For proper operation of Armada 38x SDHCI controller proper 'clocks' property
is sufficient. Therefore it is not useful to keep an additional
'clock-frequency' property in SDHCI controller node of board-level Device Tree
file for Armada 385 DB.

This commit gets rid of useless 'clock-frequency' property.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-4-git-send-email-mw@semihalf.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

The Marvell Armada 38x SoC's SDHCI interface is capable of using 1.8v voltage,
needed for driving "UHS-I" SD cards at their full speed. It is not, however,
possible on the DB board. Due to physical connectivity connector supply is tied
to 3v and any attempt of changing voltage in order to operate in the fastest UHS
modes fails.

This patch enables equivalent SDHCI quirk in order to adjust controller
operation to system capabilities.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-3-git-send-email-mw@semihalf.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

The 370 rd has a 7 port, mv88E6182 switch, connected to eth1.  Add a
fixed-link subnode to the ethernet device tree node, to force
gigabit/full duplex.  Add a dsa node, with describing the four used
ports. This requires adding an alias to the mdio node, so it can be
referenced as a phandle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415214121-29286-3-git-send-email-andrew@lunn.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This commit modifies the Armada 370 and Armada 370 DB Device Tree
descriptions to use the simple-card DT binding to describe the audio
complex of the Armada 370 DB instead of a custom audio machine driver.

To do so, it:

 - Adds the sound-dai-cells properties to the CS42L51 node, the audio
   controller node and the SPDIF in/out nodes.

 - Completely changes the description of the sound complex to use the
   "simple-audio-card" DT binding instead of the
   "marvell,a370db-audio" DT binding.

 - Fixes the indentation to properly use tabs instead of spaces.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-6-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Back when audio was enabled, the muxing of some MPP pins was causing
problems. However, since commit fea038ed ("ARM: mvebu: Add proper
pin muxing on the Armada 370 DB board"), those problematic MPP pins
have been assigned a proper muxing for the Ethernet interfaces. This
proper muxing is now conflicting with the hog pins muxing that had
been added as part of 249f3822 ("ARM: mvebu: add audio support to
Armada 370 DB").

Therefore, this commit simply removes the hog pins muxing, which
solves a warning a boot time due to the conflicting muxing
requirements.

Fixes: fea038ed ("ARM: mvebu: Add proper pin muxing on the Armada 370 DB board")
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-5-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

There is only one 74hc595 connected to GPIO but two were given
in the registers-number property. Fix it up.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is an I2C eeprom connected on Lenovo ix4-300d, add the
corresponding node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Lenovo ix4-300d has two ethernet PHYs connected via RGMII. Add the
corresponding pinctrl settings.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is a GMII setting for GE0, add it to the common pinctrl node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Pinctrl settings for GE0 and GE1 are not only usable on RD-AXPWiFiAP.
Moreover, naming the RGMII settings pmx-ge{0,1} is not precise enough
as there is also a GMII setting for GE0.

Move the pinctrl sub-nodes to the common pinctrl node and rename them
to pmx-ge{0,1}-rgmii.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Armada XP pinctrl node gained an alias, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

In other MVEBU SoCs, the pin controller node is called pin-ctrl with
its base address added. Also, we have a node alias to access the pinctrl
node easily. Fix this for Armada XP pinctrl nodes to be consistent with
other SoCs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

All current Armada XP SoCs have their pin controller at 0x18000/0x38.
Move the common properties of pinctrl nodes to armada-xp.dtsi to allow
to share pinctrl settings later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The DIR665 has an 8 port Ethernet Switch, a Marvell mv88e6171. Add a
DSA node in DT, to instantiate DSA support for the 4 back panel ports,
the Internet port, and the port to the CPU which is connected to eth0.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-3-git-send-email-andrew@lunn.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Add a device tree description of the DLINK DIR665 wireless access
point. The support for the 88E6171 switch will be added in a later
patch.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-2-git-send-email-andrew@lunn.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

NETGEAR ReadyNAS 2120 supports its four main SATA disks via 2
Marvell 88SE9170 SATA controllers connected on the PCIe bus
of the the SoC. The two eSATA ports available at the rear of
the device are handled by the native SATA controller of the
Armada XP SoC powering the NAS. This patch enables the SoC
SATA controller in the .dts file to make those two rear ports
available.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/f3876c7a9ef11eb758b9df18c671ee740b8be614.1414250947.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Now that the timer and watchdog drivers support the Armada 375 usage of
the reference clock, we can enable it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1414248522-16055-5-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

On NETGEAR ReadyNAS 102, the two disks are connected to the external
Marvell 88SE9170 SATA Controller connected to the PCIe bus. The rear
eSATA port is connected to the native Armada 370 SATA controller.

