[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.

[How]
- Pull get_active_display_cnt out to clk_mgr.
- Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
DMUB is using DPREF CLK, but DMCU still use displayclk.
This is for updating DMCU wait_for_loop after display clock change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.

Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.

Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.

We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.

[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
link-specific functions should reside in dc_link.c

[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Current calculation of bounding box will cause DML to increase voltage
state due to DPP or DISPCLK, this is unnecessary since from DML perspective
we can max DPP/DISP can be supported at DPM0.  This is because
increasing voltage for DPP/DISP is done separately via actual minimum values
of DISP and DPP CLK

[how]
For each calculated state, DPP, DISP, PHY, and DSC clk should always be set to
maximum.  FCLK, SOCCLK, and DCFCLK should be based of UCLK.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
1. DMCU is not running on some platform but driver still send ABM
   command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable

[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
   determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.

[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

caller of pp_nv_set_pme_wa_enable pass incorrect pp_smu:
dc->res_pool->pp_smu. it should be dc->res_pool->pp_smu->nv_funcs.pp_smu.
with incorrect input, pp->dm = NULL. This causes system crash.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
VTG has a parameter FP2, which is defined as:
    if VSTARTUP is before VSYNC:
        FP2 = number of lines in between VSTARTUP and VSYNC
    else
        FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.

[How]
 - refactor VTG_CONTROL programming into a new function "set_vtg_params"
 - call it after calling "program_global_sync"
   - make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support for DCN2 DSC (Display Stream Compression)

HW Blocks:

 +--------++------+       +----------+
 | HUBBUB || HUBP |  <--  | MMHUBBUB |
 +--------++------+       +----------+
        |                     ^
        v                     |
    +--------+            +--------+
    |  DPP   |            |  DWB   |
    +--------+            +--------+
        |
        v                      ^
    +--------+                 |
    |  MPC   |                 |
    +--------+                 |
        |                      |
        v                      |
    +-------+      +-------+   |
    |  OPP  | <--> |  DSC  |   |
    +-------+      +-------+   |
        |                      |
        v                      |
    +--------+                /
    |  OPTC  |  --------------
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+

v2: rebase (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable the IP for navi10.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable DCN2 support in DM (Display Manager).

v2: fix spurious raven change (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

To deal with rebasing the code.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pass extra parameter to validate_bandwidth() callback.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

To deal with changes from rebasing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

during bring up time, before window dc-ppplib interface
design, linux dc use raven dc-pplib interface.
now nvai10 dc-pplib-smu interface is changed and verified
under window, navi10 need its specific dc-pplib-smu
interface. todo: hook set_hard_min_uclk_by_freq,
get_maximum_sustainable_clocks
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

dc needs get uclk dpm table for bandwidth calculation
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

dc (display component) needs maximum clock values of uclock,
socclk, dcefclk, to calculate display bandwidth.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Core DC changes for DCN2.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add DCN2 resource definition and HW Sequencer changes.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program DCN2 VMID (Virtual Memory Support)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program DCN2 cursor (IPP)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program the DCN2 DWB (Display Writeback)

HW Blocks:

 +--------++------+       +----------+
 | HUBBUB || HUBP |  <--  | MMHUBBUB |
 +--------++------+       +----------+
        |                     ^
        v                     |
    +--------+            +--------+
    |  DPP   |            |  DWB   |
    +--------+            +--------+
        |
        v                      ^
    +--------+                 |
    |  MPC   |                 |
    +--------+                 |
        |                      |
        v                      |
    +-------+                  |
    |  OPP  |                  |
    +-------+                  |
        |                      |
        v                      |
    +--------+                /
    |  OPTC  |  --------------
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program the DCN2 MMHUBBUB (Multimedia HUB interface)

HW Blocks:

 +--------++------+       +----------+
 | HUBBUB || HUBP |  <--  | MMHUBBUB |
 +--------++------+       +----------+
        |
        v
    +--------+
    |  DPP   |
    +--------+
        |
        v
    +--------+
    |  MPC   |
    +--------+
        |
        v
    +-------+
    |  OPP  |
    +-------+
        |
        v
    +--------+
    |  OPTC  |
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program the DCN2 HUBP (Display to data fabric interface
pipe) and HUBBUB (DCN memory HUB interface)

HW Blocks:

 +--------++------+
 | HUBBUB || HUBP |
 +--------++------+
        |
        v
    +--------+
    |  DPP   |
    +--------+
        |
        v
    +--------+
    |  MPC   |
    +--------+
        |
        v
    +-------+
    |  OPP  |
    +-------+
        |
        v
    +--------+
    |  OPTC  |
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program the DCN2 DPP (Multiple pipe and plane combine)

HW Blocks:

    +--------+
    |  DPP   |
    +--------+
        |
        v
    +--------+
    |  MPC   |
    +--------+
        |
        v
    +-------+
    |  OPP  |
    +-------+
        |
        v
    +--------+
    |  OPTC  |
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program the DCN2 MPC (Multiple pipe and plane combine)

HW Blocks:

    +--------+
    |  MPC   |
    +--------+
        |
        v
    +-------+
    |  OPP  |
    +-------+
        |
        v
    +--------+
    |  OPTC  |
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program the DCN2 OPP (Output Plane Processing)

HW Blocks:

    +-------+
    |  OPP  |
    +-------+
        |
        v
    +--------+
    |  OPTC  |
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support for programming the DCN2 OPTC (Output Timing Controller)

HW Blocks:

    +--------+
    |  OPTC  |
    +--------+
        |
        v
    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adds support for handling of clocking relevant to the DCN2 block,
including programming of the DCCG (Display Controller Clock Generator)
block:

HW Blocks:

    +--------+       +--------+
    |  DIO   |       |  DCCG  |
    +--------+       +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support for the DIO (Display IO)  block of DCN2, which entails our
stream and link encoders.

HW Blocks:

    +--------+
    |  DIO   |
    +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update DML (Display Mode Lib) to support DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support to program DCN2 IRQ handling
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Handle BIOS parsing for DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adding support to program GPIO HW block of DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adding support to program DCN2 AUX and I2C HW.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

DCN2.0 (Display Core Next) is the display block in Navi10.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

since it's firmware.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

DC needs to include the soc bounding box when initializing HW resources.

Including amdgpu_ucode.h directly will cause warnings, since amdgpu.h is
required to define amdgpu_device. The solution here is to split the
bounding box structs into a different header, then include it in both
amdgpu_ucode.h, and relevant DC HW resource files.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
We don't want to expose sensitive ASIC information before ASIC release.

[HOW]
Encode the soc_bounding_box in the gpu_info FW (for Linux) and read it
at driver load.

v2: fix warning when CONFIG_DRM_AMD_DC_DCN2_0 is not set (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>