- 10 Sep, 2018 20 commits
-
-
Mathias Nyman authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit 229bc19f upstream. Don't rely on event interrupt (EINT) bit alone to detect pending port change in resume. If no change event is detected the host may be suspended again, oterwise roothubs are resumed. There is a lag in xHC setting EINT. If we don't notice the pending change in resume, and the controller is runtime suspeded again, it causes the event handler to assume host is dead as it will fail to read xHC registers once PCI puts the controller to D3 state. [ 268.520969] xhci_hcd: xhci_resume: starting port polling. [ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling. [ 268.521030] xhci_hcd: xhci_suspend: stopping port polling. [ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001 [ 268.521139] xhci_hcd: Port Status Change Event for port 3 [ 268.521149] xhci_hcd: resume root hub [ 268.521163] xhci_hcd: port resume event for port 3 [ 268.521168] xhci_hcd: xHC is not running. [ 268.521174] xhci_hcd: handle_port_status: starting port polling. [ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead The EINT lag is described in a additional note in xhci specs 4.19.2: "Due to internal xHC scheduling and system delays, there will be a lag between a change bit being set and the Port Status Change Event that it generated being written to the Event Ring. If SW reads the PORTSC and sees a change bit set, there is no guarantee that the corresponding Port Status Change Event has already been written into the Event Ring." Cc: <stable@vger.kernel.org> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com>
-
Stefano Brivio authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit e78bfb07 ] Commit 8b700862 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") introduced a different handling for the pfmemalloc flag in copy and clone paths. In __skb_clone(), now, the flag is set only if it was set in the original skb, but not cleared if it wasn't. This is wrong and might lead to socket buffers being flagged with pfmemalloc even if the skb data wasn't allocated from pfmemalloc reserves. Copy the flag instead of ORing it. Reported-by:
Sabrina Dubroca <sd@queasysnail.net> Fixes: 8b700862 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Tested-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Stefano Brivio authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit 8b700862 ] The pfmemalloc flag indicates that the skb was allocated from the PFMEMALLOC reserves, and the flag is currently copied on skb copy and clone. However, an skb copied from an skb flagged with pfmemalloc wasn't necessarily allocated from PFMEMALLOC reserves, and on the other hand an skb allocated that way might be copied from an skb that wasn't. So we should not copy the flag on skb copy, and rather decide whether to allow an skb to be associated with sockets unrelated to page reclaim depending only on how it was allocated. Move the pfmemalloc flag before headers_start[0] using an existing 1-bit hole, so that __copy_skb_header() doesn't copy it. When cloning, we'll now take care of this flag explicitly, contravening to the warning comment of __skb_clone(). While at it, restore the newline usage introduced by commit b1937227 ("net: reorganize sk_buff for faster __copy_skb_header()") to visually separate bytes used in bitfields after headers_start[0], that was gone after commit a9e419dc ("netfilter: merge ctinfo into nfct pointer storage area"), and describe the pfmemalloc flag in the kernel-doc structure comment. This doesn't change the size of sk_buff or cacheline boundaries, but consolidates the 15 bits hole before tc_index into a 2 bytes hole before csum, that could now be filled more easily. Reported-by:
Patrick Talbert <ptalbert@redhat.com> Fixes: c93bdd0e ("netvm: allow skb allocation to use PFMEMALLOC reserves") Signed-off-by:
-
Sanjeev Bansal authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit 3a498606 ] This patch has fix for TX timeout while running bi-directional traffic with 100 Mbps using 5762. Signed-off-by:
Sanjeev Bansal <sanjeevb.bansal@broadcom.com> Signed-off-by:
Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Gustavo A. R. Silva authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit 9ba8376c ] It seems that a *break* is missing in order to avoid falling through to the default case. Otherwise, checking *chan* makes no sense. Fixes: 72df7a72 ("ptp: Allow reassigning calibration pin function") Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit df8ed346 ] Currently also the pause flags are removed from phydev->supported because they're not included in PHY_DEFAULT_FEATURES. I don't think this is intended, especially when considering that this function can be called via phy_set_max_speed() anywhere in a driver. Change the masking to mask out only the values we're going to change. In addition remove the misleading comment, job of this small function is just to adjust the supported and advertised speeds. Fixes: f3a6bd39 ("phylib: Add phy_set_max_speed helper") Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
David Ahern authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit e7372197 ] Xin reported that icmp replies may not use the address on the device the echo request is received if the destination address is broadcast. Instead a route lookup is done without considering VRF context. Fix by setting oif in flow struct to the master device if it is enslaved. That directs the lookup to the VRF table. If the device is not enslaved, oif is still 0 so no affect. Fixes: cd2fbe1b ("net: Use VRF device index for lookups on RX") Reported-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Davidlohr Bueso authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit 107d01f5 ] rhashtable_init() currently does not take into account the user-passed min_size parameter unless param->nelem_hint is set as well. As such, the default size (number of buckets) will always be HASH_DEFAULT_SIZE even if the smallest allowed size is larger than that. Remediate this by unconditionally calling into rounded_hashtable_size() and handling things accordingly. Signed-off-by:
Davidlohr Bueso <dbueso@suse.de> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Colin Ian King authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit 169dc027 ] The rol32 call is currently rotating hash but the rol'd value is being discarded. I believe the current code is incorrect and hash should be assigned the rotated value returned from rol32. Thanks to David Lebrun for spotting this. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Tyler Hicks authored
BugLink: https://bugs.launchpad.net/bugs/1791080 [ Upstream commit 70ba5b6d ] The low and high values of the net.ipv4.ping_group_range sysctl were being silently forced to the default disabled state when a write to the sysctl contained GIDs that didn't map to the associated user namespace. Confusingly, the sysctl's write operation would return success and then a subsequent read of the sysctl would indicate that the low and high values are the overflowgid. This patch changes the behavior by clearly returning an error when the sysctl write operation receives a GID range that doesn't map to the associated user namespace. In such a situation, the previous value of the sysctl is preserved and that range will be returned in a subsequent read of the sysctl. Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Jing Xia authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit 9f15bde6 upstream. It was reported that a kernel crash happened in mem_cgroup_iter(), which can be triggered if the legacy cgroup-v1 non-hierarchical mode is used. Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b8f ...... Call trace: mem_cgroup_iter+0x2e0/0x6d4 shrink_zone+0x8c/0x324 balance_pgdat+0x450/0x640 kswapd+0x130/0x4b8 kthread+0xe8/0xfc ret_from_fork+0x10/0x20 mem_cgroup_iter(): ...... if (css_tryget(css)) <-- crash here break; ...... The crashing reason is that mem_cgroup_iter() uses the memcg object whose pointer is stored in iter->position, which has been freed before and filled with POISON_FREE(0x6b). And the root cause of the use-after-free issue is that invalidate_reclaim_iterators() fails to reset the value of iter->position to NULL when the css of the memcg is released in non- hierarchical mode. Link: http://lkml.kernel.org/r/1531994807-25639-1-git-send-email-jing.xia@unisoc.com Fixes: 6df38689 ("mm: memcontrol: fix possible memcg leak due to interrupted reclaim") Signed-off-by:
Jing Xia <jing.xia.mail@gmail.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <chunyan.zhang@unisoc.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Vineet Gupta authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit 93312b6d upstream. mprotect(EXEC) was failing for stack mappings as default vm flags was missing MAYEXEC. This was triggered by glibc test suite nptl/tst-execstack testcase What is surprising is that despite running LTP for years on, we didn't catch this issue as it lacks a directed test case. gcc dejagnu tests with nested functions also requiring exec stack work fine though because they rely on the GNU_STACK segment spit out by compiler and handled in kernel elf loader. This glibc case is different as the stack is non exec to begin with and a dlopen of shared lib with GNU_STACK segment triggers the exec stack proceedings using a mprotect(PROT_EXEC) which was broken. CC: stable@vger.kernel.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Alexey Brodkin authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit 6e376114 upstream. swap was broken on ARC due to silly copy-paste issue. We encode offset from swapcache page in __swp_entry() as (off << 13) but were not decoding back in __swp_offset() as (off >> 13) - it was still (off << 13). This finally fixes swap usage on ARC. | # mkswap /dev/sda2 | | # swapon -a -e /dev/sda2 | Adding 500728k swap on /dev/sda2. Priority:-2 extents:1 across:500728k | | # free | total used free shared buffers cached | Mem: 765104 13456 751648 4736 8 4736 | -/+ buffers/cache: 8712 756392 | Swap: 500728 0 500728 Cc: stable@vger.kernel.org Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
-
Takashi Iwai authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit 39675f7a upstream. The SNDRV_RAWMIDI_IOCTL_PARAMS ioctl may resize the buffers and the current code is racy. For example, the sequencer client may write to buffer while it being resized. As a simple workaround, let's switch to the resized buffer inside the stream runtime lock. Reported-by: syzbot+52f83f0ea8df16932f7f@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
OGAWA Hirofumi authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit 35033ab9 upstream. In parse_options(), if match_strdup() failed, parse_options() leaves opts->iocharset in unexpected state (i.e. still pointing the freed string). And this can be the cause of double free. To fix, this initialize opts->iocharset always when freeing. Link: http://lkml.kernel.org/r/8736wp9dzc.fsf@mail.parknet.co.jpSigned-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reported-by: syzbot+90b8e10515ae88228a92@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dewet Thibaut authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit fbdb328c upstream. commit b3b7c479 ("x86/MCE: Serialize sysfs changes") introduced a min interval limitation when setting the check interval for polled MCEs. However, the logic is that 0 disables polling for corrected MCEs, see Documentation/x86/x86_64/machinecheck. The limitation prevents disabling. Remove this limitation and allow the value 0 to disable polling again. Fixes: b3b7c479 ("x86/MCE: Serialize sysfs changes") Signed-off-by:
Dewet Thibaut <thibaut.dewet@nokia.com> Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> [ Massage commit message. ] Signed-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20180716084927.24869-1-alexander.sverdlin@nokia.comSigned-off-by:
-
Lan Tianyu authored
BugLink: https://bugs.launchpad.net/bugs/1791080 commit b5020a8e upstream. Syzbot reports crashes in kvm_irqfd_assign(), caused by use-after-free when kvm_irqfd_assign() and kvm_irqfd_deassign() run in parallel for one specific eventfd. When the assign path hasn't finished but irqfd has been added to kvm->irqfds.items list, another thead may deassign the eventfd and free struct kvm_kernel_irqfd(). The assign path then uses the struct kvm_kernel_irqfd that has been freed by deassign path. To avoid such issue, keep irqfd under kvm->irq_srcu protection after the irqfd has been added to kvm->irqfds.items list, and call synchronize_srcu() in irq_shutdown() to make sure that irqfd has been fully initialized in the assign path. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Tianyu Lan <tianyu.lan@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Martin Schwidefsky authored
