When we fail to add/delete MAC filters in the VF, the print doesn't
distinguish between the two. Fix that by printing whether or not we
failed to add/delete the MAC filter respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

These queue variables are being assigned values that are type u16.
Change the local variables to match these types. Since these
represent queue counts, they should never be negative.
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to use some of the VF resources definition in the SR-IOV specific
virtchnl header file, this patch moves applicable code to
ice_virtchnl_pf.h file accordingly... and they should have been defined in
the destination file originally.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we use the ICE_MBXQ_LEN for both the Mailbox send and receive
queues that are used to communicate with VFs. This is fine for the send
queue because the PF driver will lock the queue for every single send,
but for the Mailbox receive queue every VF is posting to its Mailbox
send queue and the hardware is then handing the message to the PF on its
Mailbox receive queue. This becomes a problem with many VFs because it
seems to overburden the Mailbox receive queue on the PF. Fix this by
increasing the Mailbox receive queue for the PF to 512 entries.

The number 512 was determined based on the number of VFs supported by
the device. We can have a total of 256 VFs so in the worst case this
allows the VFs to put 2 messages in the PFs Mailbox receive queue at the
same time.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there are a couple places where the VF is waiting too long when
checking the status of registers. This is causing the AVF driver to
spin for longer than necessary in the __IAVF_STARTUP state. Sometimes
it causes the AVF to go into the __IAVF_COMM_FAILED, which may retrigger
the __IAVF_STARTUP state. Try to reduce the chance of this happening by
removing unnecessary wait times in VF bringup/resets.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Register access for GLINT_DYN_CTL and GLINT_VECT2FUNC should be within
the PF space and not the absolute device space.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During rebuild ice_ena_vsi() is called to recover the VSI state.
This function assumes the PF VSI is always to be enabled, however,
it's possible that during reset/rebuild the interface can be
brought down.  If this occurs, we can attempt to bring up the PF
VSI on a downed interface which can lead to various crashes. If
the interface is not running, do not bring up the associated VSI.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, the hardware will hand us a receive descriptor
which has no data attached, but is otherwise valid. The receive code was
improperly ignoring these descriptors, which result in an infinite loop.

To fix this, change the receive code to process all descriptors,
regardless of the size of the associated data. Add checks to the
memory-handling functions to allow for zero size.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the set local MIB AQ call failures in the DCB rebuild path
by setting the defaults for the ETS recommended DCB configuration. Also,
willing bits for the DCB configuration needs to be set correctly. Resets
works fine in IEEE mode as the ETS recommended DCB configuration is
populated but not in CEE mode.
Without this patch, PFR causes the kernel hang in CEE mode.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when busy polling is enabled we aren't setting/enabling
WB_ON_ITR in the driver. This doesn't break the driver, but it does
cause issues. If we don't enable WB_ON_ITR mode we will still get
write-backs from hardware during polling when a cache line has been
filled, but if a cache line is not filled we will not get the
write-back because WB_ON_ITR is not set. Fix this by enabling
WB_ON_ITR in the driver when interrupts are disabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When ETHTOOL_GLINKSETTINGS is defined get pause param pause->autoneg
reports SW configured setting, however when not defined get pause param
pause->autoneg reports the link status. Set pause param needs to compare
pause->autoneg with the same source as get pause param to block the user
from changing autoneg with the set pause param option, or the user
may be incorrectly blocked from changing Rx|Tx pause settings.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch restructures how VFs are configured, and resources allocated.
Instead of freeing resources that were never allocated, and resetting
empty VFs that have never been created - the new flow will just allocate
resources for number of requested VFs based on the availability.

During VFs initialization process, global interrupt is disabled, and
rearmed after getting MSIX vectors for VFs. This allows immediate mailbox
communications, instead of delaying it till later and VFs.
PF communications resulted to using polling instead of actual interrupt.
The issue manifested when creating higher number of VFs (128 VFs) per PF.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we divide budget by the number of Rx queues per Rx ring
container in ice_napi_poll even if there is only 1. This is an
unnecessary divide for the normal case of 1 Rx ring per Rx ring
container. Fix this by using an unlikely() call in the case where we
actually need to divide.

Also, we will always set budget_per_ring even if there are no Rx rings
in the Rx ring container so we don't need to initialize it to 0.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently in ice_get_tx_pending we try to read a Tx ring's tail. This is
then compared with the software based head (next_to_clean) to determine
if we have pending work. This will never work because reading of the Tx
ring's tail is no longer supported. Fix this by using the software based
tail (next_to_use) to determine if there is pending work.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge tag 'wireless-drivers-next-for-davem-2019-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.4

First set of patches for 5.4.