This patch updates the comments in .dts file wrt SATA interfaces and
reduces the number of ports for native Armada 370 interface from 2
to 1.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/4af680f9a68281755e31df2491f0590046138230.1414185031.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

When writing initial .dts file for NETGEAR ReadyNAS 102, I put the wrong color
for backup and SATA leds (green instead of blue for all three).
Reported-by: Johan Kristell <johan.kristell@gmail.com>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/4eb4049d934a3a8fe9f7235dafb6842422792566.1414185031.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

The L2 cache controller on the Armada 370 and Armada XP SoCs is a
unified cache. Moreover, the Aurora cache controller is compatible
with the L2x0 cache controller: the "cache-unified" property is
required by its binding.

This patch fixes the Aurora L2 cache node for the Armada 370 and
Armada XP SoCs by adding this property.
Reported-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1412588276-4514-1-git-send-email-gregory.clement@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802

Pull audit updates from Eric Paris:
 "So this change across a whole bunch of arches really solves one basic
  problem.  We want to audit when seccomp is killing a process.  seccomp
  hooks in before the audit syscall entry code.  audit_syscall_entry
  took as an argument the arch of the given syscall.  Since the arch is
  part of what makes a syscall number meaningful it's an important part
  of the record, but it isn't available when seccomp shoots the
  syscall...

  For most arch's we have a better way to get the arch (syscall_get_arch)
  So the solution was two fold: Implement syscall_get_arch() everywhere
  there is audit which didn't have it.  Use syscall_get_arch() in the
  seccomp audit code.  Having syscall_get_arch() everywhere meant it was
  a useless flag on the stack and we could get rid of it for the typical
  syscall entry.

  The other changes inside the audit system aren't grand, fixed some
  records that had invalid spaces.  Better locking around the task comm
  field.  Removing some dead functions and structs.  Make some things
  static.  Really minor stuff"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: rename audit_log_remove_rule to disambiguate for trees
  audit: cull redundancy in audit_rule_change
  audit: WARN if audit_rule_change called illegally
  audit: put rule existence check in canonical order
  next: openrisc: Fix build
  audit: get comm using lock to avoid race in string printing
  audit: remove open_arg() function that is never used
  audit: correct AUDIT_GET_FEATURE return message type
  audit: set nlmsg_len for multicast messages.
  audit: use union for audit_field values since they are mutually exclusive
  audit: invalid op= values for rules
  audit: use atomic_t to simplify audit_serial()
  kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
  audit: reduce scope of audit_log_fcaps
  audit: reduce scope of audit_net_id
  audit: arm64: Remove the audit arch argument to audit_syscall_entry
  arm64: audit: Add audit hook in syscall_trace_enter/exit()
  audit: x86: drop arch from __audit_syscall_entry() interface
  sparc: implement is_32bit_task
  sparc: properly conditionalize use of TIF_32BIT
  ...

Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes

Merge "qcom DT changes for v3.18-3" from Kumar Gala:

Qualcomm ARM Based Device Tree Updates for v3.18-3

* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148

* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148

Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Pull more fixes from Kukjin Kim:

2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
  and exynos5420-arndale-octa boards, because the USB dwc3 controller
  will not work properly without dr_mode as host on above boards if
  the USB host and gadget are enabled in kernel configuration both.

* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ntb (non-transparent bridge) updates from Jon Mason:
 "Add support for Haswell NTB split BARs, a debugfs entry for basic
  debugging info, and some code clean-ups"

* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
  ntb: Adding split BAR support for Haswell platforms
  ntb: use errata flag set via DID to implement workaround
  ntb: conslidate reading of PPD to move platform detection earlier
  ntb: move platform detection to separate function
  NTB: debugfs device entry

Pull i2c updates from Wolfram Sang:
 "Highlights from the I2C subsystem for 3.18:

   - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.

