The old "cooling-{min,max}-state" properties for thermal bindings were
ratified to "cooling-{min,max}-level" by commit eb168b70 ("of:
thermal: Fix inconsitency between cooling-*-state and cooling-*-level"),
which were later removed entirely by commit e04907db ("dt-bindings:
thermal: Remove "cooling-{min|max}-level" properties").

The pwm-fan binding, however, was apparently in-flight in parallel with
that ratification, and so managed to introduce an example of the old
properties which escaped the scope of the later cleanup and has thus
continued to be dutifully copied for new boards despite being useless.
Clean up these remaining undocumented anachronisms to minimise any
further confusion.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu dt64 for 5.2 (part 1)

Add wlan_disable signal hog for rfkill signal on clearfog-gt-8k
(Armada 8040 based board)

* tag 'mvebu-dt64-5.2-1' of git://git.infradead.org/linux-mvebu:
  arm64: dts: clearfog-gt-8k: add wlan_disable signal hog
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu dt for 5.2 (part 1)

 - Add interrupt support for wathdog on Armada 38x

* tag 'mvebu-dt-5.2-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: armada-38x: add interrupts for watchdog
Signed-off-by: Olof Johansson <olof@lixom.net>

* 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: at91-vinco: use SPDX-License-Identifier
  ARM: dts: atmel boards: use SPDX-License-Identifier
  ARM: dts: at91sam9xe: use SPDX-License-Identifier
  ARM: dts: sama5d{2,4}: use SPDX-License-Identifier
  ARM: dts: at91: sama5d2_xplained: Add proper regulator states for suspend-to-mem
  ARM: dts: at91: sama5d2: add labels to soc dtsi for derivative boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-dts-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/dt

Qualcomm Device Tree Changes for v5.2

* Add gpio ranges for Qualcomm platforms
* Correct the IPQ4019 PCIe BAR range

* tag 'qcom-dts-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: qcom: ipq4019: enlarge PCIe BAR range
  ARM: dts: qcom: pma8084: add gpio-ranges
  ARM: dts: qcom: msm8660: add gpio-ranges
  ARM: dts: qcom: mdm9615: add gpio-ranges
  ARM: dts: qcom: apq8064: add gpio-ranges
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-arm64-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/dt

Qualcomm ARM64 Updates for v5.2

* Add gpio ranges for Qualcomm platforms
* Fix MSM8998 BLSP2 I2C5 address
* Add MSM8998 UFS nodes and associated information
* Add SDM845 interconnect header and usage
* Add ADSP and CDSP PAS, RMTFS memory, and UFS phy reset on SDM845
* Update reserved memory map on SDM845
* Add QCS404 spmi regulators, ethernet, bluetooth, and uart3
* Remove remotely-controlled property as default for BAM on QCS404
* Add spmi regulators on PMS405
* Fixup QCS404 l3 voltages and regulator supply names
* Fixup thermal trip names on Qualcomm platforms
* Add thermal sensors on Qualcomm platforms
* Remove invalid efficiency property on MSM8998
* Change QCS404-evb compatible to help distinguish platforms
* Add rpmhd header file and convert to use definitions on SDM845
* Add interconnect header file on SDM845
* Add PMS405 ADC binding

* tag 'qcom-arm64-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (38 commits)
  arm64: dts: sdm845: Introduce ADSP and CDSP PAS nodes
  arm64: dts: qcom: sdm845: Define rmtfs memory
  arm64: dts: qcom: sdm845: Update reserved memory map
  arm64: dts: sdm845: Add UFS PHY reset
  arm64: dts: qcom: msm8998: Fix blsp2_i2c5 address
  arm64: dts: qcom: qcs404-evb: Change the compatible to distinguish platforms
  arm64: dts: qcom: pmi8998: add gpio-ranges
  arm64: dts: qcom: pmi8994: add gpio-ranges
  arm64: dts: qcom: pm8998: add gpio-ranges
  arm64: dts: qcom: pm8005: add gpio-ranges
  arm64: dts: msm8998: Add UFS phy reset
  arm64: dts: msm8916: thermal: Convert camera trip type to hot
  arm64: dts: msm8996: thermal: Make trip names consistent
  arm64: dts: msm8916: thermal: Make trip names consistent
  arm64: dts: msm8998: thermal: Make trip names consistent
  arm64: dts: sdm845: thermal: Add temperature sensors near major peripherals
  arm64: dts: msm8998: thermal: Add temperature sensors near major peripherals
  arm64: dts: msm8998: thermal: GPU has two sensors, add the second
  arm64: dts: msm8998: thermal: Fix the gpu sensor number
  arm64: dts: msm8998: thermal: Fix the cpu sensor numbers
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

i.MX arm device tree update for 5.2:
 - New board support: imx50-kobo-aura, imx53-m53menlo, imx6dl-eckelmann,
   imx7d-mba7, imx7d-zii-rpu2, and vf610-zii-spb4.
 - Add i2c, mmc and spi aliases for SoC i.MX35, i.MX50 and i.MX6SL.
 - Use new 'reset-gpios' property describing CODEC reset pin for board
   mx6qdl-zii-rdu2, imx6qdl-gw5903 and imx6qdl-var-dart.
 - Specify viewport count for PCIE block on SoC imx7d and imx6qdl.
 - Correct 'ipg' clock of SDMA device for i.MX5, i.MX6 and i.MX7 SoCs.
 - Rename MMDC memory controller device to be generic and add MMDC
   device for imx7ulp SoC.
 - Add OCOTP device support for imx7ulp SoC.
 - Improve ZII board DTS by switching to SPDX identifier and using generic
   device node name.
 - A series from Rui Miguel Silva to add various media related devices
   for i.MX7 SoC, and enable ov2680 sensor support for imx7s-warp board.
 - Random small updates on various board support.