Major changes:

brcmfmac

* enable 160 MHz channel support

rt2x00

* add support for PLANEX GW-USMicroN USB device

rtw88

* add Bluetooth coexistance support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: support per endpoint auth and asconf flags

This patchset mostly does 3 things:

  1. add per endpint asconf flag and use asconf flag properly
     and add SCTP_ASCONF_SUPPORTED sockopt.
  2. use auth flag properly and add SCTP_AUTH_SUPPORTED sockopt.
  3. remove the 'global feature switch' to discard chunks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The netns sctp feature flags shouldn't work as a global switch,
which is mostly like a firewall/netfilter's job. Also, it will
break asoc as it discard or accept chunks incorrectly when net
sctp.x_enable is changed after the asoc is created.

Since each type of chunk's processing function will check the
corresp asoc's feature flag, this 'global switch' should be
removed, and net sctp.x_enable will only work as the default
feature flags for the future sctp sockets/endpoints.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP_AUTH_SUPPORTED sockopt is used to set enpoint's auth
flag. With this feature, each endpoint will have its own
flag for its future asoc's auth_capable, instead of netns
auth flag.

Note that when both ep's auth_enable is enabled, endpoint
auth related data should be initialized. If asconf_enable
is also set, SCTP_CID_ASCONF/SCTP_CID_ASCONF_ACK should
be added into auth_chunk_list.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to factor out sctp_auth_init and sctp_auth_free
functions, and sctp_auth_init will also be used in the next
patch for SCTP_AUTH_SUPPORTED sockopt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp has per endpoint auth flag and per asoc auth flag, and
the asoc one should be checked when coming to asoc and the
endpoint one should be checked when coming to endpoint.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP_ASCONF_SUPPORTED sockopt is used to set enpoint's asconf
flag. With this feature, each endpoint will have its own flag
for its future asoc's asconf_capable, instead of netns asconf
flag.

Note that when both ep's asconf_enable and auth_enable are
enabled, SCTP_CID_ASCONF and SCTP_CID_ASCONF_ACK should be
added into auth_chunk_list.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

asconf chunks should be dropped when the asoc doesn't support
asconf feature.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

asoc->peer.asconf_capable is to be set during handshake, and its
value should be initialized to 0. net->sctp.addip_noauth will be
checked in sctp_process_init when processing INIT_ACK on client
and COOKIE_ECHO on server.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to make addip/asconf flag per endpoint,
and its value is initialized by the per netns flag,
net->sctp.addip_enable.

It also replaces the checks of net->sctp.addip_enable
with ep->asconf_enable in some places.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer members of an object with static storage duration, if not
explicitly initialized, will be initialized to a NULL pointer. The
net namespace API checks if this pointer is not NULL before using it,
it are safe to remove the function.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
Fix problems with using ns plugin

Recent changes to plugin architecture broke some of the tests when running tdc
without specifying a test group. Fix tests incompatible with ns plugin and
modify tests to not reuse interface name of ns veth interface for dummy
interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Concurrent tests use several commands to update rules in parallel: 'find'
prints names of batch files in tmp directory and pipes result to 'xargs'
which runs instance of tc per batch file in parallel. This breaks when used
with ns plugin that adds 'ip netns exec $NS' prefix to the command, which
causes only first command in pipe to be executed in namespace:

