[Why]
DC is very fast at link training and stream enablement
which causes issues such as blackscreens for non-compliant
monitors.

[How]
After debugging with scaler vendors we implement the
minimum delays at the necessary locations to ensure
the monitor does not hang.  Delays are generic due to
lack of IEEE OUI information on the failing displays.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
DMUB command table should be allowed to be used
only if dmcu is explicitly disabled.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

To allow code reuse with minimal duplication watermark
calculation needs to be function pointer.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

During the debugging process related to a hot-plug
problem with 4k display, we realized that we had
some issues related to the global state validation.
This problem was not explicitly highlighted in the
dmesg log, for this reason, this commit adds a function
that converts `enum dc_status` to a human-readable
string and appends the proper warning message in case
of failure.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Dummy pstate latency actually varies between different
UCLK frequencies, when calculating watermark C, if DAL
always assumes worst case, then it can lead to dummy
pstate not supported scenarios.

[how]
Rather than statically calculating dummy pstate using
worst case, we store the entire table of UCLK to dummy
pstate relationships.  On a per mode basis, we calculate
the actual UCLK lower limit, and use the dynamic worst
case dummy pstate latency.  This prevents the situation
where we don't support full p-state (which will force
high DPM), but still use low DPM dummy pstate latency.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
The change causes some regression in a common use case.
Will need more investigation before fixing the original issue.

[how]
This reverts commit fb8cf277.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We were updating mpcc if there were tree changes which
is unnecessary since any mpcc being added or removed
will automatically update the tree.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
Add emul specific hw function to dmub, in case of
emulator is created, we can runtime switch between
dmub emulator or dmub uC via is_virtual flag in dmub.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The SDP deadline indicate the vertical time to send CRC
infopacket in PSR.
Signed-off-by: po-tchen <po-ting.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some sprcified monitor scalar cannot recognize timing
change on demand. Once the link phy disable and enable
during a short period then the Sink protection mechanism
could keep the screen in blank and cannot be recoverred.

[How]
To add 100ms delay between enable link phy and link training.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Header Changes]
       - Add SDP transmission deadline for PSR config cmd
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
for audio on real TV issue.

[how]
-add wall clock programming for DPREF based when
Pixel clock is done by DP DTO.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DML failures occur for 420 modes with dynamic pipe
splitting enabled because the ChromaViewport exceeds
the ChromaSurfaceWidth.

This is caused by adding the viewport_width instead
of the viewport_width_c.

This similarly occurs for rotated modes due to the
use of viewport_height instead of viewport_height_c.

[How]
Correct the calculations.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commmit fd0293dd.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
SOC_BOUNDING_BOX_VALID is unused and not required for dcn21.

[How]
Remove it.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DSC calculations fail because the u16 bits_per_pixel from
the DRM struct is being casted to the u8 drm_bpp parameters
and locals. Integer wraparound is happening because this
value is greater than 255.

[How]
Use u16 to match what's in the structure instead of u8.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Disabling DPG should happen after setting watermarks and clocks
Signed-off-by: Wesley Chalmers <wchalmer@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Header Changes]
       - Version bump to 1.0.13
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Typos cause bandwidth calculation errors, one
of which can cause infinite loop on dcn1 with eDP
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When we want to use float point operation on Linux
we need to use within special kernel protection
(`kernel_fpu_{begin,end}()`.), otherwise the kernel
can clobber userspace FPU register state. For detecting
these issues we use a tool named objtool (with -Ffa
flags) to highlight the FPU problems, all warnings can
be summed up as follows:

./tools/objtool/objtool check -Ffa
drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.o

[..] dc/dsc/rc_calc.o: warning: objtool: get_qp_set()+0x2f8:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: dsc_roundf()+0x5:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: dsc_ceil()+0x5:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: get_ofs_set()+0x3eb:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: calc_rc_params()+0x3c:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/dc_dsc.o: warning: objtool:
get_dsc_bandwidth_range.isra.0()+0x8d:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/dc_dsc.o: warning: objtool: setup_dsc_config()+0x2ef:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc_dpi.o: warning: objtool:copy_pps_fields()+0xbb:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc_dpi.o: warning: objtool:
dscc_compute_dsc_parameters()+0x7b:
FPU instruction outside of kernel_fpu_{begin,end}()

This commit fixes the above issues by rework DSC as described:

1. Isolate all FPU operations in a single file;
2. Use FPU flags only in the file that handles FPU operations;
3. Isolate all functions that require float point operation in static
   functions;
4. Add a mid-layer function that does not use any float point operation,
   and that could be safely invoked in other parts of the code.
5. Keep float point operation under DC_FP_{START/END} macro.

