As per the DT phy-mode specification, RGMII delays are applied by the
MAC when there is no PHY present on the link.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pad_mii_tx registers point to the same memory region but were
unused. So convert to using these for RGMII I/O cell configuration, as
they bear a shorter name.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This puts the quad PHY ports in power-down mode when the PHY transitions
to the PHY_HALTED state.  It is likely that all the other PHYs support
the BMCR_PDOWN bit, but I only have the BCM5464R to test.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Rethink PHYLINK callbacks for SJA1105 DSA

This patchset implements phylink_mac_link_up and phylink_mac_link_down,
while also removing the code that was modifying the EGRESS and INGRESS
MAC settings for STP and replacing them with the "inhibit TX"
functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The first fact that needs to be stated is that the per-MAC settings in
SJA1105 called EGRESS and INGRESS do *not* disable egress and ingress on
the MAC. They only prevent non-link-local traffic from being
sent/received on this port.

So instead of having .phylink_mac_config essentially mess with the STP
state and force it to DISABLED/BLOCKING (which also brings useless
complications in sja1105_static_config_reload), simply add the
.phylink_mac_link_down and .phylink_mac_link_up callbacks which inhibit
TX at the MAC level, while leaving RX essentially enabled.

Also stop from trying to put the link down in .phylink_mac_config, which
is incorrect.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will be used to stop egress traffic in .phylink_mac_link_up.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the driver is now using PHYLINK exclusively, it makes sense to
remove all references to it and replace them with PHYLINK.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic patch that replaces the link speed numbers used in
the driver with the corresponding ethtool macros.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix below warnings reported by coccicheck

net/key/af_key.c:932:2-5: WARNING: Use BUG_ON instead of if condition
followed by BUG.
net/key/af_key.c:948:2-5: WARNING: Use BUG_ON instead of if condition
followed by BUG.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot found a crash in tcp_v6_send_reset() caused by my latest
change.

Problem is that if an skb has been queued to socket prequeue,
skb_dst(skb)->dev can not anymore point to the device.

Fortunately in this case the socket pointer is not NULL.

A similar issue has been fixed in commit 0f85feae ("tcp: fix
more NULL deref after prequeue changes"), I should have known better.

Fixes: 323a53c4 ("ipv6: tcp: enable flowlabel reflection in some RST packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sebastian Andrzej says:

====================
Avoid local_irq_save() and use napi_alloc_frag() where possible

The first two patches remove local_irq_save() around
`netdev_alloc_cache' which does not work on -RT. Besides helping -RT it
whould benefit the users of the function since they can avoid disabling
interrupts and save a few cycles.
The remaining patches are from a time when I tried to remove
`netdev_alloc_cache' but then noticed that we still have non-NAPI
drivers using netdev_alloc_skb() and I dropped that idea. Using
napi_alloc_frag() over netdev_alloc_frag() would skip the not required
local_bh_disable() around the allocation.

v1…v2:
  - 1/7 + 2/7 use now "(in_irq() || irqs_disabled())" instead just
    "irqs_disabled()" to align with __dev_kfree_skb_any(). Pointed out
    by Eric Dumazet.

  - 6/7 has a typo less. Pointed out by Sergei Shtylyov.

  - 3/7 + 4/7 added acks from Ioana Radulescu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on review, `lock' is only acquired in hwbm_pool_add() which is
invoked via ->probe(), ->resume() and ->ndo_change_mtu(). Based on this
the lock can become a mutex and there is no need to disable interrupts
during the procedure.
Now that the lock is a mutex, hwbm_pool_add() no longer invokes
hwbm_pool_refill() in an atomic context so we can pass GFP_KERNEL to
hwbm_pool_refill() and remove the `gfp' argument from hwbm_pool_add().

Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3_alloc_rx_data() uses netdev_alloc_frag() for skb allocation. All
callers of tg3_alloc_rx_data() either hold tp->lock (which is held with
BH disabled) or run in NAPI context.

Use napi_alloc_frag() for skb allocations.

Cc: Siva Reddy Kallam <siva.kallam@broadcom.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

SKB allocation via bnx2x_frag_alloc() is always performed in NAPI
context. Preemptible context passes GFP_KERNEL and bnx2x_frag_alloc()
uses then __get_free_page() for the allocation.

Use napi_alloc_frag() for memory allocation.

Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver is using netdev_alloc_frag() for allocation in the
->ndo_start_xmit() path. That one is always invoked in a BH disabled
region so we could also use napi_alloc_frag().

Use napi_alloc_frag() for skb allocation.

Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the comment, the preempt_disable() statement is required
due to synchronisation in napi_alloc_frag(). The awful truth is that
local_bh_disable() is required because otherwise the NAPI poll callback
can be invoked while the open function setup buffers. This isn't
unlikely since the dpaa2 provides multiple devices.

The usage of napi_alloc_frag() has been removed in commit

 27c87486 ("dpaa2-eth: Use a single page per Rx buffer")

which means that the comment is not accurate and the preempt_disable()
statement is not required.

Remove the outdated comment and the no longer required
preempt_disable().

Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

__netdev_alloc_skb() can be used from any context and is used by NAPI
and non-NAPI drivers. Non-NAPI drivers use it in interrupt context and
NAPI drivers use it during initial allocation (->ndo_open() or
->ndo_change_mtu()). Some NAPI drivers share the same function for the
initial allocation and the allocation in their NAPI callback.