=====> Test e41d: Add 1M flower filters with 10 parallel tc instances
-----> prepare stage
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [/bin/mkdir tmp] list [['/bin/mkdir', 'tmp']]
adjust_command:  return command [ip netns exec tcut /bin/mkdir tmp]
command "ip netns exec tcut /bin/mkdir tmp"
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [/sbin/tc qdisc add dev ens1f0 ingress] list [['/sbin/tc', 'qdisc', 'add', 'dev', 'ens1f0', 'ingress']]
adjust_command:  return command [ip netns exec tcut /sbin/tc qdisc add dev ens1f0 ingress]
command "ip netns exec tcut /sbin/tc qdisc add dev ens1f0 ingress"
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [./tdc_multibatch.py ens1f0 tmp 100000 10 add] list [['./tdc_multibatch.py', 'ens1f0', 'tmp', '100000', '10', 'add']]
adjust_command:  return command [ip netns exec tcut ./tdc_multibatch.py ens1f0 tmp 100000 10 add]
command "ip netns exec tcut ./tdc_multibatch.py ens1f0 tmp 100000 10 add"
-----> execute stage
ns/SubPlugin.adjust_command
adjust_command:  stage is execute; inserting netns stuff in command [find tmp/add* -print | xargs -n 1 -P 10 /sbin/tc -b] list [['find', 'tmp/add*', '-print', '|', 'xargs', '-n', '1', '-P', '10', '/sbin/tc', '-b']
]
adjust_command:  return command [ip netns exec tcut find tmp/add* -print | xargs -n 1 -P 10 /sbin/tc -b]
command "ip netns exec tcut find tmp/add* -print | xargs -n 1 -P 10 /sbin/tc -b"
exit: 123
exit: 0
Cannot find device "ens1f0"
Cannot find device "ens1f0"
Command failed tmp/add_0:1
Command failed tmp/add_1:1
Cannot find device "ens1f0"
Command failed tmp/add_2:1
Cannot find device "ens1f0"
Command failed tmp/add_4:1
Cannot find device "ens1f0"
Command failed tmp/add_3:1
Cannot find device "ens1f0"
Command failed tmp/add_5:1
Cannot find device "ens1f0"
Command failed tmp/add_6:1
Cannot find device "ens1f0"
Command failed tmp/add_8:1
Cannot find device "ens1f0"
Command failed tmp/add_7:1
Cannot find device "ens1f0"
Command failed tmp/add_9:1

Fix the issue by executing whole compound command in namespace by wrapping
it in 'bash -c' invocation.

Fixes: 489ce2f4 ("tc-testing: Restore original behaviour for namespaces in tdc")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A lot of tests reuse $DEV1 veth name for naming dummy device. This causes
problem when tdc is invoked without specifying a test group and tries to
execute all tests. In this case tdc instantiates ns plugin, which creates
veth pair once before running tests. However, if any of the tests that
reuse $DEV1 run before test that depend on ns plugin, it will delete $DEV1
as a part of teardown section:

=====> Test 3b88: Delete ingress qdisc twice                                                                                                                                                             [3770/41080]
-----> prepare stage
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [/sbin/ip link add dev v0p1 type dummy || /bin/true] list [['/sbin/ip', 'link', 'add', 'dev', 'v0p1', 'type', 'dummy', '||', '/bin/true']]
adjust_command:  return command [ip netns exec tcut /sbin/ip link add dev v0p1 type dummy || /bin/true]
command "ip netns exec tcut /sbin/ip link add dev v0p1 type dummy || /bin/true"
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [/sbin/tc qdisc add dev v0p1 ingress] list [['/sbin/tc', 'qdisc', 'add', 'dev', 'v0p1', 'ingress']]
adjust_command:  return command [ip netns exec tcut /sbin/tc qdisc add dev v0p1 ingress]
command "ip netns exec tcut /sbin/tc qdisc add dev v0p1 ingress"
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [/sbin/tc qdisc del dev v0p1 ingress] list [['/sbin/tc', 'qdisc', 'del', 'dev', 'v0p1', 'ingress']]
adjust_command:  return command [ip netns exec tcut /sbin/tc qdisc del dev v0p1 ingress]
command "ip netns exec tcut /sbin/tc qdisc del dev v0p1 ingress"
-----> execute stage
ns/SubPlugin.adjust_command
adjust_command:  stage is execute; inserting netns stuff in command [/sbin/tc qdisc del dev v0p1 ingress] list [['/sbin/tc', 'qdisc', 'del', 'dev', 'v0p1', 'ingress']]
adjust_command:  return command [ip netns exec tcut /sbin/tc qdisc del dev v0p1 ingress]
command "ip netns exec tcut /sbin/tc qdisc del dev v0p1 ingress"
-----> verify stage
ns/SubPlugin.adjust_command
adjust_command:  stage is verify; inserting netns stuff in command [/sbin/tc qdisc show dev v0p1] list [['/sbin/tc', 'qdisc', 'show', 'dev', 'v0p1']]
adjust_command:  return command [ip netns exec tcut /sbin/tc qdisc show dev v0p1]
command "ip netns exec tcut /sbin/tc qdisc show dev v0p1"
-----> teardown stage
ns/SubPlugin.adjust_command
adjust_command:  stage is teardown; inserting netns stuff in command [/sbin/ip link del dev v0p1 type dummy] list [['/sbin/ip', 'link', 'del', 'dev', 'v0p1', 'type', 'dummy']]
adjust_command:  return command [ip netns exec tcut /sbin/ip link del dev v0p1 type dummy]
command "ip netns exec tcut /sbin/ip link del dev v0p1 type dummy"

