Add dependencies on PCI where necessary.

Fixes: 7e2bc7fb ("net: cavium: Drop dependency of NET_VENDOR_CAVIUM on PCI")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefan Wahren says:

====================
net: qca_spi: Minor bugfixes

This patch series contains some minor bugfixes for
the qca_spi driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In cases the probing fails the log level of the messages should
be an error.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e2 ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>

As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06e ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>

The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.

Thanks to David Lebrun for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.

Detected by CoverityScan, CID#1468411 ("Useless call")

Fixes: b5facfdb ("ipv6: sr: Compute flowlabel for outer IPv6 header of seg6 encap mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: dlebrun@google.com
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are some batman-adv fixes:

 - Fix gateway refcounting in BATMAN IV and V, by Sven Eckelmann (2 patches)

 - Fix debugfs paths when renaming interfaces, by Sven Eckelmann (2 patches)

 - Fix TT flag issues, by Linus Luessing (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

net/sched/cls_api.c:1101:43: warning: Using plain integer as NULL pointer
net/sched/cls_api.c:1492:75: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.

To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return

Fixes: d9fe64e5 ("net: asix: Add in_pm parameter")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

t.qset_idx can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c:2286 cxgb_extension_ioctl()
warn: potential spectre issue 'adapter->msix_info'

Fix this by sanitizing t.qset_idx before using it to index
adapter->msix_info

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rhashtable_init() currently does not take into account the user-passed
min_size parameter unless param->nelem_hint is set as well. As such,
the default size (number of buckets) will always be HASH_DEFAULT_SIZE
even if the smallest allowed size is larger than that. Remediate this
by unconditionally calling into rounded_hashtable_size() and handling
things accordingly.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: fixes 2018-07-18

here are small fixes for SMC: The first patch speeds up unidirectional
traffic, the second patch increases security, and the third patch
fixes a problem for fallback cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

During clc handshake the receive timeout is set to CLC_WAIT_TIME.
Remember and reset the original timeout value after the receive calls,
and remove a duplicate assignment of CLC_WAIT_TIME.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For security reasons the return code of get_user() should always be
checked.

Fixes: 01d2f7e2 ("net/smc: sockopts TCP_NODELAY and TCP_CORK")
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SMC protocol requires to send a separate consumer cursor update,
if it cannot be piggybacked to updates of the producer cursor.
Currently the decision to send a separate consumer cursor update
just considers the amount of data already received by the socket
program. It does not consider the amount of data already arrived, but
not yet consumed by the receiver. Basing the decision on the
difference between already confirmed and already arrived data
(instead of difference between already confirmed and already consumed
data), may lead to a somewhat earlier consumer cursor update send in
fast unidirectional traffic scenarios, and thus to better throughput.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Suggested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot is reporting stalls at nfc_llcp_send_ui_frame() [1]. This is
because nfc_llcp_send_ui_frame() is retrying the loop without any delay
when nonblocking nfc_alloc_send_skb() returned NULL.

Since there is no need to use MSG_DONTWAIT if we retry until
sock_alloc_send_pskb() succeeds, let's use blocking call.
Also, in case an unexpected error occurred, let's break the loop
if blocking nfc_alloc_send_skb() failed.

[1] https://syzkaller.appspot.com/bug?id=4a131cc571c3733e0eff6bc673f4e36ae48f19c6Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+d29d18215e477cfbfbdd@syzkaller.appspotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

My randconfig builds came across an old missing dependency for ILA:

ERROR: "dst_cache_set_ip6" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_get" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_init" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_destroy" [net/ipv6/ila/ila.ko] undefined!

We almost never run into this by accident because randconfig builds
end up selecting DST_CACHE from some other tunnel protocol, and this
one appears to be the only one missing the explicit 'select'.

>From all I can tell, this problem first appeared in linux-4.9
when dst_cache support got added to ILA.

Fixes: 79ff2fc3 ("ila: Cache a route to translated address")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver can spam the kernel log with multiple messages of:

    net eth0: eth0: allmulti set

Usually 4 or 8 at a time (probably because of using ConnMan).

This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.

According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."

OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.

The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMC ioctl processing requires the sock lock to work properly in
all thinkable scenarios.
Problem has been found with RaceFuzzer and fixes:
   KASAN: null-ptr-deref Read in smc_ioctl
Reported-by: Byoungyoung Lee <lifeasageek@gmail.com>
Reported-by: syzbot+35b2c5aa76fd398b9fd4@syzkaller.appspotmail.com
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Siva Reddy Kallam says:

====================
tg3: Update copyright and fix for tx timeout with 5762

First patch:
        Update copyright

Second patch:
        Add higher cpu clock for 5762
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered.  Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.