* tag 'imx-dt-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (59 commits)
  ARM: dts: imx7s: Specify #io-channel-cells in ADC nodes
  ARM: dts: vf610-zii-dev-rev-b: Specify CS as GPIO_ACTIVE_LOW in spi0
  ARM: dts: vf610-zii-dev: Mark i2c0 SCL as GPIO_OPEN_DRAIN
  ARM: dts: Add support for ZII i.MX7 RPU2 board
  ARM: dts: bugfix tqma7 soft reset issue
  ARM: dts: imx53: Add Menlosystems M53 board
  ARM: dts: imx53: Rename M53 SoM touchscreen node
  ARM: dts: imx6dl-sabreauto: update opp table for auto part
  ARM: dts: imx: Use generic node names for Zii dts
  ARM: dts: imx: Switch Zii dts to SPDX identifier
  ARM: dts: imx6q-logicpd: Shutdown LCD regulator during suspend
  ARM: dts: imx6q-logicpd: Enable Analog audio capture
  ARM: dts: imx6sll: add cooling-cells for cpu-freq cooling device
  ARM: dts: imx50: Add Kobo Aura DTS
  ARM: dts: imx6qdl-var-dart: Use new CODEC reset pin name
  ARM: dts: imx6qdl-gw5903: Use new CODEC reset pin name
  ARM: dts: mx6qdl-zii-rdu2: Use new CODEC reset pin name
  ARM: dts: imx50: Specify IMX5_CLK_IPG as "ahb" clock to SDMA
  ARM: dts: imx51: Specify IMX5_CLK_IPG as "ahb" clock to SDMA
  ARM: dts: imx53: Specify IMX5_CLK_IPG as "ahb" clock to SDMA
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-bindings-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX DT bindings update for 5.2:
 - Add vendor prefix for TQ Systems GmbH, Rakuten Kobo and Menlo Systems
   GmbH.
 - Add DT schema for SoC i.MX8MM and i.MX50, and board ZII VF610, VF610
   SPB4, i.MX7 RPU2, i.MX7S TQ MBa7, M53 Menlo and Eckelmann ci4x10.
 - Update imx-scu bindings on resource table and general interrupt
   support.
 - Add bindings for i.MX MMDC memory controller.
 - Update i.MX7D ADC bindings to add missing '#io-channel-cells'
   property.

* tag 'imx-bindings-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  dt-bindings: iio: imx7d-adc: Add #io-channel-cells to required
  dt-bindings: arm: fsl: Add support for ZII i.MX7 RPU2 board
  dt-bindings: arm: fsl: Add devicetree binding for M53 Menlo board.
  dt-bindings: fsl: scu: add general interrupt support
  dt-bindings: arm: fsl: Add i.MX50 based boards
  dt-bindings: Add vendor prefix for Rakuten Kobo, Inc.
  dt-bindings: arm: add TQ boards
  dt-bindings: add vendor prefix for TQ Systems GmbH
  dt-bindings: arm: fsl: Add support for ZII VF610 SPB4
  dt-bindings: arm: fsl: Add supported ZII VF610 boards to DT schema
  dt-bindings: arm: imx: Add the soc binding for imx8mm
  dt-bindings: arm: fsl: Add devicetree binding for Eckelmann ci4x10
  dt-bindings: memory-controllers: freescale: add MMDC binding doc
  of: Add vendor prefix for Menlo Systems GmbH
  bindings: fsl-imx-sdma: Document fsl,imx8mq-sdma compatbile string
  dt-bindings: firmware: imx-scu: add new resources to scu resource table
  dt-bindings: firmware: imx-scu: remove unused resources from scu resource table
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt

arm64: dts: Amlogic updates for v5.2, round 2
- add display/gfx support for G12a boards
- enable USB for g12a boards

* tag 'amlogic-dt64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (26 commits)
  arm64: dts: meson-g12a-u200: Add support for Video Display
  arm64: dts: meson-g12a-sei510: Add support for Video Display
  arm64: dts: meson-g12a-x96-max: Add support for Video Display
  arm64: dts: meson-g12a: Add AO-CEC nodes
  arm64: dts: meson-g12a: Add VPU and HDMI related nodes
  arm64: dts: meson-g12a-x96-max: Enable USB
  arm64: dts: meson-g12a-u200: Enable USB
  arm64: dts: meson-g12a-sei510: Enable USB
  arm64: dts: meson-g12a-sei510: Add ADC Key and BT support
  arm64: dts: meson-g12a-u200: add regulators
  arm64: dts: meson: g12a: Add mali-g31 gpu node
  arm64: dts: meson: g12a: Add G12A USB nodes
  arm64: dts: meson: g12a: Add SAR ADC node
  dt-bindings: power: amlogic, meson-gx-pwrc: Add G12A compatible
  arm64: dts: meson-gxm: Add Mali-T820 node
  dt-bindings: gpu: mali-midgard: Add resets property
  dt-bindings: clock: meson8b: export the video decoder clocks
  dt-bindings: clock: meson8b: export the VPU clock
  dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
  dt-bindings: clock: meson8b: drop the "ABP" clock definition
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt

ARM: dts: Amlogic updates for v5.2, round 2
- enable RTC on odroid-c1, ec100
- meson8: add internal clock measurer

* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8b: odroid-c1: prepare support for the RTC
  ARM: dts: meson8b: ec100: enable the RTC
  ARM: dts: meson: add support for the RTC
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt-bindings-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt

Renesas ARM Based SoC DT Bindings Updates for v5.2

* R-Car M3-N (r8a77965) SoC
  - Remove non-existent A3IR power domain

* Add vendor prefix for Silicon Linux

* tag 'renesas-dt-bindings-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  dt-bindings: power: r8a77965: Remove non-existent A3IR power domain
  dt-bindings: Add vendor prefix for Silicon Linux.
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm-dt-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt

Renesas ARM Based SoC DT Updates for v5.2

* R-Car E2 (r8a7794) based Alt board
  - Enable USB and DA9063 PMIC

* R-Car V2H (R8A77920) based Blanche board
  - Enable IIC3 and DA9063 PMIC

* RZ/G1C (r8a77470) based iWave SBC
  - Enable HDMI, USB Phy[01], USB2.0 Host and HS-USB

* RZ/G1C (r8a77470) SoC
  - Describe DU, VIN, PWM and HSCIF, USB PHY, USB2.0 Host and HSUSB in DT

* RZ/A1H (R7S7210) based rskrza1 board
  - Enable remaining LEDs and I2C

* R-Mobile A1 (r8a7740) based ape6evm,
  R-Car H1 (r8a7779) based marzen,
  R-Car M1A (R8A7778) based bockw and
  Emma Mobile EV2 based kzm9d boads
  - Tidy up bootargs

* R-Mobile A1 (r8a7740) based ape6evm
  - Enable NOR FLASH

* tag 'renesas-arm-dt-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (21 commits)
  ARM: dts: ape6evm: Reorder bootargs
  ARM: dts: marzen: Add rw to bootargs and use ip=dhcp
  ARM: dts: bockw: Reorder bootargs
  ARM: dts: kzm9d: Add rw parameter to bootargs
  ARM: dts: iwg23s-sbc: Enable HS-USB
  ARM: dts: r8a77470: Add HSUSB device nodes
  ARM: dts: iwg23s-sbc: Enable USB USB2.0 Host
  ARM: dts: r8a77470: Add USB2.0 Host (EHCI/OHCI) device
  ARM: dts: iwg23s-sbc: Enable USB Phy[01]
  ARM: dts: r8a77470: Add USB PHY DT support
  ARM: dts: r8a77470: Add VIN support
  ARM: dts: r8a77470: Add PWM support
  ARM: dts: r8a77470: Add HSCIF support
  ARM: dts: alt: Enable USB support
  ARM: dts: rskrza1: Add remaining LEDs
  ARM: dts: rskrza1: Add I2C support
  ARM: dts: iwg23s-sbc: Add HDMI support
  ARM: dts: r8a77470: Add DU support
  ARM: dts: ape6evm: Add NOR FLASH
  ARM: dts: alt: Add DA9063 PMIC node
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm64-dt2-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt

Second Round of Renesas ARM64 Based SoC DT Updates for v5.2

* R-Car H3 (r8a7795), M3-N (r8a77965) and E3 (r8a77990) SoCs
  - Describe CMT devices in DT

* R-Car M3-N (r8a77965) SoC
  - Remove unecessary reg-names of display node

* R-Car V3H (r8a77980) SoC
  - Add missing "renesas,id" property to VIN of device tree

* RZ/G2E (r8a774c0) based CAT874 board
  - Add USB-HOST support

* tag 'renesas-arm64-dt2-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: renesas: r8a77980: Add "renesas,id" to VIN
  arm64: dts: renesas: r8a77965: Remove reg-names of display node
  arm64: dts: renesas: r8a77990: Add CMT device nodes
  arm64: dts: renesas: r8a77965: Add CMT device nodes
  arm64: dts: renesas: r8a7795: Add CMT device nodes
  arm64: dts: renesas: cat874: Add USB-HOST support
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-h3-h5-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Allwinner H3/H5 changes for 5.2

Our usual bunch of changes shared between arm and arm64, the most notable
one being:
  - Fix of improper usage of DT bindings, thanks to the DT validation
  - Add the SID for the H3 and H5
  - New board: RerVision H3-DVK

* tag 'sunxi-h3-h5-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: mapleboard: Remove cd-inverted
  ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI
  ARM: dts: sun8i: h3: bluetooth for Banana Pi M2 Zero board
  ARM: dts: sun8i: h3: Add default dr_mode
  ARM: dts: sun8i: h3: Refactor the pinctrl node names
  ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry
  ARM: dts: sunxi: h3/h5: Add device node for SID
  ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Allwinner arm64 DT changes for 5.2

Our usual bunch of patches, the most notable one being:
  - Fixing the DTC warnings
  - Fix DT bindings not being properly respected, thanks to the DT
    validation
  - New Board: Oceanic 5205, Beelink GS1, Orange Pi3

* tag 'sunxi-dt64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (22 commits)
  arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node
  arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1
  arm64: dts: allwinner: Fix DE2 bus node name
  arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI
  arm64: dts: allwinner: h6: Add MMC1 pins
  arm64: dts: allwinner: h6: Add Orange Pi 3 DTS
  arm64: dts: allwinner: h6: Introduce Beelink GS1 board
  dt-bindings: vendor-prefixes: add AZW
  arm64: dts: allwinner: h6: move MMC pinctrl to dtsi
  arm64: dts: allwinner: h6: Add device node for SID
  arm64: dts: allwinner: a64: Fix the Codec I2S binding
  arm64: dts: allwinner: a64: Add default dr_mode
  arm64: dts: allwinner: Fix pinctrl node names
  arm64: dts: allwinner: a64: Add missing PIO clocks
  arm64: dts: allwinner: a64: Fix display pipeline endpoints
  arm64: dts: allwinner: a64: Fix the TCON output clock
  arm64: dts: allwinner: h6: Add Video Engine node
  arm64: dts: allwinner: a64: Add cross links for the mixers
  arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support
  dt-bindings: Add vendor prefix for oceanic
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Allwinner DT changes for 5.2