CVE-2017-5715 (Spectre v2 s390x) git commit e1cf4bef "bpf, s390x: remove ld_abs/ld_ind" removed the code that generated the indirect branch "basr %b5,%w1" from the BPF JIT. Older versions of the BPF which still have support for LD_ABS/LD_IND need a patch to add the execute trampoline for this branch instruction. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Martin Schwidefsky authored
CVE-2017-5715 (Spectre v2 s390x) The memove, memset, memcpy, __memset16, __memset32 and __memset64 function have an additional indirect return branch in form of a "bzr" instruction. These need to use expolines as well. Fixes: 97489e06 ("s390/lib: use expoline for indirect branches") Signed-off-by:
-
Martin Schwidefsky authored
CVE-2017-5715 (Spectre v2 s390x) Detect and report the etoken facility. With spectre_v2=auto or CONFIG_EXPOLINE_AUTO=y automatically disable expolines and use the full branch prediction mode for the kernel. Signed-off-by:
-
- 06 Sep, 2018 20 commits
-
-
Greg Kroah-Hartman authored
BugLink: https://bugs.launchpad.net/bugs/1790884Signed-off-by:
-
Tetsuo Handa authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit 3bc53be9 upstream. syzbot is reporting stalls at nfc_llcp_send_ui_frame() [1]. This is because nfc_llcp_send_ui_frame() is retrying the loop without any delay when nonblocking nfc_alloc_send_skb() returned NULL. Since there is no need to use MSG_DONTWAIT if we retry until sock_alloc_send_pskb() succeeds, let's use blocking call. Also, in case an unexpected error occurred, let's break the loop if blocking nfc_alloc_send_skb() failed. [1] https://syzkaller.appspot.com/bug?id=4a131cc571c3733e0eff6bc673f4e36ae48f19c6Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by:
syzbot <syzbot+d29d18215e477cfbfbdd@syzkaller.appspotmail.com> Signed-off-by:
-
Santosh Shilimkar authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit f1693c63 upstream. Loop transport which is self loopback, remote port congestion update isn't relevant. Infact the xmit path already ignores it. Receive path needs to do the same. Reported-by: syzbot+4c20b3866171ce8441d2@syzkaller.appspotmail.com Reviewed-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Eric Biggers authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit c604cb76 upstream. My recent fix for dns_resolver_preparse() printing very long strings was incomplete, as shown by syzbot which still managed to hit the WARN_ONCE() in set_precision() by adding a crafted "dns_resolver" key: precision 50001 too large WARNING: CPU: 7 PID: 864 at lib/vsprintf.c:2164 vsnprintf+0x48a/0x5a0 The bug this time isn't just a printing bug, but also a logical error when multiple options ("#"-separated strings) are given in the key payload. Specifically, when separating an option string into name and value, if there is no value then the name is incorrectly considered to end at the end of the key payload, rather than the end of the current option. This bypasses validation of the option length, and also means that specifying multiple options is broken -- which presumably has gone unnoticed as there is currently only one valid option anyway. A similar problem also applied to option values, as the kstrtoul() when parsing the "dnserror" option will read past the end of the current option and into the next option. Fix these bugs by correctly computing the length of the option name and by copying the option value, null-terminated, into a temporary buffer. Reproducer for the WARN_ONCE() that syzbot hit: perl -e 'print "#A#", "\0" x 50000' | keyctl padd dns_resolver desc @s Reproducer for "dnserror" option being parsed incorrectly (expected behavior is to fail when seeing the unknown option "foo", actual behavior was to read the dnserror value as "1#foo" and fail there): perl -e 'print "#dnserror=1#foo\0"' | keyctl padd dns_resolver desc @s Reported-by:
syzbot <syzkaller@googlegroups.com> Fixes: 4a2d7892 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Florian Westphal authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit 11ff7288 upstream. the ebtables evaluation loop expects targets to return positive values (jumps), or negative values (absolute verdicts). This is completely different from what xtables does. In xtables, targets are expected to return the standard netfilter verdicts, i.e. NF_DROP, NF_ACCEPT, etc. ebtables will consider these as jumps. Therefore reject any target found due to unspec fallback. v2: also reject watchers. ebtables ignores their return value, so a target that assumes skb ownership (and returns NF_STOLEN) causes use-after-free. The only watchers in the 'ebtables' front-end are log and nflog; both have AF_BRIDGE specific wrappers on kernel side. Reported-by: syzbot+2b43f681169a2a0d306a@syzkaller.appspotmail.com Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Paul Burton authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit b63e132b upstream. The current MIPS implementation of arch_trigger_cpumask_backtrace() is broken because it attempts to use synchronous IPIs despite the fact that it may be run with interrupts disabled. This means that when arch_trigger_cpumask_backtrace() is invoked, for example by the RCU CPU stall watchdog, we may: - Deadlock due to use of synchronous IPIs with interrupts disabled, causing the CPU that's attempting to generate the backtrace output to hang itself. - Not succeed in generating the desired output from remote CPUs. - Produce warnings about this from smp_call_function_many(), for example: [42760.526910] INFO: rcu_sched detected stalls on CPUs/tasks: [42760.535755] 0-...!: (1 GPs behind) idle=ade/140000000000000/0 softirq=526944/526945 fqs=0 [42760.547874] 1-...!: (0 ticks this GP) idle=e4a/140000000000000/0 softirq=547885/547885 fqs=0 [42760.559869] (detected by 2, t=2162 jiffies, g=266689, c=266688, q=33) [42760.568927] ------------[ cut here ]------------ [42760.576146] WARNING: CPU: 2 PID: 1216 at kernel/smp.c:416 smp_call_function_many+0x88/0x20c [42760.587839] Modules linked in: [42760.593152] CPU: 2 PID: 1216 Comm: sh Not tainted 4.15.4-00373-gee058bb4d0c2 #2 [42760.603767] Stack : 8e09bd20 8e09bd20 8e09bd20 fffffff0 00000007 00000006 00000000 8e09bca8 [42760.616937] 95b2b379 95b2b379 807a0080 00000007 81944518 0000018a 00000032 00000000 [42760.630095] 00000000 00000030 80000000 00000000 806eca74 00000009 8017e2b8 000001a0 [42760.643169] 00000000 00000002 00000000 8e09baa4 00000008 808b8008 86d69080 8e09bca0 [42760.656282] 8e09ad50 805e20aa 00000000 00000000 00000000 8017e2b8 00000009 801070ca [42760.669424] ... [42760.673919] Call Trace: [42760.678672] [<27fde568>] show_stack+0x70/0xf0 [42760.685417] [<84751641>] dump_stack+0xaa/0xd0 [42760.692188] [<699d671c>] __warn+0x80/0x92 [42760.698549] [<68915d41>] warn_slowpath_null+0x28/0x36 [42760.705912] [<f7c76c1c>] smp_call_function_many+0x88/0x20c [42760.713696] [<6bbdfc2a>] arch_trigger_cpumask_backtrace+0x30/0x4a [42760.722216] [<f845bd33>] rcu_dump_cpu_stacks+0x6a/0x98 [42760.729580] [<796e7629>] rcu_check_callbacks+0x672/0x6ac [42760.737476] [<059b3b43>] update_process_times+0x18/0x34 [42760.744981] [<6eb94941>] tick_sched_handle.isra.5+0x26/0x38 [42760.752793] [<478d3d70>] tick_sched_timer+0x1c/0x50 [42760.759882] [<e56ea39f>] __hrtimer_run_queues+0xc6/0x226 [42760.767418] [<e88bbcae>] hrtimer_interrupt+0x88/0x19a [42760.775031] [<6765a19e>] gic_compare_interrupt+0x2e/0x3a [42760.782761] [<0558bf5f>] handle_percpu_devid_irq+0x78/0x168 [42760.790795] [<90c11ba2>] generic_handle_irq+0x1e/0x2c [42760.798117] [<1b6d462c>] gic_handle_local_int+0x38/0x86 [42760.805545] [<b2ada1c7>] gic_irq_dispatch+0xa/0x14 [42760.812534] [<90c11ba2>] generic_handle_irq+0x1e/0x2c [42760.820086] [<c7521934>] do_IRQ+0x16/0x20 [42760.826274] [<9aef3ce6>] plat_irq_dispatch+0x62/0x94 [42760.833458] [<6a94b53c>] except_vec_vi_end+0x70/0x78 [42760.840655] [<22284043>] smp_call_function_many+0x1ba/0x20c [42760.848501] [<54022b58>] smp_call_function+0x1e/0x2c [42760.855693] [<ab9fc705>] flush_tlb_mm+0x2a/0x98 [42760.862730] [<0844cdd0>] tlb_flush_mmu+0x1c/0x44 [42760.869628] [<cb259b74>] arch_tlb_finish_mmu+0x26/0x3e [42760.877021] [<1aeaaf74>] tlb_finish_mmu+0x18/0x66 [42760.883907] [<b3fce717>] exit_mmap+0x76/0xea [42760.890428] [<c4c8a2f6>] mmput+0x80/0x11a [42760.896632] [<a41a08f4>] do_exit+0x1f4/0x80c [42760.903158] [<ee01cef6>] do_group_exit+0x20/0x7e [42760.909990] [<13fa8d54>] __wake_up_parent+0x0/0x1e [42760.917045] [<46cf89d0>] smp_call_function_many+0x1a2/0x20c [42760.924893] [<8c21a93b>] syscall_common+0x14/0x1c [42760.931765] ---[ end trace 02aa09da9dc52a60 ]--- [42760.938342] ------------[ cut here ]------------ [42760.945311] WARNING: CPU: 2 PID: 1216 at kernel/smp.c:291 smp_call_function_single+0xee/0xf8 ... This patch switches MIPS' arch_trigger_cpumask_backtrace() to use async IPIs & smp_call_function_single_async() in order