- 14 Oct, 2013 11 commits
-
-
Mauro Carvalho Chehab authored
The Stellar firmware load routine is different. Improve it to use the default firmware, if no modprobe parameter tells otherwise. Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> Tested-by:
André Roth <neolynx@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Since kernel 3.8, the initialization for Stellar (sms1000) devices are broken. Those devices have a behaviour different than usual sms1100 and sms2270: they start with one USB ID (devices in cold state), but after firmware load, they get a different USB ID. This weren't docummented at the driver. So, the patches that added support for sms2270 broke it. Properly documment it, and provide a debug log that allows to follow all phases of the device initialization: smsusb_probe: board id=13, interface number 0 smsusb_probe: interface 0 won't be used. Expecting interface 1 to popup smsusb_probe: board id=13, interface number 1 smsusb_probe: smsusb_probe 1 smsusb_probe: endpoint 0 81 02 64 smsusb_probe: endpoint 1 02 02 64 smsusb_probe: stellar device in cold state was found at usb\4-2. smsusb1_load_firmware: sent 38144(38144) bytes, rc 0 smsusb1_load_firmware: read FW dvbt_bda_stellar_usb.inp, size=38144 smsusb_probe: stellar device now in warm state usbcore: registered new interface driver smsusb usb 4-2: USB disconnect, device number 52 usb 4-2: new full-speed USB device number 53 using uhci_hcd usb 4-2: New USB device found, idVendor=187f, idProduct=0100 usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-2: Product: SMS DVBT-BDA Receiver usb 4-2: Manufacturer: Siano Mobile Silicon smsusb_probe: board id=1, interface number 0 smsusb_probe: smsusb_probe 0 smsusb_probe: endpoint 0 81 02 64 smsusb_probe: endpoint 1 02 02 64 smsusb_init_device: in_ep = 81, out_ep = 02 smscore_register_device: allocated 50 buffers smscore_register_device: device ffff88012a00bc00 created smsusb_init_device: smsusb_start_streaming(...). smscore_set_device_mode: set device mode to 4 smsusb1_detectmode: 4 "SMS DVBT-BDA Receiver" smsusb_sendrequest: sending MSG_SMS_INIT_DEVICE_REQ(578) size: 12 smsusb_onresponse: received MSG_SMS_INIT_DEVICE_RES(579) size: 12 smscore_set_device_mode: Success setting device mode. smscore_init_ir: IR port has not been detected smscore_start_device: device ffff88012a00bc00 started, rc 0 smsusb_init_device: device 0xffff88002cfa6000 created smsusb_probe: Device initialized with return code 0 DVB: registering new adapter (Siano Stellar Digital Receiver) usb 4-2: DVB: registering adapter 0 frontend 0 (Siano Mobile Digital MDTV Receiver)... smscore_register_client: ffff88012174a000 693 1 sms_board_dvb3_event: DVB3_EVENT_HOTPLUG smsdvb_hotplug: success smsdvb_module_init: Signed-off-by:
-
Mauro Carvalho Chehab authored
Some messages are not clear, some are debug data, but are shown as errors, and one message is duplicated. Cleanup that mess in order to provide a cleaner log. Signed-off-by:
-
Mauro Carvalho Chehab authored
At this bugzilla and similar ones: https://bugzilla.kernel.org/show_bug.cgi?id=60645 Those debug messages were seen as errors, but they're just debug data, and are OK to appear on sms1100 and sms2270. Re-tag them to appear only if debug is enabled. Signed-off-by:
-
Luis Alves authored
This patch will fix the situation where the mutex was left in a locked state if for some reason the FE init failed. Signed-off-by:
Luis Alves <ljalvs@gmail.com> Reviewed-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Sachin Kamat authored
Driver core sets driver data to NULL upon failure or remove. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Krzysztof Hałasa authored
On certain platforms a sequence of dma_map_sg() and dma_unmap_sg() discards data previously stored in the buffers. Build video headers only after the DMA is completed. Signed-off-by:
Krzysztof Ha?asa <khalasa@piap.pl> [hans.verkuil@cisco.com: fix merge problems due to the recent solo sg_table changes] Signed-off-by:
-
Krzysztof Hałasa authored
Signed-off-by:
-
Krzysztof Hałasa authored
Signed-off-by:
-
Krzysztof Hałasa authored
[m.chehab@samsung.com: Fix CodingStyle: don't use 2 statements on just one line] Signed-off-by:
-
Dan Carpenter authored
