B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3,  B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.

The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix divide by zero in mlx5, from Talut Batheesh.

 2) Guard against invalid GSO packets coming from untrusted guests and
    arriving in qdisc_pkt_len_init(), from Eric Dumazet.

 3) Similarly add such protection to the various protocol GSO handlers.
    From Willem de Bruijn.

 4) Fix regression added to IGMP source address checking for IGMPv3
    reports, from Felix Feitkau.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tls: Correct length of scatterlist in tls_sw_sendpage
  be2net: restore properly promisc mode after queues reconfiguration
  net: igmp: fix source address check for IGMPv3 reports
  gso: validate gso_type in GSO handlers
  net: qdisc_pkt_len_init() should be more robust
  ibmvnic: Allocate and request vpd in init_resources
  ibmvnic: Revert to previous mtu when unsupported value requested
  ibmvnic: Modify buffer size and number of queues on failover
  rds: tcp: compute m_ack_seq as offset from ->write_seq
  usbnet: silence an unnecessary warning
  cxgb4: fix endianness for vlan value in cxgb4_tc_flower
  cxgb4: set filter type to 1 for ETH_P_IPV6
  net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare

Commit 97a6ec4a ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.

A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.

Note that this issue doesn't affect net.git yet.

Fixes: 97a6ec4a ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointers txr and rxr are being initialized and a few statements later
are being assigned new values without the original values ever being
read. The initialized values are therefore redundant and can be
removed.

Cleans up clang warnings:
drivers/net/ethernet/broadcom/bnx2.c:5821:28: warning: Value stored to
'txr' during its initialization is never read
drivers/net/ethernet/broadcom/bnx2.c:5822:28: warning: Value stored to
'rxr' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since both first_rx_ctx and rx_skb are the head of rx ctx, it not
necessary to use two structure members to statically indicate
the head of rx ctx. So first_rx_ctx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Kernel doc fixes for networking

This patch series fixes kernel doc warnings found while running make htmldocs
pertaining to the networking subsystem. There is a finaly set of warnings due
to PHYLINK which I have not been able to resolve yet.

The last patch could thereoteically be applied to 'net' since the commit
referenced by the Fixes: tag is present in v4.15-rcX.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following warnings:
./net/core/dev.c:6438: warning: No description found for parameter 'extack'
./net/core/dev.c:6461: warning: No description found for parameter 'extack'

Fixes: 42ab19ee ("net: Add extack to upper device linking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the @dev comment, since we do not have a net_device argument, fixes the
following kernel doc warning: /net/core/dev.c:1707: warning: Excess function
parameter 'dev' description in 'call_netdevice_notifiers_info'
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We forgot to update the kernel doc header above sfp_register_upstream()

Fixes: c19bb000 ("sfp: convert to fwnode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the documentation warning:

include/linux/netdevice.h:1939: warning: Excess struct member 'carrier_changes' description in 'net_device'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: b2d3bcfa ("net: core: Expose number of link up/down transitions")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:50:34: warning:
 symbol 'hw_atl_boards' was not declared. Should it be static?

Fixes: 4948293f ("net: aquantia: Introduce new AQC devices and capabilities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return error code -ENOMEM from the aq_ndev_alloc() error
handling case instead of 0, as done elsewhere in this function.

Fixes: 23ee07ad ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return error code -EINVAL instead of 0 when num_vfs above
limit_vfs, as done elsewhere in this function.

Fixes: 0dc78621 ("nfp: handle SR-IOV already enabled when driver is probing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix bug that causes _absolute_ rtsym sizes of > 8 bytes (as per symbol
table) to result in incorrect space used during a TLV-based debug dump.

Detail: The size calculation stage calculates the correct size (size of
the rtsym address field == 8), while the dump uses the size in the table
to calculate the TLV size to reserve. Symbols with size <= 8 are handled
OK due to aligning sizes to 8, but including any absolute symbol with
listed size > 8 leads to an ENOSPC error during the dump.

Fixes: da762863 ("nfp: fix absolute rtsym handling in debug dump")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit bdcf0a42 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.

It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage.  The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.

We should sort only once, after filling in all the gids.

Fixes: bdcf0a42 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Similarly to tx ring, xdp_rxq_info is only registered
when !tfile->detached, so we need to avoid calling
xdp_rxq_info_unreg() twice too. The helper tun_cleanup_tx_ring()
already checks for this properly, so it is correct to put
xdp_rxq_info_unreg() just inside there.

Reported-by: syzbot+1c788d7ce0f0888f1d7f@syzkaller.appspotmail.com
Fixes: 8565d26b ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In orangefs_devreq_read, there is a loop which picks an op off the list
of pending ops.  If the loop fails to find an op, there is nothing to
read, and it returns EAGAIN.  If the op has been given up on, the loop
is restarted via a goto.  The bug is that the variable which the found
op is written to is not reinitialized, so if there are no more eligible
ops on the list, the code runs again on the already handled op.

