_spi_driver() removes some boilerplate and makes the code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netpoll_rx_disable() will always return 0, it is no use and looks wordy,
so remove the unnecessary code and get rid of it in _dev_open and _dev_close.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.

The aim of this short series is to provide GSO in software for MPLS packets
whose skbs are GSO.

Change since v4:

Update first patch of the series to use 16 bits for all *_headers
rather than just inner_*_headers

Simon Horman (2):
  net: Use 16bits for *_headers fields of struct skbuff
  MPLS: Add limited GSO support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.

The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.

SKB Usage:

When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:

* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
  skb->inner_protocol is added by this patch.

* Set skb->protocol to the new MPLS ethertype of the packet.

* Set skb->network_header to correspond to the
  end of the L3 header, including the MPLS label stack.

I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code.  The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.

Features:

I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols.  Jesse, I understand that
you have some ideas here.  I am more than happy to change my implementation.

This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.

A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload.  Currently no devices support this
and MPLS GSO always falls back to software.

Alternate Implementation:

One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().

I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.

MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.

Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to mitigate ongoing incresase in the size of struct skbuff
use 16 bit integer offsets rather than pointers for inner_*_headers.

This appears to reduce the size of struct skbuff from 0xd0 to 0xc0
bytes on x86_64 with the following all unset.

	CONFIG_XFRM
	CONFIG_NF_CONNTRACK
	CONFIG_NF_CONNTRACK_MODULE
	NET_SKBUFF_NF_DEFRAG_NEEDED
	CONFIG_BRIDGE_NETFILTER
	CONFIG_NET_SCHED
	CONFIG_IPV6_NDISC_NODETYPE
	CONFIG_NET_DMA
	CONFIG_NETWORK_SECMARK
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these
as internal PHY devices.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a comment which explains the real meaning of XCVR_INTERNAL (PHY and
Ethernet MAC in the same package/die) and XCVR_EXTERNAL (PHY and
Ethernet MAC in a different package/die). Most if not all of the drivers
setting their transceiver type already do it the way the comment
describes it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fabio Estevam says:

====================
This series provides support for controlling the PHY regulator in suspend/resume.

Fabio Estevam (5):
  fec: Place the phy regulator in the private structure
  fec: Invert the order of error path sequence
  fec: Disable the PHY regulator on error and removal
  fec: Remove irqs first
  fec: Handle the regulator in suspend/resume
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to save power, let's disable the regulator in the suspend function and
enable it in resume.

Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During probe the clocks are enabled prior than the acquiring the interrupts.

In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of error during probe, disable the PHY regulator.

Do the same in fec_drv_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.

This is wrong because at this point the interrupts have not even been acquired.

Swap failed_init/failed_irq to fix the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().

This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For padded packets, Lancer computes incorrect checksum. The workaround is
to trim such packets. This workaround is mainly for IPv4 packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Lancer, packets that are 32 bytes or less may cause a transmit stall.
The work-around is to pad such packets to a 36 byte length.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking
the same from be_setup() and/or post firmware download.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This changes the PCI power management scheme of the bnx2x driver to be similar
to those of most network drivers - the driver will now changes the power state
into D3hot whenever the driver will be removed, instead of whenever an
interface is unloaded.

This change enables the driver to access its eeprom via ethtool callbacks
even when interfaces are unloaded (such access requires the function to be
in D0active).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the PCI shutdown callback to support un-orderly shutdown, i.e.,
shutdowns in which the remove callback will not be called.

Due to the lack of this functionality, when an un-orderly shutdown occurred,
it was possible for wake-on-lan to remain disabled.

This is now fixed as the callback introduces the correct place in which
`system_state' can be queried and wake-on-lan be configured accordingly.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0eb43b4b
"bnx2x, bnx2fc: Use per port max exchange resources" has changed the number
of available FCoE exchanges, even in scenarios when some of the functions has
no FCoE support; This needlessly degraded the available resources.

Remedy this by calculating the maximal number of functions that may actually
utilize said connection.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A PF should ack the firmware when receiving unknown messages through the VF's
mailbox. This prevents the VF mailbox from being stuck in case of a VF sending
a message unknown to the PF (e.g. VF with more advanced version).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>