- 29 Jan, 2016 15 commits
-
-
Takashi Iwai authored
commit 030e2c78 upstream. snd_seq_ioctl_remove_events() calls snd_seq_fifo_clear() unconditionally even if there is no FIFO assigned, and this leads to an Oops due to NULL dereference. The fix is just to add a proper NULL check. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mario Kleiner authored
commit 9f660a1c upstream. Without this patch, internal speaker and line-out work, but front headphone output jack stays silent on the Mac Pro 4,1. This code path also gets executed on the MacPro 5,1 due to identical codec SSID, but i don't know if it has any positive or adverse effects there or not. (v2) Implement feedback from Takashi Iwai: Reuse alc889_fixup_mbp_vref and just add a new nid 0x19 for the MacPro 4,1. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by:
-
Xiong Zhang authored
commit 3e6db33a upstream. It takes three minutes to enter into hibernation on some OEM SKL machines and we see many codec spurious response after thaw() opertion. This is because HDA is still in D0 state after freeze() call and pci_pm_freeze/pci_pm_freeze_noirq() don't set D3 hot in pci_bus driver. It seems bios still access HDA when system enter into freeze state, HDA will receive codec response interrupt immediately after thaw() call. Because of this unexpected interrupt, HDA enter into a abnormal state and slow down the system enter into hibernation. In this patch, we put HDA into D3 hot state in azx_freeze_noirq() and put HDA into D0 state in azx_thaw_noirq(). V2: Only apply this fix to SKL+ Fix compile error when CONFIG_PM_SLEEP isn't defined [Yet another fix for CONFIG_PM_SLEEP ifdef and the additional comment by tiwai] Signed-off-by:
Xiong Zhang <xiong.y.zhang@intel.com> Signed-off-by:
-
David Henningsson authored
commit 02f6ff90 upstream. On the internal mic of the Packard Bell DOTS, one channel has an inverted signal. Add a quirk to fix this up. BugLink: https://bugs.launchpad.net/bugs/1523232Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Takashi Iwai authored
commit a74a8216 upstream. rme96 driver needs to reset DAC depending on the sample rate, and this results in resetting to the max volume suddenly. It's because of the missing call of snd_rme96_apply_dac_volume(). However, calling this function right after the DAC reset still may not work, and we need some delay before this call. Since the DAC reset and the procedure after that are performed in the spinlock, we delay the DAC volume restore at the end after the spinlock. Reported-and-tested-by:
Sylvain LABOISNE <maeda1@free.fr> Signed-off-by:
-
Takashi Iwai authored
commit c932b98c upstream. HP ProBook 6550b needs the same pin fixup applied to other HP B-series laptops with docks for making its headphone and dock headphone jacks working properly. We just need to add the codec SSID to the list. Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=191971Signed-off-by:
-
Alexandra Yates authored
commit 5cf92c8b upstream. Adding Intel codename Lewisburg platform device IDs for audio. [rearranged the position by tiwai] Signed-off-by:
Alexandra Yates <alexandra.yates@linux.intel.com> Signed-off-by:
-
Jan Stancek authored
commit 27f972d3 upstream. We encountered a panic on boot in ipmi_si on a dell per320 due to an uninitialized timer as follows. static int smi_start_processing(void *send_info, ipmi_smi_t intf) { /* Try to claim any interrupts. */ if (new_smi->irq_setup) new_smi->irq_setup(new_smi); --> IRQ arrives here and irq handler tries to modify uninitialized timer which triggers BUG_ON(!timer->function) in __mod_timer(). Call Trace: <IRQ> [<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si] [<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si] [<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si] [<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350 [<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si] [<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170 [<ffffffff810f245e>] handle_edge_irq+0xde/0x180 [<ffffffff8100fc59>] handle_irq+0x49/0xa0 [<ffffffff8154643c>] do_IRQ+0x6c/0xf0 [<ffffffff8100ba53>] ret_from_intr+0x0/0x11 /* Set up the timer that drives the interface. */ setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi); The following patch fixes the problem. To: Openipmi-developer@lists.sourceforge.net To: Corey Minyard <minyard@acm.org> CC: linux-kernel@vger.kernel.org Signed-off-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Tony Camuso <tcamuso@redhat.com> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
