- 28 Jul, 2017 40 commits
-
-
Brian Norris authored
It's possible for some control interfaces (e.g., scans, set freq) to be active after we've stopped our main work queue and the netif TX queues. These don't get completely shut out until we've unregistered the wdevs and wiphy. So let's only free command buffers and poison our lists after wiphy_unregister(). This resolves various use-after-free issues seen when resetting the device. Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Brian Norris authored
In general, it's helpful to use the same code for device removal as for device reset, as this tends to have fewer bugs. Let's move the wiphy unregistration code into the common reset and removal code. In particular, it's very hard to properly handle the reset sequence when something fails. Currently, if mwifiex_reinit_sw() fails, we've failed to unregister the associated wiphy, and so running something as simple as "iw phy" can trigger an OOPS, as the wiphy still has hooks back into freed mwifiex data structures. For example, KASAN complained: [... see reset fail for other reasons ...] [ 1184.821158] mwifiex_pcie 0000:01:00.0: info: dnld wifi firmware from 174948 bytes [ 1186.870914] mwifiex_pcie 0000:01:00.0: info: FW download over, size 608396 bytes [ 1187.685990] mwifiex_pcie 0000:01:00.0: WLAN FW is active [ 1187.692673] mwifiex_pcie 0000:01:00.0: cmd_wait_q terminated: -512 [ 1187.699075] mwifiex_pcie 0000:01:00.0: info: _mwifiex_fw_dpc: unregister device [ 1187.713476] mwifiex: Failed to bring up adapter: -5 [ 1187.718644] mwifiex_pcie 0000:01:00.0: reinit failed: -5 [... run `iw phy` ...] [ 1212.902419] ================================================================== [ 1212.909806] BUG: KASAN: use-after-free in mwifiex_cfg80211_get_antenna+0x54/0xfc [mwifiex] at addr ffffffc0ad1a8028 [ 1212.920246] Read of size 1 by task iw/3127 [...] [ 1212.934946] page dumped because: kasan: bad access detected [...] [ 1212.950665] Call trace: [ 1212.953148] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190 [ 1212.958572] [<ffffffc00020a96c>] show_stack+0x20/0x28 [ 1212.963648] [<ffffffc0005ce18c>] dump_stack+0xa4/0xcc [ 1212.968723] [<ffffffc0003c4430>] kasan_report+0x378/0x500 [ 1212.974140] [<ffffffc0003c3358>] __asan_load1+0x44/0x4c [ 1212.979462] [<ffffffbffc2e8360>] mwifiex_cfg80211_get_antenna+0x54/0xfc [mwifiex] [ 1212.987131] [<ffffffbffc084fc4>] nl80211_send_wiphy+0x75c/0x2de0 [cfg80211] [ 1212.994246] [<ffffffbffc094f60>] nl80211_dump_wiphy+0x32c/0x438 [cfg80211] [ 1213.001149] [<ffffffc000ab6404>] genl_lock_dumpit+0x48/0x64 [ 1213.006746] [<ffffffc000ab3474>] netlink_dump+0x178/0x398 [ 1213.012171] [<ffffffc000ab3d18>] __netlink_dump_start+0x1bc/0x260 [...] This all goes away if we just tear down the wiphy on the way down, and set it back up if/when we bring the device back up. Signed-off-by:
-
Brian Norris authored
In rogue cases (due to other bugs) it's possible we try to process an old command response *after* resetting the device. This could trigger a double-free (or the SKB can get reallocated elsewhere...causing other memory corruptions) in mwifiex_pcie_process_cmd_complete(). For safety (and symmetry) let's always NULL out the command buffer as we free it up. We're already doing this for the command response buffer. Signed-off-by:
-
Brian Norris authored
When resetting the device, we might have queued up interrupts that didn't get a chance to finish processing. We really don't need to handle them at this point; we just want to make sure they don't cause us to try to process old commands from before the device was reset. Signed-off-by:
-
Brian Norris authored
When PCIe FLR code was added, it explicitly copy-and-pasted much of mwifiex_remove_card() into mwifiex_shutdown_sw(). This is unnecessary, as almost all of the code should be reused. Let's reunite what we can for now. The only functional changes for now: * call netif_device_detach() in the remove() code path -- this wasn't done before, but it really should be a no-op, when the device is getting totally unregistered soon anyway * call the ->down_dev() driver callback only after we've finished all SW teardown -- this should have no significant effect, since the only user (pcie.c) does very minimal work there, and it doesn't matter that we reorder this Signed-off-by:
-
Amitkumar Karwar authored
u32 pointer is changed to u16 and filled the value. Problem is solved by using local temporary variable. Below static checker warning was reported. drivers/net/wireless/rsi/rsi_91x_usb.c:400 rsi_usb_master_reg_read() warn: passing casted pointer 'value' to 'rsi_usb_reg_read()' 32 vs 16. Fixes: b97e9b94 ("rsi: Add new host interface operations") Signed-off-by:Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
-
Amitkumar Karwar authored
These checks are required. Otherwise we may end up getting memory corruption if invalid length is passed. Fixes: b97e9b94 ("rsi: Add new host interface operations") Signed-off-by:
-
Amitkumar Karwar authored
4 bytes is fixed size for reading or writing USB register. We will use a macro instead of hardcoding this. Fixes: b97e9b94 ("rsi: Add new host interface operations") Signed-off-by:
-
Prameela Rani Garnepudi authored
Below regulatory changes are included this patch * Country code is saved as it will be used in bgscan. * Region codes are mapped according to RSI region codes. * Radar flag settings are moved under the check if 5GHZ band is enabled. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
-
Prameela Rani Garnepudi authored
When interface is down it is better to stop all RX packets to host. 0xffff will block all packets to host. Signed-off-by:
-
Prameela Rani Garnepudi authored
Device specific descriptor for each TX packet is prepared on top of skb data address. This descriptor should be pulled out before indicating the TX status to mac80211. Signed-off-by:
-
Prameela Rani Garnepudi authored
TX command frame block/unblock data is modified to use common descriptor structure. Signed-off-by:
-
Prameela Rani Garnepudi authored
Data queues should be unblocked after station add notify frame is sent and should be blocked after station delete notify is sent. Signed-off-by:
-
Prameela Rani Garnepudi authored
When Short Gaurd Interval is enabled bit 9 is set in rate. Otherwise it should not be set. Added missing 'else' case in this patch. Signed-off-by:
-
Prameela Rani Garnepudi authored
Broadcast bit to be set for broadcast and multicast packets. For remove_key, tx and rx mic need not be filled. Signed-off-by:
-
Prameela Rani Garnepudi authored
TX command frame set_key is modified to use common descriptor structure. Signed-off-by:
-
Prameela Rani Garnepudi authored
VAP capablities frame configured to device is modified to use common descriptor structure. Signed-off-by:
-
Prameela Rani Garnepudi authored
TX command frame set_channel is modified to use common descriptor structure. Also DFS channel indication to firmware is added in the descriptor for dfs channels configuration. Signed-off-by:
-
Prameela Rani Garnepudi authored
Baseband RF programming frame configured to device is modified to use common descriptor structure. Signed-off-by:
-
Prameela Rani Garnepudi authored
AMPDU aggregation parameters frame configured to device is modified to use common descriptor structure. Signed-off-by:
-
Prameela Rani Garnepudi authored
TX command frame peer notify is updated to use common descriptor structure. MPDU density value added to the frame. Signed-off-by:
-
Prameela Rani Garnepudi authored
The function rsi_mgmt_pkt_to_core() is for passing the 802.11 management frames to mac80211. So, it is unnecessary to check again for the frame type 802.11 management in this function. It can be checked before passing to this function. Signed-off-by:
-
Prameela Rani Garnepudi authored
Radio capabilities frame is updated to use common descriptor structure. Also, few changes to this frame is done like hardware queues are increase to 12 from 8, default channel number is included. Signed-off-by:
-
Prameela Rani Garnepudi authored
For all TX command packets immediate wakeup bit needs to be set in descriptor. This will make sure device will wakeup if it is in any sleep state. Priority of the packet is also set. Signed-off-by:
-
Prameela Rani Garnepudi authored
All internal management packets (command packets) use some common fields and some packet specific fields for packet descriptors. This patch adds some common structures which are needed for all command packets. Signed-off-by:
-
Karun Eagalapati authored
We have now added separate lock for Rx. This lock is used to protect tx path only Signed-off-by:
Karun Eagalapati <karun256@gmail.com> Signed-off-by:
-
Karun Eagalapati authored
Deadlock issue is observed during our stress tests. The root cause for the issue is same lock is used between tx and rx threads. This patch adds a separate mutex lock for rx thread to resolve the problem. Signed-off-by:
-
Karun Eagalapati authored
Newer firmware sends information about number of blocks through interrupt only. We don't need to read extra register for this. This patch adds needed driver changes for this enhancment. The change here is backward compatible Signed-off-by:
-
Karun Eagalapati authored
SDIO host is already claimed in our interrupt handler. Some lower level APIs claims host while performing SDIO read or write operations. Let's use sdio_irq_task variable to check if we are in interrupt context and claim/release the host accordingly. Signed-off-by:
-
Karun Eagalapati authored
The variable in_sdio_litefi_irq is renamed to sdio_irq_task, as it is more relevant here. Signed-off-by:
-
Pavani Muthyala authored
Data packet descriptor preparation code is moved a separate function. Signed-off-by:
Pavani Muthyala <pavani.muthyala@redpinesignals.com> Signed-off-by:
-
Pavani Muthyala authored
This patch covers some enhancements in data packet descriptor preparation especially for EAPOL, multicast/broadcast packets. Signed-off-by:
-
Pavani Muthyala authored
Currently this descriptor is prepared with the help of __le16 pointer. This patch makes use of a structure to prepare the descriptor in a cleaner way. Signed-off-by:
-
Prameela Rani Garnepudi authored
Management descriptor preparation is move to a separate function as it will be called from a different context in upcoming patches. Signed-off-by:
-
Pavani Muthyala authored
Currently this descriptor is prepared with the help of __le16 pointer. This patch makes use of a structure to prepare the descriptor in a cleaner way. Signed-off-by:
-
Karun Eagalapati authored
immediate wakeup bit is set while sending internal management frame to the firmware. Signed-off-by:
-
Karun Eagalapati authored
Till now only management packets were handled. Let's enhance the logic for choosing endpoint to accommodate other packets. Signed-off-by:
-
Karun Eagalapati authored
These endpoints are for WLAN and BT protocols. Signed-off-by:
-
Amitkumar Karwar authored
Maximum valid queue number is 0x5. So anding with 0x7 should be ok here. Signed-off-by:
-
Karun Eagalapati authored
USB headroom is added while submitting the data to URB as per firmware's requirement. This logic is moved to rsi_usb_card_write() so that caller need not worry about it. Signed-off-by:
-