   - designware driver gained AMD support, exynos gained exynos7 support

  The rest is usual driver stuff.  Hopefully no lowlights this time"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Add Device IDs for Intel Sunrise Point PCH
  i2c: hix5hd2: add i2c controller driver
  i2c-imx: Disable the clock on probe failure
  i2c: designware: Add support for AMD I2C controller
  i2c: designware: Rework probe() to get clock a bit later
  i2c: designware: Default to fast mode in case of ACPI
  i2c: axxia: Add I2C driver for AXM55xx
  i2c: exynos: add support for HSI2C module on Exynos7
  i2c: mxs: detect No Slave Ack on SELECT in PIO mode
  i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
  i2c: cros-ec-tunnel: Add of match table
  i2c: rcar: remove sign-compare flaw
  i2c: ismt: Use minimum descriptor size
  i2c: imx: Add arbitration lost check
  i2c: rk3x: Remove unlikely() annotations
  i2c: rcar: check for no IRQ in rcar_i2c_irq()
  i2c: rcar: make rcar_i2c_prepare_msg() *void*
  i2c: rcar: simplify check for last message
  i2c: designware: add support of platform data to set I2C mode
  i2c: designware: add support of I2C standard mode

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes after 3.18 merge.

  The urgent one is the fix for kernel panics with linked PCM substream
  triggered by the recent nonatomic PCM ops support.  Other two fixes
  (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
  a new Intel HD-audio controller"

* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
  ALSA: emu10k1: Fix deadlock in synth voice lookup
  ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
  ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88

Pull second round of input updates from Dmitry Torokhov:
 "Mostly simple bug fixes, although we do have one brand new driver for
  Microchip AR1021 i2c touchscreen.

  Also there is the change to stop trying to use i8042 active
  multiplexing by default (it is still possible to activate it via
  i8042.nomux=0 on boxes that implement it)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add Thrustmaster as Xbox 360 controller vendor
  Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
  Input: max77693-haptic - fix state check in imax77693_haptic_disable()
  Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
  Input: alps - fix v4 button press recognition
  Input: i8042 - disable active multiplexing by default
  Input: i8042 - add noloop quirk for Asus X750LN
  Input: synaptics - gate forcepad support by DMI check
  Input: Add Microchip AR1021 i2c touchscreen
  Input: cros_ec_keyb - add of match table
  Input: serio - avoid negative serio device numbers
  Input: avoid negative input device numbers
  Input: automatically set EV_ABS bit in input_set_abs_params
  Input: adp5588-keys - cancel workqueue in failure path
  Input: opencores-kbd - switch to using managed resources
  Input: evdev - fix EVIOCG{type} ioctl

Pull infiniband/RDMA updates from Roland Dreier:
 - large set of iSER initiator improvements
 - hardware driver fixes for cxgb4, mlx5 and ocrdma
 - small fixes to core midlayer

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
  RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
  RDMA/cxgb4: Add missing neigh_release in find_route
  RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
  RDMA/cxgb4: Make c4iw_wr_log_size_order static
  IB/core: Fix XRC race condition in ib_uverbs_open_qp
  IB/core: Clear AH attr variable to prevent garbage data
  RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
  RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
  RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
  RDMA/ocrdma: Remove a unused-label warning
  RDMA/ocrdma: Convert kernel VA to PA for mmap in user
  RDMA/ocrdma: Get vlan tag from ib_qp_attrs
  RDMA/ocrdma: Add default GID at index 0
  IB/mlx5, iser, isert: Add Signature API additions
  Target/iser: Centralize ib_sig_domain setting
  IB/iser: Centralize ib_sig_domain settings
  IB/mlx5: Use extended internal signature layout
  IB/iser: Set IP_CSUM as default guard type
  IB/iser: Remove redundant assignment
  IB/mlx5: Use enumerations for PI copy mask
  ...

Pull more perf updates from Ingo Molnar:
 "A second (and last) round of late coming fixes and changes, almost all
  of them in perf tooling:

  User visible tooling changes:

   - Add period data column and make it default in 'perf script' (Jiri
     Olsa)

   - Add a visual cue for toggle zeroing of samples in 'perf top'
     (Taeung Song)

   - Improve callchains when using libunwind (Namhyung Kim)

  Tooling fixes and infrastructure changes:

   - Fix for double free in 'perf stat' when using some specific invalid
     command line combo (Yasser Shalabi)

   - Fix off-by-one bugs in map->end handling (Stephane Eranian)

   - Fix off-by-one bug in maps__find(), also related to map->end
     handling (Namhyung Kim)

   - Make struct symbol->end be the first addr after the symbol range,
     to make it match the convention used for struct map->end.  (Arnaldo
     Carvalho de Melo)

   - Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
     live' (Jiri Olsa)

   - Fix python test build by moving callchain_param to an object linked
     into the python binding (Jiri Olsa)

   - Document sysfs events/ interfaces (Cody P Schafer)

   - Fix typos in perf/Documentation (Masanari Iida)

   - Add missing 'struct option' forward declaration (Arnaldo Carvalho
     de Melo)

   - Add option to copy events when queuing for sorting across cpu
     buffers and enable it for 'perf kvm stat live', to avoid having
     events left in the queue pointing to the ring buffer be rewritten
     in high volume sessions.  (Alexander Yarygin, improving work done
     by David Ahern):

   - Do not include a struct hists per perf_evsel, untangling the
     histogram code from perf_evsel, to pave the way for exporting a
     minimalistic tools/lib/api/perf/ library usable by tools/perf and
     initially by the rasd daemon being developed by Borislav Petkov,
     Robert Richter and Jean Pihet.  (Arnaldo Carvalho de Melo)

   - Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
     thread maps mean syswide monitoring, reducing the boilerplate for
     tools that only want system wide mode.  (Arnaldo Carvalho de Melo)

   - Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
     should be just a front end for exit + free (Arnaldo Carvalho de
     Melo)

   - Add support to new style format of kernel PMU event.  (Kan Liang)

  and other misc fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
  perf script: Add period as a default output column
  perf script: Add period data column
  perf evsel: No need to drag util/cgroup.h
  perf evlist: Add missing 'struct option' forward declaration
  perf evsel: Move exit stuff from __delete to __exit
  kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
  perf kvm stat live: Enable events copying
  perf session: Add option to copy events when queueing
  perf Documentation: Fix typos in perf/Documentation
  perf trace: Use thread_{,_set}_priv helpers
  perf kvm: Use thread_{,_set}_priv helpers
  perf callchain: Create an address space per thread
  perf report: Set callchain_param.record_mode for future use
  perf evlist: Fix for double free in tools/perf stat
  perf test: Add test case for pmu event new style format
  perf tools: Add support to new style format of kernel PMU event
  perf tools: Parse the pmu event prefix and suffix
  Revert "perf tools: Default to cpu// for events v5"
  perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
  perf Documentation: sysfs events/ interfaces
  ...

Pull sparc fixes from David Miller:
 "Here we have two bug fixes:

  1) The current thread's fault_code is not setup properly upon entry to
     do_sparc64_fault() in some paths, leading to spurious SIGBUS.

  2) Don't use a zero length array at the end of thread_info on sparc64,
     otherwise end_of_stack() isn't right"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Do not define thread fpregs save area as zero-length array.
  sparc64: Fix corrupted thread fault code.

Pull networking fixes from David Miller:
 "A quick batch of bug fixes:

  1) Fix build with IPV6 disabled, from Eric Dumazet.

  2) Several more cases of caching SKB data pointers across calls to
     pskb_may_pull(), thus referencing potentially free'd memory.  From
     Li RongQing.

  3) DSA phy code tests operation presence improperly, instead of going:

        if (x->ops->foo)
                r = x->ops->foo(args);

     it was going:

        if (x->ops->foo(args))
                r = x->ops->foo(args);

   Fix from Andew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  Net: DSA: Fix checking for get_phy_flags function
  ipv6: fix a potential use after free in sit.c
  ipv6: fix a potential use after free in ip6_offload.c
  ipv4: fix a potential use after free in gre_offload.c
  tcp: fix build error if IPv6 is not enabled

The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This breaks the stack end corruption detection facility.

What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.

"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.

So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.

Fix this by making the size explicit.

Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves.  So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.

Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:

1) For pre-hypervisor TLB protection violation traps, if we took
   the 'winfix_trampoline' path we wouldn't have %g4 initialized
   with the FAULT_CODE_* value yet.  Resulting in using the
   TLB_TAG_ACCESS register address value instead.

2) In the TSB miss path, when we notice that we are going to use a
   hugepage mapping, but we haven't allocated the hugepage TSB yet, we
   still have to take the window fixup case into consideration and
   in that particular path we leave %g4 not setup properly.

Errors on this sort were largely invisible previously, but after
commit 4ccb9272 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.

FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.