to resolve this problem. We ensure use of the pre-allocated call_single_data_t structures is serialized by maintaining a cpumask indicating that they're busy, and refusing to attempt to send an IPI when a CPU's bit is set in this mask. This should only happen if a CPU hasn't responded to a previous backtrace IPI - ie. if it's hung - and we print a warning to the console in this case. I've marked this for stable branches as far back as v4.9, to which it applies cleanly. Strictly speaking the faulty MIPS implementation can be traced further back to commit 856839b7 ("MIPS: Add arch_trigger_all_cpu_backtrace() function") in v3.19, but kernel versions v3.19 through v4.8 will require further work to backport due to the rework performed in commit 9a01c3ed ("nmi_backtrace: add more trigger_*_cpu_backtrace() methods"). Signed-off-by:
Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19597/ Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org # v4.9+ Fixes: 856839b7 ("MIPS: Add arch_trigger_all_cpu_backtrace() function") Fixes: 9a01c3ed ("nmi_backtrace: add more trigger_*_cpu_backtrace() methods") [ Huacai: backported to 4.4: Restruction since generic NMI solution is unavailable ] Signed-off-by:
Huacai Chen <chenhc@lemote.com> Signed-off-by:
-
Paul Burton authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit 5a267832 upstream. The generic nmi_cpu_backtrace() function calls show_regs() when a struct pt_regs is available, and dump_stack() otherwise. If we were to make use of the generic nmi_cpu_backtrace() with MIPS' current implementation of show_regs() this would mean that we see only register data with no accompanying stack information, in contrast with our current implementation which calls dump_stack() regardless of whether register state is available. In preparation for making use of the generic nmi_cpu_backtrace() to implement arch_trigger_cpumask_backtrace(), have our implementation of show_regs() call dump_stack() and drop the explicit dump_stack() call in arch_dump_stack() which is invoked by arch_trigger_cpumask_backtrace(). This will allow the output we produce to remain the same after a later patch switches to using nmi_cpu_backtrace(). It may mean that we produce extra stack output in other uses of show_regs(), but this: 1) Seems harmless. 2) Is good for consistency between arch_trigger_cpumask_backtrace() and other users of show_regs(). 3) Matches the behaviour of the ARM & PowerPC architectures. Marked for stable back to v4.9 as a prerequisite of the following patch "MIPS: Call dump_stack() from show_regs()". Signed-off-by:
-
Ping-Ke Shih authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit 9a98302d upstream. Without this patch, firmware will not run properly on rtl8821ae, and it causes bad user experience. For example, bad connection performance with low rate, higher power consumption, and so on. rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and each firmware has firmware data buffer and size individually. Original code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and this mismatch causes firmware checksum error, then firmware can't start. In this situation, driver gives message "Firmware is not ready to run!". Fixes: fe89707f ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware") Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Cc: Stable <stable@vger.kernel.org> # 4.0+ Reviewed-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Gustavo A. R. Silva authored
BugLink: https://bugs.launchpad.net/bugs/1790884 commit 676bcfec upstream. t.qset_idx can be indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c:2286 cxgb_extension_ioctl() warn: potential spectre issue 'adapter->msix_info' Fix this by sanitizing t.qset_idx before using it to index adapter->msix_info Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
-
