- 28 Apr, 2019 20 commits
-
-
Olof Johansson authored
Merge tag 'sunxi-dt64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Allwinner arm64 DT changes for 5.2 Our usual bunch of patches, the most notable one being: - Fixing the DTC warnings - Fix DT bindings not being properly respected, thanks to the DT validation - New Board: Oceanic 5205, Beelink GS1, Orange Pi3 * tag 'sunxi-dt64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (22 commits) arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1 arm64: dts: allwinner: Fix DE2 bus node name arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI arm64: dts: allwinner: h6: Add MMC1 pins arm64: dts: allwinner: h6: Add Orange Pi 3 DTS arm64: dts: allwinner: h6: Introduce Beelink GS1 board dt-bindings: vendor-prefixes: add AZW arm64: dts: allwinner: h6: move MMC pinctrl to dtsi arm64: dts: allwinner: h6: Add device node for SID arm64: dts: allwinner: a64: Fix the Codec I2S binding arm64: dts: allwinner: a64: Add default dr_mode arm64: dts: allwinner: Fix pinctrl node names arm64: dts: allwinner: a64: Add missing PIO clocks arm64: dts: allwinner: a64: Fix display pipeline endpoints arm64: dts: allwinner: a64: Fix the TCON output clock arm64: dts: allwinner: h6: Add Video Engine node arm64: dts: allwinner: a64: Add cross links for the mixers arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support dt-bindings: Add vendor prefix for oceanic ... Signed-off-by:
Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'sunxi-dt-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Allwinner DT changes for 5.2 This PR is pretty significant, but it been mostly about: - Fixing the DTC warnings in most of our DT. We're now down to 2 warnings, from several thousands. - Fixing a good number of minor issues, typos, and so on thanks to the DT validation tools - Describe the MBUS controller and the special DMA RAM mapping on the A13 - Add support for the LRADC on the A83t - Add support for the I2C bus used for the PMIC on the A33 - Start using the DT annotation /omit-if-no-ref/ on our pinctrl nodes * tag 'sunxi-dt-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (65 commits) ARM: dts: sun8i: a83t: Enable USB OTG controller on some boards ARM: dtsi: axp81x: add USB power supply node ARM: dts: sun5i: Reorder pinctrl nodes ARM: dts: sun6i: i7: Remove useless property ARM: dts: sun4i: lime: Fix the USB PHY ID detect GPIO properties ARM: dts: sun4i: protab2: Remove stale pinctrl-names entry ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI ARM: dts: sun8i: v40: bananapi-m2-berry: Sort device node dereferences. ARM: dts: sun5i: Add the MBUS controller dt-bindings: sunxi: Add compatible for OrangePi 3 board ARM: dts: sun8i: a83t: Add I2C2 pinmux setting for PE pins dt-bindings: arm: sunxi: Add Beelink GS1 board ARM: dts: sun8i: tbs-a711: Add support for volume keys input ARM: dts: sunxi: Add R_LRADC support for A83T ARM: dts: sunxi: Improve A33 NAND transfers by using DMA ARM: dts: sun8i: tbs-a711: Enable UART2 (for NEO-6M GPS module) ARM: dts: sunxi: Remove useless pinctrl nodes ARM: dts: sunxi: Remove pinctrl groups setting bias ARM: dts: sunxi: Remove useless address and size cells ARM: dts: sunxi: Conform to DT spec for NAND controller ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'tegra-for-5.2-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt arm64: tegra: Device tree changes for v5.2-rc1 This contains a bunch of changes all across the board. Perhaps the most notable introduction here is support for the Jetson Nano Developer Kit. * tag 'tegra-for-5.2-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: arm64: tegra: Remove regulator hacks on Jetson TX2 arm64: tegra: Enable XUSB on P2771 arm64: tegra: Add XUSB and pad controller on Tegra186 arm64: tegra: Add NVIDIA Jetson Nano Developer Kit support arm64: tegra: smaug: Move PLL power supplies to XUSB pad controller arm64: tegra: jetson-tx1: Move PLL power supplies to XUSB pad controller arm64: tegra: Enable command queue for Tegra186 SDMMC4 arm64: tegra: Fix default tap and trim values arm64: tegra: Add supply for temperature sensor on P2888 arm64: tegra: Enable aconnect, ADMA and AGIC on Jetson TX1 arm64: tegra: Add L2 cache topology to Tegra210 arm64: tegra: Enable CPU idle support for Shield arm64: tegra: Enable CPU idle support for Smaug arm64: tegra: Enable CPU idle support for Jetson TX1 arm64: tegra: Add CPU idle states properties for Tegra210 arm64: tegra: Fix timer node for Tegra210 Signed-off-by:
-
Olof Johansson authored
Merge tag 'tegra-for-5.2-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt ARM: tegra: Device tree changes for v5.2-rc1 This contains a set of changes to move PLL power supplies to the XUSB pad controller, which is necessary to ensure the proper sequencing during boot. Other patches in this set clean up usage of SPDX license identifiers in device tree files as well as add support for the ACTMON hardware on Tegra30. * tag 'tegra-for-5.2-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: ARM: tegra: Add ACTMON support on Tegra30 ARM: tegra: venice2: Move PLL power supplies to XUSB pad controller ARM: tegra: nyan: Move PLL power supplies to XUSB pad controller ARM: tegra: jetson-tk1: Move PLL power supplies to XUSB pad controller ARM: tegra: apalis: Move PLL power supplies to XUSB pad controller ARM: tegra: Remove gratuitous parentheses in SPDX license identifier ARM: tegra: Convert to SPDX license tags for Tegra124 Apalis Signed-off-by:
-
Olof Johansson authored
Merge tag 'omap-for-v5.2/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt Add am335x pinmux defines and start using them This series of changes adds a new pinmux instance defines for am335x, and a new AM33XX_PADCONF macro. And then the rest of the series updates the dts files to use it. The reasons for doing this is the pinmux configuration has been hard to use and read. And we need to do this for eventually for moving to use values. This change is done one machine at a time, and can be easily reverted as needed in case of unexpected trouble. The old macro is still working, and we're planning to keep it around until we eventually change to use * tag 'omap-for-v5.2/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (38 commits) ARM: dts: am335x: wega: Replaced register offsets with defines ARM: dts: am335x: sl50: Replaced register offsets with defines ARM: dts: am335x: shc: Replaced register offsets with defines ARM: dts: am335x: sbc-t335: Replaced register offsets with defines ARM: dts: am335x: sancloud-bbe: Replaced register offsets with defines ARM: dts: am335x: phycore-som: Replaced register offsets with defines ARM: dts: am335x: pepper: Replaced register offsets with defines ARM: dts: am335x: pdu001: Replaced register offsets with defines ARM: dts: am335x: pcm-953: Replaced register offsets with defines ARM: dts: am335x: osd335x-common: Replaced register offsets with defines ARM: dts: am335x: osd3358-sm-red: Replaced register offsets with defines ARM: dts: am335x: nano: Replaced register offsets with defines ARM: dts: am335x: moxa-uc-8100-me-t: Replaced register offsets with defines ARM: dts: am335x: moxa-uc-2101: Replaced register offsets with defines ARM: dts: am335x: moxa-uc-2100-common: Replaced register offsets with defines ARM: dts: am335x: lxm: Replaced register offsets with defines ARM: dts: am335x: igep0033: Replaced register offsets with defines ARM: dts: am335x: icev2: Replaced register offsets with defines ARM: dts: am335x: evmsk: Replaced register offsets with defines ARM: dts: am335x: evm: Replaced register offsets with defines ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'socfpga_dts_updates_for_v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt SoCFPGA DTS updates for v5.2 - Add base support for Agilex platform - Add 'cap-mmc-highspeed' Stratix10 and 32-bit SoCFPGA platform - Increase Stratix10 QSPI support to 100 MHz * tag 'socfpga_dts_updates_for_v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA arm64: dts: stratix10: increase QSPI max frequency to 100MHz arm64: dts: stratix10: enable MMC highspeed support ARM: dts: socfpga: enable MMC highspeed support Signed-off-by:
-
Olof Johansson authored
Merge tag 'ux500-dts-v5.2-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt Ux500 DTS changes for the v5.2 kernel cycle. - This adds the MCDE display controller and some displays. - The Lima MALI-400 driver is added to the kernel, so let's add this block to the Ux500 DTS file. * tag 'ux500-dts-v5.2-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: ARM: dts: Ux500: Add MCDE and Samsung display ARM: dts: ux500: Add Mali-400 Signed-off-by:
-
Olof Johansson authored
Merge tag 'omap-for-v5.2/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt Devicetree changes for omap4 and 5 l4 abe interconnect This series of devicetree changes adds the l4 abe interconnect devices and moves the devices to their right places in the hierarchy similar to what we've already done for most l4 devices earlier. We first add a shared omap4-mcpdm.dtsi to make adding omap4-l4-abe.dtsi easier for the mcpdm changes. And as earlier, in case of unexpected trouble, devices can be probed the old way by moving one device at a time to the old place. This series of changes depends on the ti-sysc driver changes for handling the external optional clocks that the mcpdm relies on, and is based on the related ti-sysc driver changes. Note that this series does not depend on dropping of the leagcy platform data, but I already had those committed along with the ti-sysc driver changes and noticed too late. * tag 'omap-for-v5.2/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (44 commits) ARM: dts: Add l4 abe interconnect hierarchy and ti-sysc data for omap5 ARM: dts: Add l4 abe interconnect hierarchy and ti-sysc data for omap4 ARM: dts: Add common mcpdm dts file for omap4 bus: ti-sysc: Add generic enable/disable functions ARM: OMAP2+: Drop mcspi platform data for omap4 ARM: OMAP2+: Drop uart platform data for dra7 ARM: OMAP2+: Drop gpio platform data for dra7 ARM: OMAP2+: Drop i2c platform data for dra7 ARM: OMAP2+: Drop mmc platform data for dra7 ARM: OMAP2+: Drop uart platform data for omap5 ARM: OMAP2+: Drop gpio platform data for omap5 ARM: OMAP2+: Drop i2c platform data for omap5 ARM: OMAP2+: Drop mmc platform data for omap5 ARM: OMAP2+: Drop uart platform data for am33xx and am43xx ARM: OMAP2+: Drop gpio platform data for am33xx and am43xx ARM: OMAP2+: Drop i2c platform data for am33xx and am43xx ARM: OMAP2+: Drop mmc platform data for am330x and am43xx ARM: OMAP2+: Drop uart platform data for omap4 ARM: OMAP2+: Drop gpio platform data for omap4 ARM: OMAP2+: Drop i2c platform data for omap4 ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'omap-for-v5.2/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt Devicetree changes for omap variants This series of changes configures dra7 pcie x2 lane mode, configures am43xx-epos-evm regulators and keypad wakeup source, and uses standard reset-gpios instead of gpio-reset for n810. We also need to split dra7 dtsi files for properly supporting dra76x and am576 as some of the devices are different such as usb and pruss. * tag 'omap-for-v5.2/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: dra7: Separate AM57 dtsi files dt-binding: arm: omap: Add information for AM5748 ARM: dts: omap2420-n810: Use new CODEC reset pin name ARM: dts: am43xx-epos-evm: Add matrix keypad as wakeup source ARM: dts: am43xx-epos-evm: Keep DCDC3 regulator on in suspend to memory ARM: dts: am43xx-epos-evm: Keep DCDC5 and DCDC6 always on ARM: dts: dra7: Add properties to enable PCIe x2 lane mode Signed-off-by:
-
git://github.com/hisilicon/linux-hisiOlof Johansson authored