This is triggered by interrupting a process while the op is being copied
to the client-core.  It's a fairly small window, but it's there.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

set_op_state_purged can delete the op.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Jakub Kicinski says:

====================
net: sched: add extack support for cls offloads

I've dropped the tests from the series because test_offloads.py changes
will conflict with bpf-next patches.  I will send four more patches with
tests once bpf-next is merged back, hopefully still making it into 4.16 :)

v4:
 - rebase on top of Alex's changes.

---

Quentin says:

This series tries to improve user experience when eBPF hardware offload
hits error paths at load time. In particular, it introduces netlink
extended ack support in the nfp driver.

To that aim, transmission of the pointer to the extack object is piped
through the `change()` operation of the existing classifiers (patch 1 to
6). Then it is used for TC offload in the nfp driver (patch 8) and in
netdevsim (patch 9, selftest in patch 10). Patch 7 adds a helper to handle
extack messages in the core when TC offload is disabled on the net device.

For completeness extack is propagated for classifiers other than cls_bpf,
but it's up to the drivers to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the recently added extack support for eBPF offload in the driver.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass a pointer to an extack object to nfp_app_xdp_offload() in order to
prepare for extack usage in the nfp driver. Next step will be to forward
this extack pointer to nfp_net_bpf_offload(), once this function is able
to use it for printing error messages.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a wrapper around tc_can_offload() that takes an additional
extack pointer argument in order to output an error message if TC
offload is disabled on the device.

In this way, the error message is handled by the core and can be the
same for all drivers.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack support for hardware offload of classifiers. In order
to achieve this, a pointer to a struct netlink_ext_ack is added to the
struct tc_cls_common_offload that is passed to the callback for setting
up the classifier. Function tc_cls_common_offload_init() is updated to
support initialization of this new attribute.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass the extack pointer obtained in the `->change()` filter operation to
cls_bpf_offload() and then to cls_bpf_offload_cmd(). This makes it
possible to use this extack pointer in drivers offloading BPF programs
in a future patch.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_u32. This makes it
possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_matchall. This makes
it possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_flower. This makes it
possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The scatterlist is reused by both sendmsg and sendfile.
If a sendmsg of smaller number of pages is followed by a sendfile
of larger number of pages, the scatterlist may be too short, resulting
in a crash in gcm_encrypt.

Add sg_unmark_end to make the list the correct length.

tls_sw_sendmsg already calls sg_unmark_end correctly when it allocates
memory in alloc_sg, or in zerocopy_from_iter.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we no longer localize channel/CPU affiliation within one NUMA
node, num_online_cpus() is used as the number of channel cap, instead of
the number of processors in a NUMA node.

This patch allows a bigger range for tuning the number of channels.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 62219066 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.

Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>

Fixes: 62219066 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spaces were mistakenly used instead of tabs in some of the code related
to reset functionality, which caused checkpatch.pl errors. These were
missed earlier so fixing them now.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).

This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.

Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes: a46182b0 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>

T3 devices have different ports on same PCI function,
so using dev_port to identify ports.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return statements in functions returning bool should use
true/false instead of 1/0.

This issue was detected with the help of Coccinelle.

Fixes: 85b35269 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Broadcom tags inserted by Broadcom switches put a 4 byte header after
the MAC SA and before the EtherType, which may look like some sort of 0
length LLC/SNAP packet (tcpdump and wireshark do think that way). With
ACS enabled in stmmac the packets were truncated to 8 bytes on
reception, whereas clearing this bit allowed normal reception to occur.

In order to make that possible, we need to pass a net_device argument to
the different core_init() functions and we are dependent on the Broadcom
tagger padding packets correctly (which it now does). To be as little
invasive as possible, this is only done for gmac1000 when the network
device is DSA-enabled (netdev_uses_dsa() returns true).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Peng Li says:

====================
add some features to hns3 driver

This patchset adds some features to hns3 driver, include the support
for ethtool command -d, -p and support for manager table.

[Patch 1/4] adds support for ethtool command -d, its ops is get_regs.
driver will send command to command queue, and get regs number and
regs value from command queue.
[Patch 2/4] adds manager table initialization for hardware.
[Patch 3/4] adds support for ethtool command -p. For fiber ports, driver
sends command to command queue, and IMP will write SGPIO regs to control
leds.
[Patch 4/4] adds support for net status led for fiber ports. Net status
include  port speed, total rx/tx packets and link status. Driver send
the status to command queue, and IMP will write SGPIO to control leds.

---
Change log:
V1 -> V2:
1, fix comments from Andrew Lunn, remove the patch "net: hns3: add
ethtool -p support for phy device".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Check the net status per second, include port speed, total rx/tx packets
and link status. Updating the led status for fiber port.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add led location support for fiber port. The led will keep blinking
when locating.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>