- 08 Jun, 2016 40 commits
-
-
Gavin Shan authored
commit affeb0f2 upstream. The function eeh_pe_reset_and_recover() is used to recover EEH error when the passthrough device are transferred to guest and backwards, meaning the device's driver is vfio-pci or none. When the driver is vfio-pci that provides error_detected() error handler only, the handler simply stops the guest and it's not expected behaviour. On the other hand, no error handlers will be called if we don't have a bound driver. This ignores the error handler in eeh_pe_reset_and_recover() that reports the error to device driver to avoid the exceptional behaviour. Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices") Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hari Bathini authored
commit 8ed8ab40 upstream. Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Signed-off-by:
Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
-
Willy Tarreau authored
commit 759c0114 upstream. On no-so-small systems, it is possible for a single process to cause an OOM condition by filling large pipes with data that are never read. A typical process filling 4000 pipes with 1 MB of data will use 4 GB of memory. On small systems it may be tricky to set the pipe max size to prevent this from happening. This patch makes it possible to enforce a per-user soft limit above which new pipes will be limited to a single page, effectively limiting them to 4 kB each, as well as a hard limit above which no new pipes may be created for this user. This has the effect of protecting the system against memory abuse without hurting other users, and still allowing pipes to work correctly though with less data at once. The limit are controlled by two new sysctls : pipe-user-pages-soft, and pipe-user-pages-hard. Both may be disabled by setting them to zero. The default soft limit allows the default number of FDs per process (1024) to create pipes of the default size (64kB), thus reaching a limit of 64MB before starting to create only smaller pipes. With 256 processes limited to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB = 1084 MB of memory allocated for a user. The hard limit is disabled by default to avoid breaking existing applications that make intensive use of pipes (eg: for splicing). Reported-by: socketpair@gmail.com Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Mitigates: CVE-2013-4312 (Linux 2.0+) Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Moritz Muehlenhoff <moritz@wikimedia.org> Signed-off-by:
-
Zhao Qiang authored
commit 11ca2b7a upstream. New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart. So add it. Signed-off-by:
Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by:
-
Oleg Nesterov authored
commit bf959931 upstream. The following program (simplified version of generated by syzkaller) #include <pthread.h> #include <unistd.h> #include <sys/ptrace.h> #include <stdio.h> #include <signal.h> void *thread_func(void *arg) { ptrace(PTRACE_TRACEME, 0,0,0); return 0; } int main(void) { pthread_t thread; if (fork()) return 0; while (getppid() != 1) ; pthread_create(&thread, NULL, thread_func, NULL); pthread_join(thread, NULL); return 0; } creates an unreapable zombie if /sbin/init doesn't use __WALL. This is not a kernel bug, at least in a sense that everything works as expected: debugger should reap a traced sub-thread before it can reap the leader, but without __WALL/__WCLONE do_wait() ignores sub-threads. Unfortunately, it seems that /sbin/init in most (all?) distributions doesn't use it and we have to change the kernel to avoid the problem. Note also that most init's use sys_waitid() which doesn't allow __WALL, so the necessary user-space fix is not that trivial. This patch just adds the "ptrace" check into eligible_child(). To some degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is mostly ignored when the tracee reports to debugger. Or WSTOPPED, the tracer doesn't need to set this flag to wait for the stopped tracee. This obviously means the user-visible change: __WCLONE and __WALL no longer have any meaning for debugger. And I can only hope that this won't break something, but at least strace/gdb won't suffer. We could make a more conservative change. Say, we can take __WCLONE into account, or !thread_group_leader(). But it would be nice to not complicate these historical/confusing checks. Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Jan Kratochvil <jan.kratochvil@redhat.com> Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com> Cc: Pedro Alves <palves@redhat.com> Cc: Roland McGrath <roland@hack.frob.com> Cc: <syzkaller@googlegroups.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Stefan Bader authored