ARM64: DT: Hisilicon SoCs DT updates for 5.2 * Hi3660 SoC and related boards: - Added DMA support for the uart nodes - Added the asp DMA controller node - Replaced dma-min-chan with dma-channel-mask to follow the binding * Hi3670 SoC and related boards: - Reused Hi3660 reset to support Hi3670, updated the binding document and added dts node - Reused Hi3660 MMC controller to support Hi3670, updated the binding document and added related nodes to support SD and WiFi for the SoC and hikey970 board - Added UFS controller node * tag 'hisi-arm64-dt-for-5.2' of git://github.com/hisilicon/linux-hisi: arm64: dts: hisilicon: hi3670: Add UFS controller support arm64: dts: hi3660: Fixup unofficial dma-min-chan to dma-channel-mask arm64: dts: hi3660: Add hisi asp dma device arm64: dts: hi3660: Add dma to uart nodes arm64: dts: hisilicon: hikey970: Add SD and WiFi support arm64: dts: hisilicon: hi3670: Add MMC controller support dt-bindings: mmc: Add HI3670 MMC controller binding arm64: dts: hisilicon: hi3670: Add reset controller support dt-bindings: reset: Add HI3670 reset controller binding Signed-off-by: -
https://github.com/Xilinx/linux-xlnxOlof Johansson authored
arm64: dts: zynqmp: DT changes for v5.2 - Align xlnx-zynqmp-clk.h file name and separate binding for clock driver - Add TI quirks to zynqmp boards * tag 'zynqmp-dt-for-v5.2' of https://github.com/Xilinx/linux-xlnx: arm64: zynqmp: dt: Add TI PHY quirk dt-bindings: xilinx: Separate clock binding from firmware doc include: dt-binding: clock: Rename zynqmp header file Signed-off-by:
-
Olof Johansson authored
Merge tag 'samsung-dt64-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt Samsung DTS ARM64 changes for v5.2 1. Use proper clock rates for GSCALER module on TM2 boards. 2. Add clocks for local paths on DECON and GSCALER modules of Exynos5433. 3. Add Slim SecuritySubSystem to Exynos5433. * tag 'samsung-dt64-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: arm64: dts: exynos: Add SlimSSS to Exynos5433 arm64: dts: exynos: add DSD/GSD clocks to DECONs and GSCALERs of Exynos5433 arm64: dts: exynos: configure GSCALER related clocks on TM2 Signed-off-by:
-
Olof Johansson authored
Merge tag 'samsung-dt-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt Samsung DTS ARM changes for v5.2 1. Use proper ADC on Exynos4412. 2. Extend the Exynos5420 Arndale Octa board with: CPU cooling maps, unused regulators, ADC and UHS-I SD card support. Beside that adjust regulators to proper level and add always-on when needed. 3. Extend the Exynos5260: high speed I2C and proper external interrupts. Also fix shared external interrupt line and use better PLL for MMC clocks. 4. Fix audio recording (broken around v5.1) and microphone recording (since v4.14) on Exynos5422 Odroid XU3 boards. 5. Minor cleanups (stdout-path and bootargs). * tag 'samsung-dt-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: exynos: Remove console argument from bootargs ARM: dts: exynos: Use stdout-path property instead of console in bootargs ARM: dts: exynos: Fix spelling mistake of EXYNOS5420 ARM: dts: exynos: Fix audio (microphone) routing on Odroid XU3 ARM: dts: exynos: Always enable necessary APIO_1V8 and ABB_1V8 regulators on Arndale Octa ARM: dts: exynos: Extend the eMMC node on Arndale Octa ARM: dts: exynos: Add support for UHS-I SD cards on Arndale Octa ARM: dts: exynos: Adjust ldo23 and ldo27 to lower levels on Arndale Octa ARM: dts: exynos: Fix audio routing on Odroid XU3 ARM: dts: exynos: Enable ADC on Arndale Octa ARM: dts: exynos: Fix interrupt for shared EINTs on Exynos5260 ARM: dts: exynos: Add interrupts for dedicated EINTs on Exynos5260 ARM: dts: exynos: Add high speed I2C ports for Exynos5260 ARM: dts: exynos: Use bustop PLL as the source for MMC clocks on Exynos5260 ARM: dts: exynos: Order nodes alphabetically in Arndale Octa ARM: dts: exynos: Add CPU cooling on Arndale Octa ARM: dts: exynos: Add unused PMIC regulators on Arndale Octa board ARM: dts: exynos: Use stdout path property on Arndale Octa board ARM: dts: exynos: Document regulator used by ADC on Odroid U3 ARM: dts: exynos: Use ADC for Exynos4x12 on Exynos4412 Signed-off-by:
-
Olof Johansson authored