This PR is pretty significant, but it been mostly about:
  - Fixing the DTC warnings in most of our DT. We're now down to 2
    warnings, from several thousands.
  - Fixing a good number of minor issues, typos, and so on thanks to the DT
    validation tools
  - Describe the MBUS controller and the special DMA RAM mapping on the A13
  - Add support for the LRADC on the A83t
  - Add support for the I2C bus used for the PMIC on the A33
  - Start using the DT annotation /omit-if-no-ref/ on our pinctrl nodes

* tag 'sunxi-dt-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (65 commits)
  ARM: dts: sun8i: a83t: Enable USB OTG controller on some boards
  ARM: dtsi: axp81x: add USB power supply node
  ARM: dts: sun5i: Reorder pinctrl nodes
  ARM: dts: sun6i: i7: Remove useless property
  ARM: dts: sun4i: lime: Fix the USB PHY ID detect GPIO properties
  ARM: dts: sun4i: protab2: Remove stale pinctrl-names entry
  ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI
  ARM: dts: sun8i: v40: bananapi-m2-berry: Sort device node dereferences.
  ARM: dts: sun5i: Add the MBUS controller
  dt-bindings: sunxi: Add compatible for OrangePi 3 board
  ARM: dts: sun8i: a83t: Add I2C2 pinmux setting for PE pins
  dt-bindings: arm: sunxi: Add Beelink GS1 board
  ARM: dts: sun8i: tbs-a711: Add support for volume keys input
  ARM: dts: sunxi: Add R_LRADC support for A83T
  ARM: dts: sunxi: Improve A33 NAND transfers by using DMA
  ARM: dts: sun8i: tbs-a711: Enable UART2 (for NEO-6M GPS module)
  ARM: dts: sunxi: Remove useless pinctrl nodes
  ARM: dts: sunxi: Remove pinctrl groups setting bias
  ARM: dts: sunxi: Remove useless address and size cells
  ARM: dts: sunxi: Conform to DT spec for NAND controller
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-5.2-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

arm64: tegra: Device tree changes for v5.2-rc1

This contains a bunch of changes all across the board. Perhaps the most
notable introduction here is support for the Jetson Nano Developer Kit.

* tag 'tegra-for-5.2-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: tegra: Remove regulator hacks on Jetson TX2
  arm64: tegra: Enable XUSB on P2771
  arm64: tegra: Add XUSB and pad controller on Tegra186
  arm64: tegra: Add NVIDIA Jetson Nano Developer Kit support
  arm64: tegra: smaug: Move PLL power supplies to XUSB pad controller
  arm64: tegra: jetson-tx1: Move PLL power supplies to XUSB pad controller
  arm64: tegra: Enable command queue for Tegra186 SDMMC4
  arm64: tegra: Fix default tap and trim values
  arm64: tegra: Add supply for temperature sensor on P2888
  arm64: tegra: Enable aconnect, ADMA and AGIC on Jetson TX1
  arm64: tegra: Add L2 cache topology to Tegra210
  arm64: tegra: Enable CPU idle support for Shield
  arm64: tegra: Enable CPU idle support for Smaug
  arm64: tegra: Enable CPU idle support for Jetson TX1
  arm64: tegra: Add CPU idle states properties for Tegra210
  arm64: tegra: Fix timer node for Tegra210
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-5.2-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt

ARM: tegra: Device tree changes for v5.2-rc1

This contains a set of changes to move PLL power supplies to the XUSB
pad controller, which is necessary to ensure the proper sequencing
during boot. Other patches in this set clean up usage of SPDX license
identifiers in device tree files as well as add support for the ACTMON
hardware on Tegra30.

* tag 'tegra-for-5.2-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Add ACTMON support on Tegra30
  ARM: tegra: venice2: Move PLL power supplies to XUSB pad controller
  ARM: tegra: nyan: Move PLL power supplies to XUSB pad controller
  ARM: tegra: jetson-tk1: Move PLL power supplies to XUSB pad controller
  ARM: tegra: apalis: Move PLL power supplies to XUSB pad controller
  ARM: tegra: Remove gratuitous parentheses in SPDX license identifier
  ARM: tegra: Convert to SPDX license tags for Tegra124 Apalis
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.2/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Add am335x pinmux defines and start using them

This series of changes adds a new pinmux instance defines for am335x,
and a new AM33XX_PADCONF macro. And then the rest of the series updates
the dts files to use it.

The reasons for doing this is the pinmux configuration has been hard to
use and read. And we need to do this for eventually for moving to use
values.

This change is done one machine at a time, and can be easily reverted
as needed in case of unexpected trouble. The old macro is still working,
and we're planning to keep it around until we eventually change to use