The interrupts are disabled in order to ensure locked access from every
context to `netdev_alloc_cache'.

Let __netdev_alloc_skb() check if interrupts are disabled. If they are, use
`netdev_alloc_cache'. Otherwise disable BH and use `napi_alloc_cache.page'.
The IRQ check is cheaper compared to disabling & enabling interrupts and
memory allocation with disabled interrupts does not work on -RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev_alloc_frag() can be used from any context and is used by NAPI
and non-NAPI drivers. Non-NAPI drivers use it in interrupt context
and NAPI drivers use it during initial allocation (->ndo_open() or
->ndo_change_mtu()). Some NAPI drivers share the same function for the
initial allocation and the allocation in their NAPI callback.

The interrupts are disabled in order to ensure locked access from every
context to `netdev_alloc_cache'.

Let netdev_alloc_frag() check if interrupts are disabled. If they are,
use `netdev_alloc_cache' otherwise disable BH and invoke
__napi_alloc_frag() for the allocation. The IRQ check is cheaper
compared to disabling & enabling interrupts and memory allocation with
disabled interrupts does not work on -RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robert Hancock says:

====================
SFP polling fixes

This has an updated version of an earlier patch to ensure that SFP
operations are stopped during shutdown, and another patch suggested by
Russell King to address a potential concurrency issue with SFP state
checks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFP device polling can cause problems during the shutdown process if the
parent devices of the network controller have been shut down already.
This problem was seen on the iMX6 platform with PCIe devices, where
accessing the device after the bus is shut down causes a hang.

Free any acquired GPIO interrupts and stop all delayed work in the SFP
driver during the shutdown process, so that we ensure that no pending
operations are still occurring after the SFP shutdown completes.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

The nhg->nh_entries[] array is allocated in nexthop_grp_alloc() and it
has nhg->num_nh elements so this check should be >= instead of >.

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jarod Wilson says:

====================
bonding: clean up and standarize logging printks

This set improves a few somewhat terse bonding debug messages, fixes some
errors in others, and then standarizes the majority of them, using new
slave_* printk macros that wrap around netdev_* to ensure both master
and slave information is provided consistently, where relevant. This set
proves very useful in debugging issues on hosts with multiple bonds.

I've run an array of LNST tests over this set, creating and destroying
quite a few different bonds of the course of testing, fixed the little
gotchas here and there, and everything looks stable and reasonable to me,
but I can't guarantee I've tested every possible message and scenario to
catch every possible "slave could be NULL" case.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Where possible, we generally want both the bond master and the relevant slave
information in message output. Standardize the format using new slave_*
printk macros.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing the bond name again to debug output when referencing slave is wrong.
We're trying to set the bond's MAC to that of the new_active slave, so adjust
the error message slightly and pass in the slave's name, not the bond's.
Then we're trying to set the MAC on the old active slave, but putting the
new active slave's name in the output. While we're at it, clarify the
error messages so you know which one actually triggered.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Seeing bonding debug log data along the lines of "event: 5" is a bit spartan,
and often requires a lookup table if you don't remember what every event is.
Make use of netdev_cmd_to_name for an improved debugging experience, so for
the prior example, you'll see: "bond_netdev_event received NETDEV_REGISTER"
instead (both are prefixed with the device for which the event pertains).

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_err() is more appropriate for printing error messages inside
drivers, so switch to dev_err().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spread initial IRQ affinity hints across the device node CPUs,
for nic queue and uld queue IRQs, to load balance and avoid
all interrupts on CPU0.
Signed-off-by: Nirranjan Kirubaharan <nirranjan@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: some code optimizations & cleanups & bugfixes

This patch-set includes code optimizations, cleanups and bugfixes for
the HNS3 ethernet controller driver.

[patch 1/12] logs more detail error info for ROCE RAS errors.

[patch 2/12] fixes a wrong size issue for mailbox responding.

[patch 3/12] makes HW GRO handing compliant with SW one.

[patch 4/12] refactors hns3_get_new_int_gl.

[patch 5/12] adds handling for VF's over_8bd_nfe_err.

[patch 6/12 - 12/12] adds some code optimizations and cleanups, to
make the code more readable and compliant with some static code
analysis tools, these modifications do not change the logic of
the code.

Change log:
V1->V2: fixes comment from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some coding style issues reported by some static code
analysis tools and code review, such as modify some comments, rename
some variables, log some errors in detail, and fixes some alignment
errors.

BTW, these cleanups do not change the logic of code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: HuiSong Li <lihuisong@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes some redundant code and refactors some bloated
functions.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to make it more readable, this patch modifies PF/VF's
RSS hash key configuring function.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds some macros instead of magic numbers in serval places
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to improve readability, this patch uses macros to
replace some magic numbers, and adds some comments for some
others.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since HNAE3_CLIENT_UNIC and HNAE3_DEV_UNIC is not used any more,
this patch removes the redundant codes.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We trigger PF reset when a RAS error of NIC named over_8bd_nfe_err
occurred before. But it is possible that a VF causes that error, it's
reasonable to trigger VF reset instead of PF reset in this case.
This patch add detection of vf_id if a over_8bd_nfe_err occurs, if
vf_id is 0, we trigger PF reset. Otherwise, we will trigger VF reset
on the VF with error.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>