commit 4b50bcc7 upstream. Since commit 92923ca3 ("mm: meminit: only set page reserved in the memblock region") the reserved bit is set on reserved memblock regions. However start and end address are passed as unsigned long. This is only 32bit on i386, so it can end up marking the wrong pages reserved for ranges at 4GB and above. This was observed on a 32bit Xen dom0 which was booted with initial memory set to a value below 4G but allowing to balloon in memory (dom0_mem=1024M for example). This would define a reserved bootmem region for the additional memory (for example on a 8GB system there was a reverved region covering the 4GB-8GB range). But since the addresses were passed on as unsigned long, this was actually marking all pages from 0 to 4GB as reserved. Fixes: 92923ca3 ("mm: meminit: only set page reserved in the memblock region") Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.comSigned-off-by:
Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
-
Tiffany Lin authored
commit baf43c6e upstream. In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved filed of v4l2_create_buffers filled with zero Reserved field is filled with zero in v4l_create_bufs. This patch copy reserved field of v4l2_create_buffer from kernel space to user space Signed-off-by:
Tiffany Lin <tiffany.lin@mediatek.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Prarit Bhargava authored
commit ad67b437 upstream. b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with the PCI spec. But it didn't do anything for expansion ROM BARs, so we still try to size them, resulting in warnings like this on Broadwell-EP: pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref] Move the non-compliant BAR check from __pci_read_base() up to pci_read_bases() so it applies to the expansion ROM BAR as well as to BARs 0-5. Note that direct callers of __pci_read_base(), like sriov_init(), will now bypass this check. We haven't had reports of devices with broken SR-IOV BARs yet. [bhelgaas: changelog] Fixes: b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Andrew Jeffery authored
commit 71324fdc upstream. The range is registered into a linked list which can be referenced throughout the lifetime of the driver. Ensure the range's memory is useful for the same lifetime by adding it to the driver's private data structure. The bug was introduced in the driver's initial commit, which was present in v3.10. Fixes: f0b9a7e5 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC") Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Acked-by:
Tomasz Figa <tomasz.figa@gmail.com> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Martin Sperl authored
commit 997f16bd upstream. Current clamping of a normal divider allows a value < 1 to be valid. A divider of < 1 would actually only be possible if we had a PLL... So this patch clamps the divider to 1. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
-
Martin Sperl authored
commit 6727f086 upstream. bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control register, which may lose the other bits that are currently set by the clock dividers. It also now locks during the read/modify/write cycle of both registers. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by:
-
Vladimir Zapolskiy authored
commit cb0ceaf7 upstream. The clk_register() function returns a valid pointer to struct clk or ERR_PTR() error code, this makes a check for returned NULL value useless and may lead to oops on error path. Signed-off-by:
Vladimir Zapolskiy <vz@mleia.com> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: bcc5fd49 ("clk: at91: add a driver for the h32mx clock") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Eric Anholt authored
commit e708b383 upstream. In poweroff, we set the reset bit and the power down bit, but only managed to unset the reset bit for poweron. This meant that if HDMI did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the PLLH (that had been on at boot time) and never recover. Signed-off-by:
-
Daniel Lezcano authored