Alex Vesker authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit d412c31d ] The command interface can work in two modes: Events and Polling. In the general case, each time we invoke a command, a work is queued to handle it. When working in events, the interrupt handler completes the command execution. On the other hand, when working in polling mode, the work itself completes it. Due to a bug in the work handler, a command could have been completed by the interrupt handler, while the work handler hasn't finished yet, causing the it to complete once again if the command interface mode was changed from Events to polling after the interrupt handler was called. mlx5_unload_one() mlx5_stop_eqs() // Destroy the EQ before cmd EQ ...cmd_work_handler() write_doorbell() --> EVENT_TYPE_CMD mlx5_cmd_comp_handler() // First free free_ent(cmd, ent->idx) complete(&ent->done) <-- mlx5_stop_eqs //cmd was complete // move to polling before destroying the last cmd EQ mlx5_cmd_use_polling() cmd->mode = POLL; --> cmd_work_handler (continues) if (cmd->mode == POLL) mlx5_cmd_comp_handler() // Double free The solution is to store the cmd->mode before writing the doorbell. Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Konstantin Khlebnikov authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 7e85dc8c ] When blackhole is used on top of classful qdisc like hfsc it breaks qlen and backlog counters because packets are disappear without notice. In HFSC non-zero qlen while all classes are inactive triggers warning: WARNING: ... at net/sched/sch_hfsc.c:1393 hfsc_dequeue+0xba4/0xe90 [sch_hfsc] and schedules watchdog work endlessly. This patch return __NET_XMIT_BYPASS in addition to NET_XMIT_SUCCESS, this flag tells upper layer: this packet is gone and isn't queued. Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Jason Wang authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit b8f1f658 ] Sock will be NULL if we pass -1 to vhost_net_set_backend(), but when we meet errors during ubuf allocation, the code does not check for NULL before calling sockfd_put(), this will lead NULL dereferencing. Fixing by checking sock pointer before. Fixes: bab632d6 ("vhost: vhost TX zero-copy support") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Ilpo Järvinen authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 1236f22f ] If SACK is not enabled and the first cumulative ACK after the RTO retransmission covers more than the retransmitted skb, a spurious FRTO undo will trigger (assuming FRTO is enabled for that RTO). The reason is that any non-retransmitted segment acknowledged will set FLAG_ORIG_SACK_ACKED in tcp_clean_rtx_queue even if there is no indication that it would have been delivered for real (the scoreboard is not kept with TCPCB_SACKED_ACKED bits in the non-SACK case so the check for that bit won't help like it does with SACK). Having FLAG_ORIG_SACK_ACKED set results in the spurious FRTO undo in tcp_process_loss. We need to use more strict condition for non-SACK case and check that none of the cumulatively ACKed segments were retransmitted to prove that progress is due to original transmissions. Only then keep FLAG_ORIG_SACK_ACKED set, allowing FRTO undo to proceed in non-SACK case. (FLAG_ORIG_SACK_ACKED is planned to be renamed to FLAG_ORIG_PROGRESS to better indicate its purpose but to keep this change minimal, it will be done in another patch). Besides burstiness and congestion control violations, this problem can result in RTO loop: When the loss recovery is prematurely undoed, only new data will be transmitted (if available) and the next retransmission can occur only after a new RTO which in case of multiple losses (that are not for consecutive packets) requires one RTO per loss to recover. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Tested-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
-
Yuchung Cheng authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit c860e997 ] Fast Open key could be stored in different endian based on the CPU. Previously hosts in different endianness in a server farm using the same key config (sysctl value) would produce different cookies. This patch fixes it by always storing it as little endian to keep same API for LE hosts. Reported-by:
Daniele Iamartino <danielei@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Jiri Slaby authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 0ee1f473 ] When unplugging an r8152 adapter while the interface is UP, the NIC becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to napi_disable, but the napi is already deleted by disconnect above. So the first while loop in napi_disable never finishes. This results in complete deadlock of the network layer as there is rtnl_mutex held by unregister_netdev. So avoid the call to napi_disable in rtl8152_close when the device is already gone. The other calls to usb_kill_urb, cancel_delayed_work_sync, netif_stop_queue etc. seem to be fine. The urb and netdev is not destroyed yet. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: linux-usb@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