The "|" operation has higher precedence that "?:" so this couldn't return both flags set at once as intended. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
- 03 Oct, 2013 12 commits
-
-
Wei Yongjun authored
Fix to return -ENOMEM in the new i2c client and create workqueue error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Michael Opdenacker authored
This patch proposes to remove the IRQF_DISABLED flag from davinci media platform drivers. It's a NOOP since 2.6.35 and it will be removed one day. Signed-off-by:
Michael Opdenacker <michael.opdenacker@free-electrons.com> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Geert Uytterhoeven authored
If NO_DMA=y: warning: (... && VIDEO_RENESAS_VSP1 && ...) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA) drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’: drivers/media/v4l2-core/videobuf2-dma-contig.c:202: error: implicit declaration of function ‘dma_mmap_coherent’ drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’: drivers/media/v4l2-core/videobuf2-dma-contig.c:385: error: implicit declaration of function ‘dma_get_sgtable’ make[7]: *** [drivers/media/v4l2-core/videobuf2-dma-contig.o] Error 1 VIDEO_RENESAS_VSP1 (which doesn't have a platform dependency) selects VIDEOBUF2_DMA_CONTIG, but the latter depends on HAS_DMA. Make VIDEO_RENESAS_VSP1 depend on HAS_DMA to fix this. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
We must not assume that the PCI device is already enabled. Signed-off-by:
-
Ben Hutchings authored
We must call iounmap() and pci_dev_put() when removed and on the probe failure path. Signed-off-by:
-
Ben Hutchings authored
Use phys_addr_t and log format %pa. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Wei Yongjun authored
Fix to return -ENODEV in the subdevice register error handling. Signed-off-by:
-
Luis Alves authored
...and remove the frontend pointer param from cx24117_attach() Signed-off-by:
-
Luis Alves authored
Signed-off-by:
-
Luis Alves authored
Add support for the cx24117 dual DVB-S/S2 frontend. Signed-off-by:
-
Alexey Khoroshilov authored
There is an asymmetry in ttusb_dec_init_usb()-ttusb_init_rc() and ttusb_dec_exit_usb()-ttusb_dec_exit_rc() in terms of resources allocated-deallocated. irq_urb and irq_buffer are allocated in ttusb_dec_init_usb(), while they are deallocated in ttusb_dec_exit_rc(). As a result there is a leak of them in ttusb_dec_probe(). The patch fixes the asymmetry and a leak on a failure path in ttusb_dec_init_usb(). By the way, it - removes usage of -1 as a custom error code, - replaces GFP_ATOMIC by GFP_KERNEL in usb_alloc_coherent() in ttusb_dec_init_usb() as soon as all other memory allocation done with GFP_KERNEL; - refactors ttusb_dec_boot_dsp() in an equivalent way except for returning 0 instead of 1 if ttusb_dec_boot_dsp() succeed in (!mode) branch. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
- 02 Oct, 2013 9 commits
-
-
Mauro Carvalho Chehab authored
Changeset 9e8da9e8 added a parameter to specify the frequency divisor, used by the driver. However, not all places are passing this parameter. So, preserve the previous default, to avoid breaking the existing drivers. Signed-off-by: -
John Horan authored
[media] media: dvb-frontends: ts2020: Added in a option for frequency divider value for s600 devices When the tuner part of the ds3000 driver was split to share code with the m88rs2000 driver, the ts2020 driver used the frequency divider value from the m88rs2000 driver. However the ds3000 driver requires a different value, and this resulted in some frequecies being invisible to the tuner. This patch adds back in the value needed for the ds3000 driver and configured as an option in the dw2102 frontend driver. It may also apply to su3000 devices, which use the same ds3000 driver, but for now it is only applied to the s660 device. Signed-off-by:
John Horan <knasher@gmail.com> Signed-off-by:
-
Michael Krufky authored
Thanks-to: Joe Perches <joe@perches.com> Signed-off-by:
-
Kees Cook authored
Make sure that a format string cannot accidentally leak into the printk buffer. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Christoph Jaeger authored
SIZEOF_ARRAY is not used (anymore). Besides, ARRAY_SIZE, defined in include/linux/kernel.h, should be used rather than explicitly coding some variant of it. Signed-off-by:
Christoph Jaeger <christophjaeger@linux.com> Reviewed-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
Andreas Matthies authored
Reading firmware status register to detect whether firmware is running or not didn't work 100% reliably. That register was likely set by firmware itself which means it could not contain reasonable values until firmware is up and running. Usually it just worked as some garbage value was returned accidentally but it appears that in some cases returned garbage value was 0x00 which was considered "firmware is up and running" by the driver and firmware loading was skipped leaving device to non-working state. Fix problem by removing unreliable check and let the driver keep count whether firmware is loaded or not. Signed-off-by:
Andreas Matthies <a.matthies@gmx.net> Signed-off-by:
-
Peter Senna Tschudin authored
The variable vco_select is only assigned the values true and false. Change its type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by:
Peter Senna Tschudin <peter.senna@gmail.com> Acked-by:
Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by:
-
Ming Lei authored
Complete() will be run with interrupt enabled, so change to spin_lock_irqsave(). These functions may be called inside URB->complete(), so use spin_lock_irqsave(). Signed-off-by:
Ming Lei <ming.lei@canonical.com> Acked-by:
-
Mauro Carvalho Chehab authored
drivers/media/usb/gspca/stk1135.c:615:6: warning: no previous prototype for 'stk1135_try_fmt' [-Wmissing-prototypes] void stk1135_try_fmt(struct gspca_dev *gspca_dev, struct v4l2_format *fmt) ^ drivers/media/usb/gspca/stk1135.c:627:5: warning: no previous prototype for 'stk1135_enum_framesizes' [-Wmissing-prototypes] int stk1135_enum_framesizes(struct gspca_dev *gspca_dev, Signed-off-by:
-
- 26 Sep, 2013 8 commits
-
-
Sylwester Nawrocki authored
Add debug print so it's easier to find any errors resulting from the planes' configuration checks added in commit 8023ed09 "videobuf2-core: Verify planes lengths for output buffers". Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Seung-Woo Kim authored
__qbuf_userptr checks whether provided buffer is large enough, and it returns error without any log. Signed-off-by:
Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by:
Heejin Woo <heejin.woo@samsung.com> Signed-off-by:
-
Ricardo Ribalda authored
Replace the private struct vb2_dma_sg_desc with the struct sg_table so we can benefit from all the helping functions in lib/scatterlist.c for things like allocating the sg or compacting the descriptor. marvel-ccic and solo6x10 drivers, that use this API have been updated. Acked-by:
Andre Heider <a.heider@gmail.com> Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> [s.nawrocki@samsung.com: minor corrections of the changelog] Signed-off-by:
-
Ricardo Ribalda authored
Most DMA engines have limitations regarding the number of DMA segments (sg-buffers) that they can handle. Videobuffers can easily spread through hundreds of pages. In the previous aproach, the pages were allocated individually, this could led to the creation houndreds of dma segments (sg-buffers) that could not be handled by some DMA engines. This patch tries to minimize the number of DMA segments by using alloc_pages. In the worst case it will behave as before, but most of the times it will reduce the number of dma segments Acked-by:
-
Ricardo Ribalda authored
struct v4_file_operations defines the data param as const char __user *data but on vb2 is defined as char __user *data. This patch fixes the warnings produced by this. ie: drivers/qtec/qtec_xform.c:817:2: warning: initialization from incompatible pointer type [enabled by default] drivers/qtec/qtec_xform.c:817:2: warning: (near initialization for ‘qtec_xform_v4l_fops.write’) [enabled by default] Signed-off-by:
-
Andy Shevchenko authored
Instead of passing each byte through stack let's use %*ph specifier to do this job better. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Ondrej Zary authored
Add variable resolution support to Syntek STK1135 subdriver. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Ondrej Zary authored
Add variable resolution support to gspca by allowing subdrivers to specify try_fmt and enum_framesizes functions. Signed-off-by:
-