commit e7387da5 upstream. Commit 0b89e9aa (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) rightfully fixed a regression by letting the coupled idle state framework to handle local interrupt enabling when the CPU is exiting an idle state. The current code checks if the idle state is coupled and, if so, it will let the coupled code to enable interrupts. This way, it can decrement the ready-count before handling the interrupt. This mechanism prevents the other CPUs from waiting for a CPU which is handling interrupts. But the check is done against the state index returned by the back end driver's ->enter functions which could be different from the initial index passed as parameter to the cpuidle_enter_state() function. entered_state = target_state->enter(dev, drv, index); [ ... ] if (!cpuidle_state_is_coupled(drv, entered_state)) local_irq_enable(); [ ... ] If the 'index' is referring to a coupled idle state but the 'entered_state' is *not* coupled, then the interrupts are enabled again. All CPUs blocked on the sync barrier may busy loop longer if the CPU has interrupts to handle before decrementing the ready-count. That's consuming more energy than saving. Fixes: 0b89e9aa (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> [ rjw: Subject & changelog ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
-
Ulf Hansson authored
commit 0ae3aeef upstream. As pm_runtime_set_active() may fail because the device's parent isn't active, we can end up executing the ->runtime_resume() callback for the device when it isn't allowed. Fix this by invoking pm_runtime_set_active() before running the callback and let's also deal with the error code. Fixes: 37f20416 (PM: Add pm_runtime_suspend|resume_force functions) Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
-
Ville Syrjälä authored
commit 36e6d081 upstream. GPIO lookup tables are supposed to be zero terminated. Let's do that and avoid accidentally walking off the end. Fixes: 61dd2ca2 ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by:
Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Heikki Krogerus authored
commit 41a3da2b upstream. All configurations are lost and the registers will have default values when the hardware is suspended and resumed, so saving the private register space context on suspend, and restoring it on resume. Fixes: 4b45efe8 (mfd: Add support for Intel Sunrisepoint LPSS devices) Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
-
Akshay Bhat authored
commit 7a18afe8 upstream. On ads7828 the internal reference defaults to off upon power up. When using internal reference, it needs to be turned on and the voltage needs to settle before normal conversion cycle can be started. Hence perform a dummy read in the probe to enable the internal reference allowing the voltage to settle before performing a normal read. Without this fix, the first read from the ADC when using internal reference always returns incorrect data. Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 78cbccd3 upstream. When KDUMP is triggered the driver first talks to the firmware in INTX mode, but the adapter firmware is still in MSIX mode. Therefore the first driver command hangs since the driver is waiting for an INTX response and firmware gives a MSIX response. If when the OS is installed on a RAID drive created by the adapter KDUMP will hang since the driver does not receive a response in sync mode. Fixed by: Change the firmware to INTX mode if it is in MSIX mode before sending the first sync command. Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by:
-
wang yanqing authored
commit cf968937 upstream. We can't use kfree_skb in irq disable context, because spin_lock_irqsave make sure we are always in irq disable context, use dev_kfree_skb_irq instead of kfree_skb is better than dev_kfree_skb_any. This patch fix below kernel warning: [ 7612.095528] ------------[ cut here ]------------ [ 7612.095546] WARNING: CPU: 3 PID: 4460 at kernel/softirq.c:150 __local_bh_enable_ip+0x58/0x80() [ 7612.095550] Modules linked in: rtl8723be x86_pkg_temp_thermal btcoexist rtl_pci rtlwifi rtl8723_common [ 7612.095567] CPU: 3 PID: 4460 Comm: ifconfig Tainted: G W 4.4.0+ #4 [ 7612.095570] Hardware name: LENOVO 20DFA04FCD/20DFA04FCD, BIOS J5ET48WW (1.19 ) 08/27/2015 [ 7612.095574] 00000000 00000000 da37fc70 c12ce7c5 00000000 da37fca0 c104cc59 c19d4454 [ 7612.095584] 00000003 0000116c c19d4784 00000096 c10508a8 c10508a8 00000200 c1b42400 [ 7612.095594] f29be780 da37fcb0 c104ccad 00000009 00000000 da37fcbc c10508a8 f21f08b8 [ 7612.095604] Call Trace: [ 7612.095614] [<c12ce7c5>] dump_stack+0x41/0x5c [ 7612.095620] [<c104cc59>] warn_slowpath_common+0x89/0xc0 [ 7612.095628] [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80 [ 7612.095634] [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80 [ 7612.095640] [<c104ccad>] warn_slowpath_null+0x1d/0x20 [ 7612.095646] [<c10508a8>] __local_bh_enable_ip+0x58/0x80 [ 7612.095653] [<c16b7d34>] destroy_conntrack+0x64/0xa0 [ 7612.095660] [<c16b300f>] nf_conntrack_destroy+0xf/0x20 [ 