CC: Christian König <christian.koenig@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Tony Cheng <tony.cheng@amd.com>
CC: Harry Wentland <hwentlan@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
for following new format, no alpha
       SURFACE_PIXEL_FORMAT_GRPH_RGB111110_FLOAT/_FIX:
       SURFACE_PIXEL_FORMAT_GRPH_BGR101111_FLOAT/_FIX
       same as case SURFACE_PIXEL_FORMAT_GRPH_ARGB1555:
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Even though they are technically MMIO registers I put the bits with the sqind block
for organizational purposes.

Requested for UMR debugging.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix race condition issue when multiple jpeg starts are called.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As will clear vf fw during unload driver, to avoid idle fail. Need
to clear KIQ portion also.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Ack-by: Monk.liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Ack-by: Monk.liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Guest VM issue the PSP clear_vf_fw command at 2 points:
1.On VF driver loading, after VF message PSP to setup rings,
the next command is “clear_vf_fw”
2.On VF driver unload before VF message to
destroy rings
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Ack-by: Monk.liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes: c1cf79ca ("drm/amdgpu: use IP discovery table for renoir")

This nullptr issue should be specific on the Renoir series during try access the PWR_MISC_CNTL_STATUS
when PWR IP not been detected by discovery table. Moreover the PWR IP not existing in Renoir series is
expected therefore just avoid access PWR register in Renoir series.
Signed-off-by: Prike.Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Initializes Powertune data for a specific Hawaii card by fixing what
looks like a typo in the code. The device ID 66B1 is not a supported
device ID for this driver, and is not mentioned elsewhere. 67B1 is a
valid device ID, and is a Hawaii Pro GPU.

I have tested on my R9 390 which has device ID 67B1, and it works
fine without problems.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The comments say that the serial number is a 16-digit HEX string so the
buffer needs to be at least 17 characters to hold the NUL terminator.

The other issue is that "size" returned from sprintf() is the number of
characters before the NUL terminator so the memcpy() wasn't copying the
terminator.  The serial number needs to be NUL terminated so that it
doesn't lead to a read overflow in amdgpu_device_get_serial_number().
Also it's just cleaner and faster to sprintf() directly to adev->serial[]
instead of using a temporary buffer.

Fixes: 81a16241 ("drm/amdgpu: Add unique_id and serial_number for Arcturus v3")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>

Move the common code to amdgpu_smu.c instead of having one
copy in both smu_v11_0.c and smu_v12_0.c.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update the calling chain from "amdgpu_smu.c -> ${asic}_ppt.c ->
smu_v11/12_0.c -> amdgpu_smu.c (smu_common_read_sensor())" to "
"amdgpu_smu.c -> ${asic}_ppt.c -> smu_v11/12_0.c". This can help
to maintain clear code layers. More similar changes will be coming.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Since SMU_MSG_GetDpmClockFreq is known to be supported for Vega20
and before ASICs only. For those ASICs supporting swSMU, it is not
supported.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Since .populate_smc_tables is just a wrapper of .set_default_dpm_table.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It has exactly the same functionality as .set_deep_sleep_dcefclk.

V2: correct the macro name for better trace
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Silence documentation warnings by correcting kernel-doc comments.

./drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:3388: warning: Excess function parameter 'suspend' description in 'amdgpu_device_suspend'
./drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:3485: warning: Excess function parameter 'resume' description in 'amdgpu_device_resume'
./drivers/gpu/drm/amd/amdgpu/amdgpu_vram_mgr.c:418: warning: Excess function parameter 'tbo' description in 'amdgpu_vram_mgr_del'
./drivers/gpu/drm/amd/amdgpu/amdgpu_vram_mgr.c:418: warning: Excess function parameter 'place' description in 'amdgpu_vram_mgr_del'
./drivers/gpu/drm/amd/amdgpu/amdgpu_gtt_mgr.c:279: warning: Excess function parameter 'tbo' description in 'amdgpu_gtt_mgr_del'
./drivers/gpu/drm/amd/amdgpu/amdgpu_gtt_mgr.c:279: warning: Excess function parameter 'place' description in 'amdgpu_gtt_mgr_del'
./drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:332: warning: Function parameter or member 'hdcp_workqueue' not described in 'amdgpu_display_manager'
./drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:332: warning: Function parameter or member 'cached_dc_state' not described in 'amdgpu_display_manager'
Signed-off-by: Colton Lewis <colton.w.lewis@protonmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Requested for UMR support.

(v2): Also add reg/bits for gfx9 headers
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

if guest driver failed to enter full GPU access, amdgpu_driver_load_kms
will unload kms and free dev->dev_private, drm_dev_register would access
null pointer. Driver will enter an error state and can't be unloaded.
Signed-off-by: Liu ChengZhe <ChengZhe.Liu@amd.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Since DAL settings come between .hw_init and .late_init of SMU. And
DAL needs to know the maximum sustainable clocks.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-and-Tested-by: Flora Cui <flora.cui@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Before counting the OD percent into max power limit margin.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>