Merge tag 'stm32-dt-for-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt STM32 DT updates for v5.2, round 1 Highlights: ---------- MPU part: - Add initial support of stm32mp157a-dk1 board: This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Several connections are available on this boards: 4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ... - Add initial support of stm32mp157c-dk2 board: This board is a "super-set" of stm32mp157a-dk1. It embeds a STM32MP157c SOC with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Same connections than stm32mp157a-dk1 board are available. Display panel (otm8009a) and Murata wifi/BT combo is added. - Add and enable SD card support (MMCI variant) on stm32mp157c-ed1/ev1 and on stm32mp157a-dk1/dk2 boards. - Add and enable PMIC support (STPMIC1 chip) on stm32mp157c-ed1/ev1 and on stm32mp157a-dk1/dk2 boards. - Add and enable IPCC mailbox support on stm32mp157c-ed1/ev1 and on stm32mp157a-dk1/dk2 boards. - Add sysconfig clock support on stm32mp157c. - Add romem and temperature calibration support on stm32mp157c. - Add SPDIFRX support on stm32mp157c. - Enable CEC on stm32mp157a-dk1/dk2. MCU part: - Add and enable SD card support (MMCI variant) on stm32h743 eval and disco boards. - Add romem and temperature calibration support on stm32f429 (and so stm32f469). - Enable stm32f769 clock driver * tag 'stm32-dt-for-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits) ARM: dts: stm32: enable cec on stm32mp157a-dk1 board ARM: dts: stm32: add cec pins muxing on stm32mp157 ARM: dts: stm32: add ltdc pins muxing on stm32mp157 ARM: dts: stm32: add I2C sleep pins muxing on stm32mp157 ARM: dts: stm32: add power supply of otm8009a on stm32mp157c-dk2 ARM: dts: stm32: Enable STM32F769 clock driver ARM: dts: stm32: add stpmic1 support on stm32mp157a dk1 board ARM: dts: stm32: add stpmic1 support on stm32mp157c ed1 board ARM: dts: stm32: add spdfirx pins to stm32mp157c ARM: dts: stm32: add spdifrx support on stm32mp157c ARM: dts: stm32: Add romem and temperature calibration on stm32f429 ARM: dts: stm32: Add romem and temperature calibration on stm32mp157c ARM: dts: stm32: Add clock on stm32mp157c syscfg ARM: dts: stm32: enable IPCC mailbox support on STM32MP157a-dk1 ARM: dts: stm32: enable IPCC mailbox support on STM32MP157c-ed1 ARM: dts: stm32: add IPCC mailbox support on STM32MP157c ARM: dts: stm32: add sdmmc1 support on stm32mp157a dk1 board ARM: dts: stm32: add sdmmc1 support on stm32mp157c ed1 board ARM: dts: stm32: add sdmmc1 support on stm32mp157c ARM: dts: stm32: add sdmmc1 support on stm32h743i disco board ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'aspeed-5.2-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt ASPEED device tree updates for 5.2 - RTC and GFX DRM driver went upstream this cycle - Miscellaneous board updates for Facebook and IBM BMCs * tag 'aspeed-5.2-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed: ARM: dts: aspeed: Add RTC node ARM: dts: aspeed: witherspoon: Update BMC partitioning ARM: dts: aspeed: cmm: enable iio-hwmon-adc ARM: dts: aspeed: tiogapass: Enable VUART ARM: dts: aspeed-g5: Add video engine ARM: dts: aspeed: Enable the GFX IP ARM: dts: aspeed-g5: Add resets and clocks to GFX node ARM: dts: aspeed: witherspoon: Enable vhub ARM: dts: aspeed: palmetto: Fix flash_memory region ARM: dts: aspeed: ast2500: Update flash layout Signed-off-by:
-
Olof Johansson authored
Merge tag 'renesas-arm64-dt-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt Renesas ARM64 Based SoC DT Updates for v5.2 * R-Car Gen3 SoC based Salvator-X and Salvator-XS boards - Add GPIO keys support - Sort rwdt node alphabetically * R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs - Use extended audio DMAC register * R-Car M3-W (r8a7796) SoC - Remove unneeded sound #address/size-cells * R-Car M3-N (r8a77965) SoC - Add SSIU support for audio * R-Car E3 (r8a77990) and RZ/G2E (r8a774c0) SoCs - Remove invalid compatible value for CSI40 * R-Car E3 (r8a77990) SoC - Cprrect SPDX license