7612.095665] [<c1677565>] skb_release_head_state+0x55/0xa0 [ 7612.095670] [<c16775bb>] skb_release_all+0xb/0x20 [ 7612.095674] [<c167760b>] __kfree_skb+0xb/0x60 [ 7612.095679] [<c16776f0>] kfree_skb+0x30/0x70 [ 7612.095686] [<f81b869d>] ? rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci] [ 7612.095692] [<f81b869d>] rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci] [ 7612.095698] [<f81b87f9>] rtl_pci_start+0x19/0x190 [rtl_pci] [ 7612.095705] [<f81970e6>] rtl_op_start+0x56/0x90 [rtlwifi] [ 7612.095712] [<c17e3f16>] drv_start+0x36/0xc0 [ 7612.095717] [<c17f5ab3>] ieee80211_do_open+0x2d3/0x890 [ 7612.095725] [<c16820fe>] ? call_netdevice_notifiers_info+0x2e/0x60 [ 7612.095730] [<c17f60bd>] ieee80211_open+0x4d/0x50 [ 7612.095736] [<c16891b3>] __dev_open+0xa3/0x130 [ 7612.095742] [<c183fa53>] ? _raw_spin_unlock_bh+0x13/0x20 [ 7612.095748] [<c1689499>] __dev_change_flags+0x89/0x140 [ 7612.095753] [<c127c70d>] ? selinux_capable+0xd/0x10 [ 7612.095759] [<c1689589>] dev_change_flags+0x29/0x60 [ 7612.095765] [<c1700b93>] devinet_ioctl+0x553/0x670 [ 7612.095772] [<c12db758>] ? _copy_to_user+0x28/0x40 [ 7612.095777] [<c17018b5>] inet_ioctl+0x85/0xb0 [ 7612.095783] [<c166e647>] sock_ioctl+0x67/0x260 [ 7612.095788] [<c166e5e0>] ? sock_fasync+0x80/0x80 [ 7612.095795] [<c115c99b>] do_vfs_ioctl+0x6b/0x550 [ 7612.095800] [<c127c812>] ? selinux_file_ioctl+0x102/0x1e0 [ 7612.095807] [<c10a8914>] ? timekeeping_suspend+0x294/0x320 [ 7612.095813] [<c10a256a>] ? __hrtimer_run_queues+0x14a/0x210 [ 7612.095820] [<c1276e24>] ? security_file_ioctl+0x34/0x50 [ 7612.095827] [<c115cef0>] SyS_ioctl+0x70/0x80 [ 7612.095832] [<c1001804>] do_fast_syscall_32+0x84/0x120 [ 7612.095839] [<c183ff91>] sysenter_past_esp+0x36/0x55 [ 7612.095844] ---[ end trace 97e9c637a20e8348 ]--- Signed-off-by:
Wang YanQing <udknight@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
wang yanqing authored
commit 873ffe15 upstream. In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), the tests for enter/exit power-save mode were inverted. With this change applied, the wifi connection becomes much more stable. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by:
-
Larry Finger authored
commit baa17022 upstream. The previous patch added an option to rtl8723be to manually select the antenna for those cases when only a single antenna is present, and the on-board EEPROM is incorrectly programmed. This patch implements the necessary changes in the Bluetooth coexistence driver. Signed-off-by:
-
Larry Finger authored
commit c18d8f50 upstream. A number of new laptops have been delivered with only a single antenna. In principle, this is OK; however, a problem arises when the on-board EEPROM is programmed to use the other antenna connection. The option of opening the computer and moving the connector is not always possible as it will void the warranty in some cases. In addition, this solution breaks the Windows driver when the box dual boots Linux and Windows. A fix involving a new module parameter has been developed. This commit adds the new parameter and implements the changes needed for the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
commit f1925d78 upstream. In case of timeout during read operation, the exit path lacked PM runtime put. This could lead to unbalanced runtime PM usage counter thus leaving the device in an active state. Fixes: d7fd6075 ("hwrng: exynos - Add timeout for waiting on init done") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Anilkumar Kolli authored
commit 4ad24a9d upstream. It is observed that while loading and unloading ath10k modules in an infinite loop, before ath10k_core_start() completion HTT rx frames are received, while processing these frames, dereferencing the arvifs list code is getting hit before initilizing the arvifs list, causing a kernel panic. This patch initilizes the arvifs list before initilizing htt. Fixes the below issue: [<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core]) [<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core]) [<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core]) [<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core]) [<c0234100>] (tasklet_action+0x8c/0xec) [<c0234100>] (tasklet_action) [<c02337c0>] (__do_softirq+0xf8/0x228) [<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90) Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008) ---[ end trace 71de5c2e011dbf56 ]--- Kernel panic - not syncing: Fatal exception in interrupt Fixes: 500ff9f9 ("ath10k: implement chanctx API") Signed-off-by:
Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by:
-
Rajkumar Manoharan authored
commit 1ce8c148 upstream. Upon firmware assert, restart work will be triggered so that mac80211 will reconfigure the driver. An issue is reported that after restart work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info for operating channel. During reconfigure, since mac80211 already has valid channel context for given radio, channel context iteration return num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning channel context to rx_channel when driver restart is in progress. Signed-off-by:
Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by:
-
Rajkumar Manoharan authored
commit 8a75fc54 upstream. commit 166de3f1 ("ath10k: remove supported chain mask") had revealed an issue on monitor mode. Configuring NSS upon monitor interface creation is causing target assert in all qca9888x and qca6174 firmware. Firmware assert issue can be reproduced by below sequence even after reverting commit 166de3f1 ("ath10k: remove supported chain mask"). ip link set wlan0 down iw wlan0 set type monitor iw phy0 set antenna 7 ip link set wlan0 up This issue is originally reported on qca9888 with 10.1 firmware. Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation") Reported-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
-
Anilkumar Kolli authored
commit 9ddc486a upstream. It is observed that, we are disabling the packet log if we write same value to the pktlog_filter for the second time. Always enable pktlogs on non zero filter. Fixes: 90174455 ("ath10k: add support to configure pktlog filter") Signed-off-by:
-
Vittorio Gambaletta (VittGam) authored
commit 0f9edcdd upstream. The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity (active high instead of active low). The same PCI Subsystem ID is used by both cards, which are based on the same Atheros MB92 design. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Signed-off-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by:
-
Vittorio Gambaletta (VittGam) authored
commit cd84042c upstream. The LED can be active high instead of active low on some hardware. Add the led_active_high module parameter. It defaults to -1 to obey platform data as before. Setting the parameter to 1 or 0 will force the LED respectively active high or active low. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Signed-off-by:
-
Alexander Kurz authored
commit 3397c2c4 upstream. A new element got inserted into enum mx35_clks with commit 3713e3f5 ("clk: imx35: define two clocks for rtc"). This insertion shifted most nummerical clock assignments to a new nummerical value which in turn rendered most hardcoded nummeric values in imx35.dtsi incorrect. Restore the existing order by moving the newly introduced clock to the end of the enum. Update the dts documentation accordingly. Signed-off-by:
Alexander Kurz <akurz@blala.de> Fixes: 3713e3f5 ("clk: imx35: define two clocks for rtc") Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Marek Szyprowski authored
commit 330d1276 upstream. MAX8997 PMIC requires interrupt and fails probing without it. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Fixes: d105f0b1 ("ARM: dts: Add basic dts file for Samsung Trats board") [k.kozlowski: Write commit message, add CC-stable] Signed-off-by:
-
Florian Vallee authored
commit b1f3a3b0 upstream. Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were wrongly linked to PIN_PD23). Signed-off-by:
Florian Vallee <fvallee@eukrea.fr> Fixes: 7f16cb67 ("ARM: at91/dt: add sama5d2 pinmux") [nicolas.ferre@atmel.com: add commit message, changed subject] Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Imre Kaloz authored
commit 9800917c upstream. Some of the GPIO configs were wrong in the submitted DTS files, this patch fixes all affected boards. Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com>
-
Ricky Liang authored
commit affa80bd upstream. When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS ioctl needs to be treated with special care, as it has the pointer size encoded in the command. Signed-off-by:
Ricky Liang <jcliang@chromium.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Mark Brown authored
commit d3030d11 upstream. The ak4642 driver is using a regmap cache sync to restore the configuration of the chip on resume but (as Peter observed) does not actually define a register cache which means that the resume is never going to work and we trigger asserts in regmap. Fix this by enabling caching. Reported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reported-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