-
H.J. Lu authored
commit 8c31902c upstream. When decompressing kernel image during x86 bootup, malloc memory for ELF program headers may run out of heap space, which leads to system halt. This patch doubles BOOT_HEAP_SIZE to 64KB. Tested with 32-bit kernel which failed to boot without this patch. Signed-off-by:
H.J. Lu <hjl.tools@gmail.com> Acked-by:
H. Peter Anvin <hpa@zytor.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Mario Kleiner authored
commit 2f0c0b2d upstream. Without the reboot=pci method, the iMac 10,1 simply hangs after printing "Restarting system" at the point when it should reboot. This fixes it. Signed-off-by:
-
Paul Mackerras authored
commit c20875a3 upstream. Currently it is possible for userspace (e.g. QEMU) to set a value for the MSR for a guest VCPU which has both of the TS bits set, which is an illegal combination. The result of this is that when we execute a hrfid (hypervisor return from interrupt doubleword) instruction to enter the guest, the CPU will take a TM Bad Thing type of program interrupt (vector 0x700). Now, if PR KVM is configured in the kernel along with HV KVM, we actually handle this without crashing the host or giving hypervisor privilege to the guest; instead what happens is that we deliver a program interrupt to the guest, with SRR0 reflecting the address of the hrfid instruction and SRR1 containing the MSR value at that point. If PR KVM is not configured in the kernel, then we try to run the host's program interrupt handler with the MMU set to the guest context, which almost certainly causes a host crash. This closes the hole by making kvmppc_set_msr_hv() check for the illegal combination and force the TS field to a safe value (00, meaning non-transactional). Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Ouyang Zhaowei (Charles) authored
commit 6a1f5137 upstream. On a cancelled suspend the vcpu_info location does not change (it's still in the per-cpu area registered by xen_vcpu_setup()). So do not call xen_hvm_init_shared_info() which would make the kernel think its back in the shared info. With the wrong vcpu_info, events cannot be received and the domain will hang after a cancelled suspend. Signed-off-by:
Charles Ouyang <ouyangzhaowei@huawei.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Boris Ostrovsky authored
commit 9c17d965 upstream. Doing so will cause the grant to be unmapped and then, during fault handling, the fault to be mistakenly treated as NUMA hint fault. In addition, even if those maps could partcipate in NUMA balancing, it wouldn't provide any benefit since we are unable to determine physical page's node (even if/when VNUMA is implemented). Marking grant maps' VMAs as VM_IO will exclude them from being part of NUMA balancing. Signed-off-by:
-
Dmitry V. Levin authored
commit 22eab110 upstream. When restarting a syscall with regs->ax == -ERESTART_RESTARTBLOCK, regs->ax is assigned to a restart_syscall number. For x32 tasks, this syscall number must have __X32_SYSCALL_BIT set, otherwise it will be an x86_64 syscall number instead of a valid x32 syscall number. This issue has been there since the introduction of x32. Reported-by: strace/tests/restart_syscall.test Reported-and-tested-by:
Elvira Khabirova <lineprinter0@gmail.com> Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Cc: Elvira Khabirova <lineprinter0@gmail.com> Link: http://lkml.kernel.org/r/20151130215436.GA25996@altlinux.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Willy Tarreau authored
As reported by Sultan Qasim, commit 3822b5c2 ("af_unix: Revert 'lock_interruptible' in stream receive code") was accidently applied at the wrong place in the backport that appeared in 3.10.95, it affected unix_dgram_recvmsg() instead of unix_stream_recvmsg() due to now similar code sections there. The dgram part needs to remain but the stream part needs to be removed. Reported-By:
Sultan Qasim <sultanqasim@gmail.com> Fixes: 3a57e783 (3.10.95) Signed-off-by:
Willy Tarreau <w@1wt.eu>
-