* tag 'omap-for-v5.2/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (38 commits)
  ARM: dts: am335x: wega: Replaced register offsets with defines
  ARM: dts: am335x: sl50: Replaced register offsets with defines
  ARM: dts: am335x: shc: Replaced register offsets with defines
  ARM: dts: am335x: sbc-t335: Replaced register offsets with defines
  ARM: dts: am335x: sancloud-bbe: Replaced register offsets with defines
  ARM: dts: am335x: phycore-som: Replaced register offsets with defines
  ARM: dts: am335x: pepper: Replaced register offsets with defines
  ARM: dts: am335x: pdu001: Replaced register offsets with defines
  ARM: dts: am335x: pcm-953: Replaced register offsets with defines
  ARM: dts: am335x: osd335x-common: Replaced register offsets with defines
  ARM: dts: am335x: osd3358-sm-red: Replaced register offsets with defines
  ARM: dts: am335x: nano: Replaced register offsets with defines
  ARM: dts: am335x: moxa-uc-8100-me-t: Replaced register offsets with defines
  ARM: dts: am335x: moxa-uc-2101: Replaced register offsets with defines
  ARM: dts: am335x: moxa-uc-2100-common: Replaced register offsets with defines
  ARM: dts: am335x: lxm: Replaced register offsets with defines
  ARM: dts: am335x: igep0033: Replaced register offsets with defines
  ARM: dts: am335x: icev2: Replaced register offsets with defines
  ARM: dts: am335x: evmsk: Replaced register offsets with defines
  ARM: dts: am335x: evm: Replaced register offsets with defines
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'socfpga_dts_updates_for_v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt

SoCFPGA DTS updates for v5.2
- Add base support for Agilex platform
- Add 'cap-mmc-highspeed' Stratix10 and 32-bit SoCFPGA platform
- Increase Stratix10 QSPI support to 100 MHz

* tag 'socfpga_dts_updates_for_v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA
  arm64: dts: stratix10: increase QSPI max frequency to 100MHz
  arm64: dts: stratix10: enable MMC highspeed support
  ARM: dts: socfpga: enable MMC highspeed support
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'ux500-dts-v5.2-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt

Ux500 DTS changes for the v5.2 kernel cycle.
- This adds the MCDE display controller and some displays.
- The Lima MALI-400 driver is added to the kernel, so
  let's add this block to the Ux500 DTS file.

* tag 'ux500-dts-v5.2-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: dts: Ux500: Add MCDE and Samsung display
  ARM: dts: ux500: Add Mali-400
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.2/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Devicetree changes for omap4 and 5 l4 abe interconnect

This series of devicetree changes adds the l4 abe interconnect devices
and moves the devices to their right places in the hierarchy similar
to what we've already done for most l4 devices earlier. We first add
a shared omap4-mcpdm.dtsi to make adding omap4-l4-abe.dtsi easier for
the mcpdm changes. And as earlier, in case of unexpected trouble,
devices can be probed the old way by moving one device at a time to the
old place.

This series of changes depends on the ti-sysc driver changes for handling
the external optional clocks that the mcpdm relies on, and is based on
the related ti-sysc driver changes. Note that this series does not depend
on dropping of the leagcy platform data, but I already had those committed
along with the ti-sysc driver changes and noticed too late.

* tag 'omap-for-v5.2/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (44 commits)
  ARM: dts: Add l4 abe interconnect hierarchy and ti-sysc data for omap5
  ARM: dts: Add l4 abe interconnect hierarchy and ti-sysc data for omap4
  ARM: dts: Add common mcpdm dts file for omap4
  bus: ti-sysc: Add generic enable/disable functions
  ARM: OMAP2+: Drop mcspi platform data for omap4
  ARM: OMAP2+: Drop uart platform data for dra7
  ARM: OMAP2+: Drop gpio platform data for dra7
  ARM: OMAP2+: Drop i2c platform data for dra7
  ARM: OMAP2+: Drop mmc platform data for dra7
  ARM: OMAP2+: Drop uart platform data for omap5
  ARM: OMAP2+: Drop gpio platform data for omap5
  ARM: OMAP2+: Drop i2c platform data for omap5
  ARM: OMAP2+: Drop mmc platform data for omap5
  ARM: OMAP2+: Drop uart platform data for am33xx and am43xx
  ARM: OMAP2+: Drop gpio platform data for am33xx and am43xx
  ARM: OMAP2+: Drop i2c platform data for am33xx and am43xx
  ARM: OMAP2+: Drop mmc platform data for am330x and am43xx
  ARM: OMAP2+: Drop uart platform data for omap4
  ARM: OMAP2+: Drop gpio platform data for omap4
  ARM: OMAP2+: Drop i2c platform data for omap4
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.2/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt

Devicetree changes for omap variants

This series of changes configures dra7 pcie x2 lane mode, configures
am43xx-epos-evm regulators and keypad wakeup source, and uses standard
reset-gpios instead of gpio-reset for n810.

We also need to split dra7 dtsi files for properly supporting dra76x
and am576 as some of the devices are different such as usb and pruss.

* tag 'omap-for-v5.2/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: dra7: Separate AM57 dtsi files
  dt-binding: arm: omap: Add information for AM5748
  ARM: dts: omap2420-n810: Use new CODEC reset pin name
  ARM: dts: am43xx-epos-evm: Add matrix keypad as wakeup source
  ARM: dts: am43xx-epos-evm: Keep DCDC3 regulator on in suspend to memory
  ARM: dts: am43xx-epos-evm: Keep DCDC5 and DCDC6 always on
  ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM64: DT: Hisilicon SoCs DT updates for 5.2

* Hi3660 SoC and related boards:
  - Added DMA support for the uart nodes
  - Added the asp DMA controller node
  - Replaced dma-min-chan with dma-channel-mask to follow the binding

* Hi3670 SoC and related boards:
  - Reused Hi3660 reset to support Hi3670, updated the binding
    document and added dts node
  - Reused Hi3660 MMC controller to support Hi3670, updated the
    binding document and added related nodes to support SD and WiFi
    for the SoC and hikey970 board
  - Added UFS controller node