-
Sudarsana Reddy Kalluru authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit bb7858ba ] Memory size is limited in the kdump kernel environment. Allocation of more msix-vectors (or queues) consumes few tens of MBs of memory, which might lead to the kdump kernel failure. This patch adds changes to limit the number of MSI-X vectors in kdump kernel to minimum required value (i.e., 2 per engine). Fixes: fe56b9e6 ("qed: Add module with basic common support") Signed-off-by:
Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by:
Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by:
-
Eric Dumazet authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 12b03558 ] After commit 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"), sungem owners reported the infamous "eth0: hw csum failure" message. CHECKSUM_COMPLETE has in fact never worked for this driver, but this was masked by the fact that upper stacks had to strip the FCS, and therefore skb->ip_summed was set back to CHECKSUM_NONE before my recent change. Driver configures a number of bytes to skip when the chip computes the checksum, and for some reason only half of the Ethernet header was skipped. Then a second problem is that we should strip the FCS by default, unless the driver is updated to eventually support NETIF_F_RXFCS in the future. Finally, a driver should check if NETIF_F_RXCSUM feature is enabled or not, so that the admin can turn off rx checksum if wanted. Many thanks to Andreas Schwab and Mathieu Malaterre for their help in debugging this issue. Signed-off-by:
Meelis Roos <mroos@linux.ee> Reported-by:
Mathieu Malaterre <malat@debian.org> Reported-by:
Andreas Schwab <schwab@linux-m68k.org> Tested-by:
-
Alex Vesker authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 603b7bcf ] The NULL character was not set correctly for the string containing the command length, this caused failures reading the output of the command due to a random length. The fix is to initialize the output length string. Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by:
-
Eric Dumazet authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 0ce4e70f ] To compute delays, better not use time of the day which can be changed by admins or malicious programs. Also change ccid3_first_li() to use s64 type for delta variable to avoid potential overflows. Signed-off-by:
-
Eric Dumazet authored
BugLink: https://bugs.launchpad.net/bugs/1790884 [ Upstream commit 74174fe5 ] On fast hosts or malicious bots, we trigger a DCCP_BUG() which seems excessive. syzbot reported : BUG: delta (-6195) <= 0 at net/dccp/ccids/ccid3.c:628/ccid3_hc_rx_send_feedback() CPU: 1 PID: 18 Comm: ksoftirqd/1 Not tainted 4.18.0-rc1+ #112 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113 ccid3_hc_rx_send_feedback net/dccp/ccids/ccid3.c:628 [inline] ccid3_hc_rx_packet_recv.cold.16+0x38/0x71 net/dccp/ccids/ccid3.c:793 ccid_hc_rx_packet_recv net/dccp/ccid.h:185 [inline] dccp_deliver_input_to_ccids+0xf0/0x280 net/dccp/input.c:180 dccp_rcv_established+0x87/0xb0 net/dccp/input.c:378 dccp_v4_do_rcv+0x153/0x180 net/dccp/ipv4.c:654 sk_backlog_rcv include/net/sock.h:914 [inline] __sk_receive_skb+0x3ba/0xd80 net/core/sock.c:517 dccp_v4_rcv+0x10f9/0x1f58 net/dccp/ipv4.c:875 ip_local_deliver_finish+0x2eb/0xda0 net/ipv4/ip_input.c:215 NF_HOOK include/linux/netfilter.h:287 [inline] ip_local_deliver+0x1e9/0x750 net/ipv4/ip_input.c:256 dst_input include/net/dst.h:450 [inline] ip_rcv_finish+0x823/0x2220 net/ipv4/ip_input.c:396 NF_HOOK include/linux/netfilter.h:287 [inline] ip_rcv+0xa18/0x1284 net/ipv4/ip_input.c:492 __netif_receive_skb_core+0x2488/0x3680 net/core/dev.c:4628 __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693 process_backlog+0x219/0x760 net/core/dev.c:5373 napi_poll net/core/dev.c:5771 [inline] net_rx_action+0x7da/0x1980 net/core/dev.c:5837 __do_softirq+0x2e8/0xb17 kernel/softirq.c:284 run_ksoftirqd+0x86/0x100 kernel/softirq.c:645 smpboot_thread_fn+0x417/0x870 kernel/smpboot.c:164 kthread+0x345/0x410 kernel/kthread.c:240 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:412 Signed-off-by:
-