After this ns-dependent tests will fail because dev doesn't exist:

=====> Test 901f: Add fw filter with prio at 32-bit maxixum
-----> prepare stage
ns/SubPlugin.adjust_command
adjust_command:  stage is setup; inserting netns stuff in command [/sbin/tc qdisc add dev v0p1 ingress] list [['/sbin/tc', 'qdisc', 'add', 'dev', 'v0p1', 'ingress']]
adjust_command:  return command [ip netns exec tcut /sbin/tc qdisc add dev v0p1 ingress]
command "ip netns exec tcut /sbin/tc qdisc add dev v0p1 ingress"

-----> prepare stage *** Could not execute: "$TC qdisc add dev $DEV1 ingress"

-----> prepare stage *** Error message: "Cannot find device "v0p1"
"
returncode 1; expected [0]

-----> prepare stage *** Aborting test run.

<_io.BufferedReader name=3> *** stdout ***

<_io.BufferedReader name=5> *** stderr ***
"-----> prepare stage" did not complete successfully
Exception <class '__main__.PluginMgrTestFail'> ('setup', None, '"-----> prepare stage" did not complete successfully') (caught in test_runner, running test 477 901f Add fw filter with prio at 32-bit maxixum stage
setup)
---------------
traceback
  File "./tdc.py", line 371, in test_runner
    res = run_one_test(pm, args, index, tidx)
  File "./tdc.py", line 272, in run_one_test
    prepare_env(args, pm, 'setup', "-----> prepare stage", tidx["setup"])
  File "./tdc.py", line 247, in prepare_env
    '"{}" did not complete successfully'.format(prefix))
---------------

Fix the issue by introducing standalone $DUMMY config variable and
substitute all usage of $DEV1 in tests that don't depend on ns plugin.

Fixes: 489ce2f4 ("tc-testing: Restore original behaviour for namespaces in tdc")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix accessing skb after napi_gro_receive which is caused by
commit 47922fcd ("r8152: support skb_add_rx_frag").

Fixes: 47922fcd ("r8152: support skb_add_rx_frag")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: realtek: support NBase-T MMD EEE registers on RTL8125

Add missing EEE-related constants, including the new MMD EEE registers
for NBase-T / 802.3bz. Based on that emulate the new 802.3bz MMD EEE
registers for 2.5Gbps EEE on RTL8125.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Emulate the 802.3bz MMD EEE registers for 2.5Gbps EEE on RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add EEE-related constants. This includes the new MMD EEE registers for
NBase-T / 802.3bz.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RCU list block_ing_cb_list is protected by rcu read lock in
flow_block_ing_cmd() and with flow_indr_block_ing_cb_lock mutex in all
functions that use it. However, flow_block_ing_cmd() needs to call blocking
functions while iterating block_ing_cb_list which leads to following
suspicious RCU usage warning:

[  401.510948] =============================
[  401.510952] WARNING: suspicious RCU usage
[  401.510993] 5.3.0-rc3+ #589 Not tainted
[  401.510996] -----------------------------
[  401.511001] include/linux/rcupdate.h:265 Illegal context switch in RCU read-side critical section!
[  401.511004]
               other info that might help us debug this:

[  401.511008]
               rcu_scheduler_active = 2, debug_locks = 1
[  401.511012] 7 locks held by test-ecmp-add-v/7576:
[  401.511015]  #0: 00000000081d71a5 (sb_writers#4){.+.+}, at: vfs_write+0x166/0x1d0
[  401.511037]  #1: 000000002bd338c3 (&of->mutex){+.+.}, at: kernfs_fop_write+0xef/0x1b0
[  401.511051]  #2: 00000000c921c634 (kn->count#317){.+.+}, at: kernfs_fop_write+0xf7/0x1b0
[  401.511062]  #3: 00000000a19cdd56 (&dev->mutex){....}, at: sriov_numvfs_store+0x6b/0x130
[  401.511079]  #4: 000000005425fa52 (pernet_ops_rwsem){++++}, at: unregister_netdevice_notifier+0x30/0x140
[  401.511092]  #5: 00000000c5822793 (rtnl_mutex){+.+.}, at: unregister_netdevice_notifier+0x35/0x140
[  401.511101]  #6: 00000000c2f3507e (rcu_read_lock){....}, at: flow_block_ing_cmd+0x5/0x130
[  401.511115]
               stack backtrace:
[  401.511121] CPU: 21 PID: 7576 Comm: test-ecmp-add-v Not tainted 5.3.0-rc3+ #589
[  401.511124] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[  401.511127] Call Trace:
[  401.511138]  dump_stack+0x85/0xc0
[  401.511146]  ___might_sleep+0x100/0x180
[  401.511154]  __mutex_lock+0x5b/0x960
[  401.511162]  ? find_held_lock+0x2b/0x80
[  401.511173]  ? __tcf_get_next_chain+0x1d/0xb0
[  401.511179]  ? mark_held_locks+0x49/0x70
[  401.511194]  ? __tcf_get_next_chain+0x1d/0xb0
[  401.511198]  __tcf_get_next_chain+0x1d/0xb0
[  401.511251]  ? uplink_rep_async_event+0x70/0x70 [mlx5_core]
[  401.511261]  tcf_block_playback_offloads+0x39/0x160
[  401.511276]  tcf_block_setup+0x1b0/0x240
[  401.511312]  ? mlx5e_rep_indr_setup_tc_cb+0xca/0x290 [mlx5_core]
[  401.511347]  ? mlx5e_rep_indr_tc_block_unbind+0x50/0x50 [mlx5_core]
[  401.511359]  tc_indr_block_get_and_ing_cmd+0x11b/0x1e0
[  401.511404]  ? mlx5e_rep_indr_tc_block_unbind+0x50/0x50 [mlx5_core]
[  401.511414]  flow_block_ing_cmd+0x7e/0x130
[  401.511453]  ? mlx5e_rep_indr_tc_block_unbind+0x50/0x50 [mlx5_core]
[  401.511462]  __flow_indr_block_cb_unregister+0x7f/0xf0
[  401.511502]  mlx5e_nic_rep_netdevice_event+0x75/0xb0 [mlx5_core]
[  401.511513]  unregister_netdevice_notifier+0xe9/0x140
[  401.511554]  mlx5e_cleanup_rep_tx+0x6f/0xe0 [mlx5_core]
[  401.511597]  mlx5e_detach_netdev+0x4b/0x60 [mlx5_core]
[  401.511637]  mlx5e_vport_rep_unload+0x71/0xc0 [mlx5_core]
[  401.511679]  esw_offloads_disable+0x5b/0x90 [mlx5_core]
[  401.511724]  mlx5_eswitch_disable.cold+0xdf/0x176 [mlx5_core]
[  401.511759]  mlx5_device_disable_sriov+0xab/0xb0 [mlx5_core]
[  401.511794]  mlx5_core_sriov_configure+0xaf/0xd0 [mlx5_core]
[  401.511805]  sriov_numvfs_store+0xf8/0x130
[  401.511817]  kernfs_fop_write+0x122/0x1b0
[  401.511826]  vfs_write+0xdb/0x1d0
[  401.511835]  ksys_write+0x65/0xe0
[  401.511847]  do_syscall_64+0x5c/0xb0
[  401.511857]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  401.511862] RIP: 0033:0x7fad892d30f8
[  401.511868] Code: 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 96 0d 00 8b 00 85 c0 75 17 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 60 c3 0f 1f 80 00 00 00 00 48 83
 ec 28 48 89
[  401.511871] RSP: 002b:00007ffca2a9fad8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[  401.511875] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fad892d30f8
[  401.511878] RDX: 0000000000000002 RSI: 000055afeb072a90 RDI: 0000000000000001
[  401.511881] RBP: 000055afeb072a90 R08: 00000000ffffffff R09: 000000000000000a
[  401.511884] R10: 000055afeb058710 R11: 0000000000000246 R12: 0000000000000002
[  401.511887] R13: 00007fad893a8780 R14: 0000000000000002 R15: 00007fad893a3740

To fix the described incorrect RCU usage, convert block_ing_cb_list from
RCU list to regular list and protect it with flow_indr_block_ing_cb_lock
mutex in flow_block_ing_cmd().

Fixes: 1150ab0f ("flow_offload: support get multi-subsystem block")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge conflict of mlx5 resolved using instructions in merge
commit 9566e650.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

  1) Fix jmp to 1st instruction in x64 JIT, from Alexei Starovoitov.

  2) Severl kTLS fixes in mlx5 driver, from Tariq Toukan.