identifier style * R-Car E3 (r8a77990) based Ebisu board - Add BD9571 PMIC with DDR0 backup power config - Correct adv7482 hexadecimal register address - Add GPIO expander * R-Car E3 (r8a77990) based Ebisu and D3 (r8a77995) based Draak boards - Update bootargs to bring them into line with other R-Car Gen3 boards - Enable LVDS1 encoder * R-Car D3 (r8a77995) based Draak board - Correct EthernetAVB phy mode - Enable CAN0 and CAN1 * RZ/G2E (r8a774c0) SoC - Add CANFD support - Correct CPU node style * RZ/G2E (r8a774c0) and RZ/G2M (r8a774a1) SoCs - Add clkp2 clock to CAN nodes * RZ/G2E (r8a774c0) based EK874 board - Add LED, CAN and RTC support * tag 'renesas-arm64-dt-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits) arm64: dts: renesas: salvator-common: Add GPIO keys support arm64: dts: renesas: use extended audio dmac register arm64: dts: renesas: r8a77995: draak: Fix EthernetAVB phy mode to rgmii arm64: dts: renesas: salvator-common: Sort node label arm64: dts: renesas: Update Ebisu and Draak bootargs arm64: dts: renesas: r8a774c0: Add clkp2 clock to CAN nodes arm64: dts: renesas: r8a774c0: Add CANFD support arm64: dts: renesas: r8a774a1: Add clkp2 clock to CAN nodes arm64: dts: renesas: ebisu: Add PMIC DDR0 Backup Power config arm64: dts: renesas: r8a77990-ebisu: Add BD9571 PMIC arm64: dts: renesas: r8a77990: Remove invalid compatible value for CSI40 arm64: dts: renesas: r8a774c0: Remove invalid compatible value for CSI40 arm64: dts: renesas: r8a77995: draak: Enable CAN0, CAN1 arm64: dts: renesas: r8a774c0-cat874: Add RWDT support arm64: dts: renesas: ebisu: Enable VIN5 arm64: dts: renesas: r8a774c0-cat874: Add LEDs support arm64: dts: renesas: r8a774c0-cat874: add RTC support arm64: dts: renesas: cat875: Add CAN support arm64: dts: renesas: r8a774c0: Fix cpu nodes style arm64: dts: renesas: r8a77965: add SSIU support for sound ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'v5.2-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt Core new soc features are hdmi-cec for rk3328, scheduler capacity-values and emmc cleanups for rk3399. New boards are the OrangePi (rk3399) and NanoPi NEO4. Both the OrangePi as well as the NanoPC/Pie family also directly got some additional features added after the boards itself. The Rock960 family (rock960+ficus) got their power-tree cleaned to match the schematics and also got hdmi-audio and their gpu enabled. Mali support also got enabled on the RockPi4 and finally both rk3328-rock64 and rk3328-roc-cc got some additional features. * tag 'v5.2-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits) arm64: dts: rockchip: Decrease emmc-phy's drive impedance on rk3399-puma arm64: dts: rockchip: Define drive-impedance-ohm for RK3399's emmc-phy. arm64: dts: rockchip: Disable DCMDs on RK3399's eMMC controller. arm64: dts: rockchip: Add nanopi4 ethernet phy arm64: dts: rockchip: Add PWM fan for NanoPC-T4 arm64: dts: rockchip: Add the fusb typec manager to rk3399-orangepi arm64: dts: rockchip: Specify vid supply for the rk3399-orangepi compass (AK09911) arm64: dts: rockchip: Fix clock names and add missing supplies for bluetooth on rk3399-orangepi arm64: dts: rockchip: Add 12V DCIN regulator to rk3399-ficus arm64: dts: rockchip: Rename vcc_sys into vcc5v0_sys on rk3399-rock960 arm64: dts: rockchip: Add Nanopi NEO4 initial support arm64: dts: rockchip: enable hdmi audio out for rk3399-rockpro64 arm64: dts: rockchip: Add support for the Orange Pi RK3399 board. arm64: dts: rockchip: enable mali on rock960 boards arm64: dts: rockchip: enable mali on Rock Pi 4 arm64: dts: rockchip: add rk3328-roc-cc cpu-supply entries for all cpu nodes arm64: dts: rockchip: give some life to the rk3328-roc-cc leds arm64: dts: rockchip: add #sound-dai-cells to HDMI of rk3328 arm64: dts: rockchip: add ir-receiver node on rk3328-rock64 arm64: dts: rockchip: add leds node on rk3328-rock64 ... Signed-off-by:
-
Olof Johansson authored