* tag 'hisi-arm64-dt-for-5.2' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hisilicon: hi3670: Add UFS controller support
  arm64: dts: hi3660: Fixup unofficial dma-min-chan to dma-channel-mask
  arm64: dts: hi3660: Add hisi asp dma device
  arm64: dts: hi3660: Add dma to uart nodes
  arm64: dts: hisilicon: hikey970: Add SD and WiFi support
  arm64: dts: hisilicon: hi3670: Add MMC controller support
  dt-bindings: mmc: Add HI3670 MMC controller binding
  arm64: dts: hisilicon: hi3670: Add reset controller support
  dt-bindings: reset: Add HI3670 reset controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>

arm64: dts: zynqmp: DT changes for v5.2

- Align xlnx-zynqmp-clk.h file name and separate
  binding for clock driver
- Add TI quirks to zynqmp boards

* tag 'zynqmp-dt-for-v5.2' of https://github.com/Xilinx/linux-xlnx:
  arm64: zynqmp: dt: Add TI PHY quirk
  dt-bindings: xilinx: Separate clock binding from firmware doc
  include: dt-binding: clock: Rename zynqmp header file
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt64-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt

Samsung DTS ARM64 changes for v5.2

1. Use proper clock rates for GSCALER module on TM2 boards.
2. Add clocks for local paths on DECON and GSCALER modules of
   Exynos5433.
3. Add Slim SecuritySubSystem to Exynos5433.

* tag 'samsung-dt64-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: dts: exynos: Add SlimSSS to Exynos5433
  arm64: dts: exynos: add DSD/GSD clocks to DECONs and GSCALERs of Exynos5433
  arm64: dts: exynos: configure GSCALER related clocks on TM2
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt

Samsung DTS ARM changes for v5.2

1. Use proper ADC on Exynos4412.
2. Extend the Exynos5420 Arndale Octa board with: CPU cooling maps,
   unused regulators, ADC and UHS-I SD card support.  Beside that adjust
   regulators to proper level and add always-on when needed.
3. Extend the Exynos5260: high speed I2C and proper external interrupts.
   Also fix shared external interrupt line and use better PLL for MMC
   clocks.
4. Fix audio recording (broken around v5.1) and microphone recording
   (since v4.14) on Exynos5422 Odroid XU3 boards.
5. Minor cleanups (stdout-path and bootargs).

* tag 'samsung-dt-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Remove console argument from bootargs
  ARM: dts: exynos: Use stdout-path property instead of console in bootargs
  ARM: dts: exynos: Fix spelling mistake of EXYNOS5420
  ARM: dts: exynos: Fix audio (microphone) routing on Odroid XU3
  ARM: dts: exynos: Always enable necessary APIO_1V8 and ABB_1V8 regulators on Arndale Octa
  ARM: dts: exynos: Extend the eMMC node on Arndale Octa
  ARM: dts: exynos: Add support for UHS-I SD cards on Arndale Octa
  ARM: dts: exynos: Adjust ldo23 and ldo27 to lower levels on Arndale Octa
  ARM: dts: exynos: Fix audio routing on Odroid XU3
  ARM: dts: exynos: Enable ADC on Arndale Octa
  ARM: dts: exynos: Fix interrupt for shared EINTs on Exynos5260
  ARM: dts: exynos: Add interrupts for dedicated EINTs on Exynos5260
  ARM: dts: exynos: Add high speed I2C ports for Exynos5260
  ARM: dts: exynos: Use bustop PLL as the source for MMC clocks on Exynos5260
  ARM: dts: exynos: Order nodes alphabetically in Arndale Octa
  ARM: dts: exynos: Add CPU cooling on Arndale Octa
  ARM: dts: exynos: Add unused PMIC regulators on Arndale Octa board
  ARM: dts: exynos: Use stdout path property on Arndale Octa board
  ARM: dts: exynos: Document regulator used by ADC on Odroid U3
  ARM: dts: exynos: Use ADC for Exynos4x12 on Exynos4412
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'stm32-dt-for-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.2, round 1

Highlights:
----------

MPU part:
 - Add initial support of stm32mp157a-dk1 board:
   This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
   and 512MB of DDR3. Several connections are available on this boards:
   4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...

 - Add initial support of stm32mp157c-dk2 board:
   This board is a "super-set" of stm32mp157a-dk1. It embeds a STM32MP157c SOC
   with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Same connections
   than stm32mp157a-dk1 board are available. Display panel (otm8009a) and
   Murata wifi/BT combo is added.

 - Add and enable SD card support (MMCI variant) on stm32mp157c-ed1/ev1 and
   on stm32mp157a-dk1/dk2 boards.

 - Add and enable PMIC support (STPMIC1 chip) on stm32mp157c-ed1/ev1 and
   on stm32mp157a-dk1/dk2 boards.

 - Add and enable IPCC mailbox support on stm32mp157c-ed1/ev1 and
   on stm32mp157a-dk1/dk2 boards.

 - Add sysconfig clock support on stm32mp157c.
 - Add romem and temperature calibration support on stm32mp157c.
 - Add SPDIFRX support on stm32mp157c.
 - Enable CEC on stm32mp157a-dk1/dk2.