  3) Fix severe performance regression due to lack of SKB coalescing of
     fragments during local delivery, from Guillaume Nault.

  4) Error path memory leak in sch_taprio, from Ivan Khoronzhuk.

  5) Fix batched events in skbedit packet action, from Roman Mashak.

  6) Propagate VLAN TX offload to hw_enc_features in bond and team
     drivers, from Yue Haibing.

  7) RXRPC local endpoint refcounting fix and read after free in
     rxrpc_queue_local(), from David Howells.

  8) Fix endian bug in ibmveth multicast list handling, from Thomas
     Falcon.

  9) Oops, make nlmsg_parse() wrap around the correct function,
     __nlmsg_parse not __nla_parse(). Fix from David Ahern.

 10) Memleak in sctp_scend_reset_streams(), fro Zheng Bin.

 11) Fix memory leak in cxgb4, from Wenwen Wang.

 12) Yet another race in AF_PACKET, from Eric Dumazet.

 13) Fix false detection of retransmit failures in tipc, from Tuong
     Lien.

 14) Use after free in ravb_tstamp_skb, from Tho Vu.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
  ravb: Fix use-after-free ravb_tstamp_skb
  netfilter: nf_tables: map basechain priority to hardware priority
  net: sched: use major priority number as hardware priority
  wimax/i2400m: fix a memory leak bug
  net: cavium: fix driver name
  ibmvnic: Unmap DMA address of TX descriptor buffers after use
  bnxt_en: Fix to include flow direction in L2 key
  bnxt_en: Use correct src_fid to determine direction of the flow
  bnxt_en: Suppress HWRM errors for HWRM_NVM_GET_VARIABLE command
  bnxt_en: Fix handling FRAG_ERR when NVM_INSTALL_UPDATE cmd fails
  bnxt_en: Improve RX doorbell sequence.
  bnxt_en: Fix VNIC clearing logic for 57500 chips.
  net: kalmia: fix memory leaks
  cx82310_eth: fix a memory leak bug
  bnx2x: Fix VF's VLAN reconfiguration in reload.
  Bluetooth: Add debug setting for changing minimum encryption key size
  tipc: fix false detection of retransmit failures
  lan78xx: Fix memory leaks
  MAINTAINERS: r8169: Update path to the driver
  MAINTAINERS: PHY LIBRARY: Update files in the record
  ...

The maximum key description size is 4095.  Commit f771fde8 ("keys:
Simplify key description management") inadvertantly reduced that to 255
and made sizes between 256 and 4095 work weirdly, and any size whereby
size & 255 == 0 would cause an assertion in __key_link_begin() at the
following line:

	BUG_ON(index_key->desc_len == 0);

This can be fixed by simply increasing the size of desc_len in struct
keyring_index_key to a u16.

Note the argument length test in keyutils only checked empty
descriptions and descriptions with a size around the limit (ie.  4095)
and not for all the values in between, so it missed this.  This has been
addressed and

	https://git.kernel.org/pub/scm/linux/kernel/git/dhowells/keyutils.git/commit/?id=066bf56807c26cd3045a25f355b34c1d8a20a5aa

now exhaustively tests all possible lengths of type, description and
payload and then some.

The assertion failure looks something like:

 kernel BUG at security/keys/keyring.c:1245!
 ...
 RIP: 0010:__key_link_begin+0x88/0xa0
 ...
 Call Trace:
  key_create_or_update+0x211/0x4b0
  __x64_sys_add_key+0x101/0x200
  do_syscall_64+0x5b/0x1e0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

It can be triggered by:

	keyctl add user "aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa" a @s

Fixes: f771fde8 ("keys: Simplify key description management")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch adds the call to phy_attached_info() to the hns driver
to identify which exact PHY drivers is in use.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a Tx timestamp is requested, a pointer to the skb is stored in the
ravb_tstamp_skb struct. This was done without an skb_get. There exists
the possibility that the skb could be freed by ravb_tx_free (when
ravb_tx_free is called from ravb_start_xmit) before the timestamp was
processed, leading to a use-after-free bug.

Use skb_get when filling a ravb_tstamp_skb struct, and add appropriate
frees/consumes when a ravb_tstamp_skb struct is freed.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Tho Vu <tho.vu.wh@rvc.renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the MediaTek MT7628/88 SoCs to the common
MediaTek ethernet driver. Some minor changes are needed for this and
a bigger change, as the MT7628 does not support QDMA (only PDMA).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: René van Dorst <opensource@vdorst.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>