This patch was tested on Raspberry Pi 3B+

Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric reported that reverting the patch that fixed and simplified IPv6
multipath routes means reverting back to invalid userspace notifications.
eg.,
$ ip -6 route add 2001:db8:1::/64 nexthop dev eth0 nexthop dev eth1

only generates a single notification:
2001:db8:1::/64 dev eth0 metric 1024 pref medium

While working on a fix for this problem I found another case that is just
broken completely - a multipath route with a gateway followed by device
followed by gateway:
    $ ip -6 ro add 2001:db8:103::/64
          nexthop via 2001:db8:1::64
          nexthop dev dummy2
          nexthop via 2001:db8:3::64

In this case the device only route is dropped completely - no notification
to userpsace but no addition to the FIB either:

$ ip -6 ro ls
2001:db8:1::/64 dev dummy1 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy2 proto kernel metric 256 pref medium
2001:db8:3::/64 dev dummy3 proto kernel metric 256 pref medium
2001:db8:103::/64 metric 1024
	nexthop via 2001:db8:1::64 dev dummy1 weight 1
	nexthop via 2001:db8:3::64 dev dummy3 weight 1 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy2 proto kernel metric 256 pref medium
fe80::/64 dev dummy3 proto kernel metric 256 pref medium

Really, IPv6 multipath is just FUBAR'ed beyond repair when it comes to
device only routes, so do not allow it all.

This change will break any scripts relying on the mpath api for insert,
but I don't see any other way to handle the permutations. Besides, since
the routes are added to the FIB as standalone (non-multipath) routes the
kernel is not doing what the user requested, so it might as well tell the
user that.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct previous bad attempt at allowing sockets to come out of TCP
repair without sending window probes. To avoid changing size of
the repair variable in struct tcp_sock, this lets the decision for
sending probes or not to be made when coming out of repair by
introducing two ways to turn it off.

v2:
* Remove erroneous comment; defines now make behavior clear

Fixes: 70b7ff13 ("tcp: allow user to create repair socket without window probes")
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;

The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.

In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.

Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.

No additional cache line is required for the new condition.

Fixes: 34db548b ("mlx4: add page recycling in receive path")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Suggested-by: Martin KaFai Lau <kafai@fb.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

  CC [M]  drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
  clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
  ^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>

The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.

Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit adc176c5 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
added enhanced DAD with a nonce length of 6 bytes. However, RFC7527
doesn't specify the length of the nonce, other than being 6 + 8*k bytes,
with integer k >= 0 (RFC3971 5.3.2). The current implementation simply
assumes that the nonce will always be 6 bytes, but others systems are
free to choose different sizes.

If another system sends a nonce of different length but with the same 6
bytes prefix, it shouldn't be considered as the same nonce. Thus, check
that the length of the received nonce is the same as the length we sent.

Ugly scapy test script running on veth0:

def loop():
    pkt=sniff(iface="veth0", filter="icmp6", count=1)
    pkt = pkt[0]
    b = bytearray(pkt[Raw].load)
    b[1] += 1
    b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef'
    pkt[Raw].load = bytes(b)
    pkt[IPv6].plen += 8
    # fixup checksum after modifying the payload
    pkt[IPv6].payload.cksum -= 0x3b44
    if pkt[IPv6].payload.cksum < 0:
        pkt[IPv6].payload.cksum += 0xffff
    sendp(pkt, iface="veth0")

This should result in DAD failure for any address added to veth0's peer,
but is currently ignored.

Fixes: adc176c5 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch remove the following documentation warning
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:103: warning: Excess function parameter 'priv' description in 'stmmac_axi_setup'
It was introduced in commit afea0365 ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix a typo in the word Describe
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A KASAN:use-after-free bug was found related to ip6-erspan
while running selftests/net/ip6_gre_headroom.sh

It happens because of following sequence:
- ipv6hdr pointer is obtained from skb
- skb_cow_head() is called, skb->head memory is reallocated
- old data is accessed using ipv6hdr pointer

skb_cow_head() call was added in e41c7c68 ("ip6erspan: make sure
enough headroom at xmit."), but looking at the history there was a
chance of similar bug because gre_handle_offloads() and pskb_trim()
can also reallocate skb->head memory. Fixes tag points to commit
which introduced possibility of this bug.

This patch moves ipv6hdr pointer assignment after skb_cow_head() call.

Fixes: 5a963eb6 ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On XDP_TX we need to free up the frame only when tun_xdp_tx() returns a
negative value. A positive value indicates that the packet is
successfully enqueued to the ptr_ring, so freeing the page causes
use-after-free.

Fixes: 735fc405 ("xdp: change ndo_xdp_xmit API to support bulking")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a spelling typo in bonding.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the zerocopy sendmsg() path, there are error checks to revert
the zerocopy if we get any error code.  syzkaller has discovered
that tls_push_record can return -ECONNRESET, which is fatal, and
happens after the point at which it is safe to revert the iter,
as we've already passed the memory to do_tcp_sendpages.

Previously this code could return -ENOMEM and we would want to
revert the iter, but AFAIK this no longer returns ENOMEM after
a447da7d ("tls: fix waitall behavior in tls_sw_recvmsg"),
so we fail for all error codes.

Reported-by: syzbot+c226690f7b3126c5ee04@syzkaller.appspotmail.com
Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com
Signed-off-by: Dave Watson <davejwatson@fb.com>
Fixes: 3c4d7559 ("tls: kernel TLS support")
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Constantine Shulyupin <const@MakeLinux.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>