MCU part:
 - Add and enable SD card support (MMCI variant) on stm32h743 eval and disco
   boards.
 - Add romem and temperature calibration support on stm32f429
   (and so stm32f469).
 - Enable stm32f769 clock driver

* tag 'stm32-dt-for-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits)
  ARM: dts: stm32: enable cec on stm32mp157a-dk1 board
  ARM: dts: stm32: add cec pins muxing on stm32mp157
  ARM: dts: stm32: add ltdc pins muxing on stm32mp157
  ARM: dts: stm32: add I2C sleep pins muxing on stm32mp157
  ARM: dts: stm32: add power supply of otm8009a on stm32mp157c-dk2
  ARM: dts: stm32: Enable STM32F769 clock driver
  ARM: dts: stm32: add stpmic1 support on stm32mp157a dk1 board
  ARM: dts: stm32: add stpmic1 support on stm32mp157c ed1 board
  ARM: dts: stm32: add spdfirx pins to stm32mp157c
  ARM: dts: stm32: add spdifrx support on stm32mp157c
  ARM: dts: stm32: Add romem and temperature calibration on stm32f429
  ARM: dts: stm32: Add romem and temperature calibration on stm32mp157c
  ARM: dts: stm32: Add clock on stm32mp157c syscfg
  ARM: dts: stm32: enable IPCC mailbox support on STM32MP157a-dk1
  ARM: dts: stm32: enable IPCC mailbox support on STM32MP157c-ed1
  ARM: dts: stm32: add IPCC mailbox support on STM32MP157c
  ARM: dts: stm32: add sdmmc1 support on stm32mp157a dk1 board
  ARM: dts: stm32: add sdmmc1 support on stm32mp157c ed1 board
  ARM: dts: stm32: add sdmmc1 support on stm32mp157c
  ARM: dts: stm32: add sdmmc1 support on stm32h743i disco board
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'aspeed-5.2-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt

ASPEED device tree updates for 5.2

 - RTC and GFX DRM driver went upstream this cycle

 - Miscellaneous board updates for Facebook and IBM BMCs

* tag 'aspeed-5.2-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
  ARM: dts: aspeed: Add RTC node
  ARM: dts: aspeed: witherspoon: Update BMC partitioning
  ARM: dts: aspeed: cmm: enable iio-hwmon-adc
  ARM: dts: aspeed: tiogapass: Enable VUART
  ARM: dts: aspeed-g5: Add video engine
  ARM: dts: aspeed: Enable the GFX IP
  ARM: dts: aspeed-g5: Add resets and clocks to GFX node
  ARM: dts: aspeed: witherspoon: Enable vhub
  ARM: dts: aspeed: palmetto: Fix flash_memory region
  ARM: dts: aspeed: ast2500: Update flash layout
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm64-dt-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt

Renesas ARM64 Based SoC DT Updates for v5.2

* R-Car Gen3 SoC based Salvator-X and Salvator-XS boards
  - Add GPIO keys support
  - Sort rwdt node alphabetically

* R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
  - Use extended audio DMAC register

* R-Car M3-W (r8a7796) SoC
  - Remove unneeded sound #address/size-cells

* R-Car M3-N (r8a77965) SoC
  - Add SSIU support for audio

* R-Car E3 (r8a77990) and RZ/G2E (r8a774c0) SoCs
  - Remove invalid compatible value for CSI40

* R-Car E3 (r8a77990) SoC
  - Cprrect SPDX license identifier style

* R-Car E3 (r8a77990) based Ebisu board
  - Add BD9571 PMIC with DDR0 backup power config
  - Correct adv7482 hexadecimal register address
  - Add GPIO expander

* R-Car E3 (r8a77990) based Ebisu and D3 (r8a77995) based Draak boards
  - Update bootargs to bring them into line with other R-Car Gen3 boards
  - Enable LVDS1 encoder

* R-Car D3 (r8a77995) based Draak board
  - Correct EthernetAVB phy mode
  - Enable CAN0 and CAN1

* RZ/G2E (r8a774c0) SoC
  - Add CANFD support
  - Correct CPU node style

* RZ/G2E (r8a774c0) and RZ/G2M (r8a774a1) SoCs
  - Add clkp2 clock to CAN nodes

* RZ/G2E (r8a774c0) based EK874 board
  - Add LED, CAN and RTC support

* tag 'renesas-arm64-dt-for-v5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
  arm64: dts: renesas: salvator-common: Add GPIO keys support
  arm64: dts: renesas: use extended audio dmac register
  arm64: dts: renesas: r8a77995: draak: Fix EthernetAVB phy mode to rgmii
  arm64: dts: renesas: salvator-common: Sort node label
  arm64: dts: renesas: Update Ebisu and Draak bootargs
  arm64: dts: renesas: r8a774c0: Add clkp2 clock to CAN nodes
  arm64: dts: renesas: r8a774c0: Add CANFD support
  arm64: dts: renesas: r8a774a1: Add clkp2 clock to CAN nodes
  arm64: dts: renesas: ebisu: Add PMIC DDR0 Backup Power config
  arm64: dts: renesas: r8a77990-ebisu: Add BD9571 PMIC
  arm64: dts: renesas: r8a77990: Remove invalid compatible value for CSI40
  arm64: dts: renesas: r8a774c0: Remove invalid compatible value for CSI40
  arm64: dts: renesas: r8a77995: draak: Enable CAN0, CAN1
  arm64: dts: renesas: r8a774c0-cat874: Add RWDT support
  arm64: dts: renesas: ebisu: Enable VIN5
  arm64: dts: renesas: r8a774c0-cat874: Add LEDs support
  arm64: dts: renesas: r8a774c0-cat874: add RTC support
  arm64: dts: renesas: cat875: Add CAN support
  arm64: dts: renesas: r8a774c0: Fix cpu nodes style
  arm64: dts: renesas: r8a77965: add SSIU support for sound
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v5.2-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt

Core new soc features are hdmi-cec for rk3328, scheduler capacity-values
and emmc cleanups for rk3399. New boards are the OrangePi (rk3399) and
NanoPi NEO4. Both the OrangePi as well as the NanoPC/Pie family also
directly got some additional features added after the boards itself.

The Rock960 family (rock960+ficus) got their power-tree cleaned to match
the schematics and also got hdmi-audio and their gpu enabled.

Mali support also got enabled on the RockPi4 and finally both
rk3328-rock64 and rk3328-roc-cc got some additional features.