Merge tag 'v5.2-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt Quite a bit of love for the rk3288-veyron chromeos devices and a number of cleanups for rk3288 from that area, hdmi support for the old rk3066 a small rv1108-eglin-r1 cleanup and wifi+hdmi-cec for the tinker board. * tag 'v5.2-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: enable vop0 and hdmi nodes to rk3066a-mk808 ARM: dts: rockchip: add rk3066 hdmi nodes ARM: dts: rockchip: Add device tree for rk3288-veyron-mighty dt-bindings: ARM: dts: rockchip: Add bindings for rk3288-veyron-mighty ARM: dts: rockchip: Add vdd_logic to rk3288-veyron ARM: dts: rockchip: Add dvs-gpios to rk3288-veyron-jerry ARM: dts: rockchip: Add rk3288-veyron-jerry rev 10-15 dt-bindings: ARM: dts: rockchip: Add rk3288-veyron-jerry rev 10-15 ARM: dts: rockchip: Fix gic/efuse sort ordering for rk3288 ARM: dts: rockchip: Enable WiFi on rk3288-tinker ARM: dts: rockchip: add grf reference in rk3288 tsadc node ARM: dts: rockchip: Enable HDMI CEC on rk3288-tinker-s ARM: dts: rockchip: remove disable-wp from rv1108-elgin-r1 emmc node Signed-off-by:
-
Olof Johansson authored
Merge tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt ARM: dts: Amlogic updates for v5.2 - add GPIO line names for odroid-c1 boards - support internal clock measure driver * tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: dts: meson8b: odroidc1: add the GPIO line names ARM: dts: meson8b: add the internal clock measurer ARM: dts: meson8: add the internal clock measurer Signed-off-by:
-
Olof Johansson authored
Merge tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt arm64: dts: Amlogic updates for v5.2 Highlights - new board: SEI Robotics 510, based on S905X2 SoC (G12A) - enable more periphearls for S905X2 based boards * tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: arm64: dts: meson-g12a: Add CMA reserved memory arm64: dts: meson-g12a-x96-max: Enable BT Module arm64: dts: meson-g12a-x96-max: add regulators arm64: dts: meson-g12a-sei510: add regulators arm64: dts: meson-g12a-x96-max: add uart_AO pinctrl arm64: dts: meson-g12a-sei510: add uart_AO pinctrl arm64: dts: meson-g12a-u200: add uart_AO pinctrl arm64: dts: meson: g12a: Add UART A, B & C nodes and pins arm64: dts: meson: g12a: add reset controller arm64: dts: meson: g12a: add uart_ao_a pinctrl arm64: dts: meson: g12a: add pinctrl support controllers arm64: dts: meson: g12a: Add AO Clock + Reset Controller support arm64: dts: meson-gxm-nexbox-a1: Enable USB arm64: dts: meson: g12a: add efuse arm64: dts: meson: g12a: add secure monitor arm64: dts: meson-gxl-s905d-phicomm-n1: add status LED arm64: dts: meson-g12a: Add AO Secure node arm64: dts: Add SEI Robotics SEI510 Board vendor-prefixes: Add prefix for Shenzhen SEI Robotics Co., Ltd Signed-off-by:
-
- 18 Apr, 2019 5 commits
-
-
Chen-Yu Tsai authored
The Bananapi M3 and Cubietruck Plus both have USB OTG ports wired to the SoC and PMIC in the same way, with the N_VBUSEN pin on the PMIC controlling VBUS output, the PMIC's VBUS input for sensing VBUS, and PH11 on the SoC for sensing the ID pin. Enable OTG on both boards. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com>
-
Quentin Schulz authored
The AXP813/818 has a VBUS power input. Add a device node for it, now that we support it. Signed-off-by:
Quentin Schulz <quentin.schulz@bootlin.com> [wens@csie.org: Add commit message] Signed-off-by:
-
Jagan Teki authored
Amarula A64-Relic board by default bound with OV5640 camera, so add support for it with below pin information. - PE13, PE12 via i2c-gpio bitbanging - CLK_CSI_MCLK as external clock - PE1 as external clock pin muxing - ALDO1 as AVDD supply - DLDO3 as DOVDD supply - ELDO3 as DVDD supply - PE14 gpio for reset pin - PE15 gpio for powerdown pin Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Signed-off-by:
-
Jagan Teki authored
Some camera modules have the SoC feeding a master clock to the sensor instead of having a standalone crystal. This clock signal is generated from the clock control unit and output from the CSI MCLK function of pin PE1. Add a pinmux setting for it for camera sensors to reference. Signed-off-by:
-
Dmitry Osipenko authored
Add support for ACTMON on Tegra30. This is used to monitor activity from different components. Based on the collected statistics, the rate at which the external memory needs to be clocked can be derived. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Signed-off-by:
Thierry Reding <treding@nvidia.com>
-
- 17 Apr, 2019 15 commits
-
-
Linus Walleij authored
This adds and updates the device tree nodes for the MCDE display controller and connects the Samsung display to the TVK1281618 user interface board (UIB) so we get nicely working graphics on this reference design. Signed-off-by:Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This adds the Mali-400 block, also known as SGA500 or the Smart Graphics Adapter, to the DBx500 DTS file. All resources and bindings are already in place so this just works. Signed-off-by: -
Maxime Ripard authored
According to the device tree specification, any bus should have a 'bus' node name. Since it isn't the case for us on the DE2 bus, fix that. Signed-off-by: -
Maxime Ripard authored
We try to keep the PIO nodes ordered alphabetically, but this doesn't always work out. Let's fix it. Signed-off-by: -
Maxime Ripard authored
The I7 DTS uses an spdif-out property with an "okay" value. However, that property isn't documented anywhere, and isn't used anywhere either. Remove it. Signed-off-by: -
Maxime Ripard authored
While the USB PHY Device Tree mandates that the name of the ID detect pin should be usb0_id_det-gpios, a significant number of device tree use usb0_id_det-gpio instead. This was functional because the GPIO framework falls back to the gpio suffix that is legacy, but we should fix this. Commit 2c515b0d ("ARM: sunxi: Fix the USB PHY ID detect GPIO properties") was supposed to fix this, but one fell through the cracks. Signed-off-by:
-
Maxime Ripard authored
Some nodes still have pinctrl-names entry, yet they don't have any pinctrl group anymore. Drop them. Signed-off-by: -
Thierry Reding authored
Various regulators were marked as always-on for Jetson TX2. At this point, all of the regulators are properly hooked up, so this workaround is no longer required. Signed-off-by: -
Thierry Reding authored
Enable the relevant pads for XUSB support on P2771-0000 and hook up the USB supply voltage regulators to the ports. Signed-off-by: -
Thierry Reding authored
Adds the XUSB pad and XUSB controllers on Tegra186. Reviewed-by:
JC Kuo <jckuo@nvidia.com> Signed-off-by:
-
Thierry Reding authored
The XUSB pad controller is responsible for supplying power to the PLLs used to drive the various USB, PCI and SATA pads. Move the PLL power supplies from the PCIe and XUSB controllers to the XUSB pad controller to make sure they are available when needed. Signed-off-by: -
Thierry Reding authored
The XUSB pad controller is responsible for supplying power to the PLLs used to drive the various USB, PCI and SATA pads. Move the PLL power supplies from the XUSB controller to the XUSB pad controller to make sure they are available when needed. Signed-off-by: -
Thierry Reding authored
The XUSB pad controller is responsible for supplying power to the PLLs used to drive the various USB, PCI and SATA pads. Move the PLL power supplies from the PCIe and XUSB controllers to the XUSB pad controller to make sure they are available when needed. Signed-off-by: -
Thierry Reding authored
The XUSB pad controller is responsible for supplying power to the PLLs used to drive the various USB, PCI and SATA pads. Move the PLL power supplies from the PCIe and XUSB controllers to the XUSB pad controller to make sure they are available when needed. Signed-off-by: -
Thierry Reding authored
Parentheses in the SPDX license identifier are only used to group sub- expressions. If there's no need for such grouping, the parentheses can be omitted. Reviewed-by:
Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by:
-