- 23 Jan, 2016 25 commits
-
-
Greg Kroah-Hartman authored
-
Yevgeny Pats authored
commit 23567fd0 upstream. This fixes CVE-2016-0728. If a thread is asked to join as a session keyring the keyring that's already set as its session, we leak a keyring reference. This can be tested with the following program: #include <stddef.h> #include <stdio.h> #include <sys/types.h> #include <keyutils.h> int main(int argc, const char *argv[]) { int i = 0; key_serial_t serial; serial = keyctl(KEYCTL_JOIN_SESSION_KEYRING, "leaked-keyring"); if (serial < 0) { perror("keyctl"); return -1; } if (keyctl(KEYCTL_SETPERM, serial, KEY_POS_ALL | KEY_USR_ALL) < 0) { perror("keyctl"); return -1; } for (i = 0; i < 100; i++) { serial = keyctl(KEYCTL_JOIN_SESSION_KEYRING, "leaked-keyring"); if (serial < 0) { perror("keyctl"); return -1; } } return 0; } If, after the program has run, there something like the following line in /proc/keys: 3f3d898f I--Q--- 100 perm 3f3f0000 0 0 keyring leaked-keyring: empty with a usage count of 100 * the number of times the program has been run, then the kernel is malfunctioning. If leaked-keyring has zero usages or has been garbage collected, then the problem is fixed. Reported-by:
Yevgeny Pats <yevgeny@perception-point.io> Signed-off-by:
David Howells <dhowells@redhat.com> Acked-by:
Don Zickus <dzickus@redhat.com> Acked-by:
Prarit Bhargava <prarit@redhat.com> Acked-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
David Howells authored
commit b4a1b4f5 upstream. This fixes CVE-2015-7550. There's a race between keyctl_read() and keyctl_revoke(). If the revoke happens between keyctl_read() checking the validity of a key and the key's semaphore being taken, then the key type read method will see a revoked key. This causes a problem for the user-defined key type because it assumes in its read method that there will always be a payload in a non-revoked key and doesn't check for a NULL pointer. Fix this by making keyctl_read() check the validity of a key after taking semaphore instead of before. I think the bug was introduced with the original keyrings code. This was discovered by a multithreaded test program generated by syzkaller (http://github.com/google/syzkaller). Here's a cleaned up version: #include <sys/types.h> #include <keyutils.h> #include <pthread.h> void *thr0(void *arg) { key_serial_t key = (unsigned long)arg; keyctl_revoke(key); return 0; } void *thr1(void *arg) { key_serial_t key = (unsigned long)arg; char buffer[16]; keyctl_read(key, buffer, 16); return 0; } int main() { key_serial_t key = add_key("user", "%", "foo", 3, KEY_SPEC_USER_KEYRING); pthread_t th[5]; pthread_create(&th[0], 0, thr0, (void *)(unsigned long)key); pthread_create(&th[1], 0, thr1, (void *)(unsigned long)key); pthread_create(&th[2], 0, thr0, (void *)(unsigned long)key); pthread_create(&th[3], 0, thr1, (void *)(unsigned long)key); pthread_join(th[0], 0); pthread_join(th[1], 0); pthread_join(th[2], 0); pthread_join(th[3], 0); return 0; } Build as: cc -o keyctl-race keyctl-race.c -lkeyutils -lpthread Run as: while keyctl-race; do :; done as it may need several iterations to crash the kernel. The crash can be summarised as: BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 IP: [<ffffffff81279b08>] user_read+0x56/0xa3 ... Call Trace: [<ffffffff81276aa9>] keyctl_read_key+0xb6/0xd7 [<ffffffff81277815>] SyS_keyctl+0x83/0xe0 [<ffffffff815dbb97>] entry_SYSCALL_64_fastpath+0x12/0x6f Reported-by:
-
David Howells authored
commit f05819df upstream. The following sequence of commands: i=`keyctl add user a a @s` keyctl request2 keyring foo bar @t keyctl unlink $i @s tries to invoke an upcall to instantiate a keyring if one doesn't already exist by that name within the user's keyring set. However, if the upcall fails, the code sets keyring->type_data.reject_error to -ENOKEY or some other error code. When the key is garbage collected, the key destroy function is called unconditionally and keyring_destroy() uses list_empty() on keyring->type_data.link - which is in a union with reject_error. Subsequently, the kernel tries to unlink the keyring from the keyring names list - which oopses like this: BUG: unable to handle kernel paging request at 00000000ffffff8a IP: [<ffffffff8126e051>] keyring_destroy+0x3d/0x88 ... Workqueue: events key_garbage_collector ... RIP: 0010:[<ffffffff8126e051>] keyring_destroy+0x3d/0x88 RSP: 0018:ffff88003e2f3d30 EFLAGS: 00010203 RAX: 00000000ffffff82 RBX: ffff88003bf1a900 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000000003bfc6901 RDI: ffffffff81a73a40 RBP: ffff88003e2f3d38 R08: 0000000000000152 R09: 0000000000000000 R10: ffff88003e2f3c18 R11: 000000000000865b R12: ffff88003bf1a900 R13: 0000000000000000 R14: ffff88003bf1a908 R15: ffff88003e2f4000 ... CR2: 00000000ffffff8a CR3: 000000003e3ec000 CR4: 00000000000006f0 ... Call Trace: [<ffffffff8126c756>] key_gc_unused_keys.constprop.1+0x5d/0x10f [<ffffffff8126ca71>] key_garbage_collector+0x1fa/0x351 [<ffffffff8105ec9b>] process_one_work+0x28e/0x547 [<ffffffff8105fd17>] worker_thread+0x26e/0x361 [<ffffffff8105faa9>] ? rescuer_thread+0x2a8/0x2a8 [<ffffffff810648ad>] kthread+0xf3/0xfb [<ffffffff810647ba>] ? kthread_create_on_node+0x1c2/0x1c2 [<ffffffff815f2ccf>] ret_from_fork+0x3f/0x70 [<ffffffff810647ba>] ? kthread_create_on_node+0x1c2/0x1c2 Note the value in RAX. This is a 32-bit representation of -ENOKEY. The solution is to only call ->destroy() if the key was successfully instantiated. Reported-by:
-
David Howells authored
commit 94c4554b upstream. There appears to be a race between: (1) key_gc_unused_keys() which frees key->security and then calls keyring_destroy() to unlink the name from the name list (2) find_keyring_by_name() which calls key_permission(), thus accessing key->security, on a key before checking to see whether the key usage is 0 (ie. the key is dead and might be cleaned up). Fix this by calling ->destroy() before cleaning up the core key data - including key->security. Reported-by:
Petr Matousek <pmatouse@redhat.com> Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit 3822b5c2 ] With b3ca9b02, the AF_UNIX SOCK_STREAM receive code was changed from using mutex_lock(&u->readlock) to mutex_lock_interruptible(&u->readlock) to prevent signals from being delayed for an indefinite time if a thread sleeping on the mutex happened to be selected for handling the signal. But this was never a problem with the stream receive code (as opposed to its datagram counterpart) as that never went to sleep waiting for new messages with the mutex held and thus, wouldn't cause secondary readers to block on the mutex waiting for the sleeping primary reader. As the interruptible locking makes the code more complicated in exchange for no benefit, change it back to using mutex_lock. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 5233252f ] Signed-off-by:
-
WANG Cong authored
[ Upstream commit 09ccfd23 ] Reported-by:
Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 248be83d ] In a low memory situation the following kernel oops occurs: Unable to handle kernel NULL pointer dereference at virtual address 00000050 pgd = 8490c000 [00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: CPU: 0 Not tainted (3.4-at16 #9) PC is at skb_put+0x10/0x98 LR is at sh_eth_poll+0x2c8/0xa10 pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113 sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4 r10: 0000003f r9 : 000005ea r8 : 00000000 r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180 r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 4248c059 DAC: 00000015 Process klogd (pid: 2046, stack limit = 0x84eb02e8) [...] This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left NULL but sh_eth_rx() later uses it without checking. Add such check... Reported-by:
Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 79462ad0 ] 郭永刚 reported that one could simply crash the kernel as root by using a simple program: int socket_fd; struct sockaddr_in addr; addr.sin_port = 0; addr.sin_addr.s_addr = INADDR_ANY; addr.sin_family = 10; socket_fd = socket(10,3,0x40000000); connect(socket_fd , &addr,16); AF_INET, AF_INET6 sockets actually only support 8-bit protocol identifiers. inet_sock's skc_protocol field thus is sized accordingly, thus larger protocol identifiers simply cut off the higher bits and store a zero in the protocol fields. This could lead to e.g. NULL function pointer because as a result of the cut off inet_num is zero and we call down to inet_autobind, which is NULL for raw sockets. kernel: Call Trace: kernel: [<ffffffff816db90e>] ? inet_autobind+0x2e/0x70 kernel: [<ffffffff816db9a4>] inet_dgram_connect+0x54/0x80 kernel: [<ffffffff81645069>] SYSC_connect+0xd9/0x110 kernel: [<ffffffff810ac51b>] ? ptrace_notify+0x5b/0x80 kernel: [<ffffffff810236d8>] ? syscall_trace_enter_phase2+0x108/0x200 kernel: [<ffffffff81645e0e>] SyS_connect+0xe/0x10 kernel: [<ffffffff81779515>] tracesys_phase2+0x84/0x89 I found no particular commit which introduced this problem. CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by:
郭永刚 <guoyonggang@360.cn> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9470e24f ] SCTP is lacking proper np->opt cloning at accept() time. TCP and DCCP use ipv6_dup_options() helper, do the same in SCTP. We might later factorize this code in a common helper to avoid future mistakes. Reported-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 01ce63c9 ] Dmitry Vyukov reported that SCTP was triggering a WARN on socket destroy related to disabling sock timestamp. When SCTP accepts an association or peel one off, it copies sock flags but forgot to call net_enable_timestamp() if a packet timestamping flag was copied, leading to extra calls to net_disable_timestamp() whenever such clones were closed. The fix is to call net_enable_timestamp() whenever we copy a sock with that flag on, like tcp does. Reported-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
-
Pavel Machek authored
[ Upstream commit f2a3771a ] atl1c driver is doing order-4 allocation with GFP_ATOMIC priority. That often breaks networking after resume. Switch to GFP_KERNEL. Still not ideal, but should be significantly better. atl1c_setup_ring_resources() is called from .open() function, and already uses GFP_KERNEL, so this change is safe. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Acked-by:
Michal Hocko <mhocko@suse.com> Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 6a61d4db ] Parameters were updated only if the kernel was unable to find the tunnel with the new parameters, ie only if core pamareters were updated (keys, addr, link, type). Now it's possible to update ttl, hoplimit, flowinfo and flags. Fixes: c12b395a ("gre: Support GRE over IPv6") Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Ben Hutchings authored
commit 5377adb0 upstream. usb_parse_ss_endpoint_companion() now decodes the burst multiplier correctly in order to check that it's <= 3, but still uses the wrong expression if warning that it's > 3. Fixes: ff30cbc8 ("usb: Use the USB_SS_MULT() macro to get the ...") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Alexey Khoroshilov authored
commit f9fa1887 upstream. qset_fill_page_list() do not check for dma mapping errors. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Alan Stern authored
commit ad87e032 upstream. Some USB device / host controller combinations seem to have problems with Link Power Management. For example, Steinar found that his xHCI controller wouldn't handle bandwidth calculations correctly for two video cards simultaneously when LPM was enabled, even though the bus had plenty of bandwidth available. This patch introduces a new quirk flag for devices that should remain disabled for LPM, and creates quirk entries for Steinar's devices. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Steinar H. Gunderson <sgunderson@bigfoot.com> Signed-off-by:
-
Konstantin Shkolnyy authored
commit 7c90e610 upstream. CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID and completely different from CP210x devices. Signed-off-by:
Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Jonas Jonsson authored
commit f33a7f72 upstream. Some modems, such as the Telit UE910, are using an Infineon Flash Loader utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC Data). The latter can be used as a serial interface to upgrade the firmware of the modem. However, that isn't possible when the cdc-acm driver takes control of the device. The following is an explanation of the behaviour by Daniele Palmas during discussion on linux-usb. "This is what happens when the device is turned on (without modifying the drivers): [155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci [155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11 [155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041 [155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device This is the flashing device that is caught by the cdc-acm driver. Once the ttyACM appears, the application starts sending a magic string (simple write on the file descriptor) to keep the device in flashing mode. If this magic string is not properly received in a certain time interval, the modem goes on in normal operative mode: [155493.748094] usb 1-3: USB disconnect, device number 27 [155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci [155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021 [155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM [155495.059989] usb 1-3: Manufacturer: Telit [155495.059992] usb 1-3: SerialNumber: 359658044004697 [155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device [155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device [155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device [155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device [155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device [155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device [155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14 Using the cdc-acm driver, the string, though being sent in the same way than using the usb-serial-simple driver (I can confirm that the data is passing properly since I used an hw usb sniffer), does not make the device to stay in flashing mode." Signed-off-by:
Jonas Jonsson <jonas@ludd.ltu.se> Tested-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Jeff Layton authored
commit c812012f upstream. If we pass in an empty nfs_fattr struct to nfs_update_inode, it will (correctly) not update any of the attributes, but it then clears the NFS_INO_INVALID_ATTR flag, which indicates that the attributes are up to date. Don't clear the flag if the fattr struct has no valid attrs to apply. Reviewed-by:
Steve French <steve.french@primarydata.com> Signed-off-by:
Jeff Layton <jeff.layton@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Benjamin Coddington authored
commit c68a027c upstream. If clp->cl_cb_ident is zero, then nfs_cb_idr_remove_locked() skips removing it when the nfs_client is freed. A decoding or server bug can then find and try to put that first nfs_client which would lead to a crash. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Fixes: d6870312 ("nfs4client: convert to idr_alloc()") Signed-off-by:
-
Stefan Richter authored
commit 100ceb66 upstream. Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo controllers: Often or even most of the time, the controller is initialized with the message "added OHCI v1.10 device as card 0, 4 IR + 0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts (IT contexts), applications like audio output are impossible. However, OHCI-1394 demands that at least 4 IT contexts are implemented by the link layer controller, and indeed JMicron JMB38x do implement four of them. Only their IsoXmitIntMask register is unreliable at early access. With my own JMB381 single function controller I found: - I can reproduce the problem with a lower probability than Craig's. - If I put a loop around the section which clears and reads IsoXmitIntMask, then either the first or the second attempt will return the correct initial mask of 0x0000000f. I never encountered a case of needing more than a second attempt. - Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet) before the first write, the subsequent read will return the correct result. - If I merely ignore a wrong read result and force the known real result, later isochronous transmit DMA usage works just fine. So let's just fix this chip bug up by the latter method. Tested with JMB381 on kernel 3.13 and 4.3. Since OHCI-1394 generally requires 4 IT contexts at a minium, this workaround is simply applied whenever the initial read of IsoXmitIntMask returns 0, regardless whether it's a JMicron chip or not. I never heard of this issue together with any other chip though. I am not 100% sure that this fix works on the OHCI-1394 part of JMB380 and JMB388 combo controllers exactly the same as on the JMB381 single- function controller, but so far I haven't had a chance to let an owner of a combo chip run a patched kernel. Strangely enough, IsoRecvIntMask is always reported correctly, even though it is probed right before IsoXmitIntMask. Reported-by: Clifford Dunn Reported-by:
Craig Moore <craig.moore@qenos.com> Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
Daeho Jeong authored
commit 4327ba52 upstream. If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the journaling will be aborted first and the error number will be recorded into JBD2 superblock and, finally, the system will enter into the panic state in "errors=panic" option. But, in the rare case, this sequence is little twisted like the below figure and it will happen that the system enters into panic state, which means the system reset in mobile environment, before completion of recording an error in the journal superblock. In this case, e2fsck cannot recognize that the filesystem failure occurred in the previous run and the corruption wouldn't be fixed. Task A Task B ext4_handle_error() -> jbd2_journal_abort() -> __journal_abort_soft() -> __jbd2_journal_abort_hard() | -> journal->j_flags |= JBD2_ABORT; | | __ext4_abort() | -> jbd2_journal_abort() | | -> __journal_abort_soft() | | -> if (journal->j_flags & JBD2_ABORT) | | return; | -> panic() | -> jbd2_journal_update_sb_errno() Tested-by:
Hobin Woo <hobin.woo@samsung.com> Signed-off-by:
Daeho Jeong <daeho.jeong@samsung.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Filipe Manana authored
commit 1d512cb7 upstream. If we are using the NO_HOLES feature, we have a tiny time window when running delalloc for a nodatacow inode where we can race with a concurrent link or xattr add operation leading to a BUG_ON. This happens because at run_delalloc_nocow() we end up casting a leaf item of type BTRFS_INODE_[REF|EXTREF]_KEY or of type BTRFS_XATTR_ITEM_KEY to a file extent item (struct btrfs_file_extent_item) and then analyse its extent type field, which won't match any of the expected extent types (values BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]) and therefore trigger an explicit BUG_ON(1). The following sequence diagram shows how the race happens when running a no-cow dellaloc range [4K, 8K[ for inode 257 and we have the following neighbour leafs: Leaf X (has N items) Leaf Y [ ... (257 INODE_ITEM 0) (257 INODE_REF 256) ] [ (257 EXTENT_DATA 8192), ... ] slot N - 2 slot N - 1 slot 0 (Note the implicit hole for inode 257 regarding the [0, 8K[ range) CPU 1 CPU 2 run_dealloc_nocow() btrfs_lookup_file_extent() --> searches for a key with value (257 EXTENT_DATA 4096) in the fs/subvol tree --> returns us a path with path->nodes[0] == leaf X and path->slots[0] == N because path->slots[0] is >= btrfs_header_nritems(leaf X), it calls btrfs_next_leaf() btrfs_next_leaf() --> releases the path hard link added to our inode, with key (257 INODE_REF 500) added to the end of leaf X, so leaf X now has N + 1 keys --> searches for the key (257 INODE_REF 256), because it was the last key in leaf X before it released the path, with path->keep_locks set to 1 --> ends up at leaf X again and it verifies that the key (257 INODE_REF 256) is no longer the last key in the leaf, so it returns with path->nodes[0] == leaf X and path->slots[0] == N, pointing to the new item with key (257 INODE_REF 500) the loop iteration of run_dealloc_nocow() does not break out the loop and continues because the key referenced in the path at path->nodes[0] and path->slots[0] is for inode 257, its type is < BTRFS_EXTENT_DATA_KEY and its offset (500) is less then our delalloc range's end (8192) the item pointed by the path, an inode reference item, is (incorrectly) interpreted as a file extent item and we get an invalid extent type, leading to the BUG_ON(1): if (extent_type == BTRFS_FILE_EXTENT_REG || extent_type == BTRFS_FILE_EXTENT_PREALLOC) { (...) } else if (extent_type == BTRFS_FILE_EXTENT_INLINE) { (...) } else { BUG_ON(1) } The same can happen if a xattr is added concurrently and ends up having a key with an offset smaller then the delalloc's range end. So fix this by skipping keys with a type smaller than BTRFS_EXTENT_DATA_KEY. Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 602dd62d ] Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets. We need to call inet6_destroy_sock() to properly release inet6 specific fields. Reported-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