* tag 'v5.2-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
  arm64: dts: rockchip: Decrease emmc-phy's drive impedance on rk3399-puma
  arm64: dts: rockchip: Define drive-impedance-ohm for RK3399's emmc-phy.
  arm64: dts: rockchip: Disable DCMDs on RK3399's eMMC controller.
  arm64: dts: rockchip: Add nanopi4 ethernet phy
  arm64: dts: rockchip: Add PWM fan for NanoPC-T4
  arm64: dts: rockchip: Add the fusb typec manager to rk3399-orangepi
  arm64: dts: rockchip: Specify vid supply for the rk3399-orangepi compass (AK09911)
  arm64: dts: rockchip: Fix clock names and add missing supplies for bluetooth on rk3399-orangepi
  arm64: dts: rockchip: Add 12V DCIN regulator to rk3399-ficus
  arm64: dts: rockchip: Rename vcc_sys into vcc5v0_sys on rk3399-rock960
  arm64: dts: rockchip: Add Nanopi NEO4 initial support
  arm64: dts: rockchip: enable hdmi audio out for rk3399-rockpro64
  arm64: dts: rockchip: Add support for the Orange Pi RK3399 board.
  arm64: dts: rockchip: enable mali on rock960 boards
  arm64: dts: rockchip: enable mali on Rock Pi 4
  arm64: dts: rockchip: add rk3328-roc-cc cpu-supply entries for all cpu nodes
  arm64: dts: rockchip: give some life to the rk3328-roc-cc leds
  arm64: dts: rockchip: add #sound-dai-cells to HDMI of rk3328
  arm64: dts: rockchip: add ir-receiver node on rk3328-rock64
  arm64: dts: rockchip: add leds node on rk3328-rock64
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v5.2-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt

Quite a bit of love for the rk3288-veyron chromeos devices and a number
of cleanups for rk3288 from that area, hdmi support for the old rk3066
a small rv1108-eglin-r1 cleanup and wifi+hdmi-cec for the tinker board.

* tag 'v5.2-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: enable vop0 and hdmi nodes to rk3066a-mk808
  ARM: dts: rockchip: add rk3066 hdmi nodes
  ARM: dts: rockchip: Add device tree for rk3288-veyron-mighty
  dt-bindings: ARM: dts: rockchip: Add bindings for rk3288-veyron-mighty
  ARM: dts: rockchip: Add vdd_logic to rk3288-veyron
  ARM: dts: rockchip: Add dvs-gpios to rk3288-veyron-jerry
  ARM: dts: rockchip: Add rk3288-veyron-jerry rev 10-15
  dt-bindings: ARM: dts: rockchip: Add rk3288-veyron-jerry rev 10-15
  ARM: dts: rockchip: Fix gic/efuse sort ordering for rk3288
  ARM: dts: rockchip: Enable WiFi on rk3288-tinker
  ARM: dts: rockchip: add grf reference in rk3288 tsadc node
  ARM: dts: rockchip: Enable HDMI CEC on rk3288-tinker-s
  ARM: dts: rockchip: remove disable-wp from rv1108-elgin-r1 emmc node
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt

ARM: dts: Amlogic updates for v5.2
 - add GPIO line names for odroid-c1 boards
 - support internal clock measure driver

* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8b: odroidc1: add the GPIO line names
  ARM: dts: meson8b: add the internal clock measurer
  ARM: dts: meson8: add the internal clock measurer
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt

arm64: dts: Amlogic updates for v5.2

Highlights
- new board: SEI Robotics 510, based on S905X2 SoC (G12A)
- enable more periphearls for S905X2 based boards

* tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-g12a: Add CMA reserved memory
  arm64: dts: meson-g12a-x96-max: Enable BT Module
  arm64: dts: meson-g12a-x96-max: add regulators
  arm64: dts: meson-g12a-sei510: add regulators
  arm64: dts: meson-g12a-x96-max: add uart_AO pinctrl
  arm64: dts: meson-g12a-sei510: add uart_AO pinctrl
  arm64: dts: meson-g12a-u200: add uart_AO pinctrl
  arm64: dts: meson: g12a: Add UART A, B & C nodes and pins
  arm64: dts: meson: g12a: add reset controller
  arm64: dts: meson: g12a: add uart_ao_a pinctrl
  arm64: dts: meson: g12a: add pinctrl support controllers
  arm64: dts: meson: g12a: Add AO Clock + Reset Controller support
  arm64: dts: meson-gxm-nexbox-a1: Enable USB
  arm64: dts: meson: g12a: add efuse
  arm64: dts: meson: g12a: add secure monitor
  arm64: dts: meson-gxl-s905d-phicomm-n1: add status LED
  arm64: dts: meson-g12a: Add AO Secure node
  arm64: dts: Add SEI Robotics SEI510 Board
  vendor-prefixes: Add prefix for Shenzhen SEI Robotics Co., Ltd
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the Audio DSP (ADSP) and Compute DSP (CDSP) nodes for TrustZone
based remoteproc, supporting booting these cores on e.g. the MTP, and
enable the same for the MTP.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>

Define the rmtfs memory node. As the memory region specified in version
10 of the memory map is only 1MB a chunk of unallocated memory is
chosen.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>

Update existing and add missing regions to the reserved memory map, as
described in version 10.
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>

Wire up the reset controller in the Qcom UFS controller for the PHY.
This will be used to toggle PHY reset during initialization of the PHY.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>

Add #io-channel-cells to list of required properties. Needed to be
able to reference that node by phandle.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Specify #io-channel-cells in ADC nodes. Needed to be able to reference
them by phandle.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>