Fixes: 4ccb9272 ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull slave-dmaengine updates from Vinod Koul:
 "For dmaengine contributions we have:
   - designware cleanup by Andy
   - my series moving device_control users to dmanegine_xxx APIs for
     later removal of device_control API
   - minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
     etc"

* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
  serial: atmel: add missing dmaengine header
  dmaengine: remove FSLDMA_EXTERNAL_START
  dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
  carma-fpga: move to fsl_dma_external_start()
  carma-fpga: use dmaengine_xxx() API
  dmaengine: freescale: add and export fsl_dma_external_start()
  dmaengine: add dmaengine_prep_dma_sg() helper
  video: mx3fb: use dmaengine_terminate_all() API
  serial: sh-sci: use dmaengine_terminate_all() API
  net: ks8842: use dmaengine_terminate_all() API
  mtd: sh_flctl: use dmaengine_terminate_all() API
  mtd: fsmc_nand: use dmaengine_terminate_all() API
  V4L2: mx3_camer: use dmaengine_pause() API
  dmaengine: coh901318: use dmaengine_terminate_all() API
  pata_arasan_cf: use dmaengine_terminate_all() API
  dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
  dmaengine: dw: export probe()/remove() and Co to users
  dmaengine: dw: enable and disable controller when needed
  dmaengine: dw: always export dw_dma_{en,dis}able
  dmaengine: dw: introduce dw_dma_on() helper
  ...

Pull fbdev updates from Tomi Valkeinen:
 - new 6x10 font
 - various small fixes and cleanups

* tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (30 commits)
  fonts: Add 6x10 font
  videomode: provide dummy inline functions for !CONFIG_OF
  video/atmel_lcdfb: Introduce regulator support
  fbdev: sh_mobile_hdmi: Re-init regs before irq re-enable on resume
  framebuffer: fix screen corruption when copying
  framebuffer: fix border color
  arm, fbdev, omap2, LLVMLinux: Remove nested function from omapfb
  arm, fbdev, omap2, LLVMLinux: Remove nested function from omap2 dss
  video: fbdev: valkyriefb.c: use container_of to resolve fb_info_valkyrie from fb_info
  video: fbdev: pxafb.c: use container_of to resolve pxafb_info/layer from fb_info
  video: fbdev: cyber2000fb.c: use container_of to resolve cfb_info from fb_info
  video: fbdev: controlfb.c: use container_of to resolve fb_info_control from fb_info
  video: fbdev: sa1100fb.c: use container_of to resolve sa1100fb_info from fb_info
  video: fbdev: stifb.c: use container_of to resolve stifb_info from fb_info
  video: fbdev: sis: sis_main.c: Cleaning up missing null-terminate in conjunction with strncpy
  video: valkyriefb: Fix unused variable warning in set_valkyrie_clock()
  video: fbdev: use %*ph specifier to dump small buffers
  video: mx3fb: always enable BACKLIGHT_LCD_SUPPORT
  video: fbdev: au1200fb: delete double assignment
  video: fbdev: sis: delete double assignment
  ...

Pull second batch of changes for KVM/{arm,arm64} from Marc Zyngier:
 "The most obvious thing is the sizeable MMU changes to support 48bit
  VAs on arm64.

  Summary:

   - support for 48bit IPA and VA (EL2)
   - a number of fixes for devices mapped into guests
   - yet another VGIC fix for BE
   - a fix for CPU hotplug
   - a few compile fixes (disabled VGIC, strict mm checks)"

[ I'm pulling directly from Marc at the request of Paolo Bonzini, whose
  backpack was stolen at Düsseldorf airport and will do new keys and
  rebuild his web of trust.    - Linus ]

* tag 'kvm-arm-for-3.18-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm:
  arm/arm64: KVM: Fix BE accesses to GICv2 EISR and ELRSR regs
  arm: kvm: STRICT_MM_TYPECHECKS fix for user_mem_abort
  arm/arm64: KVM: Ensure memslots are within KVM_PHYS_SIZE
  arm64: KVM: Implement 48 VA support for KVM EL2 and Stage-2
  arm/arm64: KVM: map MMIO regions at creation time
  arm64: kvm: define PAGE_S2_DEVICE as read-only by default
  ARM: kvm: define PAGE_S2_DEVICE as read-only by default
  arm/arm64: KVM: add 'writable' parameter to kvm_phys_addr_ioremap
  arm/arm64: KVM: fix potential NULL dereference in user_mem_abort()
  arm/arm64: KVM: use __GFP_ZERO not memset() to get zeroed pages
  ARM: KVM: fix vgic-disabled build
  arm: kvm: fix